Product ManualDownload PDF
Contents
1. PROBLEM CAUSE SOLUTION Line trimmer 1 The battery pack is not 1 Attach the battery pack to the doesn t work attached to the trimmer trimmer 2 No electrical contact between 2 Remove battery check contacts the trimmer and battery and reinstall the battery pack 3 The battery pack is depleted 3 Charge the battery pack 4 The battery pack or line 4 Allow the battery pack or trimmer trimmer is too hot to cool until the temperature drops below 67 C 5 The lock off lever and trigger 5 Press down the lock off lever and are not depressed hold it then depress the trigger to simultaneously turn on the line trimmer 6 The motor is overloaded 6 Stop the trimmer remove the battery and clean the cutting attachment restart the trimmer 4 4 Cutting attachment 1 Cutting attachment is bound Stop the trimmer remove the will not advance line with grass battery and clean the cutting attachment 2 Not enough line on spool 2 Remove the battery and replace the cutting line follow the section LINE REPLACEMENT in this manual 3 Cutting attachment is dirty 3 Remove the battery and clean the spool and spool base 4 Line is tangled on spool 4 Remove the battery and remove the line from the spool and rewind follow the section LINE REPLACEMENT in this manual 5 Line is worn too short 5 Remove the battery and pull the lines while alternately pressing down on a2. 1 Wind the spool with new line 2 Install a pre wound spool Wind the spool with new line A WARNING To prevent serious personal injury remove the battery pack from the tool before servicing cleaning changing attachments or removing material from the unit 1 Press the release tabs on the spool retainer and remove the spool retainer by pulling it straight out Fig 16 2 Remove the spool Use a clean cloth to clean the inner surface of the spool base NOTICE Always clean the spool and spool base before reassembling the bump head 3 Check the spool retainer spool and spool base for wear If necessary replace the wear parts 4 Take approximately 5m of new cutting line Fold the line in half and then adjust it so that one end is 10cm longer than the other Fig 17 56V LITHIUM ION CORDLESS LINE TRIMMER 23 GO 5 Hook the folded end of the cutting 18 line onto either of the slots in the spool Fig 18 Wind Direction a 6 Wind the line in two even and tight layers onto the spool Wind the line in the direction indicated on the spool Fig 18 NOTICE Failure to wind the line in the direction indicated will cause the bump head to operate incorrectly 7 Place the ends of the line in two opposite notches in the spool with approximately 10cm protruding Fig 19 8 Align the notches of the spool from which the lines protrude with the eyelets in the
3. REAR HANDLE Ergonomic handle with overmold improves comfort and grip TRIGGER To turn the line trimmer On and Off LOCK OFF LEVER Helps prevent accidental or unauthorized activation of the trigger It must be depressed before the trigger can be activated SHAFT Encloses and protects the cables between the motor and rear handle BUMP HEAD CUTTING HEAD The cutting attachment for cutting grass BUMP KNOB Lightly tap the bump knob on the ground while operating the trimmer to release the cutting line GUARD Designed to reduce the risk of injury from foreign objects flung backwards toward the operator by the cutting attachment and from contact with the cutting attachment BUMP PROTECTOR Limits the cutting range and reduces cutting line wear LINE CUTTING BLADE Steel blade on the guard keeps the cutting line at the proper length BATTERY RELEASE BUTTON Press to release the battery pack from the tool LATCH Locks the battery pack when installing it on the tool EJECTION MECHANISM Aids in battery removal 16 56V LITHIUM ION CORDLESS LINE TRIMMER GO OPERATION AX WARNING Do not allow familiarity with this product to make you careless Remember that a careless fraction of a second is sufficient to inflict serious injury AX WARNING Always wear eye protection with side shields marked to comply with AS1337 1 2010 along with hearing protection Failure to do so could result in objects being thrown into your eyes and o
4. the tool before servicing cleaning changing add on attachments or removing material from the unit CLEANING THE UNIT Clean the unit using a damp cloth with a mild detergent Do not use any strong detergents on the plastic housing or the handle They can be damaged by certain aromatic oils such as pine and lemon and by solvents such as kerosene Moisture can also cause a shock hazard Wipe off any moisture with a soft dry cloth Use a small brush or the air discharge of a small vacuum cleaner brush to clean the air vents on the motor housing Keep the air vents free of obstructions STORING THE UNIT Remove the battery pack from the line trimmer when it is not in use Clean the tool thoroughly before storing it Store the unit in a dry well ventilated area locked up or up high out of the reach of children Do not store the unit on or adjacent to fertilizers petrol or other chemicals 56V LITHIUM ION CORDLESS LINE TRIMMER 2l GO Protecting the environment Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems available If electrical appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain damaging your health and well being 28 56V LITHIUM ION CORDLESS LINE TRIMMER GO TROUBLESHOOTING
