User guide Billi B-4000 Tap options XL, XT, XR
Contents
1. Orange mE A SES E Orange mmm X X o Unit in fault mode User guide Billi B 4000 XL XT XR Billi Filter Cartridges The Bill B 4000 is fitted with single dual action filter incorporating sediment and chemical removal elements All Billi B 4000 ilters are manufactured using bacteria and biofilm resistant materials for improved water quality Premium filters provide better tasting water due to the high quality carbon chemical removal filter Sub micron rated hese filters have excellent chemical absorption removing or reducing chlorine volatile organic compounds VOCs chemicals astes and odours Use only genuine filters as designed for this system All drinking water filtration systems should be flushed after a period of non use If your Billi B 4000 has not been used for a period of 48 hours or more flush for one minute Replacement of Billi Filter Cartridge Periodic replacement of your Bill B 4000 Filter Cartridge is necessary to maintain he cleanliness of your drinking water Billi recommends a filter replacement every 6 months or sooner if necessary Depending on mains water supply quality A replacement ilter change service is available If you wish o install the replacement filter cartridges yourself your Billi representative will provide genuine Billi replacement filter cartridge sets Billi Filter Cartridges Re2. O Red i lt Normal operation Normal operation Red eee SO erating temperatures of hot and cold water not Blue mom EO EEE yet reached Red Blue Boiling water disabled Blue System in holiday or standby mode or off Orange mE Orange mem X 8 AA 8 X o O Red O O Unit in fault mode User guide Billi B 4000 XR Dispenser Icon codes Dispenser Icon Orange dot Flashes when filter change due On constant when overdue Red lock illuminated Safety button activated To use press the indent on the op of the tap momentarily amp press the boiling button left Green leaf illuminated Eco intelligence Green moon amp stars illuminated n holiday mode or off Green moon amp stars flashing n stand by mode Red ring Flashes when heating up to temperature On constant when boiling water ready Off when in holiday standby or boiling water disabled Blue ring On constantly to indicate filtered water Red amp blue rings will flash yellow if the unit goes into fault O Red E Normal operation _ Normal operation Red See perating temperatures of hot and cold water not Blue uum EE NEED mm NEM yet reached Red Blue Boiling water disabled Red Blue System in holiday or standby mode or off
3. the products acting at Billi s direction or g if the product is altered or modified in any way unless such modification has been approved in writing by Billi 2 Notwithstanding anything to the contrary filters are not covered by this or any other Product Warranty b C d 13 User guide Billi B 4000 XL XT XR Limitation of liability 3 Except for the Product Warranty set out above and in connection with the supply of goods imposed on Bi Act 1974 Cth and other similar state and territory legislation including for breach of implied conditions and warranties which cannot or which can only to a limited ex of to ent be lawf he supply o except for any liability li by the Trade Practices ully excluded all liability and conditions and warranties relating the products by Billi are hereby expressly excluded Any such liability which cannot be lawfully excluded is limited at Billi S option to any one or more of the following a b C d 14 supply of eq he repair of he replacement of the goods or the uivalent goods the goods he payment of the cost of replacing the goods or of acquiring equivalent goods or he payment of the cost of having the goods repaired Billi Pty Ltd 42 Lucknow Crescent Thomastown Victoria 3074 Australia Telephone 61 3 9469 0400 Facsimile 61 3 9469 0499 www billi com au Designed and manufactured in Aust
4. 0 XL Options amp Operation To operate simply press the left lever to dispense boiling water and the right lever to dispense ambient When lifted the levers will latch for continual delivery until released with a light press Operating modes can be selected by the user by entering Options Mode Within the options mode you can set the safety switch through the hot water lever and power save mode through the cold water lever See below for further instructions To enter the options mode 1 Turn on the unit and wait for normal operation icons are both illuminated constantly 2 Push both the hot and cold levers down amp then while holding the two evers down press the safety switch at rear of tap Hold both levers and safety switch for 3 seconds Icons will flash yellow Release both the levers amp safety switch Unit is now in options mode anor C If you wish to change or set the safety Switch mode follow the safety switch settings procedure below If you wish o change or activate the power saving mode follow the power save mode settings procedure below Safety Switch settings The Red padlock indicates the different safety settings enabled To change or activate a setting once in options mode as above press and release the hot left lever to scroll through the following options Red Icon Off indicates the hot tap is disabled Padlock icon on Red icon on indica
