BGAN Enclosure for Explorer 300 and Explorer 500
Contents
1. yp Thrane amp Thrane Doan Inmarsat scans man oS oe BI HE i i i H i a i H DASHBOARD PORE ME IR O O PHONE BOOK Pointing required at power up Yes No i MESSAGES The terminal will switch on when external power is connected Yes O No CALLS BACKLIGHT SETTINGS Timed Always off V i epi Set level LAN CONTRAST i Bluetooth Automatic Oves O No H H Phone Fax Set level i Common AUDIO INDICATORS i Advanced wat Pointing Gon off i Language 4 i Messages PROPERTIES a O zi on i ADMINISTRATION Alarm on O off i i HELPDESK STEALTH MODE i B SITE MAP Stealth Enable O Disable i Click on the Apply button to save the new settings Bluetooth can be disabled if not used found under SETTINGS INTERFACES ATTENTION Do not disable the LAN interface as this is the only means of re establishing the configuration besides connecting via Bluetooth or having to open the enclosure and changing it back using the keypad When the installation and configuration is successfully completed remember to mount the front cover on the enclosure If the instructions are followed step by step then it will take approximately 15 min to do the installation and configuration Information in this document is subject to change without notice and does not represent a commitment on the part of Thrane amp Thrane A S 2007 Thrane amp Thrane A S All rights reserv2. ft away from the enclosure With the EXPLORER 300 the range is up to 25m 82 ft A heating module with built in automatic temperature sensor is available as an option Please note that the installation procedure will differ slightly from the one described in this document OUTDOOR INDOOR Features and specifications IP67 6 Totally protected from dust 7 Protected from the effects of immersion between 15cm amp 1m Overall size of enclosure H x W x D 250 x 400 x 125 mm 9 8 x 15 7 x 4 92 in Complete and pre assembled enclosure no cutting or drilling necessary No degradation of throughput or GPS time to fix Breakout box with Ethernet RJ 45 2 wire Phone or Fax RJ 11 and DC input Accredited Solution EXPLORER CPN Enclosure Page 2 6 Thrane amp Thrane Pole mount kit with adjustable elevation angle included for easy installation Single cable between enclosure and breakout box available in lengths of 10 m 32 ft 25 m 82 ft 50 m 164 ft and 75 m 246 ft Rounded edges minimal protrusions or exposed pocket areas for accumulation of dust or debris Optional built in heating system specified down to 55 C 67 F Color of enclosure White E mail mailto info cpn de Phone 49 6722 93728 0 Web site http www cpn de E mail mailto solutions Qthrane com Phone 45 3955 8800 Web http www thrane com EXPLORER 300 Software version 2 03 EXPLORER 500 Software version 2 03 Use the built in compass
3. in the EXPLORER terminal and the Inmarsat BGAN coverage map found in the User Manual to get a rough indication of the direction of the satellite before choosing where to mount the enclosure Make sure that when the EXPLORER terminal is mounted inside the enclosure the directional antenna has a clear line of sight to the satellite and is not blocked by objects like buildings trees passing cars etc If the EXPLORER terminal will be switched OFF from time to time it will speed up the GPS time to first fix if it is placed in an open area with a clear view to the sky The enclosure must be located such that during transmission no person can come closer than the minimum safe distance to the front of the antenna of 60 cm 24 inches Once a suitable location has been determined switch ON the EXPLORER terminal and fine adjust its position for best possible signal strength reception Be careful not to block the received satellite signal does not transmit when in Pointing mode Please refer to User Manual for further instructions When in the right position make a note of the C No value shown in the EXPLORER terminal display Now adjust the enclosure accordingly to match the exact pointing direction and elevation angle of the EXPLORER terminal You may now switch OFF the EXPLORER terminal Depending on the application you may want to remove the battery in the EXPLORER terminal so it will be possible to power the EXPLORER terminal ON and OFF from the Br
4. to the DC input of the terminal as shown in the picture to the right Step 5 Calibrate the elevation to get the most optimal signal strength then tighten the two bolts firmly to make sure the elevation will not change in harsh weather conditions This is a good time to check that the terminal is pointing in the best possible direction The EXPLORER 300 display is still visible so it is possible to go in to pointing mode and made the final calibrations to both direction and elevation If installing an EXPLORER 500 then use the built in web server to check the signal strength The better signal strength the EXPLORER terminal has the higher data throughput it will offer and the less power it will use and thereby also generating less heat Step 6 Before mounting the front cover on the enclosure it may be a good idea to verify that it indicates the same C No value as noted earlier and to make a quick test phone call on the RJ 11 see User Manual and connect to the built in web server in the EXPLORER terminal as explained below this step by step installation guide DA Step 6 continues on next page Figure G Accredited Solution EXPLORER CPN Enclosure Page 4 6 Thrane amp Thrane Secure the lid on the front to the CPN enclosure with a screw in each corner Make sure that the there are no dirt on the seal when the screws are tightened This might break or damage the seal and thereby not granting the full p
