Intellian K4/K6 Serial Number Notice All Right
Contents
1. Intellian K4 K6 Serial Number This serial number will be required for all troubleshooting or service calls made regarding this product Notice All Right Reserved Intellian K4 K6 and Intellian are the registered trademarks of Intellian Technologies Inc and should not be appropriated without permission by Intellian Technologies Inc and the information contained in this manual is the property of Intellian Technologies Inc Any and all parts of this manual shall not be reproduced and distributed in any form without prior written consent by Intellian Technologies Inc The information contained in this manual shall be subject to change at any time without notice due to the functional upgrades of the product Copyright Intellian Technologies Inc Doc No K4 K6 AC V101 CONTENTS INTRODUCTION ee ice ace ene 1 INTRODUCTION TO INTELLIAN KAIK ccc cceecccceeecccesscccesscceescccceeccceuecceuseceees 1 FEATURES OF INTELLIAN K4 K6 wu ccc ee cc ceeceeeccceccccecccescccscccccccnsccesccesceesceesecenes 2 BASIC SYSTEM CONFIGURATION cecesccescesdesecectesecsscscctesccsnccsesctececstesedenseseenocsecens 3 INSTALLATION oovsatevedaccccsastecdcncctesncecscoscsdececkacescccabssedestecsexecascdesatdacasucesexcdesseons 4 SYSTEM COMPONENTS EE 4 TOOLS REQUIRED FOR INSTALLATION ccccccsecccecccscccsccceeceesccesceusceeesceeueceees 7 PLANNING THE INSTALLATION EE 8 INSTALLING THE DA CW siscccceccicesicecccscac2. 34 K4 K6 Satellite Antenna System Install and User Manual Setting the Antenna Parameters It is not recommended for a novice satellite service user to use this mode Consult Intellian for changing antenna parameters SETUP MODE O 1 Press YES to enter setup mode YES NO O O SET SAT PAIR PREV YES NEXT O O O KE 2 Press NEXT three times to enter set antenna parameter mode 3 Press YES to set antenna parameter SET ANT PARAMETER PREV YES NEXT O f O 4 Select the PARAM SCAN OFF Q PREV Shows previous parameter O SELECT Set the displayed parameter NEXT Shows next parameter Press ENTER to move to next screen 5 Inputthe WRS LEVEL t increases the value decreases the value Change the underscored digit using the buttons O o O Press INPUT to accept the value and move to next K digit Press BACK to move to previous digit Press ENTER to move to next screen WRS LEVEL 0500 GC INPUT ech 6 Press YES to save the inputinformation Press NO to cancel and retum to main setup mode Operation Using the DACU 1 Parameter Setting method SCAN OFFSET The actual angle between the marked pointon the sub reflector and the datum TRACK SCALE To control the tracking speed while antenna is tracking the satellite High Track Scale value resulting in high tracking speed DETECT LEVEL The basic single detection level TRACKING LEVEL
3. To change frequency information of the antenna 62 K4 K6 Satellite Antenna System Install and User Manual Move Antenna and Execute Antenna Diagnosis ETE a Diagnosis The antenna current position a gt TREY serial Comm Garsa arsa OD AZ Limit ow Mt EL Limiti Go to Position Sub Fteflector Diagnosis results _ LNB TEM GI Cen Farwen Bet GET N corer Conson Go te Target Position N Diageestis Target angle to go to Fkt Tee Move Step Move the antenna in four JALA i i directions SATB Skew Information Gel ita e Angle of Antenna Two kinds of antenna movement is available One is to move to the target position and the other is to move by certain amount of angle The current position angle of the antenna is displayed as Current and to move to the target position push Go to target Position button after keying in desired angle into Target To move to a certain amount of angle only move antenna to direction of up or down and CW or CCW by using E Lg F buttons after keying in the desired angle into the AZ and EL in the Mover Step box Rotate LNB to direct the skew angle by using zl button Self Diagnosis If Diagnosis button is pressed to carry out self diagnosis of antenna it displays the result of self diagnosis after carrying it out Blue circle means the antenna is normal red represents abnormal and green represents the antenna is under diagnosis Command Butt
4. 1 Refer to the drawing A 2 Rotate antenna left and right slowly till the limit switch is pressed WARNING Don t rotate it quickly or you may damage the antenna limit system 3 Turn the antenna by 360 to the reverse direction 4 Insert the sponge in both sides of the dish to fix the pedestal in position with the bottom radome 5 Cover upper part of Radome being careful for it s not touching the reflector and then assemble upper part of radome 6 Pack Intellian K4 K6 into the original package box d Shipping Restraint Bottom of the radome y Shipping Restraint Warranty 67 Warranty This product is guaranteed by Intellian Technologies Inc against defect due to faulty workmanship or materials and this guarantee covers for 2 year parts and 1 year labor for labor performed at Intellian Technologies Inc service center from the date of purchase of the product You are requested to present a copy of the purchase receipt issued by Intellian Technologies Inc that presents the date of purchase for after sales service under warranty In case of failure to present the date of purchase the warranty period is to be calculated to 30 days after the manufacturing production date If you discover a defect Intellian Technologies Inc will at its option repair replace or refund the purchase price of the product at no charge to you provided you return it during the warranty period transportation charges pr
5. Operating voltage Antenna system performance Ka band 18 3 20 2GHz 680 5 90 Elevation range Roll 25 Pitch 15 Roll and pitch response rate 45 per second 45 per second Appendix K4 Technical specification General Approvals CE conforms to FCC verified to Dimensions Satellite antenna unit Antenna dish diameter Antenna control unit Weight Satellite antenna unit Antenna control unit Environmental Operating temperature range Storage temperature range Humidity limit Operating voltage EU Directive 89 336 EEC CFR47 Part 15 50cm 19 7 x 54cm 21 2 45cm 17 7 17 8cm 7 x21 6cm 8 5 x5 38cm 2 1 11 6kg 21 5 Ibs 1 2kg 2 6 Ibs 15 C to 55 C 25 C to 70 C 95 R H 90 260 V AC Antenna system performance Frequency Ka band 18 3 20 2GHz Azimuth range 680 Elevation range 0 90 Roll 25 Ship s motion Pitch 15 Roll and pitch response rate Turn rate 50 second 50 second 70 K4 K6 Satellite Antenna System Install and User Manual Intellian Technologies Communicate Smarter Intellian Technologies Inc HQ Dongik Building 7th FI 98 Nonhyun Dong Gangnam gu Seoul 135 010 Korea Tel 82 2 515 4923 Fax 82 2 545 4903 Factory SK Ventium 104 501 522 Dangjeong Dong Gunpo Si Kyunggi Do 435 776 Korea Tel 82 31 436 1488 Fax 82 31 436 1489 R amp D Cent
6. 1 Press YES to enter setup mode SET GPS O 3 Press YES to set GPS PREV YES NEXT O O A O 4 Inputthe longitude data pea mace ae Yon increases the value decreases the value ke Change the underscored digit using the buttons O D O A Press INPUT to accept the value and move to next digit Press BACK to move to previous digit 5 Press ENTER to move to next screen EONS AVE Hra E O Press BACK to move to previous screen INPUT We LU O O ba 6 Input the latitude data increases the value decreases the value Change the underscored digit using the buttons Press INPUT to accept the value and move to next digit Press Back to move to previous digit LATITUDE Zi ANN INPUT O 7 Press YES to accept data Press NO to cancel and retum to main setup mode Operation Using the DACU 39 Setting the DiSEqC Method DiSEqC selection can be made from ACU It is not recommended for a novice satellite service user this mode 1 Press YES to enter setup mode ETUP MODE En San PAIR S 2 Press NEXT five times to enter DISEQC mode EV YES 3 Press YES to use DISEQC 4 Select the DiSEqC Method PREV Shows previous DiSEqC Method SELECT ENTER Set the displayed DiSEqC method NEXT Shows next DiSEqC Method Press ENTER to move to next screen DO NOT USE PREV SEI 5 Pre
