USER MANUAL
Contents
1. light beam shine on skin do not look at the light source directly Prevent short circuit happening to temperature control switch and safety box When replace defective fuse choose approved new fuse of the same type Keep the distance more than 1 M from equipment to flammable material such as cloth wood paper Keep the distance 0 1 M from fan to vent When housing of equipment feels very hot cool it for 15 minutes before operation Advise you to choose accessories produced by us when install and replace Whenever install or move equipment set an alarm to prevent others entering job site Do not put your hand between side arm and light structure when light working shown in picture 1 by arrow Keep the optical system clean Make the maintenance according to this manual when use in messy and dusty environment Luminous flux will decrease once the mirror gets covered by fatness or dust Solutions to problems Phenomenon of power supply o o Lamp does not light motor does not work itself When reset indicator light of On Off does not light Lamp lights reset but one of the protocols out of control Lamp not in stable control for lighting Light spot not bright enough Lamp lights then black out and lights again in a while Causes 0 Power supply not in normal state not well connected the fuse breaks up Control line not connected or connected not to the right address code please check the address co2. 255 FUNCTION 0 199 Big to Small 200 255 Automatism slow fast CHANNEL 9 FIXED GOBO WHEEL DMX 512 VALUE 0 255 FUNCTION 0 White 01 16 GOBO 1 No rotating 17 33 GOBO 2 No rotating 34 50 GOBO 3 No rotating 51 67 GOBO 4 No rotating 68 84 GOBO 5 No rotating 85 101 GOBO 6 No rotating 102 118 GOBO 7 No rotating 119 135 GOBO 8 No rotating 136 153 White 154 158 GOBO 8 No rotating 159 163 GOBO 7 No rotating 164 168 GOBO 6 No rotating 169 173 GOBO 5 No rotating 174 178 GOBO 4 No rotating 10 179 183 GOBO 3 No rotating 184 188 GOBO 2 No rotating 189 193 GOBO 1 No rotating 194 198 White 199 219 GOBO Animation Fast to Slow 220 240 GOBO Animation Slow to Fast 241 255 Random Gobo CHANNEL 10 ROTATING GOBO WHEEL DMX 512 VALUE 0 255 FUNCTION 0 127 Clockwise Revolve Slow Fast 128 252 Anticlockwise Revolve Fast Slow 253 255 Not Rotation CHANNEL 11 GOBO ROTATION DMX 512 VALUE 0 255 FUNCTION 0 127 Clockwise Revolve Slow Fast 128 252 Anticlockwise Revolve Fast Slow 253 255 Not Rotation CHANNEL 12 FOCUS DMX 512 VALUE 0 255 FUNCTION 0 255 Linear focusing CHANNEL 13 ZOOM DMX 512 VALUE 0 255 FUNCTION 0 255 Linear Amplify CHANNEL 14 PRISM DMX 512 VALUE 0 255 FUNCTION 0 31 White 32 255 P
3. CH 19 Gobo Marcos 0 255 CH 20 Vector mode Back Test operation Sound program run Auto program run Back Resume default Enter Fixture reset pe Enter Indicate info Link error System reset zd INSTALL THE FIXTURE 1 Make sure that the point of fixing is stable before positioning the light It must bear more than 10 multiple of the light weight 2 Use two special M10 bolts to fix the fixed screw which is in the projector s soleplate ensure projector can t fall And must use rope to tie the projector s handle and other fixing points when you fix them 3 when positioning the projector the distance between the objects that beam hi and the lens of projector should keep more than Imeter and the minimum distance from the surface of projector to any flammable material should be at least 0 5meters In order to ensure the light working normally and stably the ambient temperature must not exceed 35 II 14 Install and Replace the lamp 1 Unscrew the 2 screws at the back of the fixture and then pull the lamp socket 2 If changing the lamp please just remove the old one from the socket 3 Holding the new lamp align the small pin on the lamp with the small hole in the socket and insert the lamp squarely 4 Align the screw holes and fasten the lamp access plate with 2 screws 5 Please check whether the lamp was fixed tightly Otherwise poor connection may lead to short circuit discha