5. 05430510 Standard data 562 75 MB ADMINISTRATION Software version 2 03 build EXP 2 03F 7 Streaming 32 kbps 00 00 00 HELPDESK Local IP address 192 168 0 1 Streaming 64 kbps 00 00 00 SITE MAP IMEI number 35315000 001029 4 Streaming 128 kbps 00 03 01 MAC address 00 11 CF 00 A2 A7 ONGOING DATA SESSIONS ONGOING CALLS Standard data 161 30 180 147 Standard valce 00 02 45 STREAMING PROFILES ON LAN Start Streaming 32 Start Streaming 64 Start Streamina 128 Click on Go to pointing mode and verify that it indicates the C No value as expected If the C No is as expected click on Accept signal strength if not then make the necessary Accredited Solution EXPLORER CPN Enclosure Page 5 6 Thrane Thrane adjustments to the enclosure As a help use the built in audio indication for pointing of the antenna enclosure Having already successtully pointed the antenna you should configure the terminal to automatically skip pointing at power up by clicking No to Pointing required at power up This can be configured under SETTINGS Also set the terminal to switch ON when power is applied to the Breakout box by clicking the Yes button for The terminal will switch on when external power is connected Please refer to picture below example with EXPLORER 500 nan dana noon aaa anana nan bantran noon aaa nana kann aaa ennan anan atann pannan anan aaa anana anan a anan saaa anana aaa onon annan ane n rann anan annan tann
6. Thrane amp Thrane Thrane amp Thrane A S Lundtoftegaardsvej 93 D DK 2800 Kgs Lyngby Denmark PYY T 45 39 55 88 00 F 45 39 55 88 88 info thrane com www thrane com inmarsat Thrane amp Thrane EXPLORER CPN Enclosure Revision G This document describes step by step how to mount the enclosure from CPN Satellite Services GmbH and how to install and configure the EXPLORER 300 and the EXPLORER 500 terminal Data Acquisition M2M Remote work sites Aid Disaster Relief or any other fixed or semi fixed outdoor installation The enclosure is a non metallic enclosure that is specifically designed to accommodate the EXPLORER 500 terminal Since the EXPLORER 300 is physically smaller than the EXPLORER 500 terminal the EXPLORER 300 terminal is also easily fitted in the enclosure When mounted inside the Ingress Protection 67 enclosure the EXPLORER terminal can be installed outdoors permanently in any weather condition The enclosure and the EXPLORER terminal is the ideal solution for instance as a satellite back up emergency system or for transferring data or video from a remote site The enclosure can be installed up to 75 m away from your wired wireless router switch computers surveillance camera PABX phone and or fax etc The Breakout box offers a DC input a Phone Fax interface RJ 11 and LAN interface With the EXPLORER 500 wireless voice and data connections will be available in a range of up to 100 m 328
7. eakout box by simply applying removing the power Remove the four screws holding the front cover and the screws that hold the sub panel The EXPLORER terminal is mounted to the sub panel using the included M6 screw that fits into the mounting bush in the back of the EXPLORER terminal Please refer to the step by step guide below for mounting the EXPLORER terminal in the correct position Step 1 Use the specially designed brackets to attach the CPN enclosure to a pole or railing Tighten all four bolts egually but make sure not to tighten them too hard this might damage the aluminium brackets Furthermore make sure that the CPN enclosure is pointing in the direction where the best possible signal strength is obtained which is found by following the instructions above Figure 1 Accredited Solution EXPLORER CPN Enclosure Page 3 6 Thrane amp Thrane Step 2 Mount the EXPLORER terminal on the aluminium sub panel with the supplied screw The screw goes through the panel into the back of the EXPLORER terminal A washer should be placed between the screw and the aluminium plate Step 3 Mount the aluminium panel with the EXPLORER terminal in the CPN enclosure with the supplied screws Make sure that the cables are not behind the aluminium panel when tightening the screws Step 4 Connect the Ethernet RJ 45 to the LAN connector on the EXPLORER terminal then the RJ 11 to the Phone Fax and finally the power plug
8. ed Printed in Denmark Accredited Solution EXPLORER CPN Enclosure Page 6 6
9. rotection to the EXPLORER terminal Step 7 Connect and secure the main multi plug located on the outside of the enclosure so it is tight and thereby hindering water and dust from penetrating The installation of the EXPLORER terminal into the CPN enclosure has now been completed Step 8 Pull the cable from the CPN enclosure into the office or building where access to the terminal needs to be and connect the power supply Ethernet and RJ11 cable to the connection box Your terminal is now safely located outside while you have full access to the terminal from inside your office or where ever you please to pull the cable with the connection box to Figure 8 To connect to the built in web server simply connect a computer to the Ethernet interface of the Breakout box Switch ON the EXPLORER terminal by connecting the EXPLORER terminal Power Supply to the DC input of the Breakout box Power up your computer Start up the Internet Explorer and type hitp 192 168 0 1 to get into the built in web server in the EXPLORER terminal as shown below example with EXPLORER 500 NA Z bgan inmarsat m man F se BT A DASHBOARD NETWORK SESSIONS TOTAL PHONE BOOK Airtime provider BETA TEST DATA Standard voice inbound 00 00 11 MESSAGES TERMINAL Standard voice outbound 00 12 30 CALLS Status Data active 3 1 kHz audio inbound 00 00 00 SETTINGS Pointing Go to pointing mode 3 1 kHz audio outbound 00 00 00 PROPERTIES Unit serial number
Download Pdf Manuals
Related Search