USER MANUAL
Contents
1. e Do not attach non computer related items such as medical equipment life support equipment microwave ovens or vacuum cleaners to UPS To reduce the risk of overheating the UPS do not cover the UPS cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces Unplug the UPS prior to cleaning and do not use liquid or spray detergent Do not dispose of battery or batteries in a fire The battery may explode Do not open or mutilate the battery or batteries Released electrolyte is harmful to the skin and eyes It may be toxic A battery can present a risk of electrical shock and high short circuit current The following precautions should be observed when working on batteries 1 Remove watches rings or other metal objects from the hand Use tools with insulated handles Wear rubber gloves and boots Do not lay tools or metal parts on the top of batteries Disconnect charging source prior to connecting or disconnecting batteries terminal Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions Keep unauthorized personnel away from batteries When replacing batteries replace with the same number of the sealed lead acid batteries This pluggable type A equipment with battery already installed by the supplier is operator installable and may be operated by laymen2. adequate airflow around the unit and is free from excessive dust corrosive fumes and conductive contaminants Do not operate your UPS in an environment where the ambient temperature or humidity is high On the other hand place the UPS unit away from monitor at least 20cm to avoid interference 3 Charging This unit is shipped from the factory with its internal battery fully charged However some energy may be lost during shipping so the battery should be recharged before using it Plug the unit into an appropriate power supply and allow the UPS to charge fully by leaving it plugged in for 8 hours 4 Computer Connection into each of the power Connect one computer related device receptacles supplied on the back of the UPS maximum of three devices 5 Modem Phoneline Connection Plug incoming internet line into the In socket at the back of the UPS Use one more Internet line cable and plug one end of the Internet line cable to the Out socket at the back of the UPS Plug the other end to the modem input socket as shown Incoming Dy eia Internetling SA e Ga d NI d d 9 D 6 Serial Cable Connection To allow for unattended system shutdown for your operating system connect the serial cable as per diagram below Monitor Computer 7 Turn On Off To turn on the UPS unit press the power switch lightly To turn o
3. During the installation of this equipment it should be assured that the sum of the leakage currents of the UPS and the connected loads does not exceed 3 5mA The mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily accessible 2 3 4 5 System Description Front Panel 1 LCD Back Light 2 Power ON OFF Switch Back Panel 1 Communication Port Option 4 AC Input 2 Modem Phone Line Surge Protection 5 FUSE 3 AC Output 6 BREAKER 110 120V Installation and Operation Installing the UPS is as easy as following the steps shown Be aware of the Power Switch must be kept in the ON position otherwise the UPS will be disabled and your equipment will not be protected during a power failure 1 Inspection Remove the UPS from its packaging and inspect it for damage that may have occurred during shipping If any damage is discovered repack the unit and return it to the place of purchase 2 Placement Install the UPS unit in any protected environment that provides
4. MENT Environment Less than 40dB SmartRS 232 Windows family Sun Solaris IBM Aix Compaq True64 optional UnixWare FreeBSD HP UX Linux and MAC INTERFACE For Windows family Mac
5. USER MANUAL Vesta Pro 600 800 VAC e EZEZ r t Uninterruptible Power System IMPORTANT SAFETY INSTRUCTIONS SAVE THESE I NSTRUCTI ONS This manual contains important instructions for models Vesta Pro 600 SOOVAC that should be followed during installation and maintenance of the UPS and batteries Safety CAUTION e This UPS utilizes voltages that may be hazardous Do not attempt to disassemble the unit The unit contains no user serviceable parts Only factory service personnel may perform repairs e Internal battery voltage is 12 06 Sealed lead acid 6 cells battery e Connection to any other type of receptacle other than a two pole three wire grounding receptacle may result in s shock hazard as well as violate local electrical codes e In the event of an emergency turn the power switch to the off position on and disconnect the power cord form the AC power supply to properly disable the UPS 6 Do not allow any liquids or any foreign object to enter the UPS Do not place beverages or any other liquid containing vessels on or near the unit 6 This unit intended for installation in a controlled environment temperature controlled indoor area free of conductive contaminants Avoid installing the UPS in locations where there is standing or running water or excessive humidity Do not plug the UPS input into its own output e Do not attach a power strip or surge suppressor to the UPS
