MANUBAL C40 instructions
Contents
1. MANUBAL C40 User Manual Read carefully before operating the Manubal bale grab UK 365080 AA 0511 Original instructions Dear user We thank you for placing your trust in our product and hope you will find your MX MANUBAL satisfactory in every Way Taking a few minutes to read this manual will enable you to use the capabilities of your MX MANUBAL to the full prolong its service life and ensure safe operation The MANUBAL user manual before you is an important document please retain it in order to be able to refer to it if required Make it available to any other users and hand it over it to any new owner in the event of your MX MANUBAL being sold on The illustrations and technical data shown in this document might not match your MX MANUBAL bale grab exactly operating conditions will nevertheless remain the same The user must read and understand this manual before first use 8 9 TABLE OF CONTENTS SAFETY RULES SAFETY STICKERS IDENTIFICATION PLATE HITCHING THE MANUBAL UNHITCHING THE MANUBAL ADJUSTING THE MANUBAL ACCORDING TO THE BALE DIAMETER POWER CONTROL SYSTEM MAINTENANCE STORAGE TECHNICAL SPECIFICATIONS EC DECLARATION OF CONFORMITY Page 10 1 SAFETY RULES The tractor loader or telescopic handler MANUBAL bale grab combination must only be operated by trained and experienced personnel For your complete safety and that of others strict compliance with the hitch2. by anyone else without first requesting written authorisation from MX Failure to comply with these rules may render your MANUBAL bale grab hazardous In the event of damage or injury MX shall not be held responsible in any way Warranty cover will cease immediately in the event of failure to observe the standards and instructions for use and maintenance of the MANUBAL bale grab as stipulated in the user manual THE INSTALLER SHALL BE FULLY LIABLE FOR ANY FITMENT ON A LOADER OTHER THAN MX OR A TELESCOPIC HANDLER WHICH HAS NOT BEEN RECOMMENDED BY MX MX Z 19 rue de Rennes BP 83221 F 35690 ACIGN 5 Modification reserved 2 SAFETY STICKERS Ensure the labels are clean and legible replace them if damaged 1 Location exterior left hand side Familiarise yourself with the safety rules in the user manual before using or working on the unit 2 Location exterior left hand side Familiarise yourself with the safety rules in the user manual before using or working on the unit MX implements are designed to offer the operator of the prime mover to which they are fitted optimum angles for crowding and dumping at ground level Before handing over to the operator the installer must check that there is no possibility of interference occurring between the implement which has been fitted and other components of the machine tyres mudguards etc as a result of the maximum travel of the implem
3. pins are retracted springs are compressed CAUTION check implement hoses are away from hitching area 4 1 2 Approach the loader towards the implement Slot the self centering V onto the implements hitching brackets Crowd the implement back while driving forwards until the unlocking lever is triggered 4 1 3 Turn the engine off Decompress the loader s hydraulic lines feeding the implement N B If the loader is fitted with a solenoid valve decompress with contact turned on and the control button pressed 4 1 4 Connect the couplers when implement with hydraulic functions MX Z 19 rue de Rennes BP 83221 F 35690 ACIGN 7 Modification reserved 5 UNHITCHING THE MANUBAL 5 1 Implement carrier with manual unlocking 5 1 1 Before leaving the operators seat Select a stable parking area Lower the implement horizontally to 0 30 m from the ground Pull on the handbrake Turn off the engine Decompress the loader s hydraulic lines feeding the implement NOTA When loader fitted with one or several solenoid valves leave contact on and move the lever Left Right while pressing the buttons 5 1 2 Implement unhitching From the L H side of the loader pull on the lever to the end Never operate from the front of the implement Then move the lever backwards to lock it compressed springs Disconnect the hydraulic s MACH 2 disconnect Couplings disconnect and place plastic caps on the
4. e wear bushes and replace them before they are fully worn 8 2 Storage Unhitch the MANUBAL bale grab with the grab opened ram rod retracted Lubricate pivot points 9 TECHNICAL SPECIFICATIONS O Lf TT pi EY II gt 5_ I 7 Stacking height Overall height H Overall width gran closed L Distance grab closed pf Loader model MX Z 19 rue de Rennes BP 83221 F 35690 ACIGN 10 4 round bales H 1 20 m 740 mm 1620 mm 310 mm 320 mm 210 kg as from MX T6 Modification reserved EC DECLARATION OF CONFORNITY Ce The manufacturer MX 19 Rue de Rennes F 35690 Acign Hereby declares that the following equipment Manubal C40 Comply with EC directive 2006 42 of the Council of European Parliament and of the council of 17th of May 2009 relating to machines Acign 1st of September 2010 D Lo c Mailleux Technical Director MX Z 19 rue de Rennes BP 83221 F 35690 ACIGNE T l 33 0 2 99 62 52 60 Fax 33 0 2 99 62 50 22 e mail contact m x eu