7. ACU el ki f B Band Converter 8 SE AC Power Cable Installation Intellian K4 K6 Connect the RF1 Cable Yellow 15m from the RF 1 connector on the antenna to the RF1 connector at Ka band Antenna In section on the rear of DACU Connect the RF2 Cable Green 15m from the RF 2 connector on the antenna to the RF2 connector at Ka band Antenna In section on the rear of DACU Connect the Power Cable Red 15m from the Power connector on the antenna to the Power Data connector at Ka band Antenna In section on the rear of DACU Intellian i4 i6 Connect the RF1 Cable Black 15m from the RF 1 connector on the antenna to the RF1 connector at Ku band Antenna In section on the rear of DACU Connect the RF2 Cable White 15m from the RF 2 connector on the antenna to the RF2 connector at Ku band Antenna In section on the rear of DACU Receivers Connect the B Band Converter not supplied to the RF connector on the rear of the receiver Connect the DACU IRD Cable 3m from the RF1 connector at To Receiver Section on the rear of the DACU to RF connector on the B Band Converter Connect USB cable 1 8m from the USB1 connector at To Receiver Section on the rear of the DACU to the USB connector on the receiver Connect the AC power cable 1 5m from AC power connector on the rear of DACU to a power source from 90 260 V AC Press the POWER ON switch on the rear of the DAC
8. BACK to exit setup mode 3 Press Yes to set the satellite pair Operation Using the DACU 29 Setting the Satellite Pair You can change the satellite pair if you decide to receive satellite television service from a different service provider Example1 Changing the target satellite without using DiSEqC O 1 Press ENTER to enter setup mode YES NO Qa O O L eet 2 Press YES to set satellite pair 3 Press YES to set triple satellites 4 Set satellite A Press PREV to show previous satellite name Press SELECT to set chosen satellite to SATA O O Press NEXT to show next satellite name SAT A DTV101 PREV SELECT NEXT O 5 Set satellite B Press PREV to show previous satellite name Press SELECT to set chosen satellite to SAT B O O Press NEXT to show next satellite name SAT B DTV110 O PREV SELECT NEXT 6 Set satellite C Press PREV to show previous satellite name Press SELECT to set chosen satellite to SAT C Press NEXT to show nextsatellite name SAT C DTV119 PREV SELECT NEXT O 7 Press YES to save selections Press NO to cancel and retum to main setup mode 30 K4 K6 Satellite Antenna System Install and User Manual Example2 Changing the target satellite using DiSEqC GE O 1 Press YES to enter setup mode YES NO O H O K QO SET SAT PAIR O PREV YES NEXT O 2 Press YES to set
9. Definition Channel Availability DIRECTV Ka band signal reception for 99 W and 103 W satellites which are currently broadcasting more than 130 national HD channels Dual Antenna System Enjoy watching channels from DIRECTV Ku band satellites 101 W 110 W and 119 W and Ka band satellites 99 W and 103 W simultaneously just like a home system using Intellian s exclusive dual antenna system Wide Range Search WRS Algorithm Since the Ka band signal has a very narrow beam width the searching time can be extended if the antenna system is using the conventional searching method to search only the main lobe Intellian s patent pending technology WRS can ultilize the side lobe of the Ka band signal and jump onto the main lobe directly which will shorten the searching time significantly Dynamic Beam Tilting DBT Technology An advanced tracking technology is required for tracking the very narrow beam width of the Ka band signal The DBT patent pending technology allows the K4 K6 to have the most relibable and accurate tracking capability while the vessel is cruising at high speed or in rough sea conditions New Rack Mount Dual Antenna Control Unit DACU DACU controls dual antenna systems at one time switches channels freely amongst DIRECTV s 5 satellites using TV remote control and includes built in HD and MIM modules Easily connects up to 8 receivers directly from different rooms without any extra multi switches and wiring t
10. Inputthe tracking frequency MHz and symbol rate KHz for vertical high band 13 Inputthe network ID NID for vertical high band VER HIGH NID 0x0003 O INPUT O QO kV O HOR HIGH 12523 21096 QO INPUT O O A O 14 Inputthe tracking frequency MHz and symbol rate KHz for horizontal high band Operation Using the DACU 33 HOR HIGH NID 0x0003 le 15 Ae network ID NID for horizontal high INPUT K O D O ee 1 H Eee 16 ener verification method of tracking PREV SELECT NEXT EH PREV Shows previous method 2 Li QO SELECT Set the displayed method K NEXT Shows next method VOLTAGE AUTO O 17 Selectthe voltage supplymethod to LNB PREV SELECT NEXT O AUTO recommended O A O 18 Selectthe DISEQC method DISEQC ONLY 22KHZ O o mm D O O 19 Press YES to save the input information Press NO to cancel and return to main setup mode 1 Verification method SIGNAL use only signal level for tracking DVB LOCK use only DVB Lock signal for tracking DVB DECODE verify satellite using DVB decoding method for tracking DSS DECODE decode only DSS Lock signal for tracking 2 Voltage supply method AUTO change voltage to LNB by IRD voltage ONLY 13V always supply 13V to LNB ONLY 18V always supply 18V to LNB 3 DISEQC method AUTO change signal to LNB by IRD DISEQC ONLY OKHZ always supply OkHz to LNB ONLY 22KHZ always supply 22kHz to LNB
11. InstallShield already successfully to installed PL 2303 d USB to Serial driver Please press Finish button to close and Interface on the font of DACU out of InstallShield e Ka USB Interface To upgrade K4 K6 system or To operate GUI program e Ku USB Interface To upgrade i4 i6 system or To operate GUI program If you have been plugged cable on PC before run this setup please unplug and then plug cable again for system detect this e MIM USB Interface To upgrade MIM system devicel Baal Apdo Carel Urin Ka K4 K6 MIM ku i4 i6 3 Execute GUI program by inserting the CD ROM supplied into the 3 Execute the GUI Program in the same supplied CD ROM to start the CD ROM drive of the computer operation Refer to p 51 4 After turning on the power of the DACU if the blue status circle does not change to Search or Tracking from Initialize then you have to change the PC Interface terminal of ACU for PC program use rather than GPS use Operation Using PC Contoller Program 53 Connects a PC with Ka K4 K6 USB Interface Zeg Anterag GPS and Find Amiensa Angle Sed Satellite Informetian Zen Tracking Inloimetan of Sesciine Primary Sel Tracking Inlemm span of Sellie Feceadapd Bove Aniones Estee Diegnonie Sel Amema Parameters for Central Qisplirg Parametess tor Erginer z Situs Pesta Seon Track sat Sewp inftialire Ke Leet pa fei Rae tamatan Setup Gi
12. Satellite Antenna System Install and User Manual Setting the factory default parameters Initialize all of the antenna information to the factory set up ETUP MODE SET SAT PAI ES EFAULT ES NE 1 Press YES to enter setup mode 2 Press NEXT fourteen times to enter Default setting mode 3 Press YES to set default parameters Operation Using PC Contoller Program 51 52 K4 K6 Satellite Antenna System Install and User Manual Installation USB to Serial Driver OPERATION USING PC Controller Program 1 Execute RL2303 Driver Installer exe by inserting the supplied CD ROM into Introduction the CD ROM drive of the computer GUI Software of Intellian K4 K6 has been coded for the user to easily set up the antenna by using the user s personal computer Using the GUI program enables the user to easily monitor and modify the information of antenna satellite and GPS Additionally the detail diagnostic method of the antenna is provided by the GUI program WARNING Before starting this GUI program please install the USB to Serial Driver by inserting the supplied CD ROM Refer to p 52 2 Press NEXT or YES button to complete the installation To start this GUI program InstallShield Wizard 1 Connect one end of USB cable to the USB connector on the computer InstallShield Wizard Complete 2 Connect the other end of the USB cable AB Type to the USB