6. ff the UPS unit press the power switch again When swith ON The LCD lighting 8 LCD Display Specification When LCD start to work it will display all information for 3s INPUT BATTERY Unit VDC Hz VAC OUTPUT LOAD FAULT Unit Hz VAC LOAD LEVEL BATTERY CAPACITY LINE MODE AVR BACKUP MODE a When in normal mode it will display as below b When in AVR mode it will display as below And the mark Ge will flicker every 47 c When in battery mode it will display as below And the mark EO will flicker every 7 Note If I P V lt 20V gt input voltage will display 000 d When in off charging mode it will display as below Note the output voltage always 18 displayed as 000 in off charging mode e When in fault mode it will display as below FAULT character and the reason of fault only 6 Load level definition Load LEVEL Load bar Indication SO parr 75 100 7 Battery capacity definition Battery LEVEL Battery bar Indication Battery voltage 11V 3 coo 11V lt Battery voltage lt 11 5V 200 2000 8 When over load the mark 5 will flicker every 1second 9 When battery low the mark E will flicker every 1second Software Installation WinPower WinPower is a brand new UPS monitoring software which provides user friendly interface to monitor and control your UPS This unique software provides safely auto shutdown for multi computer
7. or elecerity the Input Power switch is not cord pressed Overload of the UPS Verify that the load matches the UPS capability specified in the specs load low more 3 Battery defect due to 3 Replace with the same type high temperature of battery operation environment or improper operation to battery lost between UPS installed well software and computer d Cable is not properly 2 Check the USB cable is connected firmly connected to COM1 COM2 of the computer and confirm the setting again LCD display fuse properly Specification CAPACI TY VA W 600 360 800 480 Voltage Range 89 145VAC 50Hz 60Hz BTT 120VAC 110VAC ene Stepped Sine wave 12V 7Ah 12V 9Ah Back up Time SEY One PC 15 Monitor 20 mins 29 mins Recharge Time 6 hours to 90 at normal mode after complete discharge TRANSFER l TIME Typical 2 6ms typical 10 ms max The LCD will always turn on when UPS work dE LCD Display Models Including in off charging mode and fault mode Backup Mode Sounding every 10 seconds Sounding every 1 second AUDI BLE sounding every 0 5 seconds ALARM Battery replace Sounding every 2 seconds Buck boost with Sounding every 0 5sec after 25min gt 70 SPS load And fault after 30 mins PROTECTION Full Protection Discharge Overcharge short circuit and Overload Protection PHYSICAL Hua 330 100 140 mm Net Weight 13 2lb 6kg 14 3 lb 6 5Kg prae 0 40 C 0 90 Relative Humidity non condensing ENVIRON
8. systems while power failure With this software users can monitor and control any UPS on the same LAN no matter how far from the UPSs ETT TT TT E TE EE TT RI ee gea Winpower Manager BAOCNWHP3004167 Read only System Logs Device Tools Monitor SNMP Preference Language Help Fa HO Zu d Root Normal GRA Model LINE INT Com Port USB 8 BAOCNWHP3 ep USB E XD BAOCNWHP 10 9 BAOCNWHP1 gdy WAN Pla SNMP 231 04 Parea 49 5Hz d 231 04 Noe LILURA LOAD Charger iia Battery voltage fi 3 6 25 0 C UPS Temp 2013 06 29 09 45 35 Communication with UPS normal 4 D 2013 06 29 09 45 44 Output Output off Installation procedure 1 Goto the website http www ups software download com index htm 2 Choose the operation system you need and follow the instruction described on the website to download the software 3 When downloading all required files from the internet enter the serial No 511C1 01220 0100 478DF2A to install the software Trouble Shooting Use the table below to solve minor UPS installation or operation problems If any abnormal situations occur that are not listed above please call service people immediately Possible Cause No LCD display on 1 Missing battery 1 Charge battery up to 8 the front panel hours 2 Battery defect 2 Replace with the same type of battery 3 When the Input cord 3 Press the power switch isn t electvified and again
Download Pdf Manuals
Related Search