5. ent installed when the telescopic handler boom positions the implement closest in to the machine In the event of the aggregation of positional conditions of the implement and the boom leading to interference the installer is to notify the operator and provide him with instructions on how to prevent such interference In general it is sufficient to operate with the boom extended by at least 0 5 m MX cannot be held liable for any damage or accidents which might result from impacts caused by this 3 PLAQUE D IDENTIFICATION Identification details are to be passed on to your dealer with any request for spare parts or service work Its location is shown below 3 Location MANUBAL frame carrier MANUBAL identification data plate CE 19 rue de Rennes F 35690 ACIGN D signation Designation Type Model Typ N de s rie Serial number Seriennummer Ann e Year Poids vide k Unloaded weight Leergewicht g 328462 MX Z 19 rue de Rennes BP 83221 F 35690 ACIGN 6 Modification reserved 4 HITCHING THE MANUBAL A Caution This operation must be carried out by the driver who must leave the seat and ensure all manoeuvres are forbidden while he is working on the loader 4 1 Implement carrier with manual unlocking 4 1 1 Check the unlocking lever is in the hitching position lever turned backwards Locking
6. ing and unhitching procedure for the MANUBAL bale grab is required chapter 5 of this manual Only control the MANUBAL bale grab from the driver s seat Keep operating the controls until movements stop Do not leave the driver s seat without stopping all control movements All personnel must be kept away from the area in which the loader or telescopic handler MANUBAL bale grab combination is moving while it is in operation Never pass under a raised bale Never use the MANUBAL bale grab to push a bale Carrying or lifting personnel using the MANUBAL bale grab is forbidden Never stand or pass under the load Before any operation the user must ensure thattne MANUBAL bale grab is in proper working order and can be used in complete safety He must also check and ensure that the tractor loader MANUBAL bale grab combination is stable by fitting a counterweight to the back of the tractor This should ensure that 20 of gross weight remains on the rear axle of the tractor for optimum safety while travelling and working When travelling on the road it is imperative that the regulations governing use on the public highway be observed size implement markings etc The grab must be closed Take great care when operating at height in order to avoid catching any items electric power or telephone lines guttering roof trusses etc Whenever the tractor or telescopic handler is stopped momentarily or for an extended period the engine must be shut d
7. male and female couplings Place the hoses on the front of the implement MX Y 19 rue de Rennes BP 83221 F 35690 ACIGN 8 Modification reserved 6 ADJUSTING THE MANUBAL ACCORDING TO THE BALE DIAMETER To optimise picking up wrapped bales an adjustment can be made according to their diameter Setting 1 Picking up wrapped bales around 1 m to 1 25 m in diameter Setting 2 Picking up wrapped bales around 1 25 m to 1 50 m in diameter Setting 3 Picking up wrapped bales around 1 50 m to 1 75 m in diameter 7 POWER CONTROL SYSTEM The Power Control System pressure limiter is used to adjust the tightening force of the grab on the wrapped bale The adjustment is made by a valve incorporated into the pressure limiter unit When the adjustment is made lock the adjustment with the thumbwheel amp Option MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN 9 Modification reserved 8 MAINTENANCE STORAGE 8 1 Maintenance Lubricate pivot points regularly The greasing points are shown on the MANUBAL by stickers lt lt Ensure hydraulic connections are cleaned each time before they are connected See toit that straw or hay residues do not jam up the pivot points Check the MANUBAL bale grab to ensure that it is in proper working order throughout and that screws clips and pins are in place before any use Check the condition of th
8. own and the MANUBAL bale grab lowered Check periodically to ensure that safety pins and bolts are in place Do not replace them with any other items such as nails wire etc Any adjustment on the MANUBAL bale grab position of the backplate tubes Power Control System adjustment must be carried out after the MANUBAL bale grab has been lowered to the ground and the tractor or telescopic handler engine shut down Any work involving fault tracing diagnostics and or disassembly of parts may only be undertaken by a skilled technician who will start with an assurance that the work will be carried out in complete safety for himself and his surroundings A Caution Check hoses for length and routing in all configurations fully crowded fully dumped etc before first use The MANUBAL bale grab is designed to withstand a maximum operating pressure of 210 bar Above this pressure the MANUBAL bale grab will require to be fitted with a pressure limiter Any instance of a MANUBAL bale grab being fitted which ignores the recommendations in the MX price list in force on the date of purchase will void MX warranty on the entire supply Any modification to any part of the MX supply rams grab tines crank etc or use of a component installed on the MANUBAL bale grab which has not originated from MX will void MX warranty on the entire MX supply Use only genuine MX spare parts Do not modify your MANUBAL bale grab yourself or have it modified
Download Pdf Manuals
Related Search