Home

User Manual - Howard Computers

1. Both On Timer and Off Timer have been set but different time is showing Apply current time to synchronize the display clocks The remote may not function properly when you turn off the remote Function disconnect the RS 232C cable or exit the program in an Irregular manner Rerun the program and turn the remote function again to Restore normal functions lt Note gt This program may malfunction due to problems in communication circuits or interference from electronic appliances nearby Please make selection in the information grid before controlling Settings Value Display In Multiple Display Mode Ye When there are more than one displays connected the settings values are displayed as follows i 2 3 No selection Displays the Factory Default Value Selected one display Fetches and displays the settings value for the selected display Selected one display ID1 and add another display ID3 The program which was displaying the settings value of ID 1 fetches and displays the value of ID3 If all sets are selected at the same time by clicking All and Select the default value will be restored Copyright c 2003 2011 Samsung Electronics Co Ltd All rights reserved Adjusting the PDP Display Input Available Modes i PC DVI BNC e Elav HDMI 4 Component Source List Use to select PC DVI or other external input sources connected to the PDP Display Use to select the screen of your
2. e This device may not cause harmful interference and e This device must accept any interference received including interference that may cause undesir able operation ote Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment PowerSaver This PDP Display has a built in power management system called PowerSaver This system saves by switching your PDP Display to low power mode when it has not been used for a certain amount of time The PDP Display automatically returns to normal operation when you press a key on the key board For energy conservation turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPM compliant video card installed in your computer Use the software utility installed on your computer to set up this feature PowerSaver State Normal Opera Power saving Power off tion mode Power Indicator On Blinking Off Power Consumption 550 watts 2 watts 0 watt Typical Note e The actual power consumption may be different from the indicated power consumption if the system condition or settings are changed e To stop any power consumption disconnect the power cable on the back Be sure to disconnect the power if you intend to stay away from home for many hours Specifications Preset Timing Modes If the signal transferred from the comp
3. source etc With cables or signal source where there is no degradation up to 10 PDP Displays can be connected May not be supported depend ing on the connected cable an C COMPONENT IN R Pp G Y B P5 H V BNC Component Connection Terminal in put During BNC input please check specifications for the input ports below R Pp gt Red port input G Y gt Green port input e B Pp gt Blue port input During component input please check specifi cations for the input ports below e R Y gt Green port input e G P x gt Blue port input B Pp gt Red port input This product has an internal speaker Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the PDP Display causing a malfunction due to interference with the frequency pm o Na 10 11 Po SAMSUNG 1 POWER 2 CJ OFF 3 Number Buttons 4 DEL GUIDE button 5 VOL 6 SOURCE 7 U D MENU 21 Introduction POWER QOorr Number Buttons DEL GUIDE button VOL SOURCE D MENU TOOLS Up Down Left Right buttons 1 INFO COLOR BUTTONS ELA TTx MIx MTS DUAL ENTER PRE CH tk MUTE Y CHP A TV MENU O RETURN exit MagicInfo B6 900000 90 O 896090990090 oo Turns the product On Turns the product Off Used to enter
4. Fie Remote Control Safety Lock Pow ver t Control Port Selection Lamp Control Options Select a CS ID ingat 7 o 4 5 m E fe things lt nd Maint nance E OSs om el os oi a a fam ng Uae Ol el e PC Mode 1 E Multiple Display Control Fie Remote Control Safety Lock Por Selachon Lamp Control Options Sala ct Cle ar C O Power Control Maintenance Help Help Refresh Choose Input Source PC O NN 6 BR S Video Componen DTV Channel Refi sh Choose Input Source Peo AV S Video Component B HDMI HDMI Info Grid shows some basic information necessary to Input Source Control PC Changes the Input Source of the selected display to PC 2 BNC Changes the Input Source of the selected display to BNC 3 DVI Changes the Input Source of the selected display to DVI 4 TV Changes the Input Source of the selected display to TV 5 DIV Changes the Input Source of the selected display to DTV 6 AV Changes the Input Source of the selected display to AV 7 S Video Changes the Input Source of the selected display to S Video 8 Component Changes the Input Source of the selected display to Component 9 MagicInfo The Input source of MagicInfo works only on MagicInfo model 10 HDMI1 HDMI2 Changes the Input Source of the selected display to HDMI 11 DP Switches the input
5. MDC S ystem Introduction RS 232C OUT RS 232C In RS 232C In ol oA le RS 232C Out RS 232C Out RS 232C Out A Multiple Display Control MDC is an application allowing various displays to be easily and simultaneously operated on a PC RS 232C a standard of serial communication is used for the communication between a PC and a display Therefore a serial cable should be connected between the serial port on a PC and the serial port on a display Main Screen Click Start gt Program gt Samsung gt MDC System to start the program Select a set to see the volume of the selected set within the slider a a ee CO 10 11 12 13 Poot On Power Off Volume 10 ii circrcerer af O5D Display Source OSD On Not Optimum Mode OSD On No Signal OSD On Nil o MDCOSD n Main Icons O All E3 Remote control O Selection Buttons Safety Lock 10 Refresh O Port Selection D Display Selection O Lamp Control 12 Info Grid O Option 13 Control Tools 7 Dropdown Selectors 14 OSD Display Use the main icons to switch into each screen Allows you to enable or disable the remote control signal receiving function of the display unit Set the Safety Lock function When setting the Lock function you can only operate power and lock buttons on the remote control and set The setting for the PC Serial Port can change The original value is COM1 Selects a
6. O DVI IN PC Video Connection Terminal Connect the DVI IN port on the monitor to the DVI port on the PC using the DVI cable i NT DVL RGB pa Pining AUDIO IN 100 8 Introduction O DVI RGB AUDIO IN PC DVI Audio Con nection Terminal Input Connect an audio cable to R AUDIO L on the monitor and the audio out port on the source de vice O V COMPONENT AUDIO IN R AUDIO L Connect an audio cable to R AUDIO L on the monitor and the audio out port on the source de vice O pr OUT e Connecta monitor to another monitor through a DVI cable e Connect the DVI OUT port on the monitor to the HDMI IN port on the other monitor using the DVI to HDMI cable DVI HDMI and network signals sent via the DVI OUT port are displayed on the second display which has the DVI IN port AV IN VIDEO Connect the AV IN VIDEO terminal of your monitor to the video output terminal of the exter nal device using a VIDEO cable uupro OUT Headphone External speaker output terminal HDMI IN Connect the HDMI terminal at the back of your PDP Display to the HDMI terminal of your digital output device using a HDMI cable Up to HDMI cable 1 2 can be supported Introduction BNC OUT R G B H V BNC Terminal Output BNC Analog PC Connection connecting the R G B H V ports The number of PDP Displays that can be connec DO ted to the loopout depends on the cables signal pO
7. The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance Safety Instructions Notational Power Note These safety instructions must be followed to ensure your safety and prevent property damage Make sure to read the instructions carefully and use the product in the correct manner o Warning Caution OD Note SQ Prohibited 4b Q Do not disassemble Q Do not touch 5 Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment Important to read and under stand at all times Disconnect the plug from the outlet Ground to prevent an electric shock An administration fee may be charged if either e a an engineer is called out at your request and there is no defect in the product i e where you have failed to read this user manual b you bring the unit to a repair centre and there is no defect in the product i e where you have failed to read this user manual The amount of such administration charge will be advised to you before any work or home visit 1s carried out A When not used for extended period of time set your computer to DPM If using a screen saver set it to active screen mode The images here are for reference only and are not applicable in all cases or countries Shortcut to Anti Afterimage Instructions L Do not
8. 4b Adjust Return Color temp is a measure of the warmth of the image colors Note This function is only enabled if the Color Tone is set to Off Size Move Enter Return The Size can be switched 1 16 9 Sets the picture to 16 9 wide mode Adjusting the PDP Display 2 Zoom 1 Magnifies the size of the picture on the screen 3 Zoom 2 Magnifies the size of the picture more than Zoom 1 4 4 3 Sets the picture to 4 3 normal mode 5 Just Scan Displays the input scenes as they are without any cutoff when HDMI Compo nent 720p 10801 1080p signals are input Note e Certain external devices may feed the display an out of spec signal that may cause cutoff even when using the Screen Fit feature e Zoomi and Zoom are not available in HDMI or Component mode e The Position and Reset functions are available in Zoom 1 or Zoom 2 modes Digital NR Digital Noise Reduction Turns the Digital Noise Reduction feature Off On The Digital Noise Reduction feature allows you to enjoy clearer and crisper images Deactivated in HDMI AV with a resolution of 1080p 1 Off 2 On Note Digital NR function 1s not available for all resolutions Film Mode The Film Mode feature offers you a theater quality viewing experience Film Mode is supported in AV Component 4801 10801 and HDMI 4801 10801 Adjusting the PDP Display Note e In HDMI mode this function can be available when
9. r BN KA Wall Bracket 1 Hinge Left 1 Right Plastic 1 Hanger 4 Screw WUD 11 Screw B Anchor Introduction To mount the product on the wall bracket The shape of the product may vary depending on the model The assemblies of the plastic hanger and the screw are the same 1 Remove the 4 screws on the back of the product 2 Insert the screw B into the plastic hanger AN Notice e Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers e Be careful when installing the product on the bracket as fingers can be caught in the holes e Make sure the wall bracket is securely fixed to the wall or the product may not stay in place after installation 3 Tighten the 4 screws in step 2 plastic hanger screw B to the rear holes of the product 4 Remove safety pin 3 and insert the 4 product holders into the corresponding bracket holes 1 Then place the product 2 so that it is firmly fixed to the bracket Make sure to re insert and tighten the safety pin 3 to securely hold the product to the bracket Introduction A PDP Display B Wall Bracket C Wall Wall Bracket Angle Adjustment Adjust the bracket angle to 2 before installing it on the wall 90 5 0 z220 a m 1 Fix the product to the wall bracket 2 Hold the product at the top in the center and pull it forward direction of the arrow to adjust the ang
