SM-DV8GN11 User`s Manual
Contents
1. To to set the desired hour click on the second box on the same row to set the minutes Repeat steps above for all other days Once complete make sure to click on OK to save changes EXCEPTION This feature will alert you when the either the hard drive is full or has an error Type Select HDD Full or HDD Error a n Buzzer Check box to enable or disable buzzer sound Alarm Upload Send E Alarm Upload Check box to enable or disable alarm uploads Qu Send an email Check box to enable or disable email notifications Alarm out Check box to enable or disable alarm out Faleti Type HOG Full FR When done click OK to exit to the mail menu then EXIT and select Yes and exit to confirm save 10 OPERATION continued P T Z Configuration Speed dome camera only not included check for availability at www sumasmedia com Set the channel number of decoder including velocity data bit stop bit checkout and stream control in serial port device menu The values of these items must match the connected serial device The default values are 8 data bits 1 stop bit none checkout bit and hardware stream control These data cannot be revised by customer Part Baud Rate Device Tyre Channel P T 1 Protocol P T 1 Address Copy To Keyboard select Hem Port Use RS485 on the back of the unit Baud Rate Select from 19200 9600 4800 2400 and 1200 The selected2. or Original Backup Channel Select which channel you want to backup 1 8 and press OK Playback Screen Mode will allow you to select how many and which channel s you want the playback to show on Select from 1 Chan 2 Chan or 4 Chan and then select which channels 1 8 once selected press Playback to view the recorded event Unit will not play the record event You can also click on List and Search to view and select from list of recorded events on the selected time frame Right click anywhere on the screen to bring up the playback controls PLAY STOP FB FF PREV NEXT CHAN Once confirmed press STOP to go back to the Backup menu and click on BACKUP and select the drive you want to backup to and click OK Note Time of backup may vary depending on the size of the file s and type of media When backing up with an external CDRW DVDRW drive make sure that the burning process completely finishes when your devise s indicator light turn off before removing the disc removing the disc prematurely may result incomplete transfer and the disc will not be readable by your PC TOOLS This will give you access to the following Load Default This will reset the DVR to the factory settings Update Firmware Use to update the firmware of the system HDD Mng Use to format or do data recovery Data Recovery is ONLY used if the hard drive has some bad sectors The system will try to recover any file in the bad
3. Click to select a menu option during live viewing in split screen double click on a channel to view the selected channel in full screen Double click the channel again to return to split screen view e Right Button 2 Click to open the Sub Menu and or to go back to the previous screen In playback mode click to bring up play controls e Wheel 3 No function Icon Indicators The different symbols displayed on the screen indicating different information Some have no icon some have icon Please find the indicating meaning as below En o pe Pl b gt 44 a w Video recording symbol Video recording symbol Video recording symbol Playing symbol Single frame symbol FF symbol FR symbol Timing symbol Alert symbol PTZ symbol USB Symbol Time display The green round icon indicates manual recording state The yellow round icon indicates timing recording state The red round icon indicates alarm recording state Indicates the recording is being played Indicates pause in single frame playing state Indicates fast forward followed such as x2 indicate the fast forward speed Indicates fast rewind Followed such as x4 indicate the fast reward speed Indicates the video recorder is in timing state Indicates Alarm Alert mode is on Indicates PTZ Pan Tilt Zoom controlled Indicates the USB interface is connected Playing time or recording time 5 OPERATION Turning the unit on off P
4. Customize Quality To customize record quality click Customize Quality Video Quality Definition screen will show up Under Main Stream key in the desired quality specified by MB Hr megabytes per hour for Best Superior Medium Normal Custom Under Secondary Stream key in the desired quality specified by MB Hr megabytes per hour for Best Superior Medium Normal Custom Default To reset video quality configuration to factory defaults click on Default then click OK to exit to the previous screen click OK again to go to the main menu and click EXIT and select YES to confirm save and exit IN Note The higher the video quality the more hard drive usage space it will take up OPERATION continued Network This will allow you to setup the network for remote viewing Internet Explorer 6 0 or higher required CET ME mu Cairel Port 1367 E E P Address E Mail Contig Subnet Mal Gateway nee Video Stream Port EE Remote Serveri Talkback Siream Port EX HTTP Port k a ER Remote Pervert el IP Configuration Screen Port Configuration Screen Email Configuration Screen Static IP Setup To input the IP configuration click on IP Config and select Static IP Fill out all appropriate fields IP Address Subnet Mask Gateway DNS Click on Port Config and verify that all fields are filled out Control Port 3357 Video Stre