4. MX Tere GND Connecting DMX512 digital signal Please using high quality screen line to connect it for fear interfering GND TED oa DIGITAL SIGNAL AUR HH 16 Rigging Optional This equipment can be positioned and fixed by clamp in every direction of the stage Locking system makes it easy to fasten to the bracket Attention Two clamps is needed to fix the equipment Every clamp is locked by fastener of 1 4 kind Fastener can only be locked clockwise Attention Fasten a safety string to the additional hole of side aluminum piece The secondary accessory can not hang on the delivery handle Nip the equipment on bracket 1 Check if rigging clamp not including the one inside damaged or not If stand ten times weight as the equipment Make sure the architecture can stand ten times weight as all the equipments clamps wirings and other additional fixtures 2 Screws for clamping must be fixed firmly Take one M12 screw Grade 8 8 or higher to clamp bracket and then screw the nuts 3 Level the two hanging points at the bottom of clamp Insert fastener to the bottom lock the two levers by 1 4 rotating clockwise then install another clamp 4 Install on safety string which stands at least ten times weight as equipment Terminal of the accessory is designed for clamps 5 Make sure pan tilt lock unlocked or not Keep the distance more than 1M from equipment to flammable material or lighting source Maintenance Inst
5. OTOCOL Basic model 16bt CHANNEL 1 STROBE RESET SHUTTER DMX 512 VALUE 0 255 FUNCTION 0 19 Shutter Close 20 49 White 50 100 Strobe fast slow 101 107 White 108 127 Shutter Close 128 147 Shutter Open 148 155 White 156 235 Strobe Random 236 245 Reset 246 250 Shutter Open 251 255 Shutter Close CHANNEL 2 DIMMER DMX 512 VALUE 0 255 FUNCTION 0 255 Dark Light CHANNEL 3 COLOR WHEEL 1 DMX 512 VALUE 0 255 FUNCTION 0 153 Angle 154 163 Rose red 164 168 Purple 169 173 Orange 174 178 Green 179 183 Yellow 184 188 Blue 189 193 Red 194 198 White 199 219 Rainbow Clockwise Revolve fast to slow 220 240 Rainbow Anticlockwise Revolve slow to fast 241 255 Random change color CHANNEL 4 COLOR WHEEL 2 DMX 512 VALUE 0 255 FUNCTION 0 153 Angle 154 163 Effect Color 164 168 Light rose red 169 173 Light Blue 174 178 Yellow and Green 179 183 Pink 184 188 Temperature decreasing 189 193 Temperature increasing 194 198 White 199 219 Rainbow Clockwise Revolve fast to slow 220 240 Rainbow Anticlockwise Revolve slow to fast 241 255 Random change color CHANNEL 5 PAN DMX 512 VALUE 0 255 FUNCTION 0 255 Pan Max 450 CHANNEL 6 TILT DMX 512 VALUE 0 255 FUNCTION 0 255 Tilt Max 270 CHANNEL 7 X amp Y Speed Vector Mode DMX 512 VALUE 0 255 FUNCTION 0 251 Scan speed adjustment fast to slow 252 255 Vector CHANNEL 8 IRIS DMX 512 VALUE 0
6. RISM CHANNEL 15 PRISM ROTATION DMX 512 VALUE 0 255 FUNCTION 0 127 Angle adjustment 128 191 clockwise Revolve Fast Slow 192 255 Anticlockwise Revolve Slow Fast CHANNEL 16 VECTOR MODE DMX 512 VALUE 0 255 FUNCTION 0 251 Not vector 252 255 Color Rotating gobo Prism Vector ll LCD DISPLAY BOARD AND ADDRESS SET INSTRUCTION MENU FUNCTION OPTION Original status DMX address 001 Exit return to original status DMX address DMX address back 5 i Gonit Standard arameter ontro Extended Model EAGLE 1008 No X Reverse Yes No Y Reverse Yes No XY Exchange Yes No Option Dimmer Reverse Yes No Ins Reverse Yes No Turn shortest Yes No DMX reset Yes Back Display Simplified Chinese Language English zd MENU FUNCTION OPTION back CH 1 Strobe Reset Shutter 0 255 CH 2 Dimmer 0 255 CH 3 Color Wheel 1 0 255 CH 4 Color Wheel 2 0 255 CH 5 Pan 0 255 CH6 Tilt 0 255 CH 7 Pan Fine 0 255 CH 8 Tilt Fine 0 255 CH 9 Pan amp Tilt Speed Vector Mode 0 255 Man Control CH 10 Iris 0 255 CH 11 Fixed Gobo Wheel 0 255 CH 12 Rotating Gobo Wheel 0 255 CH 13 Gobo Rotation 0 255 CH 14 Focus 0 255 CH 15 Zoom 0 255 CH 16 Prism 0 255 CH 17 Prism Rotation 0 255 CH 18 Color Marcos 0 255
