User Manual PCIE-1760
Contents
1. 19 Specifications iii asa 20 SA 20 Block Diagram 1 12 111 23 PGIE 1760 sinistre nine al 24 vii PCIE 1760 User Manual PCIE 1760 User Manual viii Chapter 1 Overview 1 1 Introduction The Advantech PCIE 1760 is a 8 channel isolated digital input and 8 channel relay output card for the PCI Express bus The PCIE 1760 s isolated digital input channels are ideal for digital input in noisy environments or with floating potentials Each isolated digital input supports both dry contact and wet contact designated by jumper settings so that it can easily interface with other devices PCIE 1760 relays can serve as ON OFF control devices or small power switches For easy monitoring each relay is equipped with one green LED to reflect its ON OFF status Moreover PCIE 1760 also offers counter input and PWM input output channels The following sections of this chapter will provide further information about features installation guide together with some brief information on software and accessories for the PCIE 1760 card 1 2 Features PCIE 1760 8 opto isolated digital input channels 8 relay actuator output channels 2 counter input channels and 2 opto isolated PWM output channels High voltage isolation on isolated I O channels 2 500 Vpc LED indicators to show activated relays Jumper selectable dry contact or wet contact for digital input channels D type connect2. AE C le PCIE 1760 User Manual 18 Appendix A Specifications A 1 Specifications A 1 1 PCIE 1760 Isolated Digital Input Digital Input Channels Input Voltage 8 Logic 0 O 3 Voc Logic 1 10 30 Voc Input Current 30 Voc 9 73 mA Input Resistance B 2KQ 1W Interrupt Capable Channels 1 IDIO Opto Isolator Response 60 us Counter Input Channels 2 Sei Input Frequency up to 1 kHz Counter Input Internal clock up to 20 MHz Mr effective high input period 1 us 255 us unit 1 us Digital Input Filter effective low input period 1 us 255 ps unit 1 us Over Voltage Protection 70 Voc ESD Protection 2000 Vic Isolation Protection 2500 Voc Note Counter input channel shares some pinouts from isolated digital channels Relay Output Relay Output Channels 8 Channel 0 1 single pole double throw SPDT Form C Relay Type Channel 2 7 single pole single throw SPST Channel 0 1 Normal Open NO and Normal Close NC Output type Channel 2 7 Normal Open NO or Normal Close NC selectable by jumper Contact Rating 125 Vac 0 5 A 30 Voc 1 A Contact Resistance lt 100 MQ initially Coil to contacts 1500 Vrms Disiecuie Strengih Between open contacts 1000 Vrms Operate Time 5 ms maximum Release Time 3 5 ms maximum Electrical 200 000 0 5 A 120
3. PWMn n 0 1 Isolated or TTL digital output for PWM Rn OUT n 207 Normally Open Closed pin of Relay output Rn NO n 01 Normally Open pin of Relay output Rn NC n 0 1 Normally Close pin of Relay output Rn COM n 0 7 Common pin of Relay output GATEn n 0 1 Counter n gate input GATEn n 0 1 Counter n gate input CLKn n 0 1 Counter n clock input CLKn n 0 1 Counter n clock input PCIE 1760 User Manual CN6 IGND T IDI 7 2 21 IDI 6 GATE 1 3 22 IDI 5 4 23 IDI 4 CLK 1 5 24 IDI 3 6 25 IDI 2 GATE 0 7 26 IDI 1 8 27 IDI 0 CLK 0 9 28 PWMO 10 29 R7_OUT 11 30 R6_OUT 12 31 R5_OUT 13 32 R7_COM 14 33 R6_COM 15 34 R5_COM 16 35 R4_COM 17 36 R3_COM 18 37 R2_COM la 16 IDI 7 IDI 6 GATE 1 IDI 5 IDI 4 CLK 1 IDI 3 IDI 2 GATE 0 IDI 1 IDI 0 CLK 0 PWM1 R4_OUT R3_OUT R2_OUT R1_NO R1_NC R1_COM RO_NO RO_NC RO_COM Isolated Digital Input Each of the 8 isolated digital input channels accepts either dry contact or 10 30 Vic wet contact inputs as determined by the corresponding jumper settings see Table 3 1 Dry contact capability allows an input channel to respond to changes in an external circuit e g the closing of a switch in the external circuit when no voltage is present in the external circuit Figure 3 2 shows the internal and external circuitry with both wet and dry contact components connected as an input source for one of th
4. User Manual PCIE 1760 8 ch Isolated Digital Input amp 8 ch Relay Output PCI Express Card AD ANTECH eAutomation Copyright The documentation and the software included with this product are copyrighted 2013 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Product Warranty 2 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech a