5. 4 Adjust the front assist handle position between the soft sleeve housing and warning label on the shaft Fig 5 Shorter users may adjust handle to a lower position away from you and taller users may adjust the handle to an upper position towards you The handle should be adjusted so that your front arm is straight when using the trimmer 5 Tighten the four screws so that the handle cannot be rotated on the shaft PACKING LIST PART NAME QUANTITY Line Trimmer 1 Guard 1 Front assist handle assembly 1 Operating manual 1 14 56V LITHIUM ION CORDLESS LINE TRIMMER GO DESCRIPTION KNOW YOUR LINE TRIMMER Fig 6a amp 6b Rear Handle Lock Off Lever Battery Release Adjustable Front Assist Handle Shaft Bump Protector Electric Contacts Bump Head Cutting Head Line Cutting Blade Bump Knob Ejection Mechanism AX WARNING Never operate the tool without the guard firmly in place The guard must always be on the tool to protect the user AX WARNING The safe use of this product requires an understanding of the information on the tool and in this operator s manual as well as knowledge of the project you are attempting Before use of this product familiarize yourself with all operating features and safety rules 56V LITHIUM ION CORDLESS LINE TRIMMER 15 GO ADJUSTABLE FRONT ASSIST HANDLE For easy control of the trimmer during cutting
6. in daylight or good artificial light Always turn the line trimmer off or remove the battery pack whenever leaving the trimmer unattended To prevent accidental starting that could cause serious personal injury always remove the battery pack from the tool before checking cleaning or working on the machine Always clearing a blockage when the battery pack is removed from the line trimmer Don t Use In Rain Keep Children Away All visitors should be kept at a distance from work area 56V LITHIUM ION CORDLESS LINE TRIMMER I GO Dress Properly Do not wear loose clothing or jewelry They can be caught in moving parts Use of rubber gloves and substantial footwear is recommended when working outdoors Wear protective hair covering to contain long hair Use Safety Glasses Always use a face or dust mask if operation is dusty Use the Right Tool Do not use the tool for any job except that for which it is intended Don t Force the Trimmer It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed Don t Overreach Keep proper footing and balance at all times Stay Alert Watch what you are doing Use common sense Do not operate the trimmer when you are tired Do not operate the trimmer while under the influence of alcohol or drugs Keep guards in place and in working order Keep hands and feet away from the cutting area After extending n
7. or skin It may be toxic if swallowed Exercise care in handling batteries in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause burns Replacement Parts When servicing use only identical EGO replacement parts Use of any other accessory or attachment may increase the risk of injury Battery tools do not have to be plugged into an electrical outlet therefore they are always in operating condition Be aware of possible hazards even when the tool is not operating Take care when performing maintenance or service Remove or disconnect battery pack before servicing cleaning or removing material from the trimmer Do not wash with a hose avoid getting water in motor and electrical connections Save these instructions Refer to them frequently and use them to instruct others who may use this tool If you loan this tool to someone else also loan these instructions to them to prevent misuse of the product and possible injury SAVE THESE INSTRUCTIONS 10 56V LITHIUM ION CORDLESS LINE TRIMMER GO INTRODUCTION Congratulations on your selection of 56 Volt Lithium lon Cordless Line Trimmer It has been designed engineered and manufactured to give you the best possible dependability and performance Should you experience any problem you cannot easily remedy please contact EGO customer service center 1300 000 EGO 1300 000 346 This manual contains imp
8. pets are nearby i 56V LITHIUM ION CORDLESS LINE TRIMMER GO Before using the machine and after any impact check for signs of wear or damage and repair as necessary Always hold the trimmer firmly with both hands on the handles while operating Wrap your fingers and thumbs around the handles Avoid Accidentally Starting Don t carry the trimmer with your finger on the trigger Do not operate the trimmer in petrolic or explosive atmospheres Motors in these appliances normally spark and the sparks might ignite fumes Damage to Trimmer If you strike a foreign object with the trimmer or it becomes entangled stop the tool immediately remove the battery pack from the line trimmer check for damage and have any damage repaired before further operation is attempted Do not operate with a broken guard or spool If the equipment should start to vibrate abnormally stop the motor remove the battery pack from the line trimmer and check immediately for the cause Vibration is generally a warning of trouble A loose head may vibrate crack break or come off the trimmer which may result in serious or fatal injury Make sure that the cutting attachment is properly fixed in position If the head loosens after fixing it in position replace it immediately Never use a trimmer with a loose cutting attachment Replace a cracked damaged or worn out cutting head immediately even if damage is limited to superficial cracks Such attachments
