Home
Quick Start Guide
Contents
1. INSTALLING IN A CHASSIS ccceccccccecceeececccececcceaeececcaeeceeceeaeeceeeaeeseeeass 9 SPECIFICATIONS docccsciccssocdaiceebiescSssvaededscccoacceoascsdececbaagceeseedeacesecuccuoeacdsseectescccecdededs 10 4 User s Manual Gigabit Ethernet Media Converter Introduction The Gigabit Ethernet Media Converter provides one channel for media conversion between 10 100 1000Base TX to 1000Base SX LX BX with link fault pass through function It can be used as a stand alone device or with a standard 19 chassis as shown below Product Overview 10 100 1000BASE 1000BASE PWR LNKF LNKC oro ose FDX i G GE TXIRX LFPT A 100 Figure 1 Gigabit Ethernet Media Converter with link fault pass through function lt NOTE gt The chassis is to be ordered separately User s Manual 5 Gigabit Ethernet Media Converter Product Features Complies with IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T and IEEE802 3z 1000Base SX LX Supports IEEE802 3x Flow control Flow control for Full duplex and Back pressure for Half duplex DIP switch configuration for Link Fault Pass Through Gigabit transmission supports 9K Bytes jumbo frame 1000Mbps Full duplex 10 100Mbps Full Half duplex Auto Negotiation Auto MDI MDIX Full wire speed forwarding rate Operating voltage and
2. Gigabit Ethernet Media Converter Quick Start Guide This quick start guide describes how to install and use the Gigabit Ethernet media converter The converter introduced here provides one channel media conversion solution Physical Description Product Overview 10 100 1000BASE 1000BASE P ee O loto OO ovo 000000 TX RX 9909 O DC12V O This Gigabit Ethernet media converter is a plug and play device Connect the supplied AC to DC power adaptor to the receptacle on the rear panel of the Gigabit Ethernet media converter and then attach the plug into a standard AC outlet DIP Switch E Disable LFPT Enable LFPT Link Fault Pass Through function Enable Auto Negotiation for TX port ate Force modeto TA MN TX port Force mode TX port Force mode Full duplex Half duplex pe TX port Force mode 5 Functionreseved reserved Function reserved reserved pme o Function reserved Function reserved mme ooo lt Note gt Power must be off on after re setting LFPT function The 10 100 1000Base TX and 1000Base SX LX BX Connectors The 10 100 1000Base TX Connection Pn Label The following lists the pinouts of 10 100 1000Base TX port gt A a LAA The 1000Base SX LX Connection The Tx transmit port of device is connected to the Rx receive port of device Il and the Rx receive port of device to the Tx transmit port of R TN device Il User s Manual 1 Gigabit Ethernet Media Convert
3. Max current consumption 0 23A 12VDC Power consumption 2 76W Max Power Supply 12VDC external universal PSU OC to50 C 32 F to 122 F operating temperature range Aluminum case Supports Wall Mounting installation or use with media converter chassis system DIP Switch woo p LFPT Disable LFPT Enable LFPT Link Fault Pass Through function Enable Auto Negotiation for TX port atau Force mode for TX Function reserved Function reserved Function reserved Function reserved lt Note gt Power must be off on after re setting LFPT function i TX port Force mode F TX port Force mode Full duplex Half duplex AN TX port Force mode 6 User s Manual Gigabit Ethernet Media Converter Packing List When you unpack this product package you will find the items listed below Please inspect the contents and report any apparent damage or missing items immediately to your authorized reseller e The Media Converter e User s Manual e AC to DC Power Adaptor User s Manual 7 Gigabit Ethernet Media Converter One Channel Media Converter Physical Ports Gigabit Ethernet Media Converter This converter provides one TX port and one 1000Base SX LX BX port For the 1000Base SX LX BX port it provides options of multi mode single mode or WDM multi mode single mode fiber For the TX port it uses RJ 45 connector and supports auto MDIX for uplink purpose Port Status LEDs The LED indicators give you instant feedback o
4. e equipment receives adequate ventilation Do not block the ventilation holes of the equipment The power outlet should be within 1 8 meters of the product Connecting to Power This Converter is a plug and play device Connect the supplied AC to DC power adapter to the receptacle at the back of the converter Attach the plug into a standard AC outlet Installing in a Chassis The Converter is designed to fit into any of the expansion slots on a rackmount chassis Unscrew the carrier from the desired expansion slot on the chassis Fit the converter onto the carrier When the converter is completely seated onto the carrier insert the carrier to the guide rails of the expansion slot Carefully slide in the carrier until it is fully and firmly fit the chassis Fasten the carrier to the chassis by the screws lt NOTE gt Never insert any converter into the chassis directly without using the supplied caniers The caniers allow secure and consistent placement of the converters into the chassis backplane without causing any damage User s Manual 9 Specifications Applicable Standards IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T IEEE802 3z 1000Base SX LX Fixed Ports 10 100 1000Base TX to 1 TX port 1000Base SX LX BX 1 FX port Speed 10Base T 10 20Mbps for half full duplex 100Base TX 100 200Mbps for half full duplex 1000Base T 2000Mbps for full duplex 1000Base SX LX BX 2000Mbps for full dupl