10. 7864 http www samsung com COLOMBIA 01 8000112112 http www samsung com COSTA RICA 0 800 507 7267 http www samsung com DOMINICA 1 800 751 2676 http www samsung com ECUADOR 1 800 10 7267 http www samsung com EL SALVADOR 800 6225 http www samsung com GUATEMALA 1 800 299 0013 http www samsung com HONDURAS 800 27919267 http www samsung com JAMAICA 1 800 234 7267 http www samsung com NICARAGUA 00 1800 5077267 http www samsung com PANAMA 800 7267 http www samsung com PERU 0 800 777 08 http www samsung com PUERTO RICO 1 800 682 3180 http www samsung com TRINIDAD amp TO 1 800 SAMSUNG 726 7864 http www samsung com BAGO VENEZUELA 0 800 100 5303 http www samsung com Europe ALBANIA 42275733 AUSTRIA 0810 SAMSUNG 7267864 http www samsung com 0 07 min BELGIUM 02 201 24 18 http www samsung com be Dutch http www samsung com be_fr French BOSNIA 05 133 1999 BULGARIA 07001 33 11 http www samsung com CROATIA 062 SAMSUNG 062 726 7864 http www samsung com Appendix Europe CZECH 800 SAMSUNG 800 726786 http www samsung com Samsung Zrt esk organizacni slo ka Oasis Florenc Sokolovskasg4 17 180 00 Praha 8 DENMARK 70 70 19 70 http www samsung com FINLAND 030 6227 515 http www samsung com FRANCE 01 48 63 00 00 http www samsung com GERMANY 01805 SAMSUNG 726 7864 http www samsung com 0 14 Min GREECE 2106293100 http www samsung com HU
11. ID corresponds to the transmitter setting becomes activated Troubleshooting Self Test Feature Check A note Check the following items yourself before calling for assistance Contact a Service Center for problems that you cannot solve by yourself Self Test Feature Check 1 Turn off both your computer and the PDP Display 2 Unplug the video cable from the back of the computer 3 Turn on the PDP Display The figure shown below Check Signal Cable appears on a black background when the PDP Display is working normally even though no video signal is detected While in the Self Test mode the LED power indicator remains green and the figure moves around on the screen Samsunga Check Signal Cable PC 4 Turn off your PDP Display and reconnect the video cable then turn on both your computer and the PDP Display If your PDP Display screen remains blank after using the previous procedure check your video con troller and computer system your PDP Display is functioning properly Warning Messages You can even view the screen at a resolution of 1920 x 1080 However you will receive the following message for a minute You can choose to change the screen resolution or stay in the current mode during that time And 1f the resolution is more than 85Hz you will see the black screen because the PDP Display does not support over 85Hz Not Optimum Mode Recommended Mode 1920 x1080 60Hz Note Refer to Specifications gt
12. Lamp adjustment mode Adjusts the number of LFD IDs and the frequency of search repeats Defines the range of LFD IDs to display You can select or deselect the displayed IDs using the Select or Clear button All of the monitors can be selected or deselected Selects Select or deselects Clear LFD IDs displayed by configuring 7 and 8 This searches for monitors The maximum number is indicated in the Max LFD Id field Select a display from Display Selection Use Grid to view brief information on selected display Use Control Tools to control displays 14 Switches the OSD function On Off May not be supported depending on the product lt Note gt The remote control Enable Disable function operates whether or not the power is On Off and this applies to all displays connected to the MDC However regardless of the status at the time the MDC is shut down the remote control signal receiving function of all displays is initialized to Enable when the MDC is closed Port Selection Multiple Display Control Port Selection Lamp Control Options Refresh Power Un Power Off Volume 10 O pan 4 Po 18 tan Tere Suha eRe OSD Display F ng o o ELE L Source OSD Not Optimum Mode OSD Ho Signal OSD MDC OSD 1 The Multiple Display Control is originally set to COM1 2 If any port other than COM1 is used COM1 through COM4 can be selected in the Port Selection Menu 3 If the exact port
13. T um ERR Error code that shows what occurred error is PIP ON OFF Control e Function The PC turns the PIP function of a TV or Monitor ON OFF This does not operate in MagicInfo mode e Get the PIP ON OFF Status ID CheckSum Ko e Set the PIP ON OFF Header command DATA DATA ID Length CheckSum OAA 0x3C PIP The PIP ON OFF code to set for the TV or Monitor 1 PIP ON 0 PIP OFF e Ack DATA Pina um Introduction PIP Same as above e Nak DATA paa um ERR Error code that shows what occurred error is e Auto Adjustment Control PC BNC Only e Function Personal Computer controls PC system screen automatically e Get Auto Adjustment Status None e Set Auto Adjustment Header command DATA DATA CheckSum ie Adjust ment Auto Adjustment 0x00 Always Header command DATA Ack Nak r CMD Vall Length Check Sum f3 fw esp pane justment DATA a Sam um lll ERR Error code that shows what occurred error is e Video Wall Mode Control e Function Personal Computer converts Video Wall Mode of TV Monitor when Video Wall 1s ON Only works with TV Monitor where Video Wall is on Introduction Does not operate in MagicInfo e Get Video Wall Mode ID CheckSum Ko e Set Video Wall Mode Header command DATA DATA Length ID CheckSum OxAA 0x5C 1 Video Wall Mode Video Wall Mode Video Wall Mode code to be set o
14. To use a stylus pen press the black button at the upper part of the pen Connections 3 3 Pairing Stylus Pens with the Monitor To connect dual pens to the monitor install the drawing program in the provided CD on the PC Refer to Installing Whiteboard for details about how to install the drawing program e Go to Control Panel and run Samsung Interactive Whiteboard Alternatively click the star icon Hiiil gt Pen Setting in the bottom left corner of the drawing program e Press and hold the black power button on the stylus pen for 10 seconds when the power button is turned off e Powering on the pen Press the black power button once The red LED will blink several times and the pen will power on e Powering off the pen Press and hold the black power button for 3 seconds The red LED will blink several times and the pen will power off e Press Pairing in the Samsung Interactive Whiteboard program If No Pairing changes to Conneted a pairing has been successfully performed and taps of the pen on the screen will im mediately be recognized Coaneclicn Pan Ho Fairing Yo Paring e Pairing is required only once After a pen is paired with the monitor powering on the pen will enable taps of the pen on the screen to be recognized 3 4 Activating Calibration e Go to Control Panel and run Samsung Interactive Whiteboard Alternatively click the star icon Ji gt Pen Setting in the bottom left corner
15. Turns on off the Mute function of the selected display When selecting one set at a time turn on the Mute function for the selected set The Mute function is disabled automatically when you adjust the volume level The values return to the default settings when you undo the selections or choose Select All amp The Power Control feature is available for all displays amp The Volume Control and Mute features are available only for the displays whose power status is ON 3 Selects whether to display the menu screen using the OSD Display menu Multiple in pila Lontroat File Remote Control Salety Lock Pon Selection Lamp Control Options Refresh Po wel Da a Power Of Volume 10 i sj OSD Display IC Ole pk PI S map d Era Aii o a j Source OSD 1 Source OSD Sets whether the Source OSD will be displayed to indicate when the Source is changed 2 Not Optimum Mode OSD Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported 3 No Signal OSD Sets whether the No Signal OSD will be displayed to indicate when there is no signal 4 MDC OSD Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC Soe Input Source 1 Click Input Source of the main icons and the Input Source control screen appears Selects displays you want to adjust using the Select button or checkboxes e TV Mode Multiple Dis apay Li oniro
16. including internal television speakers It is fully compatible with all multichannel formats Adjusting the PDP Display 1 Off Setup Available Modes J PC DVI BNC Eav HDMI 4 Component Language Li 4 English a WU Deutsch You can choose one of 13 languages English Deutsch Espa ol Francais ltaliano Svenska PyccKMn Portugu s Turkge JHE i ihi AAG 820 Note The language chosen affects only the language of the OSD It has no effect on any software running on the computer Time C7 8 You can set the time Clock Set Month Day Year it Hour Minute AMP MI O Retum Current Time Setting Adjusting the PDP Display Sleep Timer 150 180 Move Enter O Return Turns the PDP Display off automatically at certain times 1 Off 2 30 3 60 4 90 5 120 6 150 7 180 Timer1 Timer2 Timer3 pa On Time EM Inactivated Off Time 2 inactivated Volume Source Holiday C10 L PC Don t apph You can set the PDP display to automatically turn on or off at a specified time Note e Only enabled when the clock is set using the Clock Set menu e The Manual option allows you to select a day of the week e Holiday When Choose Apply timer is not available on holiday when choose Don t apply timer is available on holiday Holiday Management e Add Month Day Month Day ES Se o 2 Adjusting the PDP Display Y
17. name that is connected to the PDP Display using a serial cable is not selected communication will be unavailable 4 The selected port is stored in the program and used for the next program as well Power Control 1 Click Power Control of the main icons and the Power Control screen appears WA Multiple Display Control File Remote Control Safety Lock Por Selecton Lamp Control Options Help Refresh Power On Power Off Volume 10 ae OSD Display Source OSD Not Optimum Mode OSD No Signal OSD MDC OSD Ye Info Grid shows some basic information necessary to Power Control 1 E Power Status 2 Input 3 Image Size 4 On Timer 5 Off Timer 2 Selects displays you want to adjust using the Select button or checkboxes Mulhole Display Control Remote Control Safety Lock Pont Selecion Lamp Control Options Help Refresh Power On Powar OH F mg 4 Wolume iD A Saad a ee TO OSD Display Source OSD On Not Optimum Mode OSD On No Signal OSD On MDC OSD On Je WI Power Control allows controlling some of the functions of the selected display 1 Power On Off Turns the power of the selected display On Off 2 Volume Controls the volume level of the selected display It receives the volume value of the selected display from the sets and displays it in the slider If you deselect a single display or all displays the default value 10 will be restored 3 Mute On Off