7. USER MANUAL CE EAGLE 1008 MOVING HEAD SPOT 20 CHANNELS Please read over this manual before operating the light Professional Stage Lighting CONTENT OI st asa NORI PNR IRI PT MEM ee ATTENTION atata Bl eden ee ia aaa aa ERE TE DIRE Eos ac ca nec ae aia aa Edi ba ai PR AURUL S oo i ei a dania daca taiata SPECIFICATIONS oos OC IO RR RP RER RR PR CR TECHNICAL PARAMETER esec ei dd ege rr eek Tet DMX CHANNELS EXPENDING PATTERN DMX PARAMETER OEI asc o a al i al DMX PARAMETER IGB j econtra n Nu UEBER Ea LCDISPLAY FUNCTION acacia cada ei ie a INSTALL OR REPLACE A LAMP eee POWER SUPPLY MAINS eee cana POWER CONNECTION eee DMX 512 SIGNAL CONNECTION eee ea RIGGING OPTIONAL aaa MAINTENANCE er aia CRUS ii ac ala ee ATTENTION Thank you so much to choose our light EAGLE 1008 is powerful in functions with CE Standard It has been tested through frequent practice in deferent cases and well recognized by professional designers in the filed of stage light It fully shows the modern times light characteristic with good performance it can be used in all kinds of scenes with need high quality lighting Please read this manual carefully before powering or installing the fixture follow the safety precautions listed below and observe all warnings in this manual Warning Always disconnect from mains supply before replacing the lamp or not it will burn the light 1 Disconnect the fixture fro
8. all and replace lamp the attentions are as follows MSR lamp s average life is 750 hours please check if it works out before replace it Draw out the line of power supply Coolthe lamp for 10 15 minutes after it blacks out and then tweak the four screws Open the cover get the old lamp out and insert the new one Cleaning of lens system Wash exterior and interior optical mirrors to enhance the brightness in regular time especially when equipment used in messy surroundings Use mirror cleanser or alcohol to wash exterior mirrors in every 15 20 days 40 60 days for interior focusing prism reflector Safety information Donotseparate the light personally Prevent liquid water and metal into the equipment The equipment not fit for cases below Relative humidity is too high Shake and hit Room temperature is above 40 degree or below 0 degree o o Relative temperature is below 30 degree or above 80 degree 17 0 99 Replace the housing lens and ultraviolet radiation when visible damage takes place such as cracks Replace the lamp when damage happens to it or its maximum life is used up Shut off the power supply when replace lamp safety box and any other accessories and when it does not work Keep the ground switch connected to ground Power supply must meet the local standard on architecture and electric signal with overload protection and connect to earth Do not make