5. Le 0 ge Y ci USB Mouse Remote Control Hard Drive Screws GUmMAS vs SM DVEGN 1 1 USER OPERATION MANUAL Software CD User Manual 16
6. 3 SB 05 05 oo of Assistant 1 amp 2 06 sadis f Sun DUNNER ANY 19 41 33 2011 02 11 19 41 35 2041 02 11 19 41 33 z Preset Setting Sm 090 Get Preset CHANNELS zoom Focus Zoom Iris BRIGHTNESS HUE or or MAR ES ees oT BRIGHTNESS HUE ENABLED FULL SCREEN DISABLED TERRE CONTRAST SHARPNESS VIEW SET STOP RECORD QUAD SCREEN 8 GHANNEL VIEW VIEW Logout To log off remote viewing View To view cameras Playback To playback recorded events Log To view system logs DVR configuration To enter DVR configuration Basic info Channel config and Network config Local setting To specify local storage capture save paths Camera channels Double click to enable disable camera channel Viewing pane Live and Playback viewing window Full screen view To view selected channel in full screen mode Quad screen view To switch from full screen or 8 channel view to quad view 8 channel view To switch from full or quad view to 8 channel view Stop Live To stop viewing or playback click to view live view when stopped Capture Take screen shot of selected camera channel Screenshot is save on the local hard drive Record To start recording what s currently on the screen to your local hard drive Brightness Hue Contrast Sharpness Adjust up down to get the desired video settings Brightness Hue Contrast and Sharpness Reset Resets all video setting to default PTZ Controls A Y gt Up Down
7. This feature will retrieve what the current settings from the camera Keyboard Select the appropriate keyboard type L C Pinerve Samlink Mianvan Copy to This feature will enable you to copy the PTZ settings 1 or all the channels To copy simply select the channel you want to copy to then click on Copy When done click OK to exit to the mail menu then EXIT and select Yes and exit to confirm save Preview This feature will cycle through the different channels automatically when nobody is operating the unit To 4 Cyelic Serean Mode One Chan E Four Chan all chen E ELLE Interval Input the desired interval time from 0 99 seconds Cyclic Screen Mode Select between One Chan this will cycle one channel at a time Four Chan this will cycle 4 channels at a time All Chan when activated in conjunction with One Chan or Four Chan or both the cycle will include all channels in the mix Activate Make sure to check this box to activate this feature When done click OK to exit to the mail menu then EXIT and select Yes and exit to confirm save 11 USER OPERATION continued This will allow you to change the default password admin 88888888 Operator 1 3 66666666 to your desired password and also add up to 8 different users Admin Operator 1 2 3 8 Change Set Password To change password click on USER from the main menu
8. Enable or cancel timing recording Disabled not available 16 channel view disabled not available Mute button Enable and disables sound Start stop video recording The green 16 O REC STOP round icon on the screen indicates manual recording state gt Plays stops the last recorded playback Pll Indicates two functions pause or move 17 to the next frame It will appear in the image while it pause or is in frame step playing eo ae Press to search the next recorded clip ESC ESC Press to exit out of the menu et Press to enter search mode for recorded events 1 22 DISPLAY Enables disables display icons on the screen Press to silent the buzzer alarm II channel vien o 24 Quad channel display MOUSE OPERATION The mouse is the primary input device for navigating system menus NOTE Unless otherwise noted all system functions described in this manual are achieved using To use a mouse with the system the mouse 1 Connect the included USB mouse to the USB MOUSE port on the back of the unit NOTE The top USB port is designed for external USB drives for data backup USB flash External HDD etc Do not connect a USB flash drive to the bottom USB port on the rear panel a we Le sm D al y 1 le i s j rr Y e g i Connect a USB mouse to the bottom USB port on the rear panel 2 Use the mouse buttons to perform the following e Left Button 1