18. of your TV by configuring the HDMI Black Level 1 Normal 2 Low Video Wall J TY A Video Wall is a set of video screens connected together so that each screen shows a part of the whole picture or where the same picture is repeated on each screen When the Video Wall is on you can adjust the Video Wall screen setting Note When Video Wall is running the Auto Adjustment Image Lock and Size functions are not available Video Wall does not operate in MagicInfo mode Video Wall Turns Off On the Video Wall function of the selected display Off On 1 Off 2 On Format E Natural Adjusting the PDP Display The Format can be selected to see a divided screen 1l Full Provides a full screen without any margins 2 Natural Displays a natural image with the original aspect ratio intact Horizontal Move Enter O Return Sets how many parts the screen should be divided horizontally Five adjustment levels 1 2 3 4 and 5 Vertical Sets how many parts the screen should be divided vertically Five adjustment levels 1 2 3 4 and 5 Screen Divider The screen can be divided into several images A number of screens can be selected with a different layout when dividing e Select a mode in Screen Divider e Select a display in Display Selection Adjusting the PDP Display e The selection will be set up by pressing a number in the selected mode Safety Sc
19. resolution and the frequency of the video Adaptor Compare these values with the data in the Preset Timing Modes Chart The picture rolls vertically mO PF F O p Check if the signal cable is securely connected Re connect it if necessary Refer to Connecting a Computer The image is not clear picture 1s blurred Run Frequency Coarse and Fine tuning Turn on again after removing all accessories video extension cable etc Set the resolution and frequency to the recommended ranges The picture image is unstable and shakes Pe O PF 2 PF O Check if the resolution and frequency set for the computer video card falls in the range supported by the PDP Display If not reset them referring to the current Information under the PDP Display menu and Preset Timing Modes Ghost images are shown in the picture Check if the resolution and frequency set for the computer video card falls in the range supported by the PDP Display If not reset them referring to the current Information under the PDP Display menu and Preset Timing Modes The image is too light or too dark Adjusts the Brightness and Contrast Refer to the Brightness Contrast Q The screen color is inconsistent Adjust color using Custom under OSD Color Adjustment menu o 7 OF O a O Troubleshooting The color image is distorted by dark shadows Adjust color using Custom under OSD Color Adjustment menu The color white is poor Adjust color using Custom under
20. source for the selected Display to DP 12 Channel Channel arrow appears when the Input Source is TV HDMI2 may not be supported depending on the product amp DP may not be supported depending on the product TV Source can be selected only in products with TV and controlling channels is allowed only when Input Source is TV The Input Source Control feature is available only for the displays whose power status is ON Fa Image Size PC BNC DVI DP 1 Click Image Size of the main icons and the Image Size control screen appears Multiple Display Control File Remote Control Safety Lock Por Selection Lamp Control Options Help Select Idle Refresh PC Un PC BNC OWI DP 16 9 4 3 Ye Info Grid shows some basic information necessary to Image Size Control 1 W Power Status Shows the power status of the current display 2 Image Size Shows the current Image Size of the display in use 3 Input Info Grid displays only the displays whose Input Source is PC BNC DVI and DP 4 PC Source Click Image Size in the main menu to display the PC BNC DVI and DP tabs The Image Size Control button controls Image Size available for PC BNC DVI and DP 5 Video Source Using the Image Size adjustment button you can adjust the Image Size to a value available in the PC BNC DVI and DP DP may not be supported depending on the product amp The Input source of MagicInfo works only on Ma
21. the input signal is interlaced scan it cannot be available with progressive scan signal 1 Off 2 On Sound Available Modes e J PC DVI BNC gt av HDMI X Component Mode NTS The PDP Display has a built in high fidelity stereo amplifier 1 Standard Selects Standard for the standard factory settings 2 Music Selects Music when watching music videos or concerts 3 Movie Selects Movie when viewing movies 4 Speech Selects Speech when watching a show that is mostly dialogue 1 e news 5 Custom Selects Custom if you want to adjust the settings according to your personal preferences Custom La kt The sound settings can be adjusted to suit your personal preferences Adjusting the PDP Display Note e You can hear the sound even when sound value is set to 0 e Ifyou adjust sound using Custom function Mode will turn to Custom mode Bass Emphasizes low frequency audio Treble Emphasizes high frequency audio Balance Balance Lo R 5o Mowe Cf Adjust Return Allows you to Adjusts the sound balance between the left and right speakers Auto Volume ba LS Reduces the difference in volume control between broadcasters 1 Off 2 On SRS TS XT G KA SRS TS XT is a patented SRS technology that solves the problem of playing 5 1 multichannel content over two speakers TruSurround delivers a compelling virtual surround sound experience through any two speaker playback system
22. the password during the OSD adjustment or to use MagicInfo The button is used to select Digital channels Electronic Program Guide EPG display Note This button 1s disabled for this PDP display Adjusts the audio volume Press this button to switch to MagicInfo or PC mode or a con nected external input source DTV menu display 8 TOOLS 9 Up Down Left Right buttons 10 i INFO 11 COLOR BUTTONS 12 FILE TTX MIX 13 MTS DUAL 14 E ENTER PRE CH Introduction Note This button 1s disabled for this PDP display Use to quickly select frequently used functions Note This button 1s disabled for this PDP display Moves from one menu item to another horizontally vertically or adjusts selected menu values Current picture information is displayed on the upper left corner of the screen Press to add or delete channels and to store channels to the favorite channel list in the Channel List menu Note This button 1s disabled for this PDP display TV channels provide written information services via teletext Teletext Buttons G62 02 02 C8200 0 amp POS O08 08 Note This button 1s disabled for this PDP display Note This button 1s disabled for this PDP display MTS You can select MTS Multichannel Television Stereo mode Audio Type MTS S Mode Default FM Stereo Mono Mono Manual Change Stereo Mono Stereo SAP Mono gt SAP Mono DUAL STEREO MONO DU
23. which the power status is ON a Maintenance Y Lamp Control 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen Image Lock EEE aan E CER N r ae Se pan LI Manual Lamp Control aie 3 Ambient Light Reference jorr M Lamp Value U Je An Info Grid showing several basic data items appears 1 Maintenance Allows the Maintenance Control function for all input sources 2 Lamp Control Automatically adjusts the backlight of the selected display at a specified time The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control Allows you to adjust the backlight of the selected display regardless of the time The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control 3 Ambient Light Detects the ambient light intensity at the designated monitor and automatically adjusts the picture brightness You can specify a Reference value and designate a monitor that will automatically determine Lamp Value the light intensity from the lamp based on the ambient light intensity Ambient Light is only supported for models that have a brightness sensor and is only enabled when Ambient Brightness Mode is selected in the Lamp Control menu Auto Lamp Control and Manual Lamp Control are only enabled when User Control Mode is selected in the Lamp Control menu k The Maintenance Contr
24. you may use the lower part of the package box as a temporary stand for product test or operation check Unpacking Introduction PDP Display Manuals LY Quick Setup Guide Warranty Card User s Guide Not available in all loca tions Cables Power Cord D Sub Cable Others Remote Control Batteries AAA X 2 Ferrite Core for Power Cord Not available in all loca tions Options P64FT Model Only Pen battery charger Adapter Power Cord 9 USB Dongle Zigbee Touch Pen IWB P1 Samsung Interactive white board Introduction Sold separately DVI Cable Network Box HDMI Cable BNC COMPONENT Cable COMPOSIT Cable HDMI DVI Cable T Warning e The network box is not compatible with the Interactive Whiteboard program Ferrite Core e The ferrite cores are used to shield the cables from interference e When connecting a cable open the ferrite core and clip it around the cable near the plug Your PDP Display P note The PDP device may interfere with an amateur radio or AM radio Introduction Front 1 2 SOURCE CH MENU SOURCE button SOURCE Switches from PC mode to Video mode Changing the source is only allowed for external devices that are connected to the PDP Display at the time PC DVI AV HDMI MagicInfo Component BNC Enter button Activates a highlighted menu item Note e This product is not compati
25. 1 01 112 discard the number in the first digit like below example PowerOn amp ID 0 Header command DATA DATA 1 ID MG CheckSum OAA 0x1 l Header command DATA DATA 1 ID Length 12 If you want to control every mechanism connected with Serial Cable regardless of its ID set ID part to OxFE and send commands At the time each product will follow commands but it will not respond with ACK Power Control e Function Personal Computer turns TV Monitor power ON OFF e Get Power ON OFF Status ID CheckSum Ko e Set Power ON OFF Header command DATA DATA ID BE a CheckSum OAA Oxi 1 Power Power Power code to be set on TV Monitor 1 Power ON 0 Power OFF e Ack DATA pate um Power Same as above e Nak Length Introduction amor 3 om eee ERR Error code that shows what occurred error is e Volume Control e Function Personal Computer changes volume of TV Monitor e Get Volume Status CheckSum po e Set Volume Header command DATA DATA ID PE CheckSum OxAA 0x2 0x2 2 Volume Volume Volume value code to be set on TV Monitor 0 100 e Ack DATA ID rane um Volume Same as above e Nak DATA paa um ERR Error code that shows what occurred error is e Input Source Control e Function Personal Computer changes input source of TV Monitor e Get Input Source Status ID CheckSum o Intr