5. Billi HOME User guide Billi B 4000 Tap options XL XT XR User guide Billi B 4000 XL XT XR Contents Warnings amp Important information 2 Warnings amp Important information For continued safety of this appliance it must be installed operated and maintained General Maintenance 3 in accordance with the manufacturer s Features and Modes 4 instructions Options amp Operation Your appliance should be installed XL Tap 5 by a suitably qualified tradesperson XI XR Tap 6 For correct operation of this appliance Dispenser Icon Codes 7 it is essential to observe the instructions XL Tap 7 as outlined in this booklet XT Tap 8 Do not use this appliance with water that XR Tap 9 is microbiologically unsafe or with water Filtration Information 10 of unknown quality without adequate Changing the filter 11 disinfection before or after the system Systems certified for cyst reduction may Service Support 12 be used on disinfected water that may Warranty 13 contain filterable cysts Filter replacement must be performed at intervals of not more than 6 months Use this appliance only as directed in these instructions and only for its designed purpose This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the
6. Centre on 1800 812 321 or book online at www billi com au Service Centre Filter cartridges are also available for purchase online at www billi com au Buy Filters User guide Billi B 4000 XL XT XR Warranty Subject to the warranty exclusions set out below if a defect in a new product supplied by Billi Pty Ltd ACN 124 066 717 Billi and purchased by you customer from a reseller authorised by Billi occurs within 24 months of the date of purchase of the product as a result of defective materials or defective manufacture by Billi and Billi receives a written claim containing details of the product defect together with a receipt from the reseller of the products showing the date of purchase of the products or such other proof of purchase and the date of purchase as Billi may accept within 25 months of the date of purchase Billi shall at its discretion a direct an accredited service provider to attend the customer s premises provided that the premises are located within Australia and repair the defect free of charge but if the customer s premises are located more than 25 kilometres from one of Billi s authorised service agent s locations then the customer will be liable for any increased freight costs fees charges or levies Billi may incur as a result of fulfilling its obligations under this paragraph a of this Product Warranty or b direct the customer to return the product to Billi so that B
7. In standby mode the hot water set point is reduced to 72 C and the cold water set point is increased to 18 C When enabled standby is invoked after two hours from the time of last use When a tap lever is pressed in standby no water is dispensed The indicators will flash to indicate the water is not ready The tap can be repressed to dispense water During Standby mode the Moon amp Star icons will flash to activate refer to Options page 5 Boiling water disabled mode Your Billi B 4000 features an additional boiling water safety isolation feature Once activated delivery of boiling water becomes totally disabled Chilled water can be dispensed normally During this mode the hot red icon will remain off To activate refer to Options amp Operation Safety Switch Settings on page 5 Holiday mode Holiday Mode is provided to save energy when the unit will not be used for long periods In this mode both the water chiller and water heater are disabled and the unit will use very little power Pressing the Pressure Relief button places the unit in Holiday Mode The unit will exit Holiday Mode if either the power is turned off then on or if any of the tap levers are pressed The Self Learning Timer will ignore user behaviour while the unit is in Holiday Mode and resume normal operation when the mode is terminated Holiday Mode is indicated the moon and star icon see page 6 for icon codes User guide Billi B 400
8. andled with caution Use this appliance only as directed in these instructions and only for the purpose for which it has been designed Your Billi B 4000 is designed to be safe and practical In an environment with young children it is recommended that the boiling water safety switch is activated The following safety features have been included Ergonomic levers Levers touch activations located safely above water outlet Smooth electronically controlled boiling water flow rate Flow is briefly reduced as water first enters cup to prevent splashing Dispenser remains cool to touch Childproof safety switch Boiling water Safety Isolation mode General Maintenance Your Billi B 4000 has been designed to require minimal maintenance other than replacement of filter cartridges During each filter change check all water connection fittings for signs of leakage Check all tubing for any signs of damage Check the cupboard area around the base of unit for any signs of moisture Ensure side vents of the under bench module are kept clear and airflow is not obstructed Restricted airflow will cause inefficient operation of the refrigeration system Cleaning the dispenser Your Billi B 4000 Dispenser is fabricated from robust metal with a tough protect chrome plating Care of dispenser is as with any chrome plated tapware Avoid using abrasive cleaners Wipe clean using a damp cloth Use of a non solvent n
9. appliance by a person responsible for their safety This appliance is not suitable in an area where a water jet could be used Children should be supervised to ensure that they do not play with the appliance DANGER The operation of the thermal cut out indicates a possibly dangerous situation Do not reset the thermal cut out until the water heater has been serviced by a suitably qualified person WARNING Do not connect any restrictor or pressure relief device to the vent pipe of this water heater if installed User guide Billi B 4000 XL XT XR f the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid creation of a hazard Billi hose sets as supplied with the appliance are to be used Old or other manufacturer s hose sets should not be re used f the appliance is located where the ambient air temperature could fall below 4 C when the heater is not in use do not turn off the power supply to the appliance This safeguard does not offer the same protection to the connecting pipework and fittings The ambient temperatures this unit should operate within are 4 C to 45 C Turn off power to unit by unplugging the power cord from the power point if water supply is turned off Caution and safety Boiling water is dangerous and can cause severe burns particularly with young children Boiling water must always be h