9. to turn on the line trimmer Trigger The motor runs only when the 99 lock off lever and trigger are operated simultaneously To stop the line trimmer Release the lock off lever and trigger to stop the line trimmer WARNING Always remove the battery pack from the line trimmer during work breaks and after finishing work USING THE LINE TRIMMER AX WARNING To avoid serious personal injury wear goggles or safety glasses at all times when operating this unit Wear a face mask or dust mask in dusty locations Clear the area to be cut before each use Remove all objects such as rocks broken glass nails wire or line that can be thrown or become entangled in the cutting attachment Clear the area of children bystanders and pets At a minimum keep all children bystanders and pets at least 30m away there still may be risk to bystanders from thrown objects Bystanders should be encouraged to wear eye protection If you are approached stop the motor and cutting attachment immediately 56V LITHIUM ION CORDLESS LINE TRIMMER 19 GO A WARNING To prevent serious personal injury remove the battery pack from the tool before servicing cleaning changing attachments or removing material from the unit Before each use check for damage worn parts Check the bump head guard and front assist handle and replace the parts that are cracked warped bent or damaged in any away The line cutting blade on the edge of the
10. wear If necessary replace the wear parts Place a pre wound spool on the spool retainer Align the notches of the spool from which the lines protrude with the eyelets in the spool retainer and position the spool in the retainer Fig 20 Hold the spool and spool retainer grasp the line and pull it to release the line from the notch in the eyelet Fig 21 Check to see if the spring is properly located in the spool base If it comes loose or drops out position the spring in the mounting hole of the spool base and press it in place Fig 22 With the spool base facing downward align the tabs on the spool retainer with the slots in the spool base and press the retainer evenly down until it snaps into place Fig 23 26 56V LITHIUM ION CORDLESS LINE TRIMMER GO MAINTENANCE A WARNING When servicing use only identical replacement parts Use of any other parts may create a hazard or cause product damage Inspect and maintain the machine regularly To ensure safety and reliability all repairs should be performed by a qualified service technician A WARNING Battery tools do not have to be plugged into an electrical outlet therefore they are always in operating condition To prevent serious personal injury take extra precautions and care when performing maintenance service or for changing the cutting attachment or other attachments A WARNING To prevent serious personal injury remove the battery pack from
11. with your thumb the battery pack will disengage from the latch Press to Release Grasp the battery pack and remove it from the line trimmer HOLDING THE LINE TRIMMER A WARNING Dress properly to reduce the risk of injury when operating this tool Do not wear loose clothing or jewelry Wear eye and ear hearing protection Wear heavy long pants boots and gloves Do not wear short pants sandals or go barefoot Before operating the unit stand in the operating position and check that The operator is wearing eye protection and proper clothing One arm is slightly bent and the hand on that arm is holding the rear handle The other arm is straight with that hand holding the front assist handle The trimmer head is parallel to the ground and easily contacts the material to be cut without the operator having to bend over Fig 9 18 56V LITHIUM ION CORDLESS LINE TRIMMER GO STARTING STOPPING THE LINE TRIMMER Before starting the line trimmer m Make sure you have a secure and balanced footing Stand upright and hold the line trimmer in a relaxed position Make sure that the cutting line is not touching the ground or any other objects m Hold the line trimmer with both hands One hand on the rear handle and one hand on the front assist handle To start the line trimmer Fig 10 1 Press down the lock off lever and hold it in that position 2 Depress the trigger