9. Select the which user you want to change set the password Admin Operation 1 2 or 3 Enter the current password under Current PWD default password is 66666666 or 88888888 Under New PWD enter your new password and enter again in Confirm New PWD Authorization Setting Select which setting the operator can access Basic Live Record Network Alarm Set Exception PTZ Preview USER Backup Tools Check Authorization Check if you want the password to be prompted every time you want to access the system Setting Repeat steps above for all the other users When trying to access the menu the unit will ask for a password the entered password will determine which user is logged on Note Password can be up to 8 digits Make sure you write your password in a safe place Only admin can change the password When done click OK to exit to the mail menu then EXIT and select Yes and exit to confirm save BACKUP This will allow you to backup recorded events on the DVR to a USB flash drive an external HDD or an external CDRW DVDRW drive it will also take a minute to start up By Time From D EN LE LE LE L DE LE LE LE LE By Event Type an Paybask Pza PF Backup Char DIRE DS Md h oelect Iam To start backup enter the correct time and date you want to backup From To Select what type of event under By Event Type Normal Alarm All Select the file size Full
10. Sumas Media SM DV8GN11 USER OPERATION MANUAL CONTENT INTRODUCTION nn nan uses anna ie 1 PRECAUTIONS FEATURES RESTRICTION ABOUT AUDIO RECORDING SPECIFICATION Sa a 2 DVR FRONT and REAR PANEL OPERATION nn nnnnnnnnemnnmnnnenmanmnnmenmnennnnnnnnnnne D REMOTE CONTROL OPERATION c ciiciricciniinancnaca cia 4 MOUSE OPERATION erreren a 5 OPERATION sisiisiisideisuindunduns ee AAA AAA 6 12 ON OFF 6 SUB MENU 6 MAIN MENU 6 BASIC 6 LI VE 7 RECORD 8 NETWORK 9 Alarm 10 Exception 10 PTZ Configuration 11 Preview 11 USER 12 BACKUP 12 TOOLS 12 FAQ Frequently Asked Questions uses snnnsnnssesemenensnnsnsenensmssseses 14 15 PACKAGE CONTENTS cotorra LO For internet viewing Static or Non Static Internet IP address How to check what you have If you re not paying hundreds of dollars for your internet then more than likely you do not have a Static internet IP address You can check your router s SETUP page under internet setup to see if you have static or non static internet IP address Your router will state Static IP on this page if you have a Static IP address if it doesn t display Static IP then you have a non static internet IP address Note Before calling Sumas Media for assistance please have your IP address ready Read below Different brands and models of routers will have different ways on how to check you internet IP address Please check your routers user m
11. alpha numeric pad 1 abc 2 def O etc and key in your desired name for channel 1 upper lower case indicator will appear on the bottom left corner or click on Select and pick from a list Brightness Contrast Hue Sharpness Click on 1 on each option to change to your desired video outlook Privacy Masking Click on the circle next to privacy masking to enable disable feature Click on Mask Area to select the desired area to be masked Up to 4 areas to be masked per channel Click Active beside Mark area 1 Mark area 4 then select the Area To select the desired area to mask simply click and hold the left mouse button then drag the mouse on the desired area to mask right click to exit Repeat steps above for all the other Mark area When done click on Back to return to the previous page Mask Detection Click the circle next to mask detection to enable disable feature Sensitivity Click on the box next to sensitivity and select from the following Lowest Lower Normal High Highest Trigger Record Click ALARM to view and edit the Trigger Record Select which camera 1 8 you want to modify Buzzer Click to enable disable buzzer sound when triggered Alarm Upload Click to enable disable Send an e mail Click to enable disable email notifications Alarm Out Click to enable disable alarm feed Prerecord This determines how long the system
12. by right mouse button will only work with Manual recording This cannot stop recording when the DVR is on scheduled recording mode lt gt You must click on Timer Stop first to stop recording If the recording does not stop click on Record Stop to stop the recording 14 FAQ Frequently Asks Questions cont 8 Question Motion detection is not working properly Answer Motion detection is not enabled see page 7 lt gt The setting of motion detection area is not correct see page 7 for setup Sensitivity is too low 9 Question USB backup error or taking too long to start Answer The data exceeds the capacity of backup device The backup device is incompatible or not formatted properly FAT FAT32 The backup device is damaged USB device plugged into the wrong port see page 5 External CDRW DVDRW USB backup usually takes about a minute to start 10 Question Remote control cannot work Answer lt gt The distance of remote control is too far or the angle is bad lt gt Remote control battery run out replace batteries 11 Question WEB cannot login Answer Please check the network to see if it is connected Ping XXX xxX xxx xxx DVR IP in CMD to check if the Internet is linked properly Recommended to use Internet Explorer browser v6 0 or higher running on Windows XP or higher operating system ActiveX control has been blocked or disabled Enable or disable the Active X c