5. JP11 1 2 pin short Set relay channel 5 as Normal Open default 2 3 pin short Set relay channel 5 as Normal Close JP12 1 2 pin short Set relay channel 6 as Normal Open default 2 3 pin short Set relay channel 6 as Normal Close JP13 JP14 JP15 1 2 pin short Set relay channel 7 as Normal Open default 2 3 pin short 1 2 pin short Set relay channel 7 as Normal Close Output channels will keep last status after system resets 2 3 pin short 1 2 pin short Output channels will set their values to Low after system resets default Set PWM output channel 0 voltage level to isolated DO 5 40 Vpc 2 3 pin short Set PWM output channel 0 voltage level to 5V TTL compatible default JP16 1 2 pin short Set PWM output channel 1 voltage level to isolated DO 5 40 Vpc 2 3 pin short Set PWM output channel 1 voltage level to 5V TTL compatible default Table 3 2 Board ID setting SW1 1D3 1D2 1D1 IDO Board ID 1 1 1 1 0 1 1 1 0 1 1 1 0 1 2 1 1 0 0 3 1 0 1 1 4 1 0 1 0 5 1 0 0 1 6 1 0 0 0 7 0 1 1 1 8 0 1 1 0 9 0 1 0 1 10 0 1 0 0 11 0 0 1 1 12 0 0 1 0 13 0 0 0 1 14 0 0 0 0 15 Note On 1 Off 0 15 PCIE 1760 User Manual 3 3 Signal Connections PCIE 1760 Pin Assignments Description of pin use IDIn n 0 7 Isolated digital input IDIn n 0 7 Isolated digital input
6. always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC is on Disconnect power before making any configuration changes The sudden rush of power as you connect a jumper or install a card may damage sensitive elec tronic components V PCIE 1760 User Manual PCIE 1760 User Manual vi Contents Chapter 1 dd a Oo O1 B ND Chapter 2 Chapter 3 3 1 3 2 3 3 Appendix A A 1 Appendix B B 1 OVECIVICW ccccccececccccccccscecenecencacacscscscsceee 1 Introduction isc acia iia 2 Features iii ati ib a aiii 2 Applications eri ii DER Rae a ad 7 Installation Guide ana 7 Software Overview i 7 ACCESSOS ui iii tds 8 Instala ici id iii tddi 10 Unpacking au 2 2 ii ao 10 DriVer Installation u 0 u nen ran anna 11 Hardware Installati n u 11 Figure 2 1 Device Manager nn 12 Signal Connections 19 OVOIVIGW icis a devas vanddundarees indica adaga iii 14 Switch and Jumper Settings raras 14 Figure 3 1 Card Connector Jumper and Switches 14 Table 3 1 Summary of Jumper Settings nn 14 Table 3 2 Board ID setting SW1 nennen 15 signal Connects civic een 16 Figure 3 2 Isolated DI Connection 17 Figure 3 3 Relay Output Connection nn 17 Specifications
7. is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna E Increase the separation between the equipment and receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help Technical Support and Assistance 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages iii PCIE 1760 User Manual Warnings Cautions and Notes Warning Warnings indicate conditions which if not observed can cause personal injury Caution Cautions are included to help you avoid damaging hardware or losing data e g A There is a danger of a new battery exploding if it is incorrectly installed Do not attempt to recharge force open or heat the battery Replace the battery only with the same or equivalent type recommended by t
8. Vac Lire Expectancy 500 000 1 0 A 30 Voc PCIE 1760 User Manual 20 PWM Output PWM Output Channels 2 PWM Output Type 5V TTL or Isolated DO selectable by jumper PWM Output Range TTL Logic 0 lt 0 8 Vic Logic 1 5 0 5 Vic PWM Output Current PWM Output Range Isolated DO Sink 0 5 A Source 2mA 5 40 Voc PWM Output Frequency up to 1 kHz Scaling Resolution 32 bits 50 ys for each step PWM High Period 100 us 232 1 x 50 ps deviation 60 us PWM Low Period 100 us 232 1 x 50 ps deviation 60 us Isolation Protection 2500 Voc General I O Connector Type 37 pin D Sub female Dimensions 167 7 mm x 100 mm 6 6 x 3 9 Typical 3 3 V 390 mA 12 V 30 mA Power Consumption Max 3 3 V 490 mA 12V 60 mA Operation 0 60 C 32 140 F refer to IEC 60068 2 1 2 Temperature S SA Storage 25 85 C 4 185 F Relative Humidity 5 95 RH non condensing refer to IEC 60068 2 3 Certification CE certified 21 PCIE 1760 User Manual PCIE 1760 User Manual 22 Appendix B Block Diagram B 1 PCIE 1760 Board ID Switch 2 ch PWM Output o ESA i 8 ch Relay Output e ab DB37 Connector PCIE Bus PCIE 1760 User Manual 24 25 PCIE 1760 User Manual AD ANTECH eAutomation www advantech com Please verify spe