12. 2650 POWERD LINE TRIMMER OPERATING MANUAL 56 VOLT LITHIUM ION CORDLESS LINE TRIMMER MODEL NUMBER ST1200E AN WARNING To reduce the risk of injury the user must read and understand the Operator s Manual before using this product Save these instructions for future reference GO TABLE OF CONTENTS Read All Instructions Aa 3 Safety OND cipccceeceveesveesuee dene bane ameabad eben 4 Safety INStructions 5 10 Introduction uann 11 Specifications 11 ASSEMDIY anaazansanaasunanananaannna 12 14 ay YA AA afua biih hibhhhii hiihii 14 DeSCHPHON ASA ee es eee AA 15 16 EIA niiina irinna ded ooh dedded doh dod deano 17 26 MAM AAA 27 28 Troubleshooting annaaasssana 29 Warranty 0 ccc cece cece eee eee eee 30 31 Palilia 32 33 2 56V LITHIUM ION CORDLESS LINE TRIMMER GO READ ALL INSTRUCTIONS A READ amp UNDERSTAND LU INSTRUCTION MANUAL This line trimmer has many features for making its use more pleasant and enjoyable Safety performance and dependability have been given top priority in the design of this product making it easy to maintain and operate A DANGER People with electronic devices such as pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacem
13. ST 56V LITHIUM ION CORDLESS LINE TRIMMER MODEL NUMBER ST1200E The Model Number will be found on the Nameplate attached to the housing of the line trimmer Always mention the Model Number when ordering parts for this tool EXPLODED VIEW 32 56V LITHIUM ION CORDLESS LINE TRIMMER GO PARTS LIST INDEX PART NO DESCRIPTION QTY NUMBER 1 2823713000 Line cutting blade set 1 2 2823710000 Guard assembly 1 3 2823712000 Spool retainer assembly 1 4 3800097000 Cutting line 1 5 2823045000 Spool assembly 1 6 2823709000 Bump head assembly 1 7 2823711000 Front assist handle assembly 1 8 3660269000 Spring in the bump head 1 9 2822959000 Hexagon nut set for bump head 1 10 3650148000 Bump protector 1 56V LITHIUM ION CORDLESS LINE TRIMMER 3 3
14. aker could cause interference or failure of the pacemaker AX WARNING To ensure safety and reliability all repairs should be performed by a qualified service technician 56V LITHIUM ION CORDLESS LINE TRIMMER 3 GO SAFETY SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers The safety symbols and the explanations with them deserve your careful attention and understanding The symbol warnings do not by themselves eliminate any danger The instructions and warnings they give are no substitutes for proper accident prevention measures AX WARNING Be sure to read and understand all safety instructions in this Operator s Manual including all safety alert symbols such as DANGER WARNING and CAUTION before using this tool Failure to following all instructions listed below may result in electric shock fire and or serious personal injury SYMBOL MEANING SAFETY ALERT SYMBOL Indicates DANGER WARNING OR CAUTION May be used in conjunction with other symbols or pictographs WARNING The operation of any power tools can result in foreign objects being thrown into your eyes which can result in severe eye damage Before beginning power tool operation always wear safety goggles or safety glasses with side shields and a full face shield when needed We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields Always use eye protection co
15. d repair or from use of any cutting line other than the EGO authorized cutting line recommended for use with this product e This warranty only covers defects arising under normal usage and does not cover any malfunction failure or defect resulting from misuse abuse including overloading of the product beyond capacity and exposure to water or rain accidents neglect or lack of proper installation and improper maintenance or storage f This warranty does not cover normal deterioration of the exterior finish including but not limited to scratches dents paint chips or to any corrosion or discoloring by heat abrasive and chemical cleaners 3 I 56V LITHIUM ION CORDLESS LINE TRIMMER GO HOW TO OBTAIN SERVICE For warranty service please contact EGO customer service on 1300 000 EGO 1300 000 346 When requesting warranty service you must present the original dated sales receipt An authorized service center will be selected to repair the product according to the stated warranty terms ADDITIONAL LIMITATIONS Chervon Australia Pty Ltd ABN 36 165 077 501 Chervon warrants to the original domestic purchaser that this product will be free from defects in materials and workmanship for 5 years from date of purchase and any battery or charger will be free from defects in materials and workmanship for 3 years from date of purchase To make a claim return the faulty item together with proof of purchase directly to your closest serv
16. er Minute Revolutions per minute b 56V LITHIUM ION CORDLESS LINE TRIMMER GO IMPORTANT SAFETY INSTRUCTIONS A WARNING When using electric trimmers basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE AX DANGER Do not rely on the tool s insulation against electric shock To reduce the risk of electrocution never operate the tool in the vicinity of any wires or cables power etc which may carry electric current A CAUTION Wear appropriate personal hearing protection during use Under some conditions and durations of use noise from this product may contribute to hearing loss Read the instructions carefully Be familiar with the controls and the proper use of the line trimmer This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Avoid Dangerous Environments Don t use trimmers in damp or wet locations Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property Use the machine only