13. The basic signal tracking level ELADJUST The mechanical tolerance compensation of elevation limit WRS LEVEL The basic WRS detection level POWER THRESHOLD The value to identify Vertical Horizontal or RHCP LHCP DISEQC LEVEL The value to identify 22KHz tone OFFSET RH LH The difference value between RHCP LHCP and SCAN OFFSET USE WRS To apply WRS while antenna is searching for satellite OFFSET DIFFERENCE To apply Offset Difference 35 36 K4 K6 Satellite Antenna System Install and User Manual Setting the LNB local frequency It is possible to select a local frequency from DACU It is not recommended for a novice satellite service user to use this mode CASE 1 Single band LNB is used Press YES to enter setup mode SETUP MODE O YES NO O O O SET SAT PAIR CH 2 Press NEXT four times to enter set local frequency PREV YES NEXT O mode O O SET LOCAL FREQ 3 Press YES to set local frequency PREV YES NEXT O O O 4 Select the LNB Type SINGLE PREV Shows previous LNB type SELECT Set the displayed LNB type O O t NEXT Shows next LNB type Press ENTER to move to next screen LNB TYPE SINGLE O PREV SELECT NEXT LOCAL FREQ INPUT D EMHZ 5 Inputthe local frequency of LNB LA increases the value decreases the value Change the underscored digit using the buttons Press INPUT to accept the val
14. are now carrying the majority of DirecTV s HD programming This powerful and innovative design of the Intellian K4 K6 incorporates a plug and play system to control and support the Ku band and Ka band dual antenna system which allows the users to enjoy both DIRECTV HD channels and standard channels at the same time The Intellian automatic and fully integrated dual antenna system offers users not only the simplest installation but also the most comfortable entertainment environment As if at home all a user needs to do is just switch the channel buttons on the TV remote control Then Intellian s dual antenna system will automatically recognize where the selected channel is located between Ku and Ka band and change the satellite if necessary In addition the Intellian K4 K6 19 inch rack mount Dual Antenna Control Unit DACU allows for a hassle free installation with its standard 8 receiver connector ports This means that up to 8 receivers can be connected to the ACU from different locations on the vessel without additional multi switches and wiring Not to mention the Ku band HD module and Multi satellite Interface Module MIM are both embedded in the DACU which enables users to switch channels freely and simultaneously amongst DIRECTV s 5 satellites 2 for Ka band 99 W and 103 W and 3 for Ku band 101 W 110 W and 119 W K4 K6 Satellite Antenna System Install and User Manual Features of Intellian K4 K6 Full HD High
15. name PREV Shows previous satellite name SELECT Select the displayed satellite for editing NEXT Shows next satellite name Press ENTER to move to next screen SAT NAME DTV101 PREV SELECT ech 5 Input the satellite name SAT NAME DTV101 Increases the value decreases the value INPUT Press INPUT to accept the value and move to next digit Press BACK to move to previous digit 6 Press ENTER to move to next screen Press BACK to return previous screen SAT NAME DTV101 INPUT O KL LONGITUDE 124 00 E INPUT O Q A KL 7 Inputthe satellite position increases a value decreases a value Change the underscored digit using the buttons Press INPUT to accept the value and move to next digit Press BACK to move to previous digit Change the underscored digit using the buttons 32 K4 K6 Satellite Antenna System Install and User Manual VER LOW 12598 21096 Q INPUT K O A O VER LOW NID 0x0003 O 9 Input the network ID NID for vertical low band INPUT O O H O HOR LOW 12523 21096 O INPUT O 8 Inputthe tracking frequency MHz and symbol rate KHz for vertical low band 10 Inputthe tracking frequency MHz and symbol rate KHz for horizontal low band O H L HOR LOW NID 0x0003 O 11 Input the network ID NID for horizontal low band INPUT O O H O VER HIGH 12598 21096 O INPUT O QO A QO 12
16. satellite pair O 3 Set satellite A Press PREV to show previous satellite name Press SELECT to set chosen satellite to SATA Press NEXT to show next satellite name SAT A DTV101 PREV SELECT NEXT O 4 Set satellite B Press PREV to show previous satellite name Press SELECT to set chosen satellite to SAT B Press NEXT to show next satellite name SAT B DTV119 PREV SELECT NEXT O 5 Set satellite A when DiSEqC is active from IRD Press PREV to show previous satellite name Press SELECT to set chosen satellite to SAT A Press NEXT to show next satellite name SAT A DTV101 PREV SELECT NEXT O 6 Set satellite B when DiSEqC is active from IRD Press PREV to show previous satellite name Press SELECT to set chosen satellite to SAT B Press NEXT to show next satellite name SAT B DTV119 O PREV SELECT NEXT O 7 Press YES to save selections Press NO to cancel and retum to main setup mode Operation Using the DACU 31 Edit Satellite information It is possible to modify the existing satellite information and input new satellite information into the ACU as well It is not recommended for a novice satellite service user to use this mode SETUP MODE O YES NO O A O O 1 Press YES to enter setup mode GET SAT PAIR 2 Press NEXT twice to enter edit satellite info mode PREV YES NEXT O O enh Gan INFOS 3 Press YES to edit satellite info PREV YES NEXT O 4 Set the satellite
17. the self tapping screws supplied attach the mounting brackets to the sides of the DACU 3 Place the DACU in the location where it is going to be installed 4 Connect the cables to the rear of the DACU 5 Using a pencil to mark the 4 hole positions 2 each side and use the appropriate drill bit to drill them b 19 Rack Mount Type 1 The DACU should be installed using the two supplied Rack Mounting Brackets which allow for a side 19 rack mounting configuration 2 Using the self tapping screws supplied attach the mounting brackets to the sides of the DACU 3 Place the DACU in the location where it is going to be installed 4 Connect the cables to the rear of the DACU 5 Using a pencil to mark the 8 hole positions 4 each side and use the appropriate drill bit to drill them Installation 17 a Table Mount Type b 19 Rack Mount Type 18 K4 K6 Satellite Antenna System Install and User Manual Connecting the System Cables After installation and fixation of the antenna connect the DACU to the antenna Refer the drawing below to connect cables WARNING It will cause a critical malfunction if you do not follow the system diagram to complete the system cable connections as below Single and Multi IRD Connection K4 K6 i4 i6 ee SI RPI RP u Power Cable Red RF2 Cable Green RF1 Cable Yellow RF1 Cable Black EEE TT Se RF2 Cable White Dual
18. B Universal Band Antenna in use of universal LNB Set Local Frequency To select local frequency of LNB 58 K4 K6 Satellite Antenna System Install and User Manual Load and Update Default Command Button 1 Load Default Click load default button to select rif file according to your region VYertication mi Onby op of Satel tule Diemnd 5 SD 9 tellin Antenna PC Controller Lack Unby r for Cont z Region info_Asia_1 O rif Decode a Region Info Ewope l 0 rif J Region ln Jopen TU ot Deca t Region ln Kaa 1U rii Higeon kio North Aare 1 0 ril Satellite Mo perch Si Rirgion bin South America L L gt racking iialize eer Dei ON Rngion ini Moth Aepcngca 10 rif wm Ben nwrap i dod DIS Bach MIF Files rit KE E E etup Bete leepMoade Load Update Hina Default Default KDEA KEE 2 Update Default Click Update default button to open update default Dialogue Click yes button to update the system 2cute Diagnosis ters for Control C COMI C COM D COM2 C COM6 C COM3 C COM IS Tile oto lite Search Intellian Antenna PC Controller Tracking Do you want to update default set Region Info North Ametca 1 Dt Initialize ees TE OLIEN Unwrap Setup SleepMode Load Update Comm Default Default 3 Click confirm yes button to complete the update ters for Control is Tracking Satellite Edit Satellite Information Search Intellian Antenna PC Contro