9. and card installation Unpacking After receiving your PCIE 1760 package please inspect its contents first The pack age should contain the following items m PCIE 1760 card E Companion CD ROM m User s Manual The PCIE 1760 card harbors certain electronic components vulnerable to electro static discharge ESD ESD could easily damage the integrated circuits and certain components if preventive measures are not carefully paid attention to Before removing the card from the antistatic plastic bag you should take following precautions to ward off possible ESD damage Touch the metal part of your computer chassis with your hand to discharge static electricity accumulated on your body Or one can also use a grounding strap Touch the anti static bag to a metal part of your computer chassis before open ing the bag m Take hold of the card only by the metal bracket when removing it out of the bag After taking out the card first you should Inspect the card for any possible signs of external damage loose or damaged com ponents etc If the card is visibly damaged please notify our service department or our local sales representative immediately Avoid installing a damaged card into your system Also pay extra caution to the following aspects to ensure proper installation m Avoid physical contact with materials that could hold static electricity such as plastic vinyl and Styrofoam m Whenever you handle the card grasp
10. cifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies O Advantech Co Ltd 2013
11. co voo Nooo oco voo 123 123 123 123 123 123 Table 3 1 Summary of Jumper Settings Jumper No Operation Function Description JPO 1 2 pin short Set DI channel 0 as Dry Contact default 2 3 pin short Set DI channel O as Wet Contact JP 1 2 pin short Set DI channel 1 as Dry Contact default 2 3 pin short Set DI channel 1 as Wet Contact JP2 1 2 pin short Set DI channel 2 as Dry Contact default 2 3 pin short Set DI channel 2 as Wet Contact JP3 1 2 pin short Set DI channel 3 as Dry Contact default 2 3 pin short Set DI channel 3 as Wet Contact JP4 1 2 pin short Set DI channel 4 as Dry Contact default 2 3 pin short Set DI channel 4 as Wet Contact JP5 1 2 pin short Set DI channel 5 as Dry Contact default 2 3 pin short Set DI channel 5 as Wet Contact JPG 1 2 pin short Set DI channel 6 as Dry Contact default 2 3 pin short Set DI channel 6 as Wet Contact JP7 1 2 pin short Set DI channel 7 as Dry Contact default 2 3 pin short Set DI channel 7 as Wet Contact JP8 1 2 pin short Set relay channel 2 as Normal Open default 2 3 pin short Set relay channel 2 as Normal Close JP9 1 2 pin short Set relay channel 3 as Normal Open default 2 3 pin short Set relay channel 3 as Normal Close JP10 1 2 pin short Set relay channel 4 as Normal Open default 2 3 pin short Set relay channel 4 as Normal Close PCIE 1760 User Manual 14 Table 3 1 Summary of Jumper Settings
12. d by the user Interrupt Function Ensures Faster System Response The PCIE 1760 provides a Pattern Match interrupt function for the digital input channels It monitors the state of some or all of the input channels and compares it with a pre set pattern When the received state matches the pre set pattern PCIE 1760 will generate an interrupt signal to the system The Change of Input State interrupt function means PCIE 1760 monitors the state of the input channels When any input changes its state the card interrupts the system to handle this event Note For detailed specifications of the PCIE 1760 refer to Appendix A Spec E ifications PCIE 1760 User Manual 6 1 3 1 4 1 5 Applications Industrial ON OFF control Signal switching External relay driving Digital signal and contact status monitoring Industrial and lab automation Laboratory amp Education Installation Guide Before you install your PCIE 1760 card please make sure you have the following necessary components PCIE 1760 card PCIE 1760 User s Manual Advantech driver DAQNavi included in the CD ROM Wiring cable PCL 10137 option Wiring board ADAM 3937 option Personal computer or workstation with a PCI Express bus slot Some other optional components are also available for enhanced operation m Application software Advantech Navigator Utility offered by DAQNavi software After you get the necessary components and maybe some of
13. e PCIE 1760 s isolated digital input channels External Interval IVec Vcc Wet Dry Dry Contact Closed High Contact Open Low Wet Contact 10 30 VDC High i 0 3 VDC Low Figure 3 2 Isolated DI Connection Relay Output Of the total eight relays two relays Channel 0 and 1 are single pole double throw SPDT Form C and six relays Channel 2 to Channel 7 are single pole single throw SPST which can be set as either normally open NO or normally closed NC via jumper settings The following figure illustrates the structures and connections of the relay outputs JPn 6 NC NO NO Relay n n 0 1 Relay n n 2 7 Figure 3 3 Relay Output Connection 17 PCIE 1760 User Manual Isolated Digital Output Each of isolated output channels comes equipped with a MOSFET and a polyswitch for current protection for using with inductive loads If an external voltage 5 40 Vpc is applied to an isolated output channel the current will flow from the external voltage source to the card Please note that the current through each IDO channel should not exceed 500 mA Internal External PCIE 1760 Polyswitch IGND TTL Digital Output The two isolated output pins for PCIE 1760 can also be configured as TTL digital out put using JP15 and JP16 See Table 3 1 The following figure shows connections to exchange digital signals with other TTL devices Internal External TTL device