17. ew cutting line always return the machine to its normal operating position before switching on Store Trimmer Indoors When not in use the trimmer should be stored indoors in a dry and high or locked up place with the battery pack removed out of reach of children Maintain Trimmer With Care Keep the cutting attachment clean for best performance and to reduce the risk of injury Follow instructions for changing accessories Keep handles dry clean and free from oil and grease Check Damaged Parts Before further use of the trimmer a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other condition that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual Never operate the machine with damaged guards or shields or without guards or shields in place Clear the area to be cut before each use Remove all objects such as rocks broken glass nails wire or line that can be thrown or become entangled in the cutting attachment Make sure that other persons and pets are at least 30m away Always ensure that the ventilation openings are kept clear of debris Stop using the machine while people especially children or
18. guard can dull over time It is recommended that you periodically sharpen it with a file or replace it with a new blade A WARNING Always wear gloves when mounting or replacing the guard or sharpening or replacing the blade Take care of the blade on the guard and protect your hand from cutting After each use clean the trimmer A WARNING To prevent serious personal injury remove the battery pack from the tool before servicing cleaning changing attachments or removing material from the unit Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the tool never immerse any part of the tool into a liquid oe Wipe off the unit with a clean dry soft cloth Keep air vents in the motor housing and shaft free from debris at all times Fig 11 Ad CAUTION Obstructions in the vents will prevent the air from flowing into the motor housing and result in Air vents in motor housing overheating or damaged of the motor AX WARNING Never use water for cleaning your trimmer Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents Use clean cloths to remove dirt dust oil grease etc 20 56V LITHIUM ION CORDLESS LINE TRIMMER GO Tips for best trimming results Fig 12 The correct angle for the cutting attachment is parallel to the ground This line trimmer allows you to rest the bum
19. ice agent or to the place of purchase Any handling and transportation costs and other expenses incurred in claiming this warranty are not covered by this warranty and will not be borne by Chervon The replacement product or part or repaired product will be made available for your collection at an address nominated by Chervon Where a valid warranty claim is made Chervon will replace the defective product or repair the fault Where the product is repaired Chervon may use refurbished parts This warranty does not cover normal wear and tear misuse or abuse This warranty may also be further limited or voided as specifically detailed in the product Manual Chervon has no other liability under this warranty The benefits to you given by this warranty are in addition to other rights and remedies imposed by State and Federal legislation that cannot be excluded Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Chervon Australia Pty Ltd Unit 13 1488 Ferntree Gully Rd Knoxfield VIC 3180 Phone Number 1300 000 EGO 1300 000 346 Email address support egopowerplus com au 56V LITHIUM ION CORDLESS LINE TRIMMER 31 GO PARTS LI
20. may shatter at high speed and cause serious or fatal injury Check the cutting attachment at regular short intervals during operation or immediately if there is a noticeable change in cutting behavior Only use EGO authorized polymer trimmer line accessories and trimmer line that are designed for use with this tools Although certain unauthorized attachments might be fitted to the EGO line trimmer their use may be extremely dangerous and or damaging to the tools To reduce the risk of serious injury never use wire or metal reinforced line or other material in place of the nylon cutting lines Pieces of wire could break off and be thrown at high speed toward the operator or bystanders To reduce the risk of injury from loss of control never work on a ladder or on any other insecure support Never hold the cutting attachment above waist height If situations occur that are not covered in this manual use care and good judgment Contact the EGO Service Center for assistance 56V LITHIUM ION CORDLESS LINE TRIMMER 9 GO Do not charge the battery pack in rain or in wet locations Use only with battery packs and chargers listed below BATTERY CHARGER BA2240E CH5500E BA1120E CH2100E Do not dispose of the battery in a fire The cells may explode Check with local codes for possible special disposal instructions Do not open or mutilate the battery Released electrolyte is corrosive and may cause damage to the eyes
