USER`S MANUAL - PurifierParts.com!
Contents
1. 2 Level and place the LaundryPure to the wall marking where the two 2 keyholes are on each side with a pencil Drill two 2 holes in the wall where marked and place two 2 supplied anchors into the holes Place the two 2 supplied screws into anchors in the wall and tighten until almost all the way Move the keyholes of the LaundryPure onto the screws and finish tightening to secure to the wall 3 Reverse instructions located on page 10 to replace cover N CAUTION This appliance must be installed in a level horizontal configuration as shown Do not install the unit vertically or at an angle Failure to follow these instructions may prevent the internal moisture sensor from operating properly N CAUTION When connecting or disconnecting hoses hold the threaded connector on your LaundryPure with pliers while turning the hose connector Failure to follow these instructions may result in damage to your appliance NOTE Be sure rubber washers are properly inserted into hose connectors before installing hoses 4 Connect the end of the hose 5 Connect the new hose provided 6 Finally connect the new from your cold water valve with your LaundryPure to the hose to the cold water inlet to your LaundryPure s INLET water OUTLET connector on on your washing machine connector marked on front your LaundryPure unit of the LaundryPure LAUNDRY A LAUNDRY LA2. This system is designed for use on potable water systems only LOCATION CONSIDERATIONS It is recommended the LaundryPure never be installed in areas where water may freeze since the unit will always maintain some water in the unit the water valve and hose areas This can cause damage to internal components 9 375 238 13 mm 4 0 101mm WINDOW LAUNDRY PURE WATER WATER OUTLET INLET BEFORE YOU START 1 Remove your new LaundryPure from its packaging 2 Turn the cold water off by shutting off the cold Inspect for any shipping damages water valve NOTE Tohelp prevent water spray when disconnecting hoses you can relieve pressure in the water line by momentarily starting your washing machine N CAUTION Do not remove or disconnect the hot water line from your washing machine or water valve Turn off the hot water valve to prevent possible leakage Using the hot or warm water settings on your washing machine will reduce the effectiveness of your LaundryPure system AN WARNING Electrical Shock Hazard Disconnect power before attempting installation or 3 Remove the cold water hose from the cold water service Failure to follow these instructions can result inlet on the back of your washing machine in death fire or electrical shock INSTALLATION 1 Instructions to remove cover are located on page 9 Q
3. proper level To solve this problem the installation of a Y adaptor available at most hardware stores may be used The use of the Y adaptor allows water to flow equally through both the HOT and COLD water valves To install turn water off at the valves and disconnect the HOT water hose at the valve Connect the Y adaptor to the OUTLET on your LaundryPure then connect both the HOT and COLD hoses from your waster to the Y adaptor see diagram below Operate your water on the WARM WARM setting your LaundryPure will still be using just LAUNDRY PURE cold water N CAUTION When connecting or disconnecting hoses hold the threaded connector on your pliers winlle t the LaundryPure with pliers while HA turning the hose connector Failure to follow these instructions may result in damage to your Disconnect this hose from the OUTLET on your LaundryPure appliance then connect it to the Y adapter NOTE Your HOT water valve plumbing will NOT have a hose connected to it Make sure it is securely turned off Connect to COLD water inlet on washing machine Connect the Y adapter to the OUTLET on your LaundryPure Be sure to hold the fitting with N CAUTION Turn off both water valves hot and cold before disconnecting hoses Failure to follow these instructions may result in water leakage and or possible injury from hot water Connect t
4. LAUNDRY PURE BETTER FOR YOUR LAUNDRY BETTER FOR YOUR FAMILY BETTER FOR THE ENVIRONMENT TWO MODELS FOR e Standard Top Load Machines e HE Front Load LAUNDRY PURE USER S MANUAL 7 H vollara CAUTION Read manual carefully for proper use and operation USE COLD WATER ONLY OUTLET INLET A DISCONNECT POWER BEFORE SERVICING BE L vollara GENERAL INFORMATION Contents General Information 2 Use amp Safety Considerations 3 Installation Requirements 4 Cabinet Features 2 2 4 Before You Start 5 Installation gs ee dee a ak ee ek am es 6 Connecting Power 7 System Set Up 7 Before Washing Clothes 8 Using Your LaundryPure 8 Removing The Cover 9 Reinstalling The Cover 10 To Increase Water Pressure 11 Maintenance Procedures 12 Troubleshooting 12 Installation Problems 12 Frequently Asked Questions 13 Declaration of Conformity 14 Warranty Information 415 Please record the serial number of your LaundryPure by Vollara LLC Model Serial Please record the name
