Installation Manual
Contents
1. wall 1 3 16 30mm 2 3 4 70mm 2 3 4 70mm 3 1 8 80mm Recommended mounting bracket heights from floor are as follow Male Female 29 1 2 750 mm Children 23 1 2 598 mm Handicapped 21 1 2 547 mm To be continued on the back Bes EEE Complete the electrical wiring Place chassis assembly onto the bottom bracket Using wire nuts connect power cable from hand dryer to power supply in the junction box confirm with certified electrician on correct wire nuts to use Place connection point with wire nuts into the junction box Hang chassis assembly onto the top bracket Junction box Actual Placement Connection point Bracket Bottom Chassis Assy Place mounting platform Junction box Actual Placement Place connection point with wire nuts into the junction box Connection Diagram Connect the cord firmly with a wire nut or equivalent onto mounting bracket hooks Mount the Chassis Assembly and Drain Tray Assembly Make sure all electrical wiring is placed away inside the junction box Use 2 screws M4 that come with the product and tighten unit to the bottom bracket Junction box Actual Placement Screw in two screws onto bottom of body through the bottom bracket Chassis Assembly Drain tray ON Attach water tray after installation is complete Function Tes2. Rating 120V AC 4 25 Amps 60 Hz 510 W Do not install the unit in the places where corrosive or combustible gas can be present Power Connection Hardwiring This may cause product failure or damage Power Saving Function Automatically turns OFF after 60 seconds of use Decibel Rating 58 dB Air Speed 224 mph 100 meters second Dry Time 12 seconds Drain Tray Capacity 0 27 gal 950 ml Ambient temperature 32 104 F 0 40 C Size 9 5 8 x 18 1 2 x 6 5 16 Weight 22 2 lbs 10kg Never attempt to disassemble for repair or modification This may cause electric shock fire injury or failure disassemble y Jury Do not install outdoors or where it is exposed to water Do not use in This may cause current leakage electric shock fire or failure humid area OGU3049E 2009 04 Before Installing 1 Precautions 3 9 16 90mm 2 3 8 60mm 2 3 8 60mm 5 1 8 Confirm the rough in major dimensions and wiring diagram before installation in order to properly install the hand dryer and electrical wiring 11 13 16 1 1 ane 300mm All electrical wiring should be installed in accordance with national local codes and regulations with assistance from a certified electrician i L lt ga FINISHED gt y WALL Mounting surface should be even and smooth Confirmation must be made that the wall has enough strength for hand dryer installation and be sure to use all the
3. TOTO INSTALLATION MANUAL Clean Dry High Speed Concealed Hand Dryer Warranty Registration and Inquiry For product warranty registration TOTO U S A Inc recommends online Warranty Registration Please visit our web site http www totousa com If you have questions regarding warranty policy or coverage please contact TOTO U S A Inc Customer Service Department 1155 Southern Road Morrow GA 30260 888 295 8134 or 678 466 1300 when calling from outside of U S A Important Safeguards For your safety please follow the instructions below A Warning db It is necessary to install a circuit breaker in the power supply Failure to do this may cause electric shock during overload or short In this Instruction Manual the following symbols are shown for safe and proper use of Important i uit the product and to alert you of the possibility of personal injury and damage to your property The symbols and their meanings are as follows Caution GD The chassis assembly must be installed on a smooth and even important wall surface which has enough strength Failure to do this may cause damage or personal injury if it falls down Ignoring these symbols may cause personal injury and or property damage Warning Ignoring these symbols may cause severe injury and or property damage Caution i Specification Some models may have different components from the ones illustrated below Product HDR110 SS Power
4. cket Bottom w o Top Cover Junction box Connection type Air nozzles A Wall surface lt Bottom view gt Filter case lt View with cover removed gt X Model is subject to change without further notification Using template provided mark the wall for locations and install the mounting bracket 3 9 16 90mm Wall thickness needs to be 5 to 30mm 4 7 2 3 8 60mm 2 3 8 60mm Beam Stud lt S Finished iwall Junction box location 2 50mm 30mm Wall thickness needs to be 5 to 30mm A Bottom Drain tray Remove drain tray Finished Wall during installation x Beam Stud Wall 1 9 16 40mm Complete the electrical wiring install the junction box and connect the power cord using wire nuts Mount the chassis assembly and drain tray assembly Install the top cover and drain tray Mark the wall with template and install the bracket __ Chassis Assy must be installed on a rigid and even surface Caution Failure to do this may cause damage or personal injury when it falls Attach the bracket firmly on the rigid wall with the three screws 94 530 provided In the case of a tile or concrete wall please use plastic plug anchors with screws provided 3 9 16 90mm 2 3 8 60mm 2 3 8 60mm es eG cl Finished
5. mounting hardware provided to securely install the hand dryer Junction box location 26 5 16 668mm It is necessary to install circuit breaker for the power supply 2 50mm E A 7 i lt a he 3 16 30mm 2 3 4 70mm 2 3 4 70mm 3 1 8 80mm 2 Others Pay special attention so that both the top cover and the sensor surface are not flawed or scratched Do not place other devices using inverter or infrared sensor near the hand dryer this may cause malfunction Recommended mounting bracket heights from floor are as follow Male Female 29 1 2 750 mm Children 23 1 2 598 mm Handicapped 21 1 2 547 mm Meets the American Disabilities Act Guidelines ANSI A117 1 and CSA B651 requirements when mounted in a recessed wall where the front surface is not more than 4 102mm from finished wall and max height of air blower outlet from finished floor is 47 1 4 1200mm OPEN WALL 27 9 16 27 5 8 700 2 mm 12 5 8 5 1 8 320mm 130mm l n stal lati O n Some models may have different component as illustrated below Hand Dryer Unit Top cover Color White Black Green Size AWG16x3 5 Power Cable L Wiring Hole Chassis Assy Filter Water Tray Filter case Drain tray Accessories M4x6 x2 Bracket Top Fos S Installation ositior P K gt 9 4 5x30 x6 5 Bra
6. t 1 Checking after installation Wiring Diagram E Test the product as follows after the installation is complete Sensor First peel off the seal on the filter F The seal is used to protect the filter from scratches during E i shipment it is no longer needed _ Air nozzles Lz SS Peel off the seal ie Control Assembly Power Connector Power Fuse 1 Check the circuit breaker o PE gt gt Turn the circuit breaker ON ZH W 2 Check the functionality G Place your hand under the outlet nozzles to see if air blows out Body Case G B BLACK R RED W WHITE After you check the functionality by trial run give the user manual Bu BLUE with warranty to the customer and explain how to use and maintain the G GREEN product WE After trial run
Download Pdf Manuals
Related Search