19. DTV103 SETUP O O O O 4 The antenna has located the satellite andis now TRACKING A DTV99 O tracking B DTV103 SETUP O O O O 24 K4 K6 Satellite Antenna System Install and User Manual Start Up i4 i6 1 Communication is being established between the ALIZE ACU O E AN 6 ER e antenna and the DACU The DACU initialized 2 The antenna is initialized TIALIZE ANTENNA NTELLIAN i6 HD SEARCH 3 The antenna is searching for Satellite A DTV110 4 The antenna has located the satellite and is now tracking WARNING The operation method is exactly same for both K4 K6 and i4 i6 The below instruction will be explained using the i4 i6 as example Operation Using the DACU 25 Change of Target Satellite Your antenna is programmed with three candidates of target satellites as default mode To change the target satellite press LEFT soft key The target satellite is changed and is automatically tracked by the antenna 1 Press LFET soft key for tracking Satellite B 2 The antennais tracking Satellite B 3 Press LFET soft key for tracking Satellite C TRACKING C DTV11 O 4 The antennais tracking Satellite C DTV101 DTV11 E O 26 K4 K6 Satellite Antenna System Install and User Manual Monitoring the current status of the antenna While POWER ON DACU displ
20. EL HH H O EXIT O O O 5 Move the antennain the elevation EL axis UP Move the antenna up DOWN Move the antenna down EXIT Return to Antenna Move Step mode 6 Press YES to move the antenna to input position Operation Using the DACU 45 7 If failed to press same key twice TRY AGAIN will be displayed ED TRY AGAIN O O O 8 If failed to register a free key KEY IS USING will be displayed 9 REMOTE KEY REGISTED will be displayed if key has been properly registered 10 Press NEXT to shows next function Press EXIT to return to main setup mode 1 Function CHANGE SAT Change the target satellite SLEEP MODE Enter sleep mode CLEAR REGISTERED KEY Clear registered key 46 K4 K6 Satellite Antenna System Install and User Manual Setting Multi satellite Interface Module MIM Up to 8 IRDs can be connected to DACU and every IRD connected to DACU can be a Master which can change the target satellite freely by selecting a channel Follow the steps below to enable disable this function 1 Press YES to enter setup mode SETUP MODE O YES mo JO O Ki 2 Press NEXT eleven times to enter the set MIM SET SAT PAIR O mode PREV YES NEXT O O SET MIM 3 Press YES to set MIM PREV YES NEXT O 4 Press ON Press ENTER to m
21. Find Angles amp Skew Antenna GPS Finds the current antenna angles and Skew angle in relation to the longitude of satellite and GPS Find Angles amp Skew City GPS Finds the current city angles and Skew angle in relation to the latitude of satellite and GPS 60 K4 K6 Satellite Antenna System Install and User Manual Set Tracking Information of Satellite Primary Satellite to be edited VERTICAL RHCP t Satellite information for Vertical amp Low band Low i Satellite information for Horizontla amp Low band gt Satellite information for Vertical amp High band Satellite information for Horizontal amp High band Power supplying method iaa Sarir beleen DiSEqC using method Command Button e Edit Satellite Information To change frequency information of the antenna e Satellite Information Satellite information consists of frequency symbol and NID Network ID of a transponder in tracking satellite There are four groups of satellite information Vertical RHCP is applied when IRD supply 13V and Horizontal LHCP is applied when IRD supply 18V LOW is applied when DiSEqC signal is not detected from IRD HIGH is applied when DiSEqC signal is detected from IRD If you select Not Use or Change Satellite two HIGH groups are inactivated If you select Change Band two High groups are activated and you can modify satellite information which
22. NB is tested If failed check the LNB and control board Skew System tested If failed check the control board skew motor and skew sensor Antenna Input Power tested If failed check the RF cable ACU Power tested If failed check the ACU power cable and Input DC power IRD Power tested If failed check the ACU to IRD cable and IRD power RESULT STATUS is pass Numberis fail 3 8 And Is Testing Operation Using the DACU Setting Region SETUP MODE O YES wo JO O O SET SAT PAIR O PREV YES NEXT O O LOAD REGION INFO O PREV YES NEXT O O O CONTINENT N AMERICAC P CT NEXT O REV SELE O Lal O REGION NEW YORK O PREV SELECT NEXT O LOADING JIH DO NOT TURN OFF O O 1 CONTINENT 49 Press YES to enter setup mode Press NEXT thirteen times to enter Load Region Information mode Press YES to load region information Select the continent PREV Shows previous continent SELECT Set the displayed continentfor editing NEXT Shows next continent Select the region PREV Shows previous region SELECT Set the displayed region NEXT Shows next region Press YES to load region info Press NO to cancel and retum to main setup mode Loading selected region info N AMERICAN S AMERICAN EUROPE ASIA 2 REGION New York Miami UK JAPAN 50 K4 K6
23. U to start the operation of the antenna system automatically K4 K6 Satellite Antenna System Install and User Manual Connecting the system to a GPS For improved satellite tracking you can connect your satellite TV system directly to your boat s NMEA 0183 GPS system To do this you will need lengths of cable suitable for connecting to your GPS system and the green 2 way DACU GPS connector supplied with your Intellian K4 K6 Satellite TV System To connect the system to a GPS 1 Strip back the insulation of each cable and connect a cable to each terminal of the 2 way connector 2 Tighten the locking screws 3 Connect the cable from the ve positive terminal of the DACU GPS connector to the NMEA OUT wire of the boat s GPS system 4 Connect the cable from the ve negative terminal of the DACU GPS connector to the ground wire of the boat s GPS system 5 Refit the DACU GPS connector to the rear of the DACU NMEA out Ground Installation 21 Target Satellite Setting You can select the target satellite to receive satellite signal from If the target satellite is not on the list you will have to register the target satellite GPS Setting You can input the GPS information through the DACU or the PC Program To setting the GPS information the antenna system has to be in SET UP mode For detailed instructions please refer to page 38 Setting the GPS and page 59 Set Anten
24. ays the status of the antenna The various DACU displays may be shown according to the current status of the antenna SEARCH A DTV101 O DTV110 DTV119 O O O TRACKING A DTV101 O DTV110 DTV119 O kd O O ANTENNA IS UNWRAPING O DTV110 DTV119 O O O O TRACKING A DTV101 DTV110 DTV119 Q QO EI AZ EL 0 SIGNAL VL O O e QO O eet O O e O 1 The antennais searching for Satellite A 2 The antenna is tracking Satellite A 3 The antenna is unwrapping the cable 4 The antenna is again tracking satellite A Press center soft key to display position detail 5 Antenna position detail and signal strength are displayed 6 Press center soft key to display current GPS information Press center soft key to return to main tracking mode Operation Usi Sleep M ng the DACU ode 27 If the antenna lost the tracking satellite in sleep mode sleep mode is cancelled TRACK NG A DTV DTV110 O O 1 Press BACK to enter sleep mode 2 Press Back again for exiting sleep mode 28 K4 K6 Satellite Antenna System Install and User Manual Set Up Mode Begin Set Up Mode To enter the Set up Mode simply follow the instructions below TRACK NG DTV110 SET SAT PAT ES ETUP MODE A DTV1 1 With the antenna tracking 2 Press ENTER to enter setup mode Press