5. POWER IN socket located on the bottom of the LaundryPure 1 Return the LaundryPure cover to its original position fitting the bottom in place and tipping upward N CAUTION Do not use any AC DC adaptor other than the one LAUNDRY PURE supplied with your LaundryPure or Vollara C replacement cord item US71157 Failure to follow these instructions may void your warranty and or result in damage to your unit fire or electrical shock DISCONNECT POWER BEFORE SERVICING 2 Secure with two 2 screws along the top edge LAUNDRY PURE 5 Turn on the cold water valve Start your washer 3 Put the two 2 remaining screws along the bottom and check the system for leaks edge and tighten AN WARNING Electrical Shock Hazard Electrical Shock Hazard Do no use an extension cord Do not operate with cover removed When working Failure to follow these instructions can result in death with electrical connections the appliance and fire or electrical shock surrounding area should be clean and dry of any standing water Failure to follow these instructions can result in death fire or electrical shock TO INCREASE WATER PRESSURE Some washing machine models require water to flow through both the HOT and COLD valves for proper operation In some cases if only the COLD water side is connected the water valve will not operate or the washing machine will not fill to the
6. UNDRY PURE PURE j PURE Hold with pliers Hold with pliers i J while installing hose in order to prevent fitting from rotating while installing hose in order to CONNECTING POWER N CAUTION Do not use any AC DC adaptor other than the one supplied with your LaundryPure or Vollara replacement cord item US71157 Failure to follow these instructions may void your warranty and or result in damage to your unit fire or electrical shock AN WARNING Electrical Shock Hazard When working with electrical connections the 1 Insert the provided power cord into the POWER IN socket located on the back of the unit The AC DC adaptor ee eae appliance and surrounding area should be clean and worldwide The dry of any standing water electrical plug may be Failure to follow these instructions can result in death removed and other fire or electrical shock AN WARNING Electrical Shock Hazard 2 Plug the opposite end of the provided power cord Do no use an extension cord Failure to follow these instructions can result in types added depending on the country electrical requirements into the wall outlet of your home s electrical power system See page 4 for electrical requirements death fire or electrical shock SYSTEM SET UP _ pager Pree A Z3 CA ir Oo 3 Start your washer The stat
7. and phone of your Independent Vollara Business Owner Name Phone SPECIFICATIONS AC DC Adaptor e AC in 100 240V 50 60 Hz 0 8A e DC out 12V SS 2 5A Power Consumption e 7 5W standby mode e 25W operating Water Pressure e Minimum 10 psi to 75 psi maximum Water Temperature e Use cold water only do not use hot water Operating Environment Temperature 50 F 100 F 10 C 378 C Dimensions 18 25 in x 9 375 in x 4 0 in 463 55 mm x 238 13 mm x 101 6 mm Weight e 7 55 pounds e 3 42 kg Dissolved Oxygen Concentration e 0 18 mg L or 0 18 ppm 180 ppb Product Overview LaundryPure is designed to work in conjunction with your washing machine using cold water and ActivePure to clean clothes As your washer begins to fill LaundryPure will turn on LaundryPure is equipped with an internal leak sensor See page 12 for more details USE amp SAFETY CONSIDERATIONS Do not operate unit with cover removed Disconnect all power before servicing Do not use an extension cord or other adapter with this appliance This appliance is not recommended for use with high iron content water If your water has a high iron content consult a water filtration expert for available options Maximum water inlet pressure is 75psi Use the included new hose when connecting the LaundryPure unit to your washing machine You should replace any washing machine hose that is more than 2 years
8. cation commercial use or by any repairs other than those provided by our authorized Service Center This warranty is non transferable MISSING SERIAL NUMBERS AND UNAUTHORIZED CHANNELS If a valid serial number is missing from the product the warranty will be voided Vollara products are authorized for sale through Vollara Independent Business Owners only Warranties are voided if a product is purchased through unauthorized channels this includes websites that are not authorized to use Vollara s trademarked names images and logos as well as Internet auction sites e g ebay and Craigslist The only approved Internet presence for Vollara products is www vollara com To confirm SERVICE warranty coverage prior to purchasing a product contact Vollara at 800 989 2299 with the serial number located on the back of the unit EXCLUSION OF OTHER WARRANTIES AND CONDITIONS EXCEPT AS PROVIDED HEREIN WE MAKE NO REPRESENTATION OR WARRANTY OF ANY KIND ALL OTHER WARRANTIES OF ANY KIND EXPRESS OR IMPLIED ARE HEREBY EXPRESSLY DISCLAIMED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE LIMITATION OF LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WE SHALL NOT IN ANY CASE BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM BREACH OF EXPRESSED OR IMPLIED WARRANTIES CONDITIONS GUARANTEES OR REPRESENTATIONS BREACH OF CONTRACT NEGLIGENCE OR ANY OTHER LEGAL THEORY Such ex