5. er The WDM 1000Base BX Connection TX RX The fiber port pinouts Only one optical fiber is required to transmit and receive data The Port Status LEDs 10 100 1000BASE 1000BASE PWR LNKF LNKC ae OOO FDX G GE TX RX LFPT A 100 Indication Power off LFPT function enabled LFPT function disabled prc Sea Copper port A valid network connection established LNKC LNKC stands for LINK Copper f y No connection Copper Port Stead Green Connection at the speed of 1000Mbps 10 100 1000 Y Amber Connection at the speed of 100Mbps t Mbps Connection at the speed of 10Mbps Stead Fiber port A valid network connection established LNKF Y LNKF stands for LINK Fiber No connection Full duplex mode FDX nipay FDX stands for Full duplex Half duplex mode Functional Description Complies with IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T and IEEE802 3z 1000Base SX LX Supports IEEE802 3x Flow control Flow control for Full duplex and Back pressure for Half duplex DIP switch configuration for Link Fault Pass Through Gigabit transmission supports 9K Bytes jumbo frame 1000Mbps Full duplex 10 100Mbps Full Half duplex Auto Negotiation Auto MDI MDIX Full wire speed forwarding rate Operating voltage and Max current consumption 0 23A 12VDC Power consumption 2 76W Max Power Supply 12VDC external universal PSU e 0C to50C 32 F to 122 F operating temperat
6. es one channel media conversion solution 10 100 1000Base TX to 1000Base SX LX BX with link fault pass through function The Gigabit Ethernet Media Converter fully complies with IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T and IEEE802 3z 1000Base SX LX Ethernet standards In this manual you will find Product overview Features on the media converter Illustrative LED functions Installation instructions Specifications User s Manual 3 Gigabit Ethernet Media Converter Table of Contents QUICK START GUIDES 00 cicids 1 PHYSICAL DESCRIPTION 0cceececcecceccececeeceececeececeecesaececeeceeaesecueeeees 1 FUNCTIONAL DESCRIPTION 2 ccccecececceceeeeceecccaeccecceeceececeaeeceeeaeeneeeaees 2 FEC STATEMENT Ti A n a 3 TRADEMARKS diia cito 3 PREFACE Li aaa 3 TABLE OF CONTENTS a iii 4 INTRODUCTION ii iia 5 PRODUCT OVERVIEW ccccecceeececceceeeccecceeeceeceeaeececeaeeceeeueeaeeseeeaeeneeeaees 5 PRODUC AR EAM RES aaa aaae renee 6 PACKING LIS Tails 7 ONE CHANNEL MEDIA CONVERTER ccccccococonocononononononononononononononoconononoconocenocononos 8 PHYSIGALIROR TS do da a do ad ed a A 8 PORT STATUS LEDS 70 00 22 ccccceccecccecceeceeccecceeeeeccesceecceeceeceeseeeceeeeeseeeeees 8 INSTALLATION carioca ciclos bancadas 9 SELECTING A SITE FOR THE EQUIPMENT 2 0sccecceeececcecceecceceeecaeececeaes 9 CONNECTING TO POWER 0 ccecceccceececcceceeceeceeeceeceecaeeceecaeeteceuecaeeseeeaes 9
7. ex Forwarding rate 14 880pps for 10Mbps 148 810pps for 100Mbps 1 488 100pps for 1000Mbps LED Indicators PWR LFPT LNKC Copper Port Speed LNKF FDX Dimensions 80 3mm W x 109 2mm D x 23 8mm H 3 16 W x 4 3 D x 0 94 H 1509 0 33lb 1509 0 33lb SS y O Power External power adaptor 0 23A 12VDC Emissions FCC part 15 Class A CE Mark Class A 10 User s Manual
8. n status of the converter ETE PWR 10 100 1000BASE LNKF LNKC lovolese ovo DOS FDX G GE TXIRX LFPT A 100 SAS o Pua O DC12V Figure 2 Gigabit Ethernet Media Converter with link fault pass through function Indication Poneto Power off LEPT Stead Copper port A valid network connection established LNKC Y LNKC stands for LINK Copper Copper Port Giga Green Connection at the speed of 1000Mbps 10 100 1000 Y Amber Connection at the speed of 100Mbps Mbps Connection at the speed of 10Mbps Stead Fiber port A valid network connection established LNKF Y LNKF stands for LINK Fiber Full duplex mode Steady FDX stands for Full duplex Half duplex mode 8 User s Manual Gigabit Ethernet Media Converter Installation This chapter gives step by step installation instructions for the Converter Selecting a Site for the Equipment As with any electric device you should place the equipment where it will not be subjected to extreme temperatures humidity or electromagnetic interference Specifically the site you select should meet the following requirements o The ambient temperature should be between 32 and 122 degrees Fahrenheit 0 to 50 degrees Celsius The relative humidity should be less than 95 percent non condensing Surrounding electrical devices should not exceed the electromagnetic field RFC standards for IEC 801 3 Level 2 8V M field strength Make sure that th
9. ure range Aluminum case e Supports Wall Mounting installation or use with media converter chassis system 2 User s Manual Gigabit Ethernet Media Converter FCC Statement The FCC Federal Communications Commission restricts the amount of radio frequency emission and radiation coming from computer equipment The equipment introduced in this manual has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the interference at his her own expense Any changes or modifications not expressly approved by the manufacture would void the user s authority to operate the equipment Trademarks Product names mentioned in this manual may be trademarks or registered trademarks of those products All trademarks or brand names mentioned are properties of their respective companies Preface This manual describes how to install and use the Gigabit Ethernet Media Converter The Converter introduced here provid
Download Pdf Manuals
Related Search
Related Contents
RFID_Pr_WebLogic_JAVA_user guide_SAI_090803 Denon POA-3012CI User's Manual 取扱説明書 - Brother ゼルダの伝説 時のオカリナ 3D Catalogue E-Cigarettes - E-Vaporisateurs M3T-CC32R V.4.30 User`s Manual ラボトルクドライバ使用説明書 2801, 2802, 2803 User Manual Vtech 5867 Cordless Phone Marmitek Invisible Control A/V Equipment User's Manual Copyright © All rights reserved.