13. sector Note Once hard drive is formatted all data will be lost System Log Will list all of the system logs System Log must be enable in the Basic menu Simply enter the dates From To you want to view the logs from and click Log list System Information Shows all of the system configurations System Mng You can reboot or power off the system in this section 12 REMOTE VIEWING Remote viewing requires Internet Explorer IE 6 0 or higher running on Window XP or higher To start remote viewing Make sure that network configuration is properly setup Open IE and type in the IP address for xxx xxx xxx xxx on the address bar Fig 1 For non static IP type in the domain name you have registered from www dyndns com or www no ip com Active X attention bar should pop up Click on the Active X attention bar and select run install Active X controller must be installed in able to run remote viewing If Active X bar does not pop up and log in screen does not come up you must enable Active X in IE internet options Fig 2 and try again Enter the password when prompt and click OK Default password is 88888888 Once logged in quad view should automatically start showing all the active camera views Fig 3 HOMME Fig 1 Fig 2 Control configurations for remote viewing DVR LOCA LOGOUT VIEW PLAYBACK LOG CONFIGURATION SETTING PTZ Control 030 Se 04_04 Channel Select n 7
14. set from O second to 99 minutes Repeat steps above for all other channels Schedule Motion Click on Schedule Motion to set specific time to activate motion detection Set schedule Select the day you want under Date Mon Fri Sat Sun Mon Sun Mon Tue Wed Thur Fri Sat Sun Start time Click on the first box under From and to set the desired hour click on the second on the same row to set the minutes End Time Click on the first box under To to set the desired hour click on the second box on the same row to set the minutes Repeat steps above for all other days Once complete make sure to click on the box next to Activate on the bottom left of the window to activate motion detection schedule Once done with all the changes Click OK to confirm then click Exit and select Yes to save all changes and to close main menu window OPERATION continued Record This will allow you to change the recording video quality and the recording schedule for each channel T o To OF OF OF OF OF OF OF OF OF o enter pubmara Record Screen Schedule Screen To change the recording video quality Select the desired channel to be changed 1 8 Video Resolution CIF Common Image Format is the only choice Video Quality Select from Normal Medium Superior Best Custom Type Select from CBR Constant Bit Rate or VBR Variable Bit
15. will prerecord after a trigger select prerecord time from O seconds to 60 seconds Postrecord This determines how long the unit will record after a trigger select post record time from O seconds to 60 minutes Alarm Output Time This determines how long the alarm output will sound after a trigger select time from O seconds to 60 minutes Video Loss Click on the circle next to video loss to enable disable the video loss indicator Click Alarm and follow the steps above for Trigger Record setup Motion Detection Click on the circle next to Motion Detection to enable disable feature To change sensitivity Click on the box next to sensitivity and select from the following Lowest Lower Normal High Highest Area Click on Area to specify which areas you want to have the motion detection on and off The selected areas will turn red section A in image above Trees Flags and other constant moving objects should be grayed out to save hard drive space Right click to exit Click Alarm and follow the steps above for Trigger Record setup Copy To You can copy the above settings to 1 or all the channels by the selecting the desired option under Copy To then click Copy to copy to the desired channel s Post record time This feature determines how long the unit will record after motion is detected Event Type Click to select between Normal or Alarm Postrecord Time You can
16. 1 0Vp p impedance 750 BNC 1 VGA port 1 RCA port G U ns Video in Video out Video display 8ch 1 8channel switch Video system NTSC 30 frames sec for north America Audio input 1 RCA port Audio output 1 RCA port Alarm sensor input video dynamic detecting alarm Alarm i A video loss alarm disk full alarm Alarm input 2 way switching capacity Alarm output 1 way switching capacity H 264 NTSC system Display Resolution 704 x 480 Picture Resolution compressed resolution 350 x 240 NTSC for north America only Supports SATA HDD up to 2TB RJ45 10M 100M adaptive support LAN WAN amp ADSL dynamic IP networking Picture compression Data storage Network interface Monitoring methods IE monitoring phone monitoring e mail alert function Allows up to 8 remote viewers at once Support for USB and Network Backup Support for USB mouse remote control RS485 PTZ camera control speed dome camera only not included Support USB firmware upgrade AC 110 240V DC 12V 2A Voltage input Voltage output Power Consumption 8W without HDD Working temperature 41 F 122 F humidity lt 90 Storage temperature 4 F 158 F humidity lt 95 12V DC 12V Dimension 10 16 x 1 97 x 9 37 W x H x D Weight Ibs Net weight 3 10 Gross weight 4 10 DVR FRONT and REAR PANEL OPERATION CHANNEL LED INDICATOR SELECTOR LIGHT CSUMAS re POWER Net REC DIGITAL VIDEO RECORDER BUTT