9. cluded damages include but are not limited to loss of profits or revenue and loss of the use of the products and any loss caused by leaks or other water damage FOR U S APPLICATION ONLY This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow limitations on warranties or on remedies for breach In such states the above limitations may not apply to you FOR CANADIAN APPLICATION ONLY Exclusion of Subsequent Owners Except as otherwise required by applicable legislation this warranty is not transferable This warranty gives you specific legal rights and you may also have other rights which vary from province to province Some provinces and territories do not allow limitations on warranties or on remedies for breach In such provinces or territories the above limitations may not apply to you If any provision of this warranty or part thereof is held by a court of competent jurisdiction to be invalid illegal or unenforceable the validity legality and enforceability of the remaining provisions or parts thereof will not in any way be affected or impaired within the jurisdiction of that court This entire warranty shall continue to be valid legal and enforceable in any jurisdiction where a similar determination has not been made This warranty is provided by Vollara LLC 5420 LBJ Freeway Suite 1010 Dallas TX 75240 Every effort is made to en
10. fer to have a plumber perform the installation although LaundryPure can be installed in most homes by the home owner using standard hand tools It should be noted there are potential problems which can arise during the installation depending on the condition of the plumbing in the home and the configuration and location of the washer If the cold water valve is stuck or the washing machine needs to be moved back which may require releveling a plumber may be required Vollara LLC is not liable for improper installation or damage caused from improper installation Appropriate warnings and concerns are included in this owner s manual What will need to be replaced on the LaundryPure There is nothing to replace inside the LaundryPure unit Can hook the LaundryPure unit up to things other than a washing machine LaundryPure is designed to work with residential washing machines only Use for any other purpose may void your warranty What effect does LaundryPure have on elastic Normal operation of a LaundryPure unit should have no negative impact on elastic in clothing Can let my clothes soak overnight It is not recommended that clothes are allowed to soak overnight in LaundryPure water CE DECLARATION OF CONFORMITY We Vollara LLC 5420 LBJ Freeway Suite 1010 Dallas TX 75240 Declare under our sole responsibility that the Electronic Purification System Model LaundryPure to which this declaration relates confor
11. ic mixer light warm blue glow should come on and you should see water begin to flow when looking through the view window 1 Turn on the cold water valve U e a NOTE Your LaundryPure should automatically turn on and off when your washing machine starts and stops 2 Check all hoses to ensure no water is leaking Tighten if necessary BEFORE WASHING CLOTHES BEFORE USING YOUR LAUNDRYPURE FOR THE FIRST TIME IF YOUR WASHING MACHINE IS NEW skip this section LAUNDRY and continue below gt IF YOUR WASHING MACHINE IS NOT NEW you will need to perform this procedure to help remove any detergent buildup that may contaminate your clothing 1 Do not put clothes in the washer at this time Set your machine to its largest load setting cold water only 2 Start the washer and let it run through every cycle 3 Once it has finished repeat Steps 1 and 2 three more times N CAUTION To avoid the possibility of water damage should a hose leak always have faucets accessible and turn off faucets when washer is not in use Depending on the age and severity of detergent buildup in your machine it may be necessary to perform Step 3 more than once USING YOUR LAUNDRYPURE coun wor NORMAL OPERATION Using your LaundryPure is as simple as turning on the washing machine LaundryPure is designed to use only the COLD COLD setting of your wash
12. ing machine DETERGENT AND FABRIC SOFTENER You may choose to continue to use detergent and or fabric softeners if desired However to completely experience all the benefits of your new LaundryPure we recommend washing using nothing but cold water HEAVY STAINS For heavy stains pre treat area apply detergent rub gently and let stand for several minutes Wash as normal REMOVING THE COVER A WARNING LAUNDRY Electrical Shock Hazard Disconnect power before attempting installation or service Failure to follow these instructions can result in death fire or electrical shock 4 Remove the two 2 cover screws located on the i C bottom of the unit LAUNDRY PURE 1 Turn off the cold water valve 1 DISCONNECT POWER BEFORE SERVICING USECOLDWATERONLY OUTLET Y LET 5 Remove the two 2 screws along the top of the LaundryPure PU 2 Briefly turn washer to the ON position This will allow the water to drain from the LaundryPure unit Turn the washer OFF DISCONNECT POWER BEFORE SERVICING POWER IN 6 To remove the cover pull the top away from the unit then lift off the cover m 3 Unplug the unit by removing the power cord from the POWER IN socket on the LaundryPure REINSTALLING THE COVER POWER IN l z 4 Return the power cord to the