14. eyboards A Mice and other pointing devices E Monitors amp Network adapters gt Other devices 19 Ports COM amp LPT ID Processors Sound video and game controllers JM System devices Universal Serial Bus controllers Figure 2 1 Device Manager Note Ifyour card is properly installed you should see the device name of your N card listed on the Device Manager tab If you do see your device name E listed on it but marked with an exclamation sign it means your card has not been correctly installed In this case remove the card device from the Device Manager by selecting its device name and press the Remove button Then go through the driver installation process again After your card is properly installed on your system you can now configure your device using the Advantech Navigator after you install DAQNavi on your computer PCIE 1760 User Manual 12 Chapter 3 Signal Connections 3 1 Overview Maintaining signal connections is one of the most important factors in ensuring that your application system is sending and receiving data correctly A good signal con nection can avoid unnecessary and costly damage to your PC and other hardware devices This chapter provides useful information about how to connect input and output signals to the PCIE 1760 via the I O connector 3 2 Mo os pis 123 oo JPL6 123 DDD JP14 123 Switch and Jumper Settings JPS JP9 JP10 JP11 JP12 JP13 doco po
15. he frequency value of the signal connected to counter input po TEE CLK pin Counter Value Frequency 10 kHz 3 PCIE 1760 User Manual 3 Pulse Width measurement PCIE 1760 built in counter can measure the pulse width value of the signal connected to counter input Counter Input PLSLIULSLS ILD UUN UT CLK pin TE Counter Value Pulse Width 5 ms 4 Pulse Output with Interrupt PCIE 1760 counter has internal clock that you can produce periodic output signal with interrupt generated at the same time PCIE 1760 counter will use internal clock as time base to fulfill the frequency you want to set PCIE 1760 supports two output types pulse and toggled See figure below as exam ple the desired frequency is 3 MHZ The internal clock is 20 MHz so PCIE 1760 will periodically generate output signal and interrupt every 6 pulses of the internal clock 20 MHz 3 MHz 6 67 cig Si E ana d LIL WU EU BLE LTL Interrupt Pulsetype e Lis iwi Rigel Lis Counter Output PWM pin Toggled type Note Ifthe output signal logic high time or logic low time see figure below is less than 100 Us you cannot see the output signal This is because PCIE 1760 is equipped with photocouple component on PWM output channel and their response time is not fast enough to make the fre quency faster than 20 kHz Logic high time Logiclow time PCIE 1760 User Manual 4 5 Delay Pulse Generation Using PCIE 1760 interna
16. he man ufacturer Discard used batteries according to the manufacturer s instructions Document Feedback To assist us in making improvements to this manual we would welcome comments and constructive criticism Please send all such in writing to support advan tech com Safety Instructions 1 2 3 10 11 12 13 14 15 16 17 Read these safety instructions carefully Keep this User Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning For plug in equipment the power outlet socket must be located near the equip ment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or electrical shock Never open the e
17. it only by its edges DO NOT TOUCH the exposed metal pins of the connector or the electronic components Note Keep the anti static bag for future use You might need the original bag N to store the card if you have to remove the card from PC or transport it El elsewhere PCIE 1760 User Manual 10 2 3 2 4 Driver Installation We recommend you to install the driver before you install the PCIE 1760 card into your system since this will guarantee a smooth installation process The Advantech device driver installation for the PCIE 1760 card is included on the companion CD ROM that is shipped with your DA amp C card package Hardware Installation Note Make sure you have installed the driver first before you install the card After the device driver installation is completed you can now go on to install the PCIE 1760 card in any PCI Express slot on your computer Follow the steps below to install the card on your system 1 Turn off your computer and unplug the power cord and cables TURN OFF your computer before installing or removing any components on the computer 2 Remove the cover of your computer 3 Remove the slot cover on the back panel of your computer 4 Touch the metal part on the surface of your computer to neutralize the static electricity that might be on your body 5 Insert the PCIE 1760 card into a PCI Express slot Hold the card only by its edges and carefully align it with the slot Insert the card fir