17. Left Right or auto cruise center button Channel Select Select which channel has the PTZ Speed Dome camera Assistant 1 2 Some speed dome cameras have extra features Wiper and Sun shade that can be controlled by these 2 buttons Preset Setting Select the preset angle of the speed dome camera Preset Click after setting the preset setting to confirm angle setup Get Click to get the current angle settings Focus Zoom Iris Press to get the desired settings Cell Phone Viewing This DVR also supports remote viewing via cell phone Support cell phones are iPhone Nokia Motorola Samsung HP etc Please refer to the included CD for instructions and cell phone software 13 FAQ Frequently Asked Questions If your problem is not listed below please call our toll free number for more support Question DVR will not power up Answer Check the adaptor input to the DVR Check the power supply line connection going to the wall outlet Test another device on the wall socket to make sure there is power Question DVR is rebooting automatically or stopped after starting the DVR for several minutes Answer lt gt Instability or low input voltage lt gt Bad sector on the hard drive or the hard drive has gone bad Power supply output is not enough or wrong voltage power supply lt gt Over heating dusty or high humidity environment to operate Question No output of signal channel multi channel or all channel v
18. ON PLAY PAUSE MENU ENTER INFO FAST FORWARD REWIND SEARCH CLEAR QUAD RECORD RECORD STOP Channel Selector Press to make channel full screen LED Indicator Indicates what is active on the unit PTZ ESC Brings out PTZ controls ESC while in menu Power Button Press to turn unit ON OFF Menu Enter Press to bring out menu or select item in menu Info Press to display system info Search Press to search recorded events Clear Press to delete inputted character s Quad Press to switch between 8 qual single screen views Play Pause Press to play or pause recorded events Fast forward Press to increase the play speed Rewind Press to decrease the play speed Record Press to manually record Record Stop Press to stop manual recording BNC Video RCA VIDEO RCA AUDIO Camera Input OUTPUT INPUT RCA AUDIO OUTPUT 0000 OO Q e O ly dor j i 5 Video In MOT 8NG113321 3 Audio In Audio en USB PORTS PTZ and ALARM VGA VIDEO RJ485 DC 12V INTERFACE INPUT POWER INPUT REMOTE CONTROL OPERATION unit OFF keys recording screen 4 Indicates fast rewind 1x 2x 4x 8x 16x 32x gt gt Indicates fast forward 2x 4x 8x 16x e gt Press to go to the beginning of the clip that is currently playing me Press to go to the last recorded clip NS Volume control for audio recording and playback Menu Confirm Enter into device menu and confirm setting Use key to move cursor Up Down Left Right
19. Rate Frame Rate Select from 1 to 30 F S Frames per Second Audio You can enable audio recording by select Y or disable by selecting N Secret Record When enabled the display on selected camera will turn white on the monitor Position This feature will allow to position the Date Time of the schedule time to any position on the screen Schedule Record To Setup Scheduled Recording Click on Setup next to Schedule Record the date and time setup screen will show up Under Date Click to select day Mon Fri Sat Sun Mon Sun Mon Tues Wed Thur Fri Sat Sun Start time Click on the first box under From and to set the desired hour click on the second box on the same row to set the minutes End Time Click on the first box under To to set the desired hour click on the second box on the same row to set the minutes Repeat steps above for all other days Once complete make sure to click on OK to save changes Copy To Allows you to copy the same settings to 1 or all of the channels To copy settings to 1 or all channels select the desire channel from the pop up screen All Chi Ch2 Ch3 then click on Copy a message on the bottom left of the screen will say Copy completely Video Quality Definition MA Kkbpi 300 667 Superior 200 dii Normal EG dti h sum MEH kbps EU 314 Superior KEK 113 Normal an A RP EME Customize Quality Screen
20. am 3358 Talkback Stream 3360 HTTP port 80 Note When using a router make sure all of these ports are properly forwarded open to be able to view outside the local network Check router manual for port forwarding options DHCP This will automatically configure and assign an IP address to the system To view the assigned IP address simply right click anywhere on the screen and select SYSTEM INFO or go to the main menu select TOOLS and click on Sys Information The IP address will view display towards the bottom of the screen Once the IP address is acquired you can now start remote viewing from a local computer by typing the IP address on the internet explorer search bar Note The DVR s IP address might change if the DVR is rebooted or after a power failure This network configuration is limited to local remote viewing DDNS Setup Use for non static IP address Click on DDNS Config to configure DNS settings If you don t have a registered domain name please visit www dyndns com or www no ip com to setup a free domain name and follow the free account setup make sure to select dyndns org or no ip org Once an account has been setup click on DDNS Click on the server and select dyndns org or no ip org Under Account input your account user name and under PWD input your password from www dyndns com or www no ip com Under Hostname