10. ck icon on top of the touch lens you will be able to dispense boiling water for 8 seconds After 8 seconds the safety switch will automatically reactivate and the red padlock icon will appear again Power save mode settings Ecolntelligence standby or on 24 7 The Green icons on the tap indicates the power save level that is selected To change or activate a setting once in options mode press and release the blue right button to scroll through the following options Green leaf icon on indicates Eco Intelligence self learning timer is enabled Moon amp star icon on indicates Standby Mode is enabled Blue Icon On no green icons indicates system is in 24 hour continuous mode To save new setting and exit Options Mode press the safety switch and release Wait 10 seconds for unit to return to normal operation with the desired settings Holiday mode To set press the pressure relief valve located under the unit cover beside the filter housing User guide Billi B 4000 XL Dispenser Icon codes Dispenser Icon Orange dot Flashes when filter change due On constant when overdue Red lock illuminated Safety button activated To use press the indent on the back of the tap momentarily amp lift or press the boiling lever Green leaf illuminated Eco intelligence Green moon amp stars illuminated In holiday mode or off Green moon amp stars flashing I
11. duces amp Removal Filter Change Due Monitor The B 4000 filter change due monitor operates by counting the number of cups dispensed and the number of days elapsed until a pre set level is reached Once reached the dispenser icons will briefly change to orange once every five seconds The B 4000 will continue to operate while the filter indicator is flashing Water filters installed in areas with higher levels of sediment will experience a reduced service life It may be necessary to change filters before the change filter indicator flashes If particularly dirty water is noticed coming through the water supply e g from other tap ware immediately place your Billi B 4000 into Holiday Mode by pressing the Pressure Relief button This will help prevent premature blocking of the filter cartridges Filter Order Taste Fluoride Expected Type PartNo Suits Micr Filters Sediment Chlorine VOCs Chemicals Odour Minerals Life Billi 6 12 Sub 994001 p 5gg 90 Single v v v v Y Slight hs Billi 6 12 Prem 994002 B 4000 0 2 Single v 4 v v Y Ananth 10 User guide Billi B 4000 XL XT XR Filter removal and replacement instructions Important note Please ensure you remove the foam packing under the filter before installing 1 Remove the front panel 2 Place the unit in Holiday Mode by pressing the Pressure Relief button once The lights on the dispenser will alternate and then go off 3 Hold filter and
12. illi may provide a replacement product free of charge If Billi elects to do this Billi will also pay the necessary freight charges and the customer will pay for the removal of the product and the costs of reinstalling the replacement product Any product replaced or repaired under this Product Warranty will be covered by the product s remaining warranty period or three months whichever is greater If the product or any part thereof is replaced by Billi under this Product Warranty all of the right title and interest in and to the replaced product or part shall vest in Billi upon it being replaced Warranty exclusions 1 Billi shall not be liable under this Product Warranty a unless the product was installed correctly and as per the installation instructions supplied with the product if the defect is contributed to or caused by any improper usage of the product or usage of the product for purposes other than that for which the product was designed or intended if the defect occurs wholly or partially as a result of any act or omission by the customer or any person other than Billi if the product is subject to misuse neglect accident or abuse or the customer continues to use the product after the defect becomes apparent e if the product is damaged as a result of poor water quality f if the product is repaired or any attempt to repair the product is made by anyone other than an authorised repairer of
13. n standby mode Red dot Flashes when heating up to temperature On constant when boiling water ready Off when in holiday standby or boilng water disabled Blue dot On constantly to indicate filtered water Red amp Blue dots will flash yellow if the unit goes into fault O Red Normal operation _ _ Normal operation Red e SO erating temperatures of hot and cold water not Blue mo OU yet reached Red Boiling water disabled Red Blue System in holiday or standby mode or off Orange mom OOOO Orange mmm i XX e O Blue O o Unit in fault mode User guide Billi B 4000 XT Dispenser Icon codes Dispenser Icon Orange dot Flashes when filter change due On constant when overdue Red lock illuminated Safety button activated To use press the indent on the top of the tap momentarily amp lift or press the red button Green leaf illuminated Eco intelligence Green moon amp stars illuminated In holiday mode or off Green moon amp stars flashing In standby mode Red ring Flashes when heating up to temperature On constant when boiling water ready Off when in holiday standby or boiling water disabled Blue ring On constantly to indicate filtered water Red amp blue rings will flash yellow if the unit goes into fault
