iVision 3D User Manual for Barco
Contents
1. POWER indicator A green light will appear when the power switch is on and it indicate the connection with projector is under normal condition Otherwise please check if the DB15 15 is cable being connected probably 8 iVision passive 3D system V901A user manual When the green power indicator is sparkling please switch off the 3D system and reset the projector channel to 2D Then switch on the 3D system again e Synchronization signal INPUT connection port The attached DB15 15 cable is to connect with the projector for 3D signal system power supply The 15PIN female end is to be connected to the INPUT port on the 3D system control box The other male end is to be connected to the projectors 3D Interface e SYNC synchronization indictor Green SYNC light indicate the 3D signal is detected and ready for 3D movie showing When the light is out no 3D signal is being detected Please check if the DB15 15 cable is being connected correctly and make sure the projector is set up probably Synchronization OUTPUT connection port The DB9 9 cable is to connect between the Len and the control box for synchronization with the whole system iVision passive 3D system V901A user manual 5 Installation of the passive 3D system 5 1 Use M10 50 screw to fix the base plate of control box on the Barco projector Fig 5 1 There are already the correspondent hole on the base plate to match with different Barco series The2. letter S C B on the base plate is showing different hole position on different Barco series S S series C C series B B series N o o Fig 5 1 Base plate of the control box X Note 1 The screw must be firmly fixed to avoid the system damaged X Note 2 This is the cable fixing position iVision passive 3D system V901A user manual alignment hole alignment hole Fig 5 1 1 Barco S series installation position alignment hole Fig 5 1 2 Barco C series installation position alignment hole alignment hole alignment hole Fig 5 1 3 Barco B series installation position 11 iVision passive 3D system V901A user manual After fixing the base plate fix the DB9 cable to the correspondent position x Please also be noted the male female direction Fig 5 1 4 DB9 cable 5 2 Apply 4 x M5 12 screw to fix the control box on the base plate as Fig 5 2 1 then apply 2 x M6 16 screw to fix the Len fixture stand on the control box cover as Fig 5 2 2 All screw must be firmly fixed M5 12 Screw iVision passive 3D system V901A user manual M6 16 Screw si Fig 5 2 2 5 3 Apply 1 x M8 70 screw to fix the Len and the connection pole as Fig 5 3 1 then apply 3 x M6 10 screw to attach the Len to the control box as Fig 5 3 2 iVision passive 3D system V901A user manual Fig 5 3 2 5 4 As Fig 5 4 the DB15 15 cable is to be connected to the port INPUT on the con
3. 1A user manual 4 1 The Len WESTON Fig 4 2 The Len The outer dimensions of the Len 274 0mm 225 0mm 29 8mm and net weight is 1 5kg This is the major and important optical device of the V9O1A 3D system No crash is allowed during the installation Handle with care iVision passive 3D system V901A user manual 4 2 Automatic rack and system control box Fig 4 3 Automatic and system control box 4 1 1 The automatic and system control box is the device for 2D 3D interchange and control module for synchronization of 3D signal 4 1 2 The DB9 9 cable will be connected between the 3D system Len and the system control box While 3D signal being detected the Len will automatically move in front of the pre set position of the projector While 2D movie is detected the Len will move out to the standby position 41 3 During installation please handle with care to prevent the mechanical parts being crashed to the projector and projector Len iVision passive 3D system V901A user manual 4 1 4 Integrated and flexible mechanical design facilitates a user friendly Len position adjustment and system mounting and installation on projectors ON OFF POWER INPUT SYNC OUTPUT Fig 4 4 Connection panel e Power Switch Switch on the system for electricity supply Note Before switch on the 3D system please connect the DB15 5 cable to the projectors 3D connection port and switch on the projector e
4. D control box Please switch off the 3D system before removing any cable Please switch off the 3D system and remove all the cable before transportation or cleaning the 3D system e Please dry your hand before touching the 3D system End
