GPL168001A Confirmation Sheet
Contents
1. GENERALPLUS devices It is the customer s responsibility to check all the information in the list No responsibility is assumed by GENERALPLUS or any non checked box even this confirmation sheet has been approved by GENERALPLUS Make sure the following conditions are met and verified All used SRAM must be initialized after power on Strongly recommended Make sure the used SRAM variables are not over stack reserved area Make sure the Interrupt section is located in the pageO or is declared as TEXT section 08000 0FBFF A Make sure no current leakage in I O or speaker amplifier during sleeping B Make sure all I Os are not floating during sleeping Check To avoid abnormal wake up in sleep mode users should disable the interrupt of all sources with 32768Hz clock Non used I O ports must be masked off for input process Example if IOA 0 7 are input R1 P_IOA_Data Read I O port A Data R1 amp OxOOFF Mask higher byte Check CMP R1 0x0011 Lower byte is available for compare operation Document Version To make sure the correct version of document is used please fill out the followings A GPL168001A Programming Guide Version B u nSP IDE User Manual Title and Version C Other documents if any Specific Mailbox gocode generalplus com TEL 886 3 6662118 FAX 886 3 66621 17 GE GPL168001A Confirmation Sheet easel V1 4 07 18 2012 De2. register Value written to 0x7021 CS1 timing control register Value written to 0x7024 A D Interface Disable Enable If Enable please check following Module Used Microphone if used Auto Gain Control _ Enable Disable Analog Input s If used A D Line_In inputs CHC CHD shared with IOB 1 0 voltage range V V Specific Mailbox gocode generalplus com TEL 886 3 6662118 FAX 886 3 6662117 G GPL168001A Confirmation Sheet Panola V1 4 07 18 2012 Disable Enable If Enable Maximum Baud Rate Disable Enable If Enable Maximum Baud Rate SEG 0 7 Used as key scan output No If yes please check LCD brightness on Emu Board ISEG 8 15 Used as key scan output Watchdog enable Software Write once Option If watchdog is enabled please check the following Watchdog port 700BH must be cleared by writing OxAxx5 within some designated duration All functions must be verified on the EMU board or EMU chip system Mask Code Option EMUSELO code option as EMUSEL1 code option as IROMEN code option as ADBUSEN code option as Protect code option as General Programming Checklist The general programming checklist intends to provide some general characteristics about
3. 0 0x0F BFF Check Non Page0 ROM size 480K words 0x10000 0x87FFF Check IGENERALPLUS test program 1K words 0xFC00 0xF FEF Check Reserved Area Input Output IOA Port JOA Port o o OS bs bia brs b12 b11 bio vo os bz ve bs ba os be bt bo COMMON 63 61 Specific Mailbox gocode generalplus com TEL 886 3 6662118 FAX 886 3 66621 17 GPL168001A Confirmation Sheet Generalplus V1 4 07 18 2012 bis b14 b13 p12 b11 b10 b9 ba oz bo bs ba bs b2 bt bo D IOB Port Input Output Wakeup Special T Cc Q g 0 Input Output akeup Special Dedicated I O lt ys Function Used Hardware Software Enable 2 0V Enable 2 2V In emulation mode setup Value written to 0x704C Released mask code setup Value written to 0x704C This value must be greater than 0x0001 and must be verified on EMU system Disable Enable Start Address End Address Type LJSRAM ROM FLASH Others Size Access Time CS0 control register Value written to 0x7020 Disable Enable Start Address End Address Type _JSRAM ROM FLASH Others Size Access Time CS1 control
4. FAX 886 3 66621 17
5. G GPL168001A Confirmation Sheet kaaa V1 4 07 18 2012 a Project Description CPU Working Voltage VDD _12 7V 3 6V I O Voltage 2 7V 3 6V Clock control register Value written to 0x7007 Crystal CPU Operation Frequency i Check CPU operation MHz 32768Hz LCD Configuration COM SEG ss Bias Duty V Mode _ Gray Level Mono Black amp White Bit per pixel 1 4 LCD Buffer can only locate in DPRAM 0x4000 0x477F C Check LCD Setup register Value written to 0x7180 LCD Driver Interface Frame Rate Hz List SEG Control Register 0x7031_ s Ox7032_ Ox7033_ s lt Ox7034_ LCD Common Can only use GPL168001A built in COM Driver up to 64 COM Check LCD Segment Single Chip Solution GPL168001A Multi Chip Solution If Multi Chip Solution a Make sure to turn off GPL168001A built in VLCD charge pump b Can not use GPL168001A built in SEG69 SEG73 Project Title LCD Driver Components GPLD Series Body no SPLC Series Body no Others Body no Release Code File fill OxFFFF for unused area Binary filename tsk Binary file check sum Binary file size is 1088 Kbytes run sunb exe result User ROM check sum Reported by G IDE tool SRAM size 4K words 0x00000 0x0FFF Check DPRAM size 1920 Words 0x4000 0x477F Check Page0 ROM size 31K words 0x0800
6. velopment Tool Board Version To make sure the correct version of hardware is used please fill out the followings A Emulation Board Version B Emulation Chip Version C Piggyback Version if used D Others if any To make sure the correct version of software is used please fill out the following A u nSP IDE Version B SACM Library Version if used C Others if any Speech Library Usage Generalplus speech libraries is applied in this code If yes which kind speech have used A1600 A2000 A3200 A3200 2 channel A2000 Encode 200 240 480 720 530 S600 Does speech algorithm allocate in page 0 For Third Party Application Cyberon voice recognition solution is applied in this code If yes please fill out the followings A Types of solutions _ SI only SD only SID both SI amp SD B VStar Modeling Toolkit IDE Version C VStar Library Version BSRV lib D VStar SDK Programming Guide Version E Others if any Customer Note GENERALPLUS Note Name print Tel Name print Tel i ee l Note Please send fax this form to GENERALPLUS GENERALPLUS will return it back with signature Specific Mailbox gocode generalplus com TEL 886 3 6662118
Download Pdf Manuals
Related Search