9. asing 194 198 White 199 219 Rainbow Clockwise Revolve fast to slow 220 240 Rainbow Anticlockwise Revolve slow to fast 241 255 Random change color CHANNEL 5 PAN DMX 512 VALUE 0 255 FUNCTION 0 255 Pan Max 450 CHANNEL 6 TILT DMX 512 VALUE 0 255 FUNCTION 0 255 Tilt Max 270 CHANNEL 7 PAN FINE DMX 512 VALUE 0 255 FUNCTION 0 255 Pan fine adjustment 3 6 CHANNEL 8 TILT FINE DMX 512 VALUE 0 255 FUNCTION 0 255 Tilt fine adjustment 3 6 CHANNEL 9 X amp Y Speed Vector Mode DMX 512 VALUE 0 255 FUNCTION 0 251 Scan speed adjustment fast to slow 252 255 Vector CHANNEL 10 IRIS DMX 512 VALUE 0 255 FUNCTION 0 199 Big to Small 200 255 Automatism slow fast CHANNEL 11 FIXED GOBO WHEEL DMX 512 VALUE 0 255 FUNCTION 0 White 01 16 GOBO 1 No rotating 17 33 GOBO 2 No rotating 34 50 GOBO 3 No rotating 51 67 GOBO 4 No rotating 68 84 GOBO 5 No rotating 85 101 GOBO 6 No rotating 102 118 GOBO 7 No rotating 119 135 GOBO 8 No rotating 136 153 White 154 158 GOBO 8 No rotating 159 163 GOBO 7 No rotating 164 168 GOBO 6 No rotating 169 173 GOBO 5 No rotating 174 178 GOBO 4 No rotating 179 183 GOBO 3 No rotati
10. ctor Mode DMX CHANNELS Basic model 16bb CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8 CH 9 CH 10 CH 11 CH 12 CH 13 CH 14 CH 15 CH 16 Strobe Reset Shutter Dimmer Color Wheel 1 Color Wheel 2 Pan Tilt Pan amp Tilt speed Vector mode Iris Fixed Gobo Wheel Rotating Gobo Wheel Gobo Rotation Focus Zoom Prism Prism Rotation Vector Mode DMX PROTOCOL 16EH CHANNEL 1 STROBE RESET SHUTTER DMX 512 VALUE 0 255 FUNCTION 0 19 Shutter Close 20 49 White 50 100 Strobe fast slow 101 107 White 108 127 Shutter Close 128 147 Shutter Open 148 155 White 156 235 Strobe Random 236 245 Reset 246 250 Shutter Open 251 255 Shutter Close CHANNEL 2 DIMMER DMX 512 VALUE 0 255 FUNCTION 0 255 Dark Light CHANNEL 3 COLOR WHEEL 1 DMX 512 VALUE 0 255 FUNCTION 0 153 Angle 154 163 Rose red 164 168 Purple 169 173 Orange 174 178 Green 179 183 Yellow 184 188 Blue 189 193 Red 194 198 White 199 219 Rainbow Clockwise Revolve fast to slow 220 240 Rainbow Anticlockwise Revolve slow to fast 241 255 Random change color CHANNEL 4 COLOR WHEEL 2 DMX 512 VALUE 0 255 FUNCTION 0 153 Angle 154 163 Effect Color 164 168 Light rose red 169 173 Light Blue 174 178 Yellow and Green 179 183 Pink 184 188 Temperature decreasing 189 193 Temperature incre
11. de Voltage is too low lamp close to using up Lamp close to using up optical mirror not clean Overheating protection please check if cooling system is blocked or not 18
12. l 6 interchangeable rotating gobos white bi directionally rotating at variable speed gobo shake function PRISM WHEEL 3 facet prism bi directionally rotating speed adjustable FOCUS Linearly adjustable ZOOM OPTICS Covering a range from 15 35 DIMMER 0 100 linearly adjustable STROBE SHUTTER Double strobe shutter blades 1 10 flash per second IRIS 5 100 linearly adjustable PAN ANDTILT Smooth automatic Pan Tilt position correction speed adjustable RANGE Pan 450 Tilt 270 16 bit VECTOR MODE Colour XY GOBO Prism vector COOLING Forced air cooling CONTROL DMX 512 3 pin interface CHANNELS Standard Mode 16 Extended Mode 20 DISPLAY LCD display brightness and contrast adjustable English Chinese language can set PROTECT GRADE IP20 overheating amp overvoltage protection NET WEIGHT Magnetic Ballast 39Kg GROSS WEIGHT Carton 44Kg Flight case 63Kg FIXTURE DIMENSION L440xW395xH690 mm PACKING DIMENSION Carton L515xW485xH758 mm Flight case L540xW435xH990 mm m DMX PROTOCOL DMX CHANNELS Expanding model 16EH CHI CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8 CH 9 CH 10 CH 11 CH 12 CH 13 CH 14 CH 15 CH 16 CH 17 CH 18 CH 19 CH 20 Strobe Reset Shutter Dimmer Color Wheel 1 Color Wheel 2 Pan Tilt Pan Fine Tilt Fine Pan amp Tilt Speed Vector Mode Iris Fixed Gobo Wheel Rotating Gobo Wheel Gobo Rotation Focus Zoom Prism Prism Rotation Color Marcos Gobo Marcos Ve