26. 5 8000 4726 08000 726786 800 22273 080 100 2255 9200 21230 800 SAMSUNG 726 7864 Africa 0800 SAMSUNG 726 7864 0860 SAMSUNG 726 7864 http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com http www samsung com The image on a monitor is composed of red green and blue dots The closer the dots the higher the resolution The distance be tween two dots of the same color is called the Dot Pitch Unit mm The screen must be redrawn several times per second in order to create and display an image for the user The frequency of this repetition per second 1s called the Vertical Frequency or Refresh Rate Unit Hz Example If the same light repeats itself 60 times per second this is regarded as 60 Hz The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle The in verse number of the Horizontal Cycle is called Horizontal Fre quency Unit kHz Showing the horizontal lines of the screen from the top to the bot tom sequentially is called the Non Interlace method while show ing odd lines and then even lines in turn is called the Interlace method The Non Interlace method is used for the majority of monitors to ensure a clear image The Interlace method is the same as that used in TVs This is a
27. AL 1 DUAL Il and MONO NICAM MONO NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV This button is used to return to the immediately previous channel 15 K MUTE 16 W CHP A 17 TV 18 MENU 19 _ RETURN 20 Ul EXIT 21 MagicInfo User Installation Guide ote Introduction Note This button is disabled for this PDP display Pauses mutes the audio output temporarily This is displayed on the lower left corner of the screen The audio comes back on if MUTE or VOL is pressed in the Mute mode In TV mode selects TV channels Note This button 1s disabled for this PDP display Selects the TV mode directly Note This button 1s disabled for this PDP display Opens the on screen menu and exits from the menu or closes the adjustment menu Returns to the previous menu Exits from the menu screen MagicInfo Quick Launch Button ote This button is disabled for products that do not support MagicIn fo e Be sure to call an installation expert of Samsung Electronics to install the product e The warranty becomes invalid if the product is installed by someone other than a professional authorized by Samsung Electronics e A Samsung Electronics service center can provide details Introduction Tilt Angle and Rotation 1 The product can be tilted up to 15 degrees from a vertical wall 2 Touse the p
28. Check the polarities of the batteries Check if the batteries are empty Check if the power is on Q amp A Troubleshooting A Check if the power cord is securely connected A Check if a special fluorescent or neon lamp is on in the vicinity How can I change the frequency The frequency can be changed by reconfiguring the video card Note That video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details Q How can I Adjust the resolution Windows XP Set the resolution in the Control Panel Appearance and Themes Display Settings A Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can I set the Power Saving function Windows XP Control Panel Appearance and Themes Display Enable the powersaving feature in Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual A Windows ME 2000 Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual How can I clean the outer case PDP Panel Disconnect the power cord and then clean the PDP Display with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water e
29. NGARY 06 80 SAMSUNG 726 7864 http www samsung com ITALIA 800 SAMSUNG 726 7864 http www samsung com KOSOVO 381 0113216899 LUXEMBURG 261 03 710 http www samsung com MACEDONIA 023 207 777 MONTENEGRO 020 405 888 NETHERLANDS 0900 SAMSUNG http www samsung com 0900 7267864 0 10 Min NORWAY 815 56 480 http www samsung com POLAND 0 801 ISAMSUNG 172678 http www samsung com 022 607 93 33 PORTUGAL 80820 SAMSUNG 7267864 http www samsung com RUMANIA 08010 SAMSUNG 08010 7267864 http www samsung com doar din rejeaua Romtelecom tarif local 021 206 01 10 din orice retea tant normal SERBIA 0700 SAMSUNG 0700 726 http www samsung com 7864 SLOVAKIA 0800 SAMSUNG 0800 726 http www samsung com sk 786 SPAIN 902 1 SAMSUNG 902 172 http www samsung com 678 SWEDEN 0771 726 7864 SAMSUNG __ http www samsung com SWITZERLAND 0848 SAMSUNG 7267864 http www samsung com ch CHF 0 08 min http www samsung com ch fr French U K 0330 SAMSUNG 7267864 http www samsung com EIRE 0818 717100 http www samsung com LITHUANIA 8 800 77777 http www samsung com LATVIA 8000 7267 http www samsung com ESTONIA 800 7267 http www samsung com TURKEY 44477 11 http www samsung com CIS RUSSIA 8 800 555 55 55 http www samsung com GEORGIA 8 800 555 555 Appendix CIS ARMENIA 0 800 05 555 AZERBAIJAN 088 55 55 555 KAZAKHSTAN 8 10 800 500 55 500 GSM http www samsung c
30. OSD Color Adjustment menu The Power Indicator blinks The PDP Display is currently saving the changes made to the settings to the OSD memory The screen is blank and the power indicator light blinks every 0 5 or 1 seconds The PDP Display is using its power management system Press any key on the keyboard The PDP Display is using its power management system Press a key on the keyboard The screen is blank and it is blinking If you see the TEST GOOD message on the screen when you pressing the MENU button check the cable connection between the PDP Display and the computer to ensure that the con nector is properly connected Problems related to Audio Note Problems related to audio signals and their solutions are listed below Q A E OPF No sound Ensure that the audio cable is firmly connected to both the audio in port on your PDP Display and the audio out port on your sound card Refer to the Connecting a Computer Check the volume level The sound level is too low Check the volume level If the volume is still too low after turning the control to its maximum check the volume control on the computer sound card or software program The sound is too high or too low Adjusts the Treble and Bass to the appropriate levels Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed Q A A A The remote control buttons do not respond
31. Preset Timing Modes for the resolutions or frequencies supported by the PDP Display Maintenance and Cleaning 1 Maintaining the PDP Display Case Clean with a soft cloth after disconnecting the power cord Troubleshooting e Do not use benzene thinner or other flammable substan ces or a wet cloth 2 Maintaining the Flat Panel Display Screen Clean with a soft cloth cotton flannel smoothly e Never use acetone benzene or thinner LL lsg They may cause flaws or deformation of the screen sur face e The user will be required to pay costs and related expenses for repairing damages caused Symptoms and Recommended Actions Note A PDP Display recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the PDP Display to become blank have poor coloring become noisy and video mode not supported etc In this case first check the source of the problem and then contact a Service Center or your dealer 1 Check if the power cord and the video cables are properly connected to the computer 2 Check if the computer beeps more than 3 times when booting If it does request an a service for the main board of the computer 3 Ifyou installed a new video card or if you assembled the PC check if you installed the Adaptor video 4 Check if the scanning ratio of the video screen is set to between 50 Hz 85 Hz Do not exceed 60H
32. S Video k The Input source of MagicInfo works only on MagicInfo model k The Input source of TV works only on TV model The Image Size Control feature is available only for the displays whose power status is ON Time 1 Click Time of the main icons and the Time Control screen appears Multiple Display Control File Remote Control SafetyLock Port Selection Lamp Control Idle Refresh Sot Clock Month Day Year s BE Ng klinika ATPM ee E _ Apply Timor Timer Inactivated Activate Timer Inactivated Activate Timer Inactivated Activate Holiday Management N N Ye Info Grid shows some basic information necessary to Time Control 1 Set clock Set the current time for the selected display PC Time To change the current time first change the PC Time 2 Timer Sets up Timer1 Timer2 Timer3 and Holiday Management 3 Shows whether Timer is activated The Input source of MagicInfo works only on MagicInfo model k The Input source of TV works only on TV model Time Control is available only for the displays for which the power status is ON Time Setting up Timer and Holiday Management 1 1 Setting up Timer1 Timer2 and Timer3 1 2 3 4 5 6 2 Timer 1 Actiwe Hour Minute Sun Mon Tue Wed Thu On Time Sets the time in hours in minutes and as AM PM for turning the selected monitor on Off Time Sets the time in hours in
33. and Pattern type it can be set to 1 5 10 20 or 30 The Input source of MagicInfo works only on MagicInfo model The Input source of TV works only on TV model amp The Maintenance Control feature is available only for the displays whose power status is ON _ Maintenance Na Video Wall 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen Multiple Display Control File Remote Control SafetyLock Port Selection Lamp Control Refresh Video Wall Video Wall Control 1 Video Wall A Video Wall is a set of video screens that are connected together so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen 2 Video Wall Control Video Wall properties can be configured es MUL Video all O Video Wall On Off Format Full Natural 1 On Off Turns on off the Video Wall function of the selected display 2 Format The format can be selected to see a divided screen e Full e Natural 3 Video Wall Screen divider The screen can be divided into You can select a number of screens with a different layout when dividing Select a mode from Screen divider Select a display from Display Selection The place will be set up by pressing a number in the selected mode The maximum number of monitors that can be arranged Horizontal X Vertical 100 Up to 15 monitors can be arranged in a row The maxim
34. as your computer can be connected to the PDP Display For detailed information on connecting AV input devices refer to the contents under Adjusting Your PDP Display e The PDP Display s configuration at the back may vary slightly depending on the PDP Display model Connecting AV Devices Soe ON PERU 6690 086 pA 3 Connections Connect an audio cable to the audio output port on the external device and AV COMPONENT AUDIO IN R AUDIO L port on the monitor and connect the video output port on the external device to the AV IN VIDEO port on the monitor Play the DVD VCR or Camcorder with a DVD disc or tape inserted Select AV using the SOURCE button on the front of the PDP display or on the remote Connecting to a Camcorder 4 The ALCS DED l OUTPUT RnB E e A i ee a Paga m Oe ees Locate the AV output jacks on the camcorder They are usually found on the side or back of the camcorder Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV COMPONENT AUDIO IN R AUDIO L on the PDP Display Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN VIDEO on the PDP Display Select AV for the Camcorder connection using the SOURCE button on the front of the PDP Display or on the remote control Then start the Camcorder with a tape inserted Note audio video cables shown here are usually included with a Camcorder I