21. anual or call you internet provider for assistance If you cannot see the setup page or the internet IP is not shown or you re not sure please contact your internet service provider for assistance Cell phone remote viewing referred to include CD in package INTRODUCTION This 8 channel H 264 compression DVR has all the present technology included It also comes with 1 audio input for the most important area monitoring recording Unit comparison with other brand is we have put up effort to compact all the hardware to present you a unique design and small enough to hide away DVR For electronic gadget we all know the small the better so there we re giving you a better DVR We ve engineered and imbibed a newer technology for the not yet coming to market H 323 compression technology on playback it will enhance the graphic video to an HD clarity resolution Enjoy your new device and look forward for updates upgrades even newer products at www sumasmedia com AUDIO RESTRICTION Audio recording ts illegal in some states such as California So please check with your local law enforcement to confirm it s allowed in your area without violating the law PRECAUTIONS For your safety while using the DVR and to prolong device life please pay attention to the following details o When installing device please comply with all the electric product safety criteria o Power and ground o Do not touch the power and DVR with a wet hand
22. can also be controlled using the remote control See page 4 for remote control functions Main Menu Select and click on SETTING while on the submenu and key in the default password 88888888 admin You can also press MENU on the remote to bring up the main menu The Main Menu will now show up and display the following BASI C LI VE RECORD NETWORK ALARMSET EXCEPTI ON P T Z PREVI EW USER BACKUP TOOLS EXIT Input PWD id ORD HETRAR LEE ALARM A FEE ere TOOLE ETT Delete Exit Main Menu Password Input Window Time Adjust Screen On Screen Numeric Keypad BASIC Video Format Click to select from NTSC or PAL when using in US TV system need to set to NTSC Language Click to select from the following English Spanish Chinese Dutch French Turkish Russian Polish Hungarian Danish Italiano Czech Portuguese Brightness Click to adjust screen brightness DVR ID If you have multiple DVR s you can set a specific numeric ID for each one up to 8 characters Enable System Log This will log all the events Panel Lock Enable to lock the main menu this will require a password every time the main menu is accessed Wait Set the wait time under for the panel lock from Omin to 99mins Screen Saver This feature will turn off the screen with the selected time from 2 5 15 30mins 1 5hrs or never Watermark The watermark is half transparent While it s used it will appear at the right c
23. ecord This determines how long the system will prerecord after a trigger select prerecord time from Oseconds to 60 seconds Postrecord This determines how long the unit will record after a trigger select post record time from 0 seconds to 60 minutes Alarm Output Time This determines how long the alarm output will sound after a trigger select time from O seconds to 60 minutes Copy to This feature will enable you to copy the alarm settings 1 or 2 to the other alarm input 1 or 2 To copy simply select the alarm input you want to copy to then click on Copy Alarm Out There is only 1 alarm output to select Alarm Output Type Click on the box and select from NO If alarm input is connected to normal opened alarm or NC If the alarm input is connected to a normal closed alarm Copy To This feature is disabled due only 1 alarm output Alert Delay Enter the alert delay time from 1 second to 99 minutes Schedule Alert To Setup Scheduled Alert Click on Schedule Alert the date and time setup screen will show up Operation Click the box under operation and select operation type Alarm On Alarm Off Alarm Out Date Click the box under date to select day Mon Fri Sat Sun Mon Sun Mon Tues Wed Thur Fri Sat Sun Start time Click on the first box under From and to set the desired hour click on the second box on the same row to set the minutes End Time Click on the first box under