13. m AC power before removing or installing the lamp fuses or any part and when not in using 2 Always make the fixture connected to the ground electrically 3 Please stop using when it is very hard to use and check the problem with our agent or factory 4 If lamp on off by controller please pays attention to the voltage depressed when open a lot of light in one time 5 Using Electromagnetic ballast the second time to open the light should be after I5minite from the first time electronic ballast have hot start up function 6 Don t expose the fixture to rain or moisture STRUCTURE 1 Through light hole Light body 3 Arm Beam plank AR WN N A 5 Cover EAGLE 1008 HMI 575W moving head spot is powerful in functions with CE Standard It has been tested through frequent practice in different cases and well recognized by professional designers in the field of stage light It has become one of the most popular moving head spots This equipment provides high luminance spot effects which impress people greatly It can be used in all kinds of scenes which need high quality lighting TECHNICAL PARAMETER VOLTAGE Magnetic Ballast AC 120V 60Hz LAMP HMI 575W POWER CONSUMPTION Magnetic Ballast 775W COLOUR SYSTEM 2 colour wheels 14 interchangeable colours white half colour effect bi directional rainbow effect at variable speed GOBOS Fixed gobo wheel 8 fixed gobos white gobo shake function Rotating gobo whee
14. ng 184 188 GOBO 2 No rotating 189 193 GOBO 1 No rotating 194 198 White 199 219 GOBO Animation Fast to Slow 220 240 GOBO Animation Slow to Fast 241 255 Random Gobo CHANNEL 12 ROTATING GOBO WHEEL DMX 512 VALUE 0 255 FUNCTION 0 127 Clockwise Revolve Slow Fast 128 252 Anticlockwise Revolve Fast Slow 253 255 Not Rotation CHANNEL 13 GOBO ROTATION DMX 512 VALUE 0 255 FUNCTION 0 127 Clockwise Revolve Slow Fast 128 252 Anticlockwise Revolve Fast Slow 253 255 Not Rotation CHANNEL 14 FOCUS DMX 512 VALUE 0 255 FUNCTION 0 255 Linear focusing CHANNEL 15 ZOOM DMX 512 VALUE 0 255 FUNCTION 0 255 Linear Amplify CHANNEL 16 PRISM DMX 512 VALUE 0 255 FUNCTION 0 31 White 32 255 PRISM CHANNEL 17 PRISM ROTATION DMX 512 VALUE 0 255 FUNCTION 0 127 Angle adjustment 128 191 clockwise Revolve Fast Slow 192 255 Anticlockwise Revolve Slow Fast CHANNEL 18 COLOR MACROS DMX 512 VALUE 0 255 FUNCTION 0 15 None 16 95 Color 1 Slow Fast 96 175 Color 2 Slow Fast 176 255 Color 1 2 Slow Fast CHANNEL 19 GOBO MACROS DMX 512 VALUE 0 255 FUNCTION 0 95 None 96 175 Slow Fast 176 255 Slow Fast CHANNEL 20 VECTOR MODE DMX 512 VALUE 0 255 FUNCTION 0 251 Not vector 252 255 Color Rotating gobo Prism Vector DMX PR
15. rge under the high voltage CE ZA WARNING HOT A gt 2 TURN 4 SCREWS O REPLACE THE LAMP 15 Power supply mains Use the provided plug to connect the main power to the projector paying attention to the voltage and frequency marked on the panel of the projector It is recommended that each projector be supplied separately so that they may be individually switched on and off Important It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Power consumption of this projector is 200VA Watchdog system When the projector is switched on the electronics performing a reset this function moves the head to an extreme limit point and rotates the internal color and gobo wheels thus allowing the microprocessor control system to register the positions of all motor under its control When the lamp strikes and fires up it can create some noise within the projector that has the potential to disturb the microprocessors This projector is fitted with an electronic watchdog system that monitors the microprocessor and will initiate a reset if the functioning of the microprocessor has been disturbed This system ensures that the reset is performed successfully and once completed the projector is ready to receive control instruction and operate without problem MA DMX X EN C A t 7 7 _ A j 3 3 o oH DMX i o o J A i 72 7
Download Pdf Manuals
Related Search