25. dar units can overload the antenna a front end circuits Make sure that your antenna is installed as described in page 8 Selection of Installation Site 5 Incorrect or loose RF connectors As part of the regular maintenance recommended by Intellian Technologies Inc all connections should be checked to ensure that they have not become loose A loose RF connector can reduce signal quality 6 Multi switch interference If you have multiple satellite receiver IRD connected to your system make sure that you are using an active not passive multi switch Trobleshooting 65 7 Satellite receiver IRD troubleshooting Your satellite receiver IRD may be the cause of less than ideal operation 1 Check the satellite receiver s IRD s configuration to ensure that it is programmed for the area in which you are operation 2 Unplug the satellite receiver IRD from the power supply for 1 second Reconnect and allow the system to initialize 8 LNB fault If you have an LNB fault it may require replacing Contact your local dealer national distributor or Intellian Technologies Inc product support for further assistance 66 K4 K6 Satellite Antenna System Install and User Manual Preparation for Transportation This is to describe how to fix the antenna internally for transportation and the following procedures to fix antenna shall be strictly observed to protect it from being damaged during transportation
26. e connector m W La Fr E 11mm Spanner Antenna Unit A DEI Cabl lt _ RF 2 Cable Power Cable WARNING Do not use excessive force when using the spanner this will damage the threads Be careful that the connectors do not contact the mounting surface of the antenna this may cause a critical malfunction and serious damage to the equipment Mounting the antenna Attach the antenna by using the hex head bolts M8X50L M8 spring washers and M8 flat washers supplied gm lt 4 Antenna Unit Support lt 4 Deck 4 M8 Flat Washer M Spring Washer lz M8 Hex Bolt i ae 13mm Spanner Installation 15 Installing the DACU DACU dimensions 47 32 cm 18 6 45 32 cm 17 8 43 cm 16 9 26 58cm 10 5 48 43cm 19 4 37cm 1 7 46 5cm 18 3 Selection of Installation Site The DACU should be installed below deck in a location that is e Dry cool and ventilated e Easy accessible from your main TV viewing area 16 K4 K6 Satellite Antenna System Install and User Manual To Install the DACU Intellian supplies two type of mounting methods a Table Mount Type and b 19 Rack Mount Type to mount your DACU a Table Mount Type 1 The DACU should be installed using the two supplied Table Mounting Brackets which allow for a top or bottom mounting configuration 2 Using
27. ed for securing the antenna unit and DACU to your boat Antenna i Tapping i FlatHead i i Hex Nut i Screw 1 Screw i Bolt f 5EA i 4x16L M3x8L M3x12L i SEA i 10EA 5EA i Hex Head i i Spring i Wrench Bot Washer Washer i SEA i 10EA SEA Hex Bolt 5EA Gmpoe se ow Rack Mounting Bracket a Table Mounting Braet e rage J e j C spring Washer J vwe a saco y o a Cwen a Kalk Moning Template a Gut nstalaton pe Im Installation Tools Required for Installation IN 11mm Spanner Power Drill Cross Head 13mm Spanner Screwdriver N 10mm Drill Pencil d m 5mm Hole Saw Allen key 8 K4 K6 Satellite Antenna System Install and User Manual Planning the installation Selection of Installation Site Install the antenna in accordance with the following procedures to insure maximum performance of the antenna The ideal antenna site has a clear view of the horizon satellite all around Please be sure there are no obstacles within 15 degrees above the antenna va Any obstacles located above a 15 L degree elevation can prevent the Intellian NGS antenna from tracking the satellite i j Pa signal Refer to the drawing Antenna Unit Obstacle Keep the antenna out of line with nearby radars as their energy levels may overload the antenna front end circuits If necessary position the antenna unit so it is at least four feet 1 2 meters ab
28. epaid to the factory direct Please attach your name address telephone number a description of the problem and a copy of the bill of sale or sales receipt as proof of date of original retail purchase to each product returned to warranty service Alternatively you may bring the product to an Authorized Intellian Technologies Inc dealer distributor for repair This Limited Warranty does not apply if the product has been damaged by accident abuse misuse or misapplication or has been modified without the written permission of Intellian Technologies Inc if any Intellian Technologies Inc serial number has been removed or defaced or if any factory sealed part of the system has been opened without authorization 68 K4 K6 Satellite Antenna System Install and User Manual General CE conforms to Dimensions Satellite antenna unit Antenna dish diameter Dual Antenna control unit Weight Satellite antenna unit Environmental Operating temperature range Storage temperature range Humidity limit Frequency Azimuth range Ship s motion Turn rate Appendix K6 Technical specification Approvals EU Directive 89 336 EEC FCC verified to CFR47 Part 15 70cm 27 5 x 72cm 28 3 60cm 23 6 43cm 16 9 x26 58cm 10 5 x4 37cm 1 7 20kg 44 Ibs 4kg 8 8 Ibs Dual Antenna control unit 15 C to 55 C 5 F to 131 F 25 C to 70 C 13 F to 158 F 95 R H 90 260 VAC
29. er SK Ventium 104 601 522 Dangjeong Dong Gunpo Si Kyunggi Do 435 776 Korea Tel 82 31 436 2280 Fax 82 31 436 2284 Intellian Technologies USA Inc 9261 Irvine Blvd Irvine CA 92618 USA Tel 1 949 916 4411 Fax 1 949 271 4183 E Mail customersupport Intelliantech com Homepage http www Intelliantech com
30. er installation using the DACU or PC controller program and includes the following functions System starts up Changing the default satellite Monitoring the antenna status Setting sleep mode Entering setup mode Setting the satellite pair Editing satellite information Setting the antenna parameter Setting the LNB local frequency Setting GPS Setting the DiSEqC method Display versions Display power status Setting antenna go position Setting antenna move step Setting remote control Setting the factory default parameters Performing diagnostic tests WARNING Note Many of the above functions will only be required only after initial installation of your system Refer to the Quick Installation Guide before operating the system Operation Using the DACU 23 Operation Using the DACU DACU Soft Keys esl Antenne Contre Unit Press to select On screen option Press to select On screen option For Ka band antenna K4 K6 For Ku band antenna i4 i6 Normal Mode Start Up K4 K6 With the system installed and power applied the DACU screen will show the following sequence 1 Communication is being established between the SE Q antenna and the DACU The DACU initialized AN K6 HD O O O O 2 The antennais initialized TIALIZE ANTENNA NTELLIAN K6 HD O Li O 3 The antenna is searching for Satellite A SEARCH A DTV99 O B
31. ertagde Legd i pe Seen osm ie KREMO Wer 407 Tracking Satellite DTV 99 DTV103 Local Freq TEOSE Mis Signal Lewd bien Aetnmpa PE Losrpites Var 200 Sel Ameren GPS and Find Anenna Angle Zei Satelite bafon gea Zei Wrecking ieformation of Sallie Primary Set Trecking formation of Satelite Second Moye Jaton Execute Diagresls Zei dates Parenetions jee Cone Selal Communisten Chipley Paremeicis bot Engineer States Deep S earch Setup Tracking Wee GG Uer het denna r Tracking Satellite DTV 101 DTV110 DTV119 Beforom alles P4075 Ver doz Local Freg 11750 Mite Dier Level H Caen Besg sde WARNING The operation method is exactly same for both K4 K6 and i4 i6 The below instruction will be explained using the i4 i6 as example 54 K4 K6 Satellite Antenna System Install and User Manual Program Initialing and Serial Port Setup The communication between the ACU and antenna must be established as the first step in order to start setting your antenna freien Anma PE iota Ver 240 ee Baudrate setting Zei Antena GPS and Find Amenna Angle Zei Satelite information Communication status Sei Tracking iefarmaties al Satellite Primary j t Set Trecking iformatios of Satelite Secondary display Moye Aston Execute Disgeenle e Zei Antenna Parameters dae Cortal Seale Communication Driplay Parameters tot Engineer States Ss recking Seteilte Search