24. enter the domain name you have created from www dyndns com or www no ip com no need include dyndns org or no ip org Click on Activate and then click on OK Click OK again to exit to the main menu then click EXIT and confirm the save and exit Email Configuration From Input the desired name you want the email to show up from To Input the desired email address you want to received the email s to Cc Input the desired email address that you want to have a Carbon Copy sent to Smpt server Input your emails SMTP server information Account Input the email address that you are using to send out the emails Password Input your email password then click ok to exit email configuration Click OK again to exit to the main menu then click EXIT and confirm the save and exit Router Setup Input DNS info from www dyndns org or www no ip com that you have created into the DDNS setup page on your router You must enable port forwarding for the following ports 3356 3357 3358 3359 3360 and HTTP port 80 Once all the settings are inputted correctly make sure you save and reboot your router Once the router has rebooted open internet explorer browser on your computer and type the domain name you have registered with www dyndns org or www no ip com example http sumasmedia dyndns org Note Different brands of routers will have different ways on how to enab
25. ideo blue screen Answer Please check camera s AC adaptor connection lt gt Please check the camera s BNC connection on the back of the DVR and to the camera Make sure they are both locked in place lt gt Try swapping the camera connections to determine if there is a defective camera lt gt Make sure the unit is set to NTSC see Basic setup on page 6 Question DVR cannot record after startup Answer lt gt Make sure the power adaptor is DC 12V Confirm the HDD is formatted To format HDD go to Tools then HDD Mng lt gt The HDD has gone bad Go to the system info to check if the unit is recognizing the HDD lt gt Scheduled Recording is enabled Disable Scheduled Recording Question Video is flickering lines across the screen on each channel display is distorted or black and white Answer Check and make sure the LCD monitor and the VGA cable are in good working condition Make sure the system is set to NTSC NOT PAL see Basic setup on page 6 lt gt The recommended monitor display screen resolution is at least 800 x 600 lt gt Reset the system see page 8 Question System time is not correct Answer lt gt A system Reset was done Redo time setup see page 6 Wrong setting or user did not click Time Adjust to confirm see page 6 Question Why the Record Stop by clicking the right mouse button does not work how to stop recording Answer lt gt The Record Stop
26. le port forwarding Please check with your routers user manual to properly setup port forwarding OPERATION continued ALARM This will allow you to setup and configure your alarm settings Alarm in r PRE Alarm epul Tip a capy Te um oi SEX Alarm Quipul Tyee tay Tripper Record wi 6 4 CSS E L Buzzer E Alarm Upload fend a email Alarm Cul di E k Prarecord Time E 5 Poniracerd Time E hi 20 E a E lerm Output Tima Alert Delay E M E 5 LLLLLL LL E A AOS BEBBEBER A ie CERA el Use left or right peleci valus manu to selecl or unrelesi Alarm In Click on the box to select Alarm I n1 or Alarm I n2 Alarm Input Type Click on the box and select from NO If alarm input is connected to normal opened alarm or NC If the alarm input is connected to a normal closed alarm Alarm Click to enter Trigger Record setup Trigger Record Click ALARM to view and edit the Trigger Record Select which camera 1 8 you want to modify Buzzer Click to enable disable buzzer sound when triggered Alarm Upload Click to enable disable This feature uploads the alarm image to a remote host Available when management host is connected The time of image upload depends on time of alarm upload Send an e mail Click to enable disable email notifications Alarm Out Click to enable disable alarm feed Prer
27. lug the included AC adapter to the back of DVR and plug the other end to a wall outlet the unit will display white screen for few seconds before power on and boot up automatically Ifthe unit was already plugged in press the O power button in front of the unit once to turn the DVR on To turn the DVR off press the power button in front of the unit 2x to turn the DVR off Note Once the system has booted up the display will show 8 channels screen view of all the cameras hooked up to the DVR Sub Menu Using the mouse right click anywhere on the screen to bring up the sub menu the screen will now display the following SET TIN SETTING This will display the main menu FILE LIST FILE LIST This will display the recorded file list SYSTEM INFO SYSTEM INFO This will play current system info ALERT time date IP address HDD capacity etc ALERT STOP Alert Enables alarm alert feature TIMER Alert Stop Disables alarm alert feature TIMER STOP TI MER This enables the scheduled record time to activate CLEAR TI MER STOP This disables scheduled record time RECORD Clear Disables alarm sound when pressed RECORD STOP RECORD This enables manual recording Timer must be disabled PLAY FILES RECORD STOP This disables manual recording PTZ PLAY FILES This will play the recorded files starting from the oldest PTZ Pan Tilt Zoom in use with Speed dome cameras not included SUB Menu Note These functions