13. ions N CAUTION Damage to your appliance or the surrounding area can occur if you don t follow instructions NOTE This information is included to aid in installation and use of this appliance INSTALLATION REQUIREMENTS ELECTRICAL REQUIREMENTS 100 240 Volt 50 60 Hz 5 AMP minimum Fuse or Circuit Breaker LaundryPure is equipped with an AC to DC power supply NEVER USE AN EXTENSION CORD As with most major appliances use of a GFI Ground Fault Circuit Interrupt is not recommended WATER REQUIREMENTS Water pressure of 10 to 75 psi is required to correctly operate your LaundryPure Low water pressure may prevent your unit from operating properly and or cause a failure in your washing machine s water valve The washer s water valve may also not shut off completely Check the documentation supplied with your washing machine for exact specifications CABINET FEATURES Your washing machine and cold water faucet must be within 4 feet of the right side of the unit to use the inlet hose provided with your LaundryPure TO AVOID THE POSSIBILITY OF WATER DAMAGE SHOULD A HOSE LEAK ALWAYS HAVE FAUCETS ACCESSIBLE AND TURN OFF FAUCETS WHEN WASHER IS NOT IN USE Water quality may affect the performance of your LaundryPure unit If you have water quality concerns such as high iron content or high chlorine content consult a water filtration expert
14. ms with the following standards EN55014 1 EMC Requirements for Household Appliances and Similar Apparatus Emissions EN50014 2 EMC Requirements for Household Appliances and Similar Apparatus Immunity EN60950 1 2001 11 2004 Safety of Information Technology Equipment General Requirements By conformance with the standards reference the product meets the provisions of the EU Directives listed below Low Voltage Directive 2006 95 EC applies to power supply only EMC Directive 2004 108 EC RoHS Directive 2002 95 EC WEEE Directive 2002 96 EC Authorized by Tee Eal Company Vollara LLC 5420 LBJ Freeway Suite 1010 Representative Andy Eide Dallas TX 75240 Title Vice President of Advanced Development and Research U S A Date January 10 2010 FCC DECLARATION OF CONFORMITY This equipment has been tested and found to comply with the limits for Industrial Scientific and Medical Equipment Name Vollara LLC ISM pursuant to Part 18 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions This device complies with Part 18 of the FCC Rules may cause harmful interference to radio communications However there is no guarantee that interference will not RESPONSIBLE PARTY occur in a particular installation If this equipme
15. nt does KE cause harmful interference to radio or television which can VO aro be determined by turning the equipment off and on the user Vollara LLC is encouraged to try to correct the interference by one or more of the following measures 5420 LBJ Freeway Suite 1010 x Dallas TX 75240 Reorient or relocate the receiving antenna Model LaundryPure Manufacturer Vollara LLC Ph 800 989 2299 Increase the separation between the equipment and receiver Signature SS A Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Printed Name Andy Eide Title Vice President Product Development amp Research Date January 10 2010 Consult the Dealer or an experienced radio TV technician for help LIMITED ONE 1 YEAR WARRANTY Customer should not repackage and ship the LaundryPure unit due to possibility of irreparable damage For warranty service please contact your Independent Distributor for the address of the nearest service center LIMITED ONE 1 YEAR WARRANTY Customer should not repackage and ship the LaundryPure unit due to possibility of irreparable damage For warranty service please contact Vollara Customer Service at 800 989 2299 or your Vollara Independent Business Owner for the address of the nearest service center WHAT IS COVERED BY THIS WARRANTY We warrant the LaundryPure to the Customer subject to the conditions bel
16. o household plumbing COLD water valve Y adapter Make sure the y adapter valve is in the on position Disconnect this hose from the HOT valve then connect it to the Y adapter Connect to HOT water inlet on washing machine 11 MAINTENANCE NO USER MAINTENANCE REQUIRED There are no user serviceable parts inside this a f product If a problem with unit is detected the warm blue glow will turn bright red If a leak is detected ill al Son ie oe ie as eee age Nee e Electrical Shock Hazard Disconnect power before mae attempting installation or service If this occurs please contact Customer Service e Electrical Shock Hazard When working with at 800 989 2299 electrical connections the appliance and surrounding area should be clean and dry of any standing water Failure to follow these instructions can result in death fire or electrical shock LAUNDRY PURE e Do not operate LaundryPure with the UV shield or front cover removed or improperly installed ie Failure to follow these instructions can result in vollarar severe eye damage death or electrical shock DISCONNECT POWER BEFORE SERVICING TROUBLESHOOTING 1 The LED lights are on in the unit but there is no Check your inlet and outlet connection to make water flow bubbles sure the hose connections are not reversed Make sure y