35. ble with MagicInfo o MENU button MENU Opens the on screen menu and exits from the menu Also use to exit the OSD menu or return to the previous menu VOL Moves from one menu item to another horizontally or adjusts selected menu val ues When OSD is not on the screen push the button to adjust volume VSELA Moves from one menu item to another vertically or adjusts selected menu values O Power button O J Use this button for turning the PDP Display on and off Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions For energy conservation turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods Remote Control Sensor Aim the remote control towards this spot on the PDP Display Introduction Rear Note For detailed information concerning cable connections refer to Connecting Cables under Setup The PDP Display s configuration at the back may vary slightly depending on the PDP Display model O POWER IN The power cord plugs into the PDP Display and the wall plug Rs232C OUTAN RS232C Serial PORT MDC Multiple Display Control Program Port Ores IN PC Connection Terminal Input e Usea D Sub Cable 15 pin D Sub PC mode Analog PC e Connect the RGB IN port on the monitor to the BNC port on the PC using the RGB to BNC cable
36. c that may attract the attention of children and to the product e Your children may hang onto the product causing it to fall and this may result in personal injury or death J Be careful that children do not place the battery in their mouths when removed from the remote control Place the battery in a location that children or infants cannot reach e If children have had the battery in their mouths consult your doctor immediately L When replacing the battery insert it with the right polarity e Otherwise the battery may become damaged or it may cause fire personal injury or damage due to leakage of the internal liquid Use only the specified standardized batteries and do not use a new battery and a used battery at the same time e Otherwise the batteries may be damaged or cause fire personal in jury or damage due to a leakage of the internal liquid The batteries and rechargeable batteries are not ordinary refuse and must be returned for recycling purposes The customer is responsible for returning the used or rechargeable batteries for recycling e The customer can return used or rechargeable batteries to a nearby public recycling center or to astore selling the same type of the battery or rechargeable battery L Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater e This may reduce the lifetime of the product and may result in fire Safety Instruct
37. choice l PC 2 DVI 3 AV 4 HDMI 5 MagicInfo Enabled when a network box is connected 6 Component 7 BNC Note e The direct button on the remote control is the SOURCE button Edit Name A Adjusting the PDP Display Cable STB ai Satellite STB Name the input device connected to the input jacks to make your input source selection easier VCR DVD Cable STB HD STB Satellite STB AV Receiver DVD Receiver Game Camcorder DVD Combo DHR PC Note e Set Edit Name to PC when a PC is connected via the HDMI or DVI port In most other cases set Edit Name to AV Note that Edit Name should be set to the connected source device 1f the source device s signal is 640 x 480 720p 1280 x 720 or 1080p 1920 x 1080 because these signals are compatible with both AV and PC input e The Picture menu changes depending on the input signal and Edit Name Picture PC DVI BNC Mode Available Modes PC DVI BNC Elav HDMI H Component P Note e MagicInfo can only be enabled when a network box is connected e The HDMI port and network box cannot be connected at the same time MagicBright Li The MagicBright function is only enabled in PC mode The function offers a picture that 1s twice as bright and vivid as conventional monitors so that users various needs to prepare documents use the Internet view videos etc are satisfied Adjusting the PDP Disp
38. ction Symptom Horizontal Bar with Black Color move up and down Horizontal Bar wath Black color r Lir iI l IVIC OZ348 20 30 UA102 21 10 Note Please check CD s User Guide at OSD Function some model s will not available e3 Apply the Screen Pixel function on Product e Apply the Screen Pixel function Symptom Dot with Black Color move up and down FLIGHT TIME OZ348 20 30 UA102 21 10 e Apply the Screen Bar function Symptom Horizontal Vertical Bar with Black Color move up and down Information ma i FLIGHT Horizontal Bar OZ5 UA102 Note Please check CD s User Guide at OSD Function some model s will not available Apply the Screen Erasing function on Product e Apply the Screen Erasing function Symptom 2 Vertical blocks move with erasing the display gt HT TIME OZ348 20 30 UA102 21 10 Note Please check CD s User Guide at OSD Function some model s will not available Appendix Contact SAMSUNG WORLDWIDE E note If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center North America U S A 1 800 SAMSUNG 726 7864 http www samsung com CANADA 1 800 SAMSUNG 726 7864 http www samsung com MEXICO 01 800 SAMSUNG 726 7864 http www samsung com Latin America ARGENTINA 0800 333 3733 http www samsung com BRAZIL 0800 124 421 http www samsung com 4004 0000 CHILE 800 SAMSUNG 726
39. densing Specifications Environmental considerations Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This PDP Display can be installed on any Plug amp Play compatible system The interaction of the PDP Display and the computer systems will provide the best operating conditions and PDP Display settings In most cases the PDP Display installation will proceed auto matically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology with preci sion of Ippm one millionth above are used for this product But the pixels of RED GREEN BLUE and WHITE Color appear to be bright sometimes or some black pixels may be seen This is not from bad quality and you can use it without any problems For example the number of TFT LCD sub pixels contained in this product are 6 220 800 Note Design and specifications are subject to change without prior notice pa Class B Information Communication equipment for residential use This device is registered for EMC requirements for home use Class B It can be used in all areas Class B equipment emits less electromagnetic waves than Class A equipment Recommendation EU Only P64FT Model Only Hereby Samsung Electronics declares that this PDP Display is in compliance with the essential requirements and other relevant provisions of Dir
40. e inverse number of the Horizontal Cycle is called the Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency ofthis repetition is called the Vertical Frequency or Refresh Rate Unit Hz Information For Better Display ba Adjust the computer resolution and screen injection rate refresh rate on the computer as described below to enjoy the best picture quality You can have an uneven picture quality on screen 1f the best picture quality 1s not provided for PDP e Resolution 1920 x 1080 e Vertical frequency refresh rate 60 Hz E3 PDP panels manufactured by using advanced semiconductor technology with a preci sion of Ippm one millionth and above is used for this product But the pixels of RED GREEN BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen This is not from bad quality and you can use it without any problems e For example the number of PDP sub pixels contained in this product are 6 220 800 63 When cleaning the monitor and the panel outside please apply the recommended small amount of cleaner by using a soft cloth to polish Do not force the PDP area but rub softly If excessive force 1s applied you may stain it Ea If you are not satisfied with the picture quality you can get better quality of picture by performing the Auto Adjustment function
41. e signal balance Signal Control 1 R Gain 2 G Gain 3 B Gain 4 R Offset 5 G Offset 6 B Offset Size LJ The Size can be switched 1 16 9 2 4 3 Picture AV HDMI Component Mode Available Modes e J PCc DVI BNC gt Elav HDMI Adjusting the PDP Display 4 Component Mode ro Dynamic E Standard Movie EO Custom Move F Enter Return The PDP Display has four automatic picture settings Dynamic Standard Movie and Cus tom that are preset at the factory Dynamic Standard Movie or Custom can be activated 1 Dynamic 2 Standard 3 Movie 4 Custom Custom L A By using the on screen menus the contrast and brightness can be changed to your personal preference Contrast Contrast Move Adjusts the Contrast Brightness Brightness Move Adjusts the Brightness Sharpness Pa Sharpness Move Adjusts the picture Sharpness Color Adjusts the picture Color Tint Adjusting the PDP Display Adds a natural tone to the display Color Tone LIS Ecot oo Want Warm Move Enter Return The color tones can be changed The individual Color components are also user adjustable 1 Off 2 Cool2 3 Cooll 4 Normal 5 Warml 6 Warm2 Note If you set the Color Tone to Cool2 Cooll Normal Warm1 or Warm2 the Color Temp function is disabled Color Temp LEIS Color Temp 5000K
42. e to the product or fire due to damage to the cable Safety Instructions L Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables e Otherwise it may fall and result in electric shock damage to the product or fire due to damage to the cable J Make sure that the ventilating opening is not blocked by a table or curtain e Otherwise it may result in fire due to an increase in the internal tem perature CJ Do not place any containers containing water vases flowerpots med icines as well as any metal on the product e Ifwater or a foreign material enters the product disconnect the power cord and contact a Service Center e This may result in a product malfunction electric shock or fire J Do not use or keep combustible spray or flammable material near the product e Otherwise this may result in an explosion or fire Do not insert any metal such as chopsticks coins pins and steel or flammable objects such as matches or paper inside the product through JJ the ventilating openings input and output terminals etc e If water or foreign material enters the product disconnect the power cord and contact a Service Center e Otherwise this may result in electric shock or fire J When using a fixed screen for a long time an afterimage or stain may occur e Ifyou are not using your product for a long period of time put it i