32. eswciccscevecsasscesscucescassencsdsacccascccsxeestte 15 CONNECTING THE SYSTEM TOA Ob 20 TARGET SATELLITE SETTING EE 21 OPERATION INSTRUCT ION ccccccssssscccccsscsccccccsscccccccccscccccccccccsooses 22 TINTRODUCTION ENEE 22 OPERATION USING THE DACH 00 ccscccccccssscsccccccscccccccccccccccccescccsceess 23 PACU SO T E EE 23 NORMAL M e RE 23 SET UW Te EE 28 OPERATION USING PC CONTROLLER PROGRAM cccssssseees 51 INTRODUCTION EE 51 INSTALLATION USB TO SERIAL DRIVER ccccccssccccssccccesssccescceesecccessesceesecss 52 PROGRAM INITIALING AND SERIAL PORT SAETUp 54 MAIN MENU USING DEFAULT TRISAT MODE w ccc cseccecccesccececsccenscceesses 55 SET SATELLITE INFORMATION s oesssensseensseersseossserssstrssessseeossresscrssecosseersserese 56 CONTROLER EE 59 TROUBLESHOOTING eege 64 PREPARATION FOR TRANSPORTATION cccccsssssscccccsscsccccccccscsccees 66 NVR CAIN EEN 67 APPENDIX K6 TECHNICAL SPECIFICATION csccccccssssssccccceees 68 APPENDIX K4 TECHNICAL SPECIFICATION scssscssseoscsessseeoees 69 Introduction 1 INTRODUCTION Introduction to Intellian K4 K6 Intellian K4 K6 is the world s first marine in motion satellite TV antenna system that is compatible with the Ka band broadcasts from DIRECTV s satellites called 99 W and 103 W the position related to Earth is expressed in longitude degrees These satellites
33. g the selected satellite e Initialize Antenna or the ACU is initializing e Unwrap Antenna is unwrapping the wire e Setup Antenna is in setup mode e Comm Antenna is possible communication Definition of Program Command Buttons Restart To exit setup mode and restart antenna again Setup To enter the setup mode Get Antenna Information To indicate the information on display after receiving it input to the antenna Factory Setting To initialize all antenna information to the default as same as ex factory status Load Default To show the up to date information input to PC program on display Update Default To update the antenna information by the up to date input to PC program 56 K4 K6 Satellite Antenna System Install and User Manual Set Satellite Information Ee m r lge jeiorg aban Taie E omgir Edhi Setetite bnleen tan Campen gt Dr tg gt iio E w e Satellite name and longitude Caban DTV SPR Satellite Verification method DS Decade elect Triple Satellite Ti keem gend tis Itegpsies Aer Sat Hie gsiee Vie gier Register satellite for tracking far Eat fl der Sat DiSEqC using method LesetTrequency Select LNB type Set local frequency of LNB Univeraal LA n Satellite Information The name longitude and confirmation method of the satellite is displayed when a satellite is selected in the list box Pus
34. h Edit Satellite Information button to update the information on modifying the value DiSEqC When the operation method of DiSEqC is selected to Change Band DiSEqC may be used for updating the local frequency and to Change Satellite for updating the target satellite Registration of target satellite In case that Tri sat Mode is selected and the DiSEqC is selected to Not Use only Register for Sat A Register for Sat B and Register for Sat C may be registered Pushing or or button after selecting the satellite in the list box makes it possible to register A or B or C Local Frequency In case that DiSEqC is selected to Change Band be sure to push the Universal LNB button In case that the DiSEqC is selected to Not Use or Change Satellite be sure to push Single Band button and key in into the Local Frequency and then push Set Local Frequency button Operation Using PC Contoller Program 57 Command Button Edit Satellite Information To modify the satellite information Register for Sat A To register a satellite to satellite A Register for Sat B To register a satellite to satellite B Register for Sat C To register a satellite to satellite C Not Use Do not use DiSEqC Change Band To use DiSEqC to change band Change Satellite To use DiSEqC to change the satellite Singe Band Antenna in use of Single LN
35. is applied when DiSEqC signal is detected from IRD After modifying information press Edit Satellite Information button then new information is updated in the antenna e Pol amp Band Control The power controls 13V Vertical RHCP and 18V Horizontal LHCP bands The Band controls High and Low bands AUTO RRECOMMEDED AUTO amp AUTO 13V and 18V supplied to LNB without regard to IRD AUTO amp OKHz Low band supplied to LNB without regard to IRD AUTO amp 22KHz High band supplied to LNB without regard to IRD 13V amp AUTO 13V supplied to LNB without regard to IRD 13V amp OKHz 13V amp Low band supplied to LNB without regard to IRD 13V amp 22KHz 13V amp High band supplied to LNB without regard to IRD Operation Using PC Contoller Program 61 18V amp AUTO 18V supplied to LNB without regard to IRD 18V amp OKHz 18V amp Low band supplied to LNB without regard to IRD 18V amp 22KHz 18V amp High band supplied to LNB without regard to IRD Set Tracking Information of Satellite Secondary Tracking ile mates jeratan Satellite to be edited Satellite Wim D VERTICAL j RHCP Satellite information for Vertical amp Low band Oe Freq 1PH M zoa His Satellite information for Horizontla amp Low band Satellite information for Horizontal amp High band Ega Sater kinm Hion DiSEqC using method Command Button Edit Satellite Information
36. ller Tracking Default update complete successfully DISEqC OFF Initialize Register Register Unwrap for Sat for Sat B Setup SleepMode Load Update Default Default Comm DiSEqC Local Freq m Operation Using PC Contoller Program 59 Controller menu Set Antenna GPS and Find Antenna Angle Antenna makes use of GPS information to search satellite quickly The more precise the GPS information is the quicker the antenna is able to search the satellite The method to input information into GPS is to push Set GPS button after keying in the latitude and longitude information on City GPS Pushing Add City button stores the GPS information By selecting the stored region in the list box the GPS information of such region is displayed The Intellian K4 K6 satellite TV antenna system utilizes GPS data to locate the satellite faster Se SH gt Position stored in Antenna Seis a gek GPS Message Satellite Longitude f ia I L x J Aramsgih 715 99 Ekel KT Calculated Angle Ekee FDE Basch Pied Aeoges A Titw Ante rir GAS City GPS data Command Buttons Load GPS Files Reads in various city information from the GPS files Add City Adds the name of city and its GPS information to GPS files Delete City Deletes the name of city and its GPS information from the GPS files Set GPS Inputs the indicated GPS information on display to antenna
37. ly by using DACU The antenna can be controlled manually by using DACU SETUP MODE O 1 Press YES to enter setup mode YES NO CH O O 1 Press YES to enter setup mode ETUP MODE 2 Press NEXT ten times to enter the antenna move step mode 2 Press NEXT nine times to enter the antenna go SET SAT PAIR SS position mode PREV YES NEXT O O 3 Press YES to move step ANT MOVE 3 Press YES to go position PREV YE ANT GO POSITION O PREV YES NEXT O O O PP AZ 4 4 4 Move the antennain the azimuth AZ axis CW Move the antenna clockwise CCW Move the antenna counter clockwise EL Go to elevation control screen 4 Input position value for azimuth AZ axis EL increases the value decreases the value Change the underscored digit using the buttons Press INPUT to accept the value and move to next digit Press BACK to move to previous digit Press ENTER to move to next screen 5 Input position value for elevation EL axis S SS EE d H KI increases the value decreases the value O Change the underscored digit using the buttons O 0 O Press INPUT to accept the value and move to next digit Press BACK to move to previous digit Press ENTER to move to next screen POSITION GG SS SS S O Press NO to return to the Antenna Go Position i SS O mode O O 7 Press EXIT to return to main setup mode AZ
38. na GPS and find Antenna Angle Satellite registration You can register the target satellite through the DACU or the PC program To register the target satellite the antenna system has to be in SET UP mode and the required information is Satellite name Satellite Longitude Method of Satellite Identification Frequency of each of the band Symbol Rate Network ID Power Change method For detailed instructions please refer to page 31 Edit Satellite Information page 56 Set Satellite Information and page 60 Set Tracking Information of Satellite Satellite Pair Selection You can select the Satellite Pair from the list through the DACU or the PC program You can easily select the target satellite from the satellite pair For detailed instructions please refer to page 29 Setting the Satellite pair page 56 Set Satellite Information Target Satellite Selection Choose the target satellite from the Satellite Pair When selecting through the DACU you have to press the left button to select the target satellite while the antenna system is in either Searching Mode or Tracking Mode When using the PC program you can select either satellite A or satellite B from Tracking Satellite at anytime 22 K4 K6 Satellite Antenna System Install and User Manual Operation Instruction Introduction This section of the handbook describes how to set up your Satellite TV System aft