18. l clock you can generate a sin gle pulse after a specific period starting from a trigger signal connecting to counter gate input For example if you define the count equals to 3 as figure below a single pulse will be generated after 3 pulses of internal clock signals pass after a trigger signal from counter gate becomes high Counter Gate Gate pin External Clock TO T ri i RS A ST Pulse type Interrupt t Interrupt t i Counter Output PWM pin Toggled type Interrupt 1 Interrupt 1 Note If the output signal logic high time or logic low time see figure below is less than 100 us you cannot see the output signal This is because El PCIE 1760 is equipped with photocouple component on PWM output channel and their response time is not fast enough to make the fre quency faster than 20 kHz Logic high time Logic low time 5 PCIE 1760 User Manual 6 PWM Output PCIE 1760 can generate PWM pulse width modulation signal which you can configure its logic high time and logic low time as figure below Logic high time a lt Logic low time Digital Filter for Digital Input Channels The PCIE 1760 includes a programmable digital filter on each digital input channel to eliminate the unexpected signal or noise from the card s inputs When the digital filter is enabled the state of the corresponding input channel will not update immediately until one high low signal has lasted for a period which is programme
19. mly into place Use of excessive force must be avoided otherwise the card might be damaged 6 Fasten the bracket of the PCI Express card on the back panel of the computer 7 Connect appropriate accessories to the PCI Express card 8 Replace the cover of your computer chassis Re connect the cables you removed in step 2 9 Plugin the power cord and turn on the computer Note In case you installed the card without installing the Device Drivers first Win95 98 ME will recognize your card as an unknown device after rebooting and will prompt you to provide the necessary driver Ignore the prompting messages just click the Cancel button and set up the driver according to the steps described in 2 3 Driver Installation 11 PCIE 1760 User Manual After the PCIE 1760 card is installed you can verify whether it is properly installed on your system through the Device Manager 1 Access the Device Manager through Control Panel System Device Manager 2 The device name of the PCIE 1760 should be listed on the Device Manager tab as follows File Action View Help 9 F G BE a 4 DQA PC amp Advantech Common Motion Card 4 Di Advantech DAQ Devices amp Demo Device 1 MS s 12 14 16 bit 8 ch multifunction card PCIE 1760 8 ch relay 8 ch isolated DI 2 ch counter timer card Ni Computer a Disk drives E Display adapters 3 Floppy disk drives ee Floppy drive controllers tg IDE ATA ATAPI controllers K
20. or for isolated input and output channels High ESD protection 2 000 Vpc High over voltage protection 70 Vpc Wide input range 10 30 Vpc Board ID to identify specific card when multiple devices are installed The Advantech PCIE 1760 offers the following main features Robust Protection The PCIE 1760 digital input channels feature robust isolation protection for industrial lab and machinery automation applications It durably withstands voltage up to 2 500 Voc preventing your host system from any incidental harm If connected to an exter nal input source with surge protection the PCIE 1760 can offer up to a maximum of 2 000 Vpc ESD Electrostatic Discharge protection Even with an input voltage rising up to 70 Vpc the PCIE 1760 can still manage to work properly albeit only for a short period of time Plug and Play Function The PCIE 1760 is a Plug and Play device which fully complies with PCI Express Specification Rev V1 0 During card installation there is no need to set jumpers or DIP switches Instead all bus related configurations such as base I O address and interrupt are automatically done by the Plug and Play function PCIE 1760 User Manual 2 Board ID The PCIE 1760 has a built in DIP Switch that helps define each card s ID when multi ple PCIE 1760 cards have been installed on the same PC chassis The board ID set ting function is very useful when users build their system with multiple PCIE 1760 cards With co