28. must match with the protocol and parameters of the decoder Devise type Select from No Device PTZ Decoder Keyboard The device is applicable when the option matches with the protocol and parameters of the decoder Channel Select the channel that will have P T Z camera Chi Ch8 PTZ Protocol Select type of decoder protocol The following decoder protocols are present in the program including Panasonic LLW Pelco D Pelco P Lilin Neon Pelco D YA Pelco D SFD Pelco P MK Pelco P JJ Pelco D ZT and Samsung Note Different protocols can be used for different channels PTZ Address Input the address of the decoder connected to the selected screen The address ID must be consistent with the address of the front end decoder or it will lead to failure of control The address ID is set by user PTZ Step Control the speed parameters when moving the PTZ The bigger the step length is the higher the speed will be Present positions This parameter is for setting of speed dome camera The location of the camera the focus aperture and zoom should be present and memorized and a number should be used to mark the setting Present point number Input a number from 00 to 63 Adjust location Press Adjust to enter control status and adjust the location of the dome by direction buttons Press Menu button to return Save To save current setting to the present point number Set your required present points one by one Get
29. o Do not spill liquid on DVR o Do not put any object on DVR o Please use soft dry cloth to clean DVR do not use harmful chemicals o Please unplug power line from power source if the Device is not intended to be used fora long period of time FEATURES H 264 compression when using in US TV system need to set to NTSC Highly improves video quality for live recording and network viewing Graphics amp Windows OSD interface Lower bit rate required for fastest network transfer VGA and RCA video outputs 1 RCA audio input and 1 RCA audio output Two USB interface USB2 0 for data backup USB1 1 for mouse operation Supports SATA HDD up to 2TB Password sensitive secure operation up to 8 users Allows up to 8 remote viewers at once Auto Data Rollover Recording Optimized four channel simultaneously playback Support remote live view parameter setting and copy playback video via network Cell phone remote viewing Data backup via USB port Motion detection USB mouse and Remote control DVR Specifications System Alarm Picture and Storage Network and Monitoring Backup mode Software upgrade Power Voltage input Dimensions and Weight SPECIFICATIONS Device Parameter Specification Multi language to choose from Language English Spanish Chinese Dutch French Turkish Russian Polish Hungarian Danish Italian Czech Portuguese Graphic menu OSD Menu 8ch composite video input
30. ontrol in the options menu in internet explorer 12 Question There is no picture or picture is not clear when you preview the recording or playback the recording via IE Answer Restart browser and log back in to the DVR Restart the DVR by going to Tools in the main menu then click on System Mng and click on Restart DVR 13 Question The mouse is not detected or not working properly Answer Mouse is defective or broken Mouse is plugged in the wrong port Make sure the mouse is plugged in the USB mouse port see page 5 14 Question No picture on selected channels Camera not displaying picture when there s no light the color of the picture looks weird Answer Camera cable is loose or disconnected Camera power cable not connected or defective Night vision color on a CCD camera is different than a normal camera 15 Question A humming sound and vibration coming from the system Answer This is normal the humming and vibration is coming from cooling fan or the system 16 Question Cannot login system when trying to remote view IE browser stuck at loading or error message on the screen Answer lt gt Check and make sure all the network settings on the DVR including the DDNS setting if you are using non static IP Also check you domain registration to make sure it s not expired 15 PACKAGE CONTENT DVR Power supply HDD SATA Cable 1111 LIL TL casce Er 3 9000 0000
31. orner of the screen Time Adjust Click to enter time adjust screen To change the time and date settings Simply click on the value that you want to change and use the on screen keypad to enter the desired value and click X on the keypad to close the keypad Repeat steps for the Year Month Day Hour Minutes Seconds Click Position To adjust the time to your desired area position Click OK when finish to save the time and return to the BASIC main screen click OK to exit to the Main Menu and click EXIT to exit out of the main menu Click Yes to save and exit the setup NTP Network Time Protocol is used to synchronize the time of a computer client or server to another server or reference time source Type in the desired NTP server and click on Active input the Interval time from O to 999mins DST select the appropriate time zone in your area for example Pacific Standard Time is 8 Then select what hour the time will change Audio Setting Click to adjust the input output of the audio 6 OPERATION continued LIVE Lets you customize camera names and setup Motion Detection e MN C a he Cave M Ll Hai Pebenap bimi ini kiak Dieta tiene Shieh H aren Estaci n Camera name number To change camera name Select which channel you want to change click on the box with O1 to bring up the number pad click the box again to bring up the
Download Pdf Manuals
Related Search