43. ear click Next The License Agreement screen will appear Click Yes The Customer Information window will appear Register the user information and click Yes The Choose Destination Location window will appear Specify the file location to install to and click Next Note If the file location is not specified the program will be installed in the default file location The Start Copying Files window will appear Confirm the file location and click Next The installation progress screen will appear Using the Software 9 The InstallShield Wizard Complete screen will appear Click Finish Note Select Launch Serial MDC and click Finish The MDC program will immediately be run 10 Ifthe installation is successfully completed the quick Serial MDC execution icon will appear on the desktop MDC execution icon may not appear depending on specification of computer system or monitor If that happens press F5 Key Installation Problems The installation of MDC can be affected by such factors as the video card motherboard and the network environment Uninstall The MDC program can be removed only by using the Add or Remove Programs option of the Windows Control Panel Perform the following steps remove MDC Select Setting Control Panel on the Start menu and then double click Add Delete a program Select Serial MDC from the list and then click the Add Delete button M Using Serial MDC
44. ection Lamp Control Options Help Refresh PIP Source 1 All Inputs Ye Info Grid shows some basic information necessary to PIP Source Control 1 PIP Source PIP Source can be controlled with turning on the PDP Display power 2 PC Changes the source of the PIP of the selected display to PC 3 BNC Changes the source of the PIP of the selected display to BNC 4 DVI Changes the source of the PIP of the selected display to DVI 5 TV Changes the source of the PIP of the selected display to TV 6 DIV Changes the source of the PIP of the selected display to DTV 7 AV Changes the source of the PIP of the selected display to AV 8 S Video Changes the source of the PIP of the selected display to S Video 9 Component Changes the source of the PIP of the selected display to Component 10 HDMI1 HDMI2 Changes the source of the PIP of the selected display to HDMI 11 DP Switches the PIP Source of the selected Display to DP HDMI2 may not be supported depending on the product DP may not be supported depending on the product Some of the PIP Sources may not be available for selection depending on the input source type of the Main Screen The Input source of MagicInfo works only on MagicInfo model The PIP Control feature is available only for the displays whose power status is ON and the PIP function is set to ON ay Settings Picture 1 Click Settings of the main icons and the Set
45. ective 1999 5 EC USA only Dispose unwanted electronics through an approved recycler To find the nearest recycling location go to our website www samsung com recyclingdirect Or call 877 278 0799 FCC INFORMATION FOR THE CONSUMER P64FT Model Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Specifications e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is con nected e Consult the dealer or an experienced radio TV technical for help This device complies with Part 15 of the FCC s Rules Operation is subject to the following two Conditions
46. emperatures high humidity and exposed to chemical substances and where it operates for 24 hours such as at airports train stations etc Failure to do so may cause serious damage to your monitor 3 Ensure that at least two persons lift and move the product e Otherwise it may be dropped and cause personal injury and or dam age the product L When installing the product in a cabinet or rack make sure that the front end of the bottom of the product does not project out e Otherwise it may fall or cause personal injury e Use a cabinet or rack of a size appropriate to the product JDO NOT PLACE CANDLES MOSQUITO REPELLANT CIGA RETTES AND ANY HEATING APPLIANCES NEAR THE PROD UCT e Otherwise this may result in fire L Keep heating appliances as far away from the power cord or the prod uct as possible e Otherwise this may result in electric shock or fire Safety Instructions 3 Do not install it in a badly ventilated location such as a bookcase or fp closet il _ O gt Otherwise this may result in fire due to an increase in the internal temperature When putting the product down make sure to put it down softly L Do not place the front of the product on the floor e Otherwise this may result in damage to the screen display L Ensure that an authorized installation company installs the wall mount e Otherwise it may fall and cause personal injury e Make sure to i
47. et USB cable should not be disposed of with other household waste at the end of their working life To pre vent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Europe only Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate bat terie
48. f not check your local electronics store If your camcorder is stereo you need to connect a set of two cables Connections Connecting the BNC to BNC cable amp o O O BREST F 00000 OIE KK GF 1 Connect the BNC COMPONENT IN R Pp G Y B Pp ports on the monitor to the BNC port on the external device using the BNC to BNC cable 2 Select BNC using the SOURCE button on the front of the PDP Display or on the remote control Connecting Using a DVI Cable 1 Connect between the DVI OUT port on the PDP Display and the input port on another monitor using a DVI cable 2 Connect between the AUDIO OUT port on the PDP Display and the audio input port on another monitor using a stereo cable 3 Select DVI using the SOURCE button on the front of the PDP Display or on the remote control Note DVI OUT does not support HDCP Connections Connecting Using a HDMI Cable 1 Connect input devices such as a Blu Ray DVD player to the HDMI IN terminal of the PDP Display using an HDMI cable 2 Select HDMI using the SOURCE button on the front of the PDP Display or on the remote control Note In HDMI mode only PCM format audio is supported When the HDMI cable to the PC ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted Connecting Using a DVI to HDMI Cable 1 Connect the DVI
49. function that provides the best quality screen for the user by allowing the computer and the monitor to exchange informa tion automatically This monitor follows the international standard VESA DDC for the Plug amp Play function The number of horizontal and vertical dots used to compose the screen image is called the resolution This number shows the ac curacy of the display A high resolution is good for performing multiple tasks as more image information can be shown on the screen Example If the resolution 1s 1920 x 1080 this means the screen is composed of 1920 horizontal dots horizontal resolution and 1080 vertical lines vertical resolution Appendix SRS TS XT This feature outputs sonorous and vivid 3D sound as for 5 1 chan nel speaker sound but through a 2 channel speaker It has a good effect when stereo signals are input Multiple Display Control A Multiple Display Control MDC is an application allowing MDC various displays to be easily and simultaneously operated on a PC RS 232C a standard of serial communication is used for com municating between a PC and a display Correct Disposal Correct Disposal of This Product Waste Electrical amp Electronic Equipment Europe only Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger heads
50. gicInfo model amp The Input source of TV works only on TV model Image Size Control is available only for the displays for which power status is ON EO Image Size TV AV S Video Component DVI HDCP HDMI1 HDMI2 DTV 1 Click Image Size of the main icons and the Image Size control screen appears 5 Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Help Refresh Vireo Source 1 TY AV S Video Component HDMI1 HOMI DTV Image Size Auto Wide Wide Zoom Zoom Zoom 1 Zoom 2 4 3 Screen Fit Wide Fit Lustom el Se ee Ye Info Grid shows some basic information necessary to Image Size Control 1 To adjust Image Size in TV AV S Video Component HDMI1 HDMI2 or DTV mode click the Video Source tab Select the display you want to adjust by using the Select button or by checking the checkbox 2 Info Grid displays only the display having TV AV S Video Component HDMI1 HDMI2 or DTV as input source 3 Switch Image Size of the selected display randomly 4 The screen modes can only be adjusted when a TV PAL only is connected and the Image Size item is set to Auto Wide HDMI2 may not be supported depending on the product Custom may not be supported depending on the product Auto Wide Zoom1 and Zoom are not available for selection when the input signal type for Component and DVI HDCP is 720p or 1080i The Auto Wide mode is available only for TV AV and
51. h no r gim png L et cc mS Unit mm Installation VESA Bracket e When installing VESA make sure to comply with the international VESA standards e Purchasing VESA Bracket and Installation Information Please contact your nearest SAMSUNG Distributor to place an order After your order is placed installation professionals will visit you and install the bracket e Atleast 2 persons are needed in order to move the PDP Display e SAMSUNG is not responsible for any product damage or any injury caused by installation at customer s discretion Dimensions ee Unit mm AN Notice For securing the bracket on a wall use only machine screws of 6 mm diameter and 8 to 12 mm length Introduction Accessories sold separately e Dimension with other accessories 136 3 o MO i b E 5 588 R 2170 281 5 54 35 Unit mm Wall Bracket Installation e Contact a technician for installing the wall bracket when the installation is done by the customer 73 5 736 0 742 0 311 4 Rail Inside SAMSUNG Electronics is not responsible for any damages to the product or harm to customers e This product is for installing on cement walls The product may not stay in place when installed on plaster or wood Components Only use the components and accessories shipped with the product
52. he same still image is not displayed for long hours e When you need to display the same still image for long hours be sure to activate Screen saver at regular intervals e Itis best to activate Screen saver when the Samsung Interactive Whiteboard is not in use e Using screen saver Activating screen saver when the Interactive Whiteboard software is not in use e Go to MENU gt Setup gt Safety Screen in the onscreen display menu and select Pat tern mode A screen saver pattern will activate Scroll ar Eraser All White Activating screen saver when the Interactive Whiteboard software is in use Click ina and select Eliminate Image Retention in the Interactive Samsung Interactive Whiteboard A screen saver pattern will be activated Connections BT MAL KO Event Recording fy Video Capture 7 Spotlight 4 Magnifier Screen Shade CR Zoom In Out oO Device Setting K Pen Setting BN On Screen Keyboard E Eliminate Image Retention It is recommended that you activate screen saver for a short period of time before you power off the PC e Activation of Screen saver after the interactive whiteboard program is closed e Ifthe PC is turned off Screen saver will be active for a specified time before the PC powers of e Ifthe PC is not turned off The interactive whiteboard program will be closed only Connecting to Other devices e AV input devices such as DVD players VCRs or camcorders as well