21. mes more difficult as the cutting line becomes shorter sl v DA LIA Van AI Wh fi aT Nay RI Mi W yo Cy Bump Knob A WARNING Do not remove or alter the line cutting blade assembly Excessive line length will cause the motor to overheat and may result in serious personal injury For best results tap the bump knob on bare ground or hard soil If line release is attempted in tall grass the motor may overheat Always keep the cutting line fully extended Line release becomes more difficult as the cutting line becomes shorter WORKING WITH BUMP PROTECTOR The bump protector can limit the cutting range of the cutting line and reduce the risk of the rotating cutting line causing damage Fig 14 To use the bump protector flip it down from its stored position Fig 15 AA WARNING The bump head may continue to rotate briefly after you switch off the line trimmer Wait for the bump head to come to a complete stop before adjusting the bump protector Do not adjust it with your foot 20 56V LITHIUM ION CORDLESS LINE TRIMMER GO LINE REPLACEMENT A WARNING Always use only EGO authorized replacement nylon cutting line Using line other than that specified may cause the line trimmer to overheat or become damaged AX WARNING Never use metal reinforced line wire or rope etc These can break off and become dangerous projectiles There are two methods to replace the cutting line
22. mplying with Australian Standards AS1337 1 2010 4 56V LITHIUM ION CORDLESS LINE TRIMMER GO SAFETY INSTRUCTIONS This page depicts and describes safety symbols that may appear on this product Read understand and follow all instructions on the machine before attempting to assemble and operate it Safety Alert Precautions that involve your safety Always wear safety goggles or safety Wear Eye Protection glasses with side shields and a full face shield when operating this product Do Not Expose To Do not use in the rain or leave outdoors Moisture while it is raining To reduce the risk of injury user must read and understand operator s manual before using this product WARNING Read operator s manual E Class II Construction Double insulated Construction Ensure that other people and pets remain at Li Keep Bystanders Away least 30m away from the line trimmer when itis in use Ensure that other people and pets remain at ADE Keep Bystanders Away least 30m away from the line trimmer when it is in use 56V LITHIUM ION CORDLESS LINE TRIMMER 5 GO V Volt Voltage A Amperes Current Hz Hertz Frequency cycles per second W Watt Power min Minutes Time AI Alternating Current Type of current mE Direct Current Type or a characteristic of current no No Load Speed Rotational speed at no load min P
23. nd releasing the bump knob Grass wraps around Cutting tall grass at ground level Cut tall grass from the top down to cutting head and prevent wrapping motor housing 56V LITHIUM ION CORDLESS LINE TRIMMER 29 GO EGO WARRANTY POLICY 5 year limited warranty on EGO outdoor power equipment and 3 year limited warranty on EGO Power System battery packs and chargers Please contact EGO customer service on 1300 000 EGO 1300 000 346 any time you have questions or warranty claims SERVICE WARRANTY FOR FIVE YEARS from the date of original retail purchase this EGO product is warranted against defects in material or workmanship Defective product will receive free repair FOR THREE YEARS from the date of original retail purchase the EGO Power System battery pack and charger are warranted against defects in material or workmanship Defective product will receive free repair This warranty does not cover routine maintenance parts and consumables such as the cutting line that can wear out from normal use within the warranty period a This warranty applies only to the original purchaser at retail and may not be transferred b The warranty period for any EGO product or part used for industrial professional or commercial purpose is one year c This warranty is void if the product has been used for rental purpose d This warranty does not cover the damage resulting from modification alteration or unauthorize
24. ortant information on to the safe assembly operation and maintenance of your line trimmer Read it carefully before using the line trimmer Keep this manual handy so you can refer to it at any time SERIAL NUMBER DATE OF PURCHASE YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE SPECIFICATIONS Voltage 56V No load speed 6000 min Cutting Mechanism Bump Head Line Diameter 2 0mm Cutting Width 30cm Weight Without battery pack 2 85kg 56V LITHIUM ION CORDLESS LINE TRIMMER ll GO ASSEMBLY AX WARNING If any parts are damaged or missing do not operate this product until the parts are replaced Use of this product with damaged or missing parts could result in serious personal injury A WARNING Do not attempt to modify this product or create accessories not recommended for use with this line trimmer Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury AX WARNING To prevent accidental starting that could cause serious personal injury always remove the battery pack from the tool when assembling parts UNPACKING This product requires assembly Carefully remove the product and any accessories from the box Make sure that all items listed in the packing list are included Inspect the tool carefully to make sure that no breakage or damage occurred du
