ULT800 - Fluke
Contents
1. Figure 2 HP Agilent Disinfection Basin Test Setup Using the ULT800 600 210 HP Agilent Transducer Adapter 600 212 Dual Conductivity Electrode with 600 213 ATL Extenders Disinfection and Storage Tube ecy03f eps Figure 3 ATL Disinfection Storage Tube Setup ULT800 Users Guide Checking the Battery Note The LOW BAT light flashes red to indicate that the battery needs replacement 1 Use the LEAKAGE CONDUCTIVITY switch to select CONDUCTIVITY 2 Press the ON TEST button to turn on the ULT800 The self check routine starts calibrating the unit All four LED indicators flash in sequence continuing for five cycles The READY light glows amber when the self test routine completes with a successful battery test Checking Solution Conductivity Note The LED indicating a test result remains on for 12 seconds The ULT800 then powers off to conserve the battery To resume testing power on the ULT800 allow the self check battery test to complete and then reinitiate the test 1 Select CONDUCTIVITY 2 Press the ON TEST button to perform a measurement cycle 3 At the end of the measurement cycle two seconds the LED indicates the results of the test The green PASS light illuminates if the solution passed the Conductivity Test The red FAIL light illuminates if the solution failed the Conductivity Test Check that you have immersed the electrodes to2. anywhere in the world at 1 425 446 5500 or call for service in the USA at 1 888 99 FLUKE 1 888 993 5853 Accessories Accessories Refer to Table 2 for a list of transducer adapters and other accessories for the ULT800 Table 2 Accessories Part Model Number Number Description 2392430 600 156FG Ultrasound Transducer Adapter Siemens Acuson 156 series probes 2392453 600 202FG Ultrasound Transducer Adapter GE YMS RT 2392466 600 203FG Ultrasound Transducer Adapter GE CGR 2392475 600 204FG Ultrasound Transducer Adapter GE LogiQ 2231602 600 205 Ultrasound Transducer Adapter GE LogiQ 2392482 600 210FG Ultrasound Transducer Adapter HP Agilent 2392494 600 211FG Ultrasound Transducer Adapter HP Agilent 2392516 600 213FG Ultrasound Transducer Adapter Acuson Toshiba 13 ULT800 Users Guide Table 2 Accessories cont Part Model Number Number Description 2392540 600 216FG Ultrasound Transducer Adapter Hitachi 2392557 600 218FG Ultrasound Transducer Adapter Philips ATL 2392578 600 260FG Ultrasound Transducer Adapter Siemens Acuson 260 series probes 2231811 600 360 Ultrasound Transducer Adapter Siemens Acuson 360 series probes 2392591 600 MPFG Ultrasound Transducer Adapter Siemens Acuson MP series probes 2392427 600 102FG Chassis ground probe 8 foot coiled cord 2231616 600 206 Universal ultrasound probe
3. s specifications Warranty Disclaimer Should you elect to have your instrument serviced and or calibrated by some one other than Fluke Biomedical please be advised that the original warranty covering your product becomes void when the tamper resistant Quality Seal is removed or broken without proper factory authorization We strongly rec ommend therefore that you send your instrument to Fluke Biomedical for factory service and calibration especially during the original warranty period In all cases breaking the tamper resistant Quality Seal should be avoided at all cost as this seal is the key to your original instrument warranty In the event that the seal must be broken to gain internal access to the instrument you must first contact Fluke Biomedical s Technical Assistance Department at 775 883 3400 You will be required to provide the serial number for your in strument as well as a valid reason for breaking the Quality Seal You should break this seal only after you have received factory authorization Do not break the Quality Seal before you have contacted us Following these steps will help ensure that you will retain the original warranty on your instrument without interruption Fluke Biomedical 6920 Seaway Blvd Everett WA 98203 USA Introduction The ULT800 TEE Transducer Leakage Current Tester measures the leakage current of ultrasound transducers independent of their ultrasound systems Use the hand held battery opera
4. 2392502 600 212FG Dual conductivity electrode 2392525 600 214FG Hard sided carrying case 2392533 600 215FG Conductivity cable 2392569 600 220FG Dual conductivity probe 14 Symbols Symbols Symbol Description A See Users Guide A Caution risk of electric shock Standby On A A 0 Manufacturer s declaration of product compliance KE with applicable EU directives x E233218 Do not mix with solid waste stream Dispose using a qualified recycler or hazardous material handler Satna 15 ULT800 Users Guide