17. old To prevent leaks do not leave your hot water hose disconnected Do not clean your LaundryPure with harsh chemicals abrasives or cleansers Use a soft cloth dampened with water Do not mount the LaundryPure unit vertically or at an angle Improper mounting may not allow the unit to function properly and void your warranty See page 6 for correct mounting instructions LaundryPure is designed for residential use only Use in a commercial or non residential setting may void your warranty Water treated by your LaundryPure unit is intended for clothes washing only and is not approved for consumption Do not drink or ingest the water from your LaundryPure unit or washing machine IMPORTANT SAFETY PRECAUTIONS To prevent unnecessary risk of fire electrical shock or personal injury all wiring must be done in accordance with the National Electrical Code ANSI FNPA No 70 Latest Revision and local codes and ordinances It is the personal responsibility and obligation of the appliance owner to provide adequate electrical service for this appliance We have provided important safety warnings in this manual and on your appliance Always read and obey all safety messages Safety warnings in this manual are defined as follows A DANGER Death or serious injury can occur if instructions are not followed immediately J WARNING Electrical shock hazard You can be killed or seriously injured if you don t follow instruct
18. our washing machine is set to the cold water setting 4 No water is processing through the system Make sure that your cold water is turned on at your Check the power connection supply valve 5 Ared light visible thru the window 2 No power Contact your Independent Vollara Business Owner Check your electrical connections and make sure they re all fully seated 6 The red light is blinking and a buzzer sounds 5 No bubbles are visible bei window and Contact your Independent Vollara Business Owner no or very little water flow INSTALLATION PROBLEMS Installation procedures can vary according to washing machine model If you experience installation problems visit www vollara com LaundryPure for more information FREQUENTLY ASKED QUESTIONS Does LaundryPure get out tough stains without pretreating Tough stains will still require pretreatment Does the LaundryPure work with all types of water including hard water LaundryPure will work with all household water qualities but the better the incoming water quality the better the results you will have To improve your results if desired use a water softener for hard water and or a prefilter for chlorine Will the LaundryPure work with Commercial Washing Machines LaundryPure is designed for residential use only Is a Plumber required to install LaundryPure The customer is responsible for installation of their LaundryPure unit Some customers may pre
19. ow against defects in workmanship or material provided that the products are returned to a service location within one 1 year from the date of purchase INSTALLATION AND MAINTENANCE REQUIREMENTS This warranty is expressly conditioned upon proper installation operation cleaning and maintence all in accordance with the Owner s Manual Failure to meet any of these requirements will void this warranty Servicing of your LaundryPure by parties other than our authorized representatives and or using parts other than genuine parts will also void this warranty HOW TO OBTAIN WARRANTY SERVICE Customer must contact Vollara Customer Service and provide proof of purchase within the above time period We will repair or replace and return the product without charge and within a reasonable period of time subject to the conditions herein if its examination shall disclose any part to be defective in workmanship or material If we in our discretion are unable to repair the product after a reasonable number of attempts we will provide either a refund of the purchase price or a replacement unit at the company s option WHAT IS NOT COVERED BY THIS WARRANTY This product is intended for household use only Ordinary wear and tear shall not be considered a defect in workmanship or material These warranties do not apply to filters nor for loss or damage caused by accident fire abuse misuse improper installation leaking modification misappli
20. sure customers receive an up to date instructions manual on the use of our products however from time to time modifications to our products may without notice make the information contained herein subject to alteration For the latest information please visit our web site 15 65 00313 LP_OM_65 00313 0110 s L vollara Vollara LLC 5420 LBJ Freeway Suite1010 Dallas TX 75240 800 989 2299 I A A Vollara LLC All Rights Reserved
Download Pdf Manuals
Related Search