25. p knob on the ground for operating more comfortably Do not force the trimmer Allow the very tip of the line to do the cutting Direction of rotation especially along walls Cutting with Dangerous YAN TA more than the tip will reduce cutting cutting area wy yh area efficiency and may overload the motor The cutting height is determined by the distance of the cutting line from the lawn surface Grass over 200mm should be cut by working from top to the bottom in small increments to avoid premature line wear or motor drag Slowly move the trimmer into and out of the area being cut maintaining the trimmer at the desired cutting height This can be either a forward backward or side to side motion Cutting shorter lengths produces best results Trim only when grass and weeds are dry Wire and picket fences can cause extra line wear or breakage Stone and brick walls curbs and wood may wear lines rapidly Avoid trees and shrubs Tree bark wood moldings siding and fence posts can easily be damaged by the lines 56V LITHIUM ION CORDLESS LINE TRIMMER 21 GO ADJUSTING CUTTING LINE LENGTH The bump head allows the operator to release more cutting line without stopping the motor As line becomes frayed or worn additional line can be released by lightly tapping the bump knob on the ground while operating the trimmer Fig 13 NOTICE Always keep the cutting line fully extended Line release beco
26. ring shipping Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool lf any parts are damaged or missing please return the product to the place of purchase 12 56V LITHIUM ION CORDLESS LINE TRIMMER MOUNTING THE GUARD WARNING Always wear gloves when mounting or replacing the guard Take care of the blade on the guard and protect your hand from cutting 1 Remove the battery pack from the trimmer N Position your trimmer so that the trimmer head faces up 3 Loosen and remove the two screws from the motor housing with a Phillips screwdriver available separately Fig 1 4 Align the ribs of the guard with the guide slots in the motor housing and push the guard in place Fig 2 5 Lock the guard with two screws Fig 3 56V LITHIUM ION CORDLESS LINE TRIMMER 13 GO MOUNTING AND ADJUSTING THE FRONT ASSIST HANDLE 1 Remove the battery pack from X the trimmer al W a Front Assist Handle I 7 r 2 Loosen the four screws in the 7 y handle with a Phillips screwdriver available separately and remove the screws spring washers flat washers and lower clamp from the handle Fig 4 2 3 Attach the front assist handle Lower Hamp and lower clamp on the shaft and secure them by pre tightening the four screws Turn the front assist handle upwards to point toward the top of the handle Fig 5
27. spool retainer and position the spool in the retainer Fig 20 24 56V LITHIUM ION CORDLESS LINE TRIMMER GO 9 Hold the spool and spool retainer grasp the line and pull it to release the line from the notch in the eyelet Fig 21 10 Check to see if the spring is properly located in the spool base If it comes loose or drops out position the spring in the mounting hole of the spool base and press it in place Fig 22 1 With the spool base facing downward align the tabs on the spool retainer with the slots in the spool base and press the retainer evenly down until it snaps into place Fig 23 NOTICE Make sure the spool retainer tabs snap into place or the spool will come out during operation 56V LITHIUM ION CORDLESS LINE TRIMMER 25 GO Install a pre wound spool A WARNING To prevent serious personal injury remove the battery pack from the tool before servicing cleaning changing attachments or removing material from the unit AX WARNING Always use only EGO authorized replacement nylon cutting line Using line other than specified may cause the line trimmer to overheat or be damaged 1 Press the release tabs on the spool retainer and remove the retainer by pulling it straight out Fig 16 Take out the spool Use a clean cloth to clean the inner surface of the spool base Check the spool retainer spool and spool base for
28. ther possible serious injuries AX WARNING Do not use any attachments or accessories not recommended by the manufacturer of this product The use of attachments or accessories not recommended can result in serious personal injury AX WARNING Use your line trimmer equipped with the appropriate cutting line only for cutting grass and similar material TO INSTALL REMOVE BATTERY PACK Fig 7 amp 8 A WARNING Always remove the battery pack from the product when you are assembling parts making adjustments cleaning or when not in use Removing the battery pack will prevent accidental starting that could cause serious personal injury NOTE Fully charge the battery pack before first use To install Fig 7 m Align the ribs of the battery pack with the mounting slots in the line trimmer s battery port Press the battery pack toward the cutting head until it snaps into position NOTE Make sure that the latch on the line trimmer snaps into place and the battery pack is secured to the tool before beginning operation Mounting Slot 56V LITHIUM ION CORDLESS LINE TRIMMER 1l GO To remove Fig 8 A WARNING Always take care of your feet and children or pets around you when pressing the battery release button oO Serious injury could result if the battery pack falls NEVER remove the battery pack at a high location Hold the battery pack in the palm of your hand Press the battery release button
Download Pdf Manuals
Related Search