17407 NA-NEX6 manual
Contents
1. of the housing is clean and free from foreign material Press and hold the port release safety button turn the port lock release latch clockwise for 60 until the circle mark on the latch aligns with the RELEASE index on the rear housing Lift the Port lock release latch Lift housing cap 6 Align the Port mounting indices of the port and the housing 7 Gently push the port into the port opening of the housing until it cannot go in any further 8 To lock the port in place turn the port lock release latch anti clockwise for 60 to the Lock position 9 Toremove the port from the housing repeat steps 3 and 4 then gently pull it out 15 Care and Maintanence 1 Soak the housing system in fresh water after each salt water use during which all control buttons knobs should be operated a few times to avoid the accumulation of salt residue wipe the housing with a towel before opening 2 After each day of diving it is advisable to have the main O ring in the rear part of the housing removed from its groove with the O ring remover and inspected for damage Also check that the O ring retains its original circular shape never stretch the O ring excessively or remove it with a sharp object The O ring groove should be cleaned to ensure it is free from any salt deposit or foreign material lightly coat the O ring with the provided lubricant before reinstalling it in the groove A damaged O r2. Nlauticam innovation underwater NA NEX6 Underwater Camera Housing Instruction manual Foreword Thank you for your purchase of a NAUTICAM camera housing At NAUTICAM we pride ourselves on the ability to recognise the requirements of professional as well as amateur underwater photographers and fulfill them through the innovative designs of our products We strive to achieve a high level of user friendliness by allowing stress free installation and easy operation of all important functions of the camera Each NA NEX6 housing is individually inspected and water pressure tested to ensure optimum quality Please read this manual carefully before using the housing this will maximise its performance as well as its lifetime Warranty 1 All NAUTICAM Products are warranted against any material and manufacturing defects for one year from the date of purchase for consumer use 2 NAUTICAM accepts no liability for any damage to and defects in the housing caused by improper use and or poor maintenance it is the responsibility of the owner to carefully follow the instructions in this manual 3 NAUTICAM does not hold responsibility for damage of any nature to any equipment used with and or placed within the housing 4 NAUTICAM accepts no liability for any loss of captured images or the inability to capture images even if it is due to the malfunctioning or leakage of the housing 5 This warranty only applies to products pur
3. chased from authorised NAUTICAM dealers and does not extend beyond the original retail purchaser 6 Unauthorised modifications and or repairs of the housing will automatically invalidate this warranty 7 Toreturn products for service please contact our regional distributor normally you would need to notify them by email first and ship them the product by registered mail along with your contact details and a brief description of the defect Package Contents i 2 3 4 5 6 yA NA NEX6 housing Instruction manual Spare silicone rubber housing o ring O ring remover CR2032 battery for moisture alarm Lubricant Set of Allen keys Slel Spare silicone rubber o ring O ring remover CR2032 battery Lubricant Set of Allen keys Precautions 10 11 A water tight test without the camera inside the housing is highly recommended when using the system for the first time and after the changing of port and O ring s Do not use lubricants from other brands with the silicone rubber O ring on this housing only use the lubricant provided by NAUTICAM Discontinue use immediately should you notice any leakage Store the housing in a robust shock proof container during transportation avoid transporting with any equipment such as a camera inside the housing When travelling by air do not close the housing if the port is installed as this may lead to a pressure difference between the atmosphere and insi
4. de the housing Care must be taken when opening the housing as pressure may build up inside the housing which increases the opening force Do not open the product in a wet or sandy environment Protect the interior from moisture and debris in order to prevent malfunction or leakage Do not store the product in an environment of high humidity Do not leave the housing and the camera in direct sunlight for prolonged periods Keep out of reach of children failure to do so could result in injury Defective products should be shipped to our distributors for service unauthorized disassembling and or modifications could result in malfunction or leakage Table of Contents Identification of Parts Opening and Locking the Housing Mounting the Port Optional Accessories Specifications Approx 0 93kg without camera slightly negative Allows the camera s built in flash to be disabled underwater Flash up off lever Moisture alarm Blinking LED and audible alarm Optical fibre mount included for TTL capability external strobes connec utilising the camera s pop up flash as trigger oct Patented easy port installation Features system Control dial Easily reached by thumb Identification of Parts 1 5 A co 6 3 7 TODD innovation underwater Tur port lock to release position for housing cap removal 10 Optical fibre mount Zoom Focus knob On off lever Port alignment
5. index Shutter release lever Port release safety button Lens release button Port lock release latch M16 accessory port 1 4 20UNC tripod socket x 2 The maximum length of screws that can be used with the tripod sockets is 4mm 19 on ur Zi Viewfinder LCD lever Control wheel Moisture alarm window Right selection ISO button Playback button Soft key C button SU seta Left selection Drive mode button Baier Down selection Exposure comp Image index button Soft key A button Soft key B button Preparation of the Housing 1 After verifying that the housing O ring is in good condition lightly coat it with the lubricant provided 2 Make sure the O ring groove located in the rear part of the housing is free from any foreign material the groove can be cleaned with the aid of a microfiber cloth 3 Place the O ring into the groove 4 To install the optical fibre mount for external strobe connection fasten it with the screws provided to the threaded sockets of the accessory coldshoe as shown 10 Setting up the moisture alarm 11 Install the CR2032 provided into the battery battery compartment on the circuit board inside the rear part of the housing Test the alarm by contacting the two wires near the bottom of the housing with a damped cotton bud the alarm should Start giving out a repeating beep sound along with a flashing red light The beep sound and the light sho
6. ing should be discarded immediately and replaced only with one that is provided by NAUTICAM 3 Replace the main O ring annually 4 It is recommended that you ship the housing to our distributor for a complete overhaul every year or after every 200 dives 16 Optional Accessories NAUTICAM International Limited Room 2203 CCT Telecom Building 11 Wo Shing Street Fotan HONG KONG Email enquiry nauticam com Tel 852 2690 2711 Fax 852 2690 9778
7. uld keep on going for 5 seconds after the removal of the damped cotton bud Opening and locking the housing To open the housing 1 Press the housing lock safety 2 Turn the housing lock anti button clockwise for 270 until the lock reaches the Open position as shown To lock the housing 3 Close the housing while the 4 Turn the housing lock clockwise housing lock is in the Open for 270 until the lock reaches the position lock position as shown Confirm that the white indicator line on the safety button is visible 12 Installing the Camera Disengage the red camera saddle 2 Tilt the LCD monitor of the camera lock by pressing it inwards upwards then attach the saddle to Remove the camera saddle from the camera by tightening the screw the housing by sliding it outwards to the tripod socket of the camera 3 Install the camera by sliding 4 Please make sure the eyepiece the attached saddle along the cup is not attached to the rail in the housing until it camera Confirm that the red cannot go in any further camera saddle lock is in the engaged position before closing the housing 13 Mounting the Port Please refer to the NAUTICAM system port chart for a range of compatible ports 1 Remove the O ring from the port inspect for any damage and lightly coat it with the provided lubricant before placing it back into its groove Verify that the port opening
Download Pdf Manuals
Related Search