39. ntenna you have to remove the radome and remove the shipping foam from the antenna interior Replace the radome before installation 12 K4 K6 Satellite Antenna System Install and User Manual Mark of the antenna mounting position Referring to the mounting template mark where antenna is to be mounted onboard the ship it must be a flat surface or on a separate power tower by drawing below E e KI ge 30 37cm 12 Ki J 30 37cm 12 Intellian K6 Installation 13 22 86cm 9 22 86cm 9 Intellian K4 WARNING If a power tower is not suit to mount the antenna separate cable shock and waterproofing measures must be taken to protect the RF connector from begin exposed to the sea water and external shocks An exposed cable may cause electric shock and cause serious damage to the equipment Securing hole for bolts and cable way Make 4 bolt holes of 10mm diameter one at each corner of a rectangle drawn as above and make a circular hole of 80mm diameter at the center of the rectangle through which the cable will run 280mm e Ke ra idm U ei 10mm Drill GER Pi 14 K4 K6 Satellite Antenna System Install and User Manual Connection of the RF cable Remove the rubber protector from RF connector Connect the RF cable to the RF connector under the base plate through the access hole using an 11mm spanner Be careful not to tighten it too much as you may damage th
40. o enter setup mode 2 Press NEXT seven times to enter the view power mode 3 Press YES to view power 4 ACU Voltage is shown Press center soft key to view antenna voltage Press EXIT to return to main setup mode 5 Antenna Voltage is shown Press center soft key to view IRD Voltage and frequency Press EXIT to return to main setup mode 6 IRD Voltage and frequency are shown Press EXIT to return to main setup mode 42 K4 K6 Satellite Antenna System Install and User Manual Setting Remote Control SET SAT PAIR PREV YES NEXT O O SETUP MODE O YES NO O O N SET REMOCON PREV YES NEXT O O FUNC CHANGE SAT NEXT SELECT EXI FUNC SLEEP MODE NEXT SELECT EXI PRESS A REMOTE KEY O BACK E O XIT O O O Press YES to enter setup mode Press NEXT eighttimes to enter remote control setting mode Press YES to set remote control Select the Function NEXT Shows nextfunction SELECT ENTER Registers a key on remote control Point remote control to ACU Press any key on remote control for selected function and press same key again for confirmation Press BACK to move to previous screen Press EXIT to return to main setup mode Operation Using the DACU 43 44 K4 K6 Satellite Antenna System Install and User Manual Setting Antenna Move Step Setting Antenna Go Position The antenna may be moved by 1 step manual
41. o the DACU s built in 8 receiver connectors NMEA 0183 GPS Interface A GPS Interface supports an external GPS which can provide the K4 K6 even higher performance Introduction Basic System Configuration For your satellite TV system to work properly the system will have to be connected with all of the provided components properly as shown in the figure below Refer to next chapter Installation in this manual for more detailed connection instructions Separate purchase of a satellite receiver and a TV is required K4 K6 DTV 99W 103W i4 i6 DTV 101W 110W 1119W Intellian m Intellian W us D OO Hi Power RF 1 RF2 RF2 RF1 Aoo an S fesoloclt Receiver 1 U U H H Receiver 4 ra a R oml EY 333 B omal e OR USB I F Cable B Band Converter RF Gable B Band Converter Receiver 2 Receiver 3 e E BS A Tee ij B Band Converter B Band Converter X Connectup to 8 Receivers Not Supplied B Band Converter and Receiver 4 K4 K6 Satellite Antenna System Install and User Manual Installation The components of the Intellian K4 K6 have been designed to be modular so that it is suitable for simple installation on all types of vessels S
42. omm Sepp Serial port setting Tracking batons a rom D Connect Disconnect E ri Button e z map iwiga isformalina Beta e Z eepMrde Lead lt Seming Cmm Bee begeint 351 Wer doz Local Freg 11750 Mite Command Button e Baud Rate Setting To display communication speed e Connection Status Display To display communication port between ACU and PC e Serial Port Setting To select serial port to be used es Connect Disconnect To establish communication between PC and ACU Operation Using PC Contoller Program 55 Main Menu Using Default Tri sat Mode intellian Antenna PC Controller Ver 3 03 Antenna GPS and Find Antenna Angle Set Satellite Information Set Tracking Information of Satellite Primary Set Tracking Information of Satellite Seconds Execute Diagnosis Controller Menu Antenna status monitoring Serial Communics tion Display Parameters for Engineer Select amp Monitor target satellite Triple sat as Default Mode DTV101 SATA DTV110 SAT B Tracking Setup Initial IRRE DTV119 SAT C Unwrap Get Antenna eeesgech Semp comer Ei Comm B2 603S Ver 4 02 Local pe 43958 se Local frequency a D Signal wS o gt Sig nal strength Communicate Smarter Connect Bootloader Antenna Status Monitoring e Search Antenna is searching for the selected satellite e Tracking Antenna is trackin
43. on e Go to Target Position To move the antenna to the present position e Diagnosis To diagnose the antenna BLUE Passed RED Failed GREEN Under diagnosis Operation Using PC Contoller Program 63 Set Antenna Parameters for Control Product Information arameter Setting Tracking Level Dffpei a0 WEE Debet Parameter Setting Eat on Threghohf Lo ds Parameter Setting bewei Oire Cuba Adjucet Set Contral Parameters Parameters Parameter Setting Zrnagch Lock Cound Ditet Oia AH LH Set Plaga Gei Ur Qant Dllesencr Command Buttons Set Control Parameter To register parameters values Set Flags To set flag setting for WRS Method or Offset Difference Product Information Antenna dish size Serial NO Voltage for antenna and ACU Software version for ACU and Control Parameter Setting To set antenna parameter values SCAN OFFSET The actual angle between the marked point on sub reflector and the datum TRACK SCALE To control the tracking speed while antenna is tracking the satellite High track scale value resulting in high tracking speed DETECT LEVEL The basic single detection level TRACKING LEVEL The basic signal tracking level ELADJUST The mechanical tolerance compensation of elevation limit WRS LEVEL The basic WRS detect ion level VOLTAGE THRESHOLD The value to identify Vertical Horiz
44. ontal or RHCP LHCP DISEQC THRESHOLD The value to identify 22KHz tone OFFSET DIFFERENCE The difference value between RHCP LHCP and SCAN OFFSET USE WRS To apply WRS while antenna is searching for satellite USE OFFSET DIFFERENCE To apply Offset Difference 64 K4 K6 Satellite Antenna System Install and User Manual Troubleshooting Possible cause Symptom No picture on TV set System will not find satellite Snowy television picture Intermittent picture for short intervals System works at the dock but not underway Note for an explanation of possible cause and their remedies refer to the following paragraphs 1 Blown fuse low power or wiring Check that the in line quick blow fuse if fitted has not blown or the circuit breaker has not tripped Replace fuse with one of the same type and rating If you have extended the power cable from the antenna unit check that there is no power loss Check the system wiring and connections 2 Satellite signal blocked Satellite signals can be blocked or degraded by buildings other boats or equipment on your boat Check to see if the antenna has a clear view of the sky 3 Outside satellite coverage zone Your system will provide excellent reception within the antenna coverage area for your satellite television service However signal quality may degrade as you approach the edges of this zone 4 Radar interference The energy levels radiated by ra