53. he set period of time specify a time for execution e Mode Scroll 1 5 sec e Mode Bar Eraser 10 50 sec e Mode All White Pattern 1 5 10 20 30 min This function prevents after images on the screen by moving all the pixels on the PDP according to a pattern Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time C Scroll Eraser Pattem H Moe Enter O Return Adjusting the PDP Display This function prevents after images on the screen by moving long black and white vertical lines Eraser Pixel Shift Hl Timer This function prevents after images on the screen by moving a rectangular pattern All White Move Enter Retum This function prevents after images on the screen by changing the color of pixels to white Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time Pattern Pixel Shift Timer J This function prevents after images on the screen by moving a diagonal pattern stored in the panel repeatedly Resolution Select Li Move Enter O Retum When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 60Hz 1280 x 768 60Hz 1360 x 768 60Hz or 1366 x 768 Adjusting the PDP D
54. in display screen that is appeared as window termination button is pressed If there s still noise after the automatic adjustment use the Fine Coarse adjustment function o When viewing a fixed screen for an extended period of time a residual image or blur 8 p g riness may appear Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time PRODUCT INFORMATION Image Retention Free D What is Image Retention Image retention may not occur when a PDP panel is operated under normal conditions Normal conditions are defined as continuously changing video patterns When the PDP panel is operated for a long time with a fixed pattern Phosphor degradation may occur and the brightness is decreased To prevent this the video pattern should be changed from time to time When viewing a still screen for a long time the brightness of any part which was bright in the previous fixed pattern becomes lower than that of its surroundings Information Visible ray pu Transparent Bus electrodes electrodes ITO Black Protection Transparent layer MgO dielectric layer Partition Phosphor Bottom Discharge dielectric layer Address electrodes Plasma ITO Indium Tin Oxide MgO Magnesium Oxide 6a Power Off Screen Saver or Power Save Mode e Turn the power off for 4 hours after 20 hours in use e Turn the power off for 2 hours after 12 hour
55. ions L Do not drop any objects onto the product or cause any impact to the product L Otherwise this may result in electric shock or fire L Do not use a humidifier near the product e Otherwise this may result in electric shock or fire LI When there is a gas leak do not touch the product or the power plug I 7j ventilate immediately e Ifa spark occurs it may cause an explosion or fire J If the product has been turned on for a long time the display panel L Do not install the product in a location low enough for children to reach e Otherwise it may fall and result in personal injury e Since the front part of the product is heavy install the product on a level and stable surface L Do not put any heavy objects on the product e This may result in personal injury and or damage to the product Introduction Package Contents Note Please make sure the following items are included with your PDP Display If any items are missing contact your dealer Contact a local dealer to buy optional items Checking the Contents of the Package a Lift up the package box by Check the contents of the Remove the Styrofoam and holding the grooves on both package vinyl cover sides of the package box Note e After unpacking the package make sure to check the contents of the package e Make sure to keep the package box for transporting the product in the future e After unpacking
56. isplay 60H7 by using this function Resolution Select you can have the picture displayed on the screen in the specified resolution Note Available in PC mode only 1 Off 2 1024 x 768 3 1280 x 768 4 1360 x 768 5 1366 x 768 Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 60Hz 1280 x 768 60Hz 1360 x 768 60Hz or 1366 x 768 60Hz Power On Adjustment O Return AE i Adjust the Power On time for the screen Caution Set the Power On time to be longer to avoid overvoltage Side Gray La 8 Select the brightness of the grey for the screen background 1 Off 2 Light 3 Dark Adjusting the PDP Display Reset Reverts the product settings to factory defaults The Reset function is only available when PC DVI is being used Image Reset Li Image Reset Ok bo Move Adjust O Retum rf Note Available in PC mode only The Reset function is not available when Video Wall is On Color Reset la kr Color Reset INA Cancel Move Adjust 9 Retum OSD Rotation AIS OSD Rotate 1 Landscape 2 Portrait Multi Control Available Modes J Pc DVI BNC gt Elav HDMI 4 Component Multi Control Assigns an individual ID to the SET Adjusting the PDP Display e ID Setup Assigns distinctive IDs to the SET e ID Input Use to select the transmitter functions of the individual SET Only a SET where the
57. lay 1 Entertain High brightness For watching motion pictures such as a DVD or VCR 2 Internet Medium brightness For working with a mixture of images such as texts and graphics 3 Text Normal brightness For documentations or works involving heavy text 4 Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the brightness and contrast by using the OSD menu Custom Lil By using the on screen menus the contrast and brightness can be changed to your personal preference Note By adjusting the picture using the Custom function MagicBright will change to Custom mode Contrast Contrast Adjusts the Contrast Brightness Brightness Adjusts the Brightness Sharpness Sharpness C eee Move Adjust _ Adjusts the Sharpness Color Tone Li Adjusting the PDP Display The color tones can be changed l PA 3 4 5 off Cool Normal Warm Custom Note If you set the Color Tone to Cool Normal Warm or Custom the Color Temp function is disabled If you set the Color Tone to Off the Color Control function is disabled Color Control LIT Adjusts individual Red Green Blue color balance Note If you adjust the picture by using the Color Control function Color Tone will turn to the Custom mode Red Green Blue Color Temp G Col
58. le Note You can adjust the bracket angle between 2 and 15 Make sure to use the top center and not the left or the right side of the product to adjust the angle Introduction Remote Control RS232C Cable connections interface RS232C 9 pin pin TxD No 2 RxD No 3 GND No 5 Bits rate 9600 bps Data Bits 8 bit Parity None Stop Bits 1 bit Flow control None Maximum length 15 m only shielded type e Pin assignment Pin Signal Data Carrier Detect Received Data Transmitted Data Data Terminal Ready Signal Ground Data Set Ready Request to Send Clear to Send Ol NN IW M B A N e Ring Indicator e RS232C cable Connector 9 pin D Sub Cable Cross reversed cable PI PI P2 P2 FEMALE Rx 20 aaa gt 3 Rx FEMALE Introduction Gnd SO ao 5 Gnd e Connecting method ug NG os ba ee ba ua Control codes e Get control ID CheckSum e Set control Header command DATA DATA Length ID CheckSum OxAA command 1 Value type e commanding words o o omeo O Joxz loto PU Pnput source const Jose o ooo seen Mode contro Joe ooo 6 Pironatreonrat ose a 7 Aatoadjusinentconrot oad ido fs Video wa Mode contol osc a po fayrok ios ID should show hexadecimal value of assigned ID but ID 0 should be OxFF Introduction Every communication will be made in hexadecimals and Checksum is the sum of all remainings If it exceeds two digits for example it is 11 FF 0
59. ly for NT 6 Blue Adjusts blue Color of the selected display Available only for NT 7 Color Tone Adjusts the Color Tone for the selected display 8 Color Temp Adjusts the Color Temp for the selected display 9 Brightness Sensor Adjusts the Brightness Sensor for the selected display 10 Dynamic Contrast Adjusts the Dynamic Contrast for the selected display DP may not be supported depending on the product Brightness Sensor may not be supported depending on the product The Input source of MagicInfo works only on MagicInfo model The Input source of TV works only on TV model Color Temp is only enabled if the Color Tone is set to Off This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed Settings nI PC Audio 1 Click Settings of the main icons and the Settings Control screen appears Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Idle Refresh OF All Inputs rT reble 1 Ca Balance LIO _ Ro Ni E a PEEPS k pa aaa BS ON O Sound Select Main Ee Je Basic information required to adjust Audio is displayed in the display window Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected and the default settings will be displayed if all display IDs are selected b
60. ly on MagicInfo model Color Temp is only enabled if the Color Tone is set to Off The Input source of TV works only on TV model k This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed gt Settings Picture PC 1 Click Settings of the main icons and the Settings Control screen appears Multiple Display Control File Remote Control Safety Lock Port Selection LampConirol Options Help Select Clear Idle Refresh gt PL PC BNC DVI DP Contrast 100 ni f APA AA Brightness 100 Red breen Blue Color Tone Eee Color Temp 10000K Brightness Sensor LIES f B BO m oh E E i Dynamic Contrast Je Basic information required to adjust settings is displayed Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected and the default settings will be displayed if all display IDs are selected by clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode 1 Picture PC Available only for PC BNC DVI and DP 2 Contrast Adjusts Contrast of the selected display 3 Brightness Adjusts Brightness for the selected display 4 Red Adjusts red Color of the selected display Available only for NT 5 Green Adjusts green Color of the selected display Available on