14. ng option mode Within the options mode you can set the safety switch thorough the hot red button left and power save mode through the blue button right To enter the options mode 1 Turn on the unit and wait for normal operation red and blue buttons are both illuminated constantly 2 Press both the red and blue buttons amp then while pressing the two buttons touch the red lock icon located in the middle and owards the end of the lens Press and hold both buttons and safety switch for three seconds 3 Icons will flash yellow 4 Release the safety switch and red and blue buttons 5 Unit is now in options mode 6 If you wish to change or activate the power saving mode follow the power save mode settings procedure below Safety Switch settings The Red padlock indicates the different safety settings enabled To change or activate a setting once in options mode as above press and release the red left button to scroll through the following options Red Icon Off indicates the hot tap is disabled Padlock icon on Red icon on indicates hot tap safety switch is enabled Red Icon On indicates normal operation with safety switch not enabled To save new setting and exit Options Mode touch the safety switch and release Wait 10 seconds for unit to return to normal operation with the desired settings To dispense boiling water once the safety switch is activated simply touch the red lo
15. on smearing cleaner such as Windex is recommended Do not pour water over dispenser Cupboard ventilation requirements Your Billi B 4000 underbench module requires no cupboard ventilation but requires air space around the unit of 25mm Care should be taken when using the cupboard space to avoid stretching or damaging plastic pipe work Check fittings and tubing at each filter change for signs of damage or leakage Always ensure access to power switch and water supply tap is not restricted User guide Billi B 4000 XL XT XR Features and Modes Dispenser Swivel The B 4000 dispenser incorporates a swivel function allowing the dispenser to be swung out of the way if more sink space is required A central position stop provides positive location during normal usage Safety timeout The Billi B 4000 incorporates a water delivery Safety Timeout to prevent an uncontrolled flow of water Water flow stops automatically after a set time interval Flow can be started again by releasing and pressing the dispenser lever or for the XT or XR option simply press either the red or blue button Boiling water timeout 10 secs Childproof safety switch The Billi B 4000 is fitted with a childproof safety lock out feature to protect against accidental dispensing of boiling water and the risk of burns Please refer to page 5 Standby mode Standby operation may be optionally enabled to reduce power consumption
16. ralia As Billi Pty Ltd has a policy of continual improvement all details are subject o change without notice All goods are sold subject to our published terms and conditions Billi is a registered rademark 0514
17. swing towards you slowly The top of the filter is in a hinged cradle assembly It should stop after approximately 30 degrees of travel 4 The filter can now be released from the holding cradle by pulling down on the filter 5 Take care not to spill water in the base of the ray If so wipe gently with absorbent paper 6 Install new filter into the same location by pushing all the way up into the cradle 7 Push filter back into the unit until it locks into place Power light should come back on 8 Flush ambient water for 1 minute Wait for 10 minutes Flush ambient for an additional 1 minute 9 Check for any leaks from around the filter hosing or pipeworks 10 Replace the front cover Front 4 pannel Pressure relief button Filter 11 User guide Billi B 4000 XL XT XR Thank you for choosing to install a Billi B 4000 Drinking Water Appliance Your B 4000 is manufactured to exacting standards using high quality materials and with proper maintenance and care should function for many years For information on our filtration and service contract please contact Billi Head Office on 1800 812 321 or email us at service billi com au For technical support please call 1800 812 321 and speak to one of Billi s experienced technician s To book a service call out request a filter change or please contact the Billi Service
18. tes hot tap safety switch is enabled Red Icon On indicates normal operation with safety switch not enabled To save new setting and exit Options Mode touch the safety switch and release Wait 10 seconds for unit to return to normal operation with modified settings Power save mode settings Ecolntelligence standby or on 24 7 The Green icons on the tap indicates the power save level that is selected To change or activate a setting once in options mode press and release the ambient right lever to scroll through the following options Green leaf on indicates Eco Intelligence self learning timer is enabled Green moon amp stars icon flashing indicates Standby Mode is enabled White Icon On indicates system is in 24 hour continuous mode To save new setting and exit Options Mode press the safety switch and release Wait 10 seconds for unit to return to normal operation with now settings Holiday mode To set press the pressure relief valve located under the unit cover beside the filter housing User guide Billi B A000 XT XR Options amp Operation To operate simple press the red left button to dispense boiling water and blue right button ring to dispense ambient filtered water When the red or blue buttons are double tapped the water will dispense continually until interrupted by another light press of either button Operating modes can be selected by the user by enteri
Download Pdf Manuals
Related Search