21. our dealer Edition 1 Printed in Taiwan January 2013 PCIE 1760 User Manual ii Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech Please contact your local supplier for ordering information CE This product has passed the CE test for environmental specifications Test conditions for passing included the equipment being operated within an industrial enclosure In order to protect the product from being damaged by ESD Electrostatic Discharge and EMI leakage we strongly recommend the use of CE compliant industrial enclo sure products FCC Class B Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installa tion This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interfer ence to radio or television reception which can be determined by turning the equip ment off and on the user
22. quipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture PCIE 1760 User Manual iv 18 19 20 21 22 23 The equipment does not work well or you cannot get it to work according to the user s manual The equipment has been dropped and damaged The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAMAGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A Safety Precaution Static Electricity DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage To avoid electrical shock
23. rrect Board ID settings you can easily identify and access each card during hardware configuration and software programming Counter Input and PWM Input Output PCIE 1760 offer two counter inputs which can perform event counting frequency measurement and pulse width measurement Counters on PCIE 1760 have a counter value match interrupt function When this interrupt function is enabled an interrupt signal will be generated if the counter value reaches a pre set counter match value The counter will continue to count until an overflow occurs then it will go back to its reset value zero and continue the counting process A user can set each individual counter channel to count either falling edge high to low or rising edge low to high signals Except measurement functionality counter input channels can combine with PWM output channels to generate single pulse pulse train or PWM pulse width modu lated output signal A pulse width modulated waveform is created when the High and Low periods of a periodic rectangular signal are varied Using PCIE 1760 user can individually set each PWM channel s High and Low periods for from 2 to 232 1 units 1 unit 50 Us depending on his needs 1 Event counter PCIE 1760 built in counter can calculate how many pulse are sent into the input channel Counter Input LI CLK pin Counter Value 1 2 3 4 5 6 2 Frequency measurement PCIE 1760 built in counter can measure t
24. ssumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any on screen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to y
25. the accessories for enhanced operation of your card you can then begin the Installation procedures Software Overview Advantech offers device drivers SDKs third party driver support and application software to help fully exploit the functions of your PCIE 1760 card All these software packages are available on the companion CD ROM or you can browse Advantech website to get the latest update http www advantech com 7 PCIE 1760 User Manual 1 6 Accessories Advantech offers a complete set of accessory products to support the PCIE 1760 card These accessories include Wiring Cable The PCL 10137 shielded cable is specially designed for PCIE 1760 cards to provide high resistance to noise To achieve better signal quality the signal wires are twisted in such a way as to form a twisted pair cable reducing cross talk and noise from other signal sources Furthermore its digital lines are separately sheathed and shielded to neutralize EMI EMC problems Wiring Boards The ADAM 3937 is a 37 pin D type wiring terminal module for DIN rail mounting This terminal module can be readily connected to the Advantech cards and allow easy yet reliable access to individual pin connections for the PCIE 1760 card PCIE 1760 User Manual 8 Chapter 2 Hardware Installation 2 1 2 2 Installation This chapter gives users a package item checklist proper instructions about unpack ing and step by step procedures for both driver
Download Pdf Manuals
Related Search