45. ove or below the level of the radar Make sure that the mounting surface is rigid so that it will not flex when the vessel vibrates If necessary add a stiffening member to the mounting site to strengthen it The movement of the antenna can be minimized by installing it at the center of the ship For optimal performance of the antenna it is not recommended to install at any corner of the ship where the movement of the ship is the greatest Install the bottom of the antenna parallel to the surface of the sea and fix tightly to the structure of the ship When setting the antenna down be careful not to have the RF connector Striking the connector on the bottom directly will damage the connector and make connection impossible Installation 9 Cables Before installing the system cables you need to take the following points into consideration e All cables need to be well clamped and protected from physical d amage and exposure to heat and humility e Cable with an acute bend is not allowed e Where a cable passes through an exposed bulkhead or deck head a watertight gland or swan neck tube should be used Power requirements You need to follow the power requirements to avoid damage the system Intellian K4 K6 has been designed to work on a boats power supply rated from 90 260V AC If your IRD s and television s require a 110V 240V AC power supply you will need to install a suitable DC to AC converter to ope
46. ove to nextscreen MIM 1 234567 8 PREV ON OFF NEXT O O O 5 Press YES to save selections Press NO to cancel and return to main setup mode Operation Using the DACU 47 Executing Antenna Diagnosis It is possible to see the antenna status by reviewing the result of diagnosis of the antenna Refer to the following codes to understand the diagnosis results 1 Press YES to enter setup mode ETUP MODE 2 Press NEXT twelve times to enter Antenna Diagnosis mode 3 Press YES to diagnosis antenna 4 CODE 101 is being tested Press EXIT to return to main setup mode 5 CODE 101 has passed CODE 101 PASSE Press EXIT to return to main setup mode RESULT 48 CODE 101 CODE 102 CODE 103 CODE 104 CODE 105 CODE 106 CODE 107 CODE 108 CODE 109 CODE 110 K4 K6 Satellite Antenna System Install and User Manual Communication between antenna and antenna control unit is tested If failed check the power and data cable AZ CW limitis tested If failed check the limitsensors motor and belt for AZ axis AZ CCW limitis tested If failed check the limitsensors motor and belt for AZ axis EL axis is tested If failed check the limitsensors motor and belt for EL axis Sub reflector is tested If failed check the sub reflector L
47. rate the unit s from your boat s DC power supply Extending the Cables The cables that have been supplied with your Intellian system should be of adequate length to complete the installation on most boats Antenna DACU RF and DACU Power Cable This cable is supplied at a length of 15m If a longer length is required you should replace this cable with an extended RF cable supplied by Intellian Technologies WARNING Exceeding the indicted cable lengths will result in reduced performance of your system 10 K4 K6 Satellite Antenna System Install and User Manual Installation and Mounting of antenna The method of installation and mounting of antenna may vary with vessel design but the following procedures are applicable in most situations and will result in a secure and effective installation Confirmation of size prior to installation Confirm the height and diameter of the bottom surface of the antenna before installing it The space must be sufficient for installing the antenna unit considering the height and diameter of the antenna The height and the diameter of the bottom surface of the antenna are as shown in the following drawing If possible install the antenna using a power tower 72cm 28 3 Intellian m 70cm 27 5 Intellian K6 Installation 11 54cm 21 2 Intellian m 50cm 19 7 Intellian K4 WARNING Before installing the a
48. ss YES to accept the selection 1 DiSEqC method DO NOT USE DISEQC DiSEqC is notin using USE TO CHANGE BAND DiSEqC is used to change to low and high band USE TO CHANGE SAT DiSEqC is used to change tracking satellite Press NO to cancel and retum to main setup mode 40 K4 K6 Satellite Antenna System Install and User Manual Display Versions This sequence enables you to see what version of antenna and DACU software version are installed on your system 1 Press YES to enter setup mode ETUP MODE 2 Press NEXT six times to enter the view version mode 3 Press YES to view version SF 6018 4 Antenna productname and S N are shown S N 0000000000 E Press center soft key to view antenna software version Press EXIT to return to main setup mode O o ANT S W VER 5 Antenna software version and S N are shown S N 00000000 00 F Press center soft key to view ACU software version Press EXIT to return to main setup mode ACU S W VER Ge als ere and S N ra S S N 0000000000 E ress to return to main setup mode Operation Using the DACU Display Power SETUP MODE O YES NO O A O O SET SAT PAIR PREV YES NEXT O IEW POWER YES NEXT O HA S EXIT e QO O ANT POWER 25 9 V O E O XIT O QO O eae QO RD EXIT O QO O 41 1 Press YES t
49. ue and move to next digit Press BACK to move to previous digit Press ENTER to move to next screen 6 Press YES to accept the data O O O Press NO to cancel and retum to main setup mode Operation Using the DACU 37 CASE 2 Universal LNB is used Low band local frequency 9750 MHz High bnad local frequcny 10600 MHz ETUP MODE ET SAT PAIR e ES E SE T LOCAL FRE C E EV YES 1 LNB Type SINGLE Single Band LNB Asia 11300 MHz Japan 10678MHz Korea 10750MHz America 11250MHz DirecTV Ka band LNB 18050 MHz UNIVERSAL Universal LNB Low band local frequency 9750 MHz High band local frequency 10600 MHz Press YES to enter setup mode Press NEXT four times to enter set local frequency mode Press YES to set local frequency Select the LNB Type UNIVERSAL PREV Shows previous LNB type SELECT Set the displayed LNB type NEXT Shows next LNB type Press ENTER to move to next screen Press YES to accept the data Press NO to cancel and retum to main setup mode 38 K4 K6 Satellite Antenna System Install and User Manual Setting the GPS It is possible to set up and modify the GPS information which enhances the antenna functionality SETUP MODE O YES NO O H O Q SET SAT PATR S O 2 Press NEXT to enter GPS setup mode PREV YES NEXT Q QO O ar
50. ystem Components Antenna Unit The antenna of Intellian K4 K6 is composed with the following components for the optimum search and reception of the satellite signal Mechanical Unit manipulates the antenna to receive the optimal satellite signal regardless of the movement of the vessel Dual Antenna Control Unit controls mechanical operation of the K4 K6 and i4 i6 at same time RF Unit transmits the optimum satellite signal to the receiver Radome protects the antenna from the severe marine environment Intellian m Installation 5 Dual Antenna Control Unit DACU The Dual Antenna Control Unit DACU provides the power to the antenna and controls the various settings of the dual antenna simultaneously Additionally VFD Vacuum Fluorescent Display allows for you to operate the DACU in the dark The functions of the DACU are as follows Control dual antenna systems at one time Connect up to 8 receivers directly Provide power for the antenna unit Monitor the antenna status Change the target satellite Set up the user environment Set up the receiver to be a Master receiver Set the current GPS information Set satellite information Move antenna manually Perform self diagnosis of the antenna Set up the interface witha PC Baal Anions Centre ret Front Rear K4 K6 Satellite Antenna System Install and User Manual Installation Kit Contain the items requir
Download Pdf Manuals
Related Search