5. FLUKE Biomedical ULT800 TEE Transducer Leakage Current Tester Users Guide PN 2461434 August 2005 2005 Fluke Corporation All rights reserved Printed in USA All product names are trademarks of their respective companies Warranty and Product Support Fluke Biomedical warrants this instrument against defects in materials and workmanship for one full year from the date of original purchase During the warranty period we will repair or at our option replace at no charge a prod uct that proves to be defective provided you return the product shipping prepaid to Fluke Biomedical This warranty does not apply if the product has been damaged by accident or misuse or as the result of service or modification by other than Fluke Biomedical INNO EVENT SHALL FLUKE BIO MEDICAL BE LIABLE FOR CONSEQUENTIAL DAMAGES Only serialized products and their accessory items those products and items bearing a distinct serial number tag are covered under this one year warranty PHYSICAL DAMAGE CAUSED BY MISUSE OR PHYSICAL ABUSE IS NOT COVERED UNDER THE WARRANTY Items such as cables and nonserialized modules are not covered under this warranty Recalibration of instruments is not covered under the warranty This warranty gives you specific legal rights and you may also have other rights which vary from state to state province to province or country to country This warranty is limited to repairing the instrument to Fluke Bio medical
6. a depth of at least 25 mm 1 inch and that they are firmly connected to the ULT800 then retest If the failure repeats replace the solution and then retest Testing for Transducer Leakage Current Testing for Transducer Leakage Current Note Perform the Leakage Test only if the Conductivity Test passes 1 Select LEAKAGE 2 Press the ON TEST button to perform a leakage measurement The green PASS light illuminates if the transducer passed the leakage current test The red FAIL light illuminates if the transducer failed the leakage current test If there is less than 20 WA of leakage current the red light pulses indicating a possible open circuit condition with invalid test results Maintenance Your ULT800 needs little maintenance or special care However treat it as a calibrated measuring instrument Avoid dropping or other mechanical abuse that could cause a shift in the calibrated settings Cleaning A Caution Do not pour fluid onto the ULT800 surface fluid seepage into the electrical circuitry may cause ULT800 failure A Caution Do not use spray cleaners on the ULT800 such action may force cleaning fluid into the ULT800 and damage electronic components Clean the ULT800 occasionally utilizing a damp cloth and mild detergent Take care to prevent the entrance of liquids Wipe down the adapter cables with the same care Inspect them for damage to and deterioration of the insulation Check the connections for integr
7. battery operated device It measures the leakage current of the devices attached to its connectors The ULT800 applies 120 VAC 60 Hz to devices placed in a conductive bath basin or storage tube The ULT800 measures the current and compares the results to an internal threshold The instrument displays the results as a PASS or FAIL indication It also performs an internal self calibration on each measurement cycle The ULT800 makes two types of measurements The Leakage Test measures the current between the probe and the electrode The Conductivity Test measures the conductivity of the bath solution between the two electrodes Figures 2 and 3 show some typical test setups Figure 2 shows the HP Agilent Disinfection Basin HP Part No 21110A Figure 3 shows the ATL Disinfection and Storage Tube You can use other setups as long as you observe the following rules 1 Connect the ultrasound probe you are testing to the probe adapter See the list of available adapters under Accessories 2 Place the probe you are testing in a saline bath with the entire critical area of the probe fully immersed 3 Place the dual electrode Part No 2392502 or 2392569 in the saline bath to a depth of at least one inch ULT800 Users Guide 4 Plug the probe adapter and the electrode wire connectors into the ULT800 The connections are fully interchangeable 600 212 HP Agilent _ 600 210 ecy02f eps
8. ibutor or Fluke Electronics office Claims Our routine method of shipment is via common carrier FOB origin Upon delivery if physical damage is found retain all packing materials in their original condition and contact the carrier immediately to file a claim If the instrument is delivered in good physical condition but does not operate within specifications or if there are any other problems not caused by shipping damage please contact Fluke Biomedical or your local sales representative Certification This instrument was thoroughly tested and inspected It was found to meet Fluke Biomedical s manufacturing specifications when it was shipped from the factory Calibration measurements are traceable to the National Institute of Standards and Technology NIST Devices for which there are no NIST calibration standards are measured against in house performance standards using accepted test procedures Support Obtaining Assistance If you have trouble operating the equipment or just need some clarification on its operation contact Fluke Biomedical s Technical Assistance Center at 800 648 7952 Returning the Instrument to Fluke If it becomes necessary to return your instrument to Fluke proceed as follows 1 Every product returned to Fluke must have a Return Material Authorization RMA number To obtain an RMA contact Fluke through one of the following methods Phone 888 99FLUKE 888 993 5853 or 425 446 5560 Email ser