5. ge 1 The system will automatically detect 2D 3D signal While it is a 3D movie the Len will move to the projector Len automatically and ready for 3D projection While it is anon 3D movie it will be back to the standby position It is designed to operate in coordination with any TMS system iVision passive 3D system V901A user manual e Easy to maintain The Len is easy to clean and maintain 2 System feature e Electrical data Power source Nil Synchronized signal input 3D interface 15 pin Wattage less than 12w e Optical feature Light efficiency 16 1 Contrast 100 1 Ghost shadow Less than 2 Response time Less than 150us Frame rate Support 60frames second 3 Projectors and 3D glasses e Polarization 3D glasses iVision approved 3D glasses e Projectors The iVision 3D system is applicable to all Barco Christie and NEC DCI projectors including 4K projectors 4 System Structure The 3D system will include the following compartments iVision passive 3D system V901A user manual e The Len e Automatic frame and rack e DB9 9 cable DB15 15 cable Fig 4 1 Passive 3D system Barco projectors It is easy mounted and fixed on the pre drilled holes on the top of Barco C S and B series projectors Christie and NEC projector it will be mounted with the tailor made frame and rack for each specific model Details will be provided separately to suit different projector models iVision passive 3D system V90
6. le P VISION iVision passive polarization 3D system V9OLA User Manual For All Barco models iVision Global Ltd Flat 337 3 F South China C S Bldg 13 17 Wah Sing Street Kwai Chung Kowloon Hong Kong Malaysia RT I Vision Sdn Bhd 324 Jalan Nilam 12 Taman Jayamas 70200 Seremban Negeri Sembilan Malaysia Thailand GT Vision Thailand Co Ltd 234 47 Moo 6 Suksawad Rd Naiklongbangplakod Prasamutjadee Samutprakarn 10290 Thailand iVision passive 3D system V901A user manual Content 1 System Introduction 3 2 System feature 4 3 Projector amp 3D glasses 4 4 System structure 4 9 5 Installation 10 15 6 Dark Time Adjustment and Output Reference Delay setting 16 7 Optical Alignment 16 8 Others 17 18 iVision passive 3D system V901A user manual 1 System introduction iVision passive 3D system V901A is the passive polarization 3D system for projectors The system is user friendly and easy to install with projectors The sensitive and fully automatic mechanism offers quick and accurate 2D 3D movies interchange e Easy to install Just using the attached frame and screw can be fixed on projectors e Easy to connect The connection between the 3D system and projector is to be done by only 2 cables e 2D 3D interchan
7. tical alignment iVision passive 3D system V901A user manual 8 Others 8 1 Installation reminder e The distance between the 3D Len and the Projector Len should not be less than 10cm e The 3D Len logo should be facing the projector Len e The projection light beam should be control on the center of the 3D Len The projection beam should not be projected on the Len metal frame with at least 5mm 10mm as non projection area from each side of the 3D Len s metal frame e The Len projection film must be taken out during moving showing e Silver screen with 2 4 gain or above will offer the best 3D imagine 8 2 Daily maintenance e The 3D Len should be cleaned with alcoholic cloth Note Alcoholic in liquid form MUST not be applied e Operation environment Temperature 10 C 50C Relative Humidity lt 60 e Please don t apply sharp and hard object on the Len surface e All 3D glasses should be cleaned by alcoholic cloth It 17 iVision passive 3D system V901A user manual should not use water to clean 8 3 Transportation note The passive 3D system must not be throw and cast during transportation The Len is a fragile part It must be stored separately during transportation 8 4 Safety reminder Please don t apply sharp and hard object on the Len surface to avoid damage of the Len Don t place the Len near the steam and mist area Don t bend the cable and plug in abnormal way and don t put heavy object on the 3
8. trol box and the projector 3D 14 iVision passive 3D system V901A user manual Interface port The cable must be firmly fixed to avoid improper contact The DB9 9 9 pin female cable is to be connected to the DB9 port on the Len and the control box male The cable must be firmly fixed to avoid improper contact connect to connect to Projector the Len DB9 3D port port Fig 5 4 cable connection 5 5 Criteria for Len position e The Len of the 3D system is to be positioned to the center of the projector Len for 3D movie e The Len of the 3D system should be completely moved away from the projector Len for 2D movie showing e There should be no crash or touch of 3D Len and the projector Len during the automatic movement of 2D 3D interchange iVision passive 3D system V901A user manual 6 Dark Time Adjustment and Output Reference Delay setting In the projector The Dark Time Adjustment 1500 220 Output Reference Delay 7 Optical alignment e Switch on the projector and let the 3D Len move toward the center of projector Len e Upload and apply the projector alignment program and slightly adjust the 3D Len position to align the sign perfectly overlap coincide and match together e Screw A For sign alignment e Screw B For adjustment of the 3D Len to make the beam perpendicular to the silver screen fam V2 ae nia TA a Ni mi NG ib Ge screwA screw B Fig 6 1 Op
Download Pdf Manuals
Related Search