9. ity 11 ULT800 Users Guide Battery A Warning The 9 volt alkaline battery provided with the ULT800 may explode or leak if recharged inserted improperly disposed of in a fire or mixed with different battery types Dispose of the battery in accordance with any applicable state or local regulations The ULT800 uses a standard 9 volt alkaline battery The battery has a life expectancy of approximately 1000 measurements Replace the battery yearly regardless of its condition Calibration A Warning Examine the calibration label on the back of the ULT800 prior to each use Do not use a ULT800 with an expired calibration label A ULT800 without a calibration label or with the anti tamper case label broken is out of calibration A ULT800 that is out of calibration can cause excessive leakage current exposure to the patient risk of injury to the patient could result A Caution Avoid dropping the ULT800 or allowing other mechanical abuse that could cause a shift in the ULT800 s calibrated settings The ULT800 requires yearly Fluke factory calibration which uses appropriate tools and reference instruments that are traceable to the National Institute of Standards and Technology NIST Factory calibration provides a calibration sticker on the back of the ULT800 to verify that the calibration was performed To locate a service center visit the Fluke web site at www fluke com or contact Fluke at service fluke com Call from
10. t condition with invalid test results LOW BAT Flashes red to indicate that the battery requires replacement LEAKAGE CONDUCTIVITY Selects the test to perform SWITCH ON TEST BUTTON Turns the ULT800 on and initiates the selected test BATTERY COMPARTMENT not shown Holds a 9 volt alkaline battery The instrument automatically powers off if you do not perform a test within 12 seconds ULT800 Users Guide Specifications Power 9 V Alkaline Battery No of Measurements Approximately 1000 measurements on a single battery Conductivity Limit to pass greater than 250 LA 5 Leakage Limits to pass less than 100 UA 5 and greater than 20 uA 5 WA Dimensions 6 5 x 3 7 x 1 5 in 17 x 19 x 4 cm Weight 12 oz 340 g Environmental Operation Temperature 15 to 40 C Storage Temperature 15 to 65 C Relative Humidity 90 Max Using the ULT800 Using the ULT800 A A Warning To avoid personal injury do not touch the dual conductivity electrode rods Voltage is present on the rods during a test Inspect the conductivity probe for damaged insulation or exposed metal To avoid personal injury replace a damaged conductivity probe before using A Caution To avoid damage to the transducer observe the immersion levels Do not immerse or allow the cable or connector of a transducer to become wet The ULT800 TEE Transducer Leakage Current Tester is a portable self contained
11. ted instrument during the routine transducer cleaning procedure conducted between patients Connect the transducer to be tested to the ULT800 via a unique adapter The ULT800 performs the measurement with the transducer immersed in either the cleaning solution or saline To insure that the leakage current test is accurate first test the conductivity of the fluid A special dual element probe also connected to the ULT800 tests the conductivity of the fluid A green PASS light or a red FAIL light indicates the results of the conductivity and leakage current tests In addition to verifying that the ultrasound transducers are safe for patient use the ULT800 makes it possible to reduce expensive repairs Identifying transducers that exceed safe leakage currents early may allow for repairs to be made before a transducer becomes non repairable Key Features e Hand held instrument e Stand alone operation e Direct measurement of leakage current e Battery operation for safety e Independent of 120 or 240V ac systems e Built in self test circuit e Auto shut off to conserve battery ULT800 Users Guide Support Customer Support and Sales USA and Canada 800 648 7952 Outside the USA 775 883 3400 E Mail sales flukebiomedical com Internet www flukebiomedical com Service Service 888 993 5853 Outside the USA 425 446 5560 E Mail service fluke com For additional sales or service information contact your local Fluke Biomedical Distr
12. vice fluke com 2 Pack the instrument carefully using the original packing materials if available Failure to pack the instrument properly could void your warranty and result in you paying for the instrument s repair Insure the unit for full retail value and ship to the address specified by Fluke ULT800 Users Guide Controls and Indicators Input connectors are interchangeable and provide for inputting an ultrasound transducer adapter and the dual conductivity electrode Refer to Figure 1 and Table 1 for complete control and indicator descriptions LEAKAGE CONDUCTIViry INSTRUC TIONS 1 Conne ct the tra 2 Press wy nSducer and the a e ON TEST button PLETS to the yyy S and a 3 Select COND it for the A Wait for th Wai UCTIVITy e READY Jie PASS hgn oie Ind Press the ONTEST p tte utton and PASS or pay P SSS the o TRANSDUCER AIL light Pisin TEST p Refer to the usera fils DO No nual ecy10f eps Figure 1 Controls and Indicators Controls and Indicators Table 1 Controls and Indicators Item Description READY Glows amber when the self test procedure completes approx 8 sec The ULT800 is then ready for testing PASS Glows green when either the Conductivity Test or Leakage Test passes FAIL Glows red when either the Conductivity Test or the Leakage Test fails Pulses red when the Leakage Test results in less than 20 LA indicating a possible open circui
Download Pdf Manuals
Related Search