61. m the panel 3 SWI Performs the right click command 4 SW2 Functions as the Page Down key on the keyboard An other function can be assigned as required J SW3 Functions as the Page Up key on the keyboard An other function can be assigned as required 6 SW4 power switch 2 2 Pen Battery Charger No Parts Functions Power in Connects to the power cable via the adapter 2 LED Shows the charging status Stylus pen holders Charge the batteries on the stylus pens mounted in correct orientation Connections 2 3 Charging a Stylus Pen Battery ote e Apply a ferrite core when you charge a pen battery in the charger e tis recommended that you use a ferrite core when charging a stylus pen battery to avoid electro magnetic interference e Before you connect the cable open the ferrite core and wrap the cable around the ferrite core as shown below e Red LED Charging Orange LED Error Green LED Fully charged ote e Ifthe LED remains green when you charge a pen battery indicating fully charged but the pen cannot power on contact Samsung Customer Service Center e Charging a pen battery may fail unless the pen is mounted in correct orientation on the holder Connecting to a Stylus Pen 3 1 Attaching the Dongle To use a dedicated stylus pen for Whiteboard insert the dongle into the USB slot on your PC ote e Ensure the dongle is installed 1m or higher from the ground 3 2 Using a Stylus Pen
62. minutes and as AM PM for turning the selected monitor off Volume Selects the volume when the selected monitor is turned on Source Selects the external input source that will be displayed when the selected monitor is turned on Holiday Applies the Holiday Management function to the Timer Repeat Available selections include Once EveryDay Mon Fri Mon Sat Sat Sun and Manual Once The Timer goes off only once EveryDay EveryDay The Timer repeats daily Mon Fri The Timer repeats from Monday through Friday Mon Sat The Timer repeats from Monday through Saturday Sat Sun Sat Sun The Timer goes off on Saturday and Sunday e J J e Manual Select a day of the week you want the Timer to go off Setting Holiday Management The Holiday Management function specifies the dates in which the monitor will not be turned on or off by the Timer Holiday Management Month 1 Specifies the date 2 Delete All Deletes all of the holidays 3 Add Adds the specified date 4 T Deletes the schedule in the selected line The Holiday Management function can be turned on or off in the Timer setup menu The Input source of MagicInfo works only on MagicInfo model The Input source of TV works only on TV model ke Time Control is available only for the displays for which the power status is ON k Only enabled for a TV when Source is set to TV in On Time mode k Only enabled for a model with MagicInfo in
63. n TV Monitor 1 Full 0 Natural Ack Length Check ID Sum Video Wall Mode same as above e Nak DATA ea um ERR Error code that shows what occurred error is Safety Lock e Function Personal Computer turns Safety Lock function of TV Monitor ON OFF Can operate regardless of whether power is ON OFF e Get Safety Lock Status ID CheckSum o Introduction e Set Safety Lock Enable Disable Header command DATA DATA ID Length CheckSum Safety Lock Lock code to be set on TV Monitor 1 ON 0 OFF e Ack Header command Do Ack Nak r CMD Vall Length Check ID Sum OxAA OxFF 3 lt M oxsp Safety Lock Safety Lock Same as above e Nak DATA I Pa um ERR Error code that shows what occurred error is Connections Connecting a Computer O00000 ee r e aa LU i There are several ways to connect the computer to the monitor Choose one from the following options Using the D sub Analog connector on the video card e Connect the D sub to the 15 pin RGB IN port on the back of your PDP Display and the 15 pin D sub Port on the computer Using the DVI Digital connector on the video card e Connect the DVI Cable to the DVI IN port on the back of your PDP Display and the DVI port on the computer Connections TIITIIT aaaanono LI saa00000 GD i the HDMI digital output on the graphics card e C
64. nstall the specified wall mount CJ Install your product in a well ventilated location Ensure that there is a clearance of more than 4 inches 10 cm from the wall e Otherwise it may result in fire due to an increase in the internal tem perature J Ensure that the packaging vinyl is kept away from children e Otherwise it may result in serious harm suffocation if children play with it L If the height of your monitor is adjustable do not place any object or part of your body on the stand when lowering it e This may cause damage to the product or the person carrying it Clean When cleaning the PDP Display case or the surface of the TFT PDP screen wipe with a slightly moistened soft fabric L Do not spray cleaner directly onto the surface of the product e Otherwise this may result in the discoloration and distortion of the structure and the screen surface may peel off L When cleaning the power plug pins or dusting the power outlet clean it with a dry cloth e Otherwise it may result in fire LJ When cleaning the product make sure to disconnect the power cord e Otherwise it may result in electric shock or fire Others Safety Instructions JW hen cleaning the product disconnect the power cord and clean it with a soft dry cloth e Do not use chemicals such as wax benzene alcohol thinner mos quito repellant lubricant or cleaner e These may change the appearance of the prod
65. nter the PDP Display How can I play the video The video supports the MPEG1 and WMV codecs only Install the corresponding codec to play the video Note that some of the codecs can be incompatible Note Before calling for assistance check the information in this section to see 1f you can remedy any prob lems yourself If you do need assistance please call the phone number on the Information section or contact your dealer Specifications General General Model Name SyncMaster P64FP SyncMaster P64FT PDP Panel Size 64 inches 162 cm Display Area 1416 96 mm H x 797 04 mm V Pixel Pitch 0 738 mm H x 0 738 mm V Synchronization Horizontal 30 81 kHz Vertical 56 75 Hz Display Color 16 77M Resolution Optimum resolution 1920 x 1080 60 Hz Maximum resolution 1920 x 1080 60 Hz Maximum Pixel Clock 165MHz Analog Digital Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors DVI D In Out Can connect up to 10 PDP display units D sub AV Composite CVBS HDMI RS232C In Out PC Audio In Audio In Stereo Audio Out Stereo Dimensions W x H x D Weight 1503 5 x 894 0 x 99 4 mm 52 0 kg 59 1 x 35 1 x 3 9 inches 114 lbs VESA Stand 676 mm x 407mm Environmental considerations Operating Temperature 32 F 104 F 0 C 40 C Humidity 20 80 non con
66. nto sleep mode or use a moving screen saver J Set a resolution and frequency appropriate to the product e Otherwise your eyesight may be damaged LJ When using headphones or earphones do not turn the volume too high e Having the sound too loud may damage your hearing J To avoid eyestrain do not sit too close to the product Take a rest for at least five 5 minutes after using the monitor for one tx 1 hour e This reduces eye fatigue Safety Instructions L3 Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations e Otherwise it may fall and cause personal injury and or damage the product e If you use the product in a location exposed to vibrations it may damage the product and result in fire LI When moving the product turn the power off and disconnect the power plug antenna cable and all the cables connected to the product e Otherwise it may result in electric shock or fire J Ensure that children do not hang onto the product or climb up onto the product e The product may fall and cause personal injury or death L If you do not use the product for a long period of time disconnect the power cord from the power outlet e Otherwise this may result in overheating or fire due to dust and may result in fire due to electric shock or leakage ILJDo not place any heavy items or toys or confectionery such as cookies et
67. oduction e Set Input Source Header command DATA DATA ID Length CheckSum Input Source Input Source code to be set on TV Monitor Caution DVI VIDEO HDMII PC HDMI2 PC Get Only In the case of MagicInfo only possible with models include MagicInfo In the case of TV only possible with models include TV e Ack Header command BATA Ack Nak r CMD Vall ID Length Check Sum Source Input Source Same as above e Nak DATA um ERR Error code that shows what occurred error is Introduction e Screen Mode Control e Function Personal Computer changes Screen Mode of TV Monitor Cannot be controlled when Video Wall is on Caution Only works with models include TV e Get Screen Mode Status ID CheckSum o e Set Picture Size Header command DATA DATA ID Length CheckSum Screen Mode Screen Mode code to be set on TV Monitor Ack Header command DALA Ack Nak r CMD Vall Length Check ID Sum Screen Mode Same as above Nak DATA um ERR Error code that shows what occurred error is P Screen e Screen Size Control e Function Personal Computer recognizes the screen size of TV Monitor Introduction e Get Screen Size Status CheckSum a ME e Ack Header command DATA Ack Nak r CMD Vall Length Check ID Sum Size Screen Size Screen Size of TV Monitor Range 0 255 Unit Inch e Nak DATA Header command Leneih Ack Nak Vall
68. of the drawing program e Goto the Calibration tab e Click Start Calibration e Tap the four circles in sequence using the pen following the instructions displayed Connections e Click OK 3 5 Adding Keyboard Commands to Pens Make better use of Whiteboard by adding keyboard commands to pens 1 Go to Pen Setting gt Keyboard in the Samsung Interactive Whiteboard program Pan eg OOO aaa Connection DD Calibraton Keyboard Far 1 Pen Buton 3 mm Button 2 Bution Button 2 ma Balun JJllurn 2 Jullun 3 2 Select a button When the key assignment window appears press the keyboard key you want to assign The key will be assigned to the button Pen setting PAF x mmm Conrccticn Calibration Kovboard Pen 1 keyboard Registration Button 2 press kay to segistsr Bution 3 Bitoon 1 Bittor 2 Bi ton 4 3 6 Right click Function Button 1 Button 1 Button 1 Press Button 1 on the pen when the pen contacts the PDP screen The right click function of a mouse will be performed Connections ote e The right click function does not work unless the pen contacts the PDP screen 4 Afterimage Burn in Prevention ote e Afterimages can occur on this product due to the nature of PDP devices and the manufacturer shall not be liable for this issue e To prevent afterimages it is recommended that you observe the following instructions when using the product Instructions Ensure t
69. ol feature is available only for the displays whose power status is ON The Input source of MagicInfo works only on MagicInfo model k The Input source of TV works only on TV model o Maintenance Y Scroll 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Help Refresh Scroll Salety Screen or Bjo Ms E interwal Lima Apply Safety Screen 1 Scroll This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time 2 Pixel Shift This allows the screen to be moved finely at the specified time interval 3 Safety Screen The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time The Interval item is used to set the repetition cycle in hour units and the Time item is used to set the time when the Safety Screen function must be performed The Type item can be set to Scroll Pixel Bar Eraser All White or Pattern 4 Safety Screen2 This function is used to prevent afterimages from occurring There are five 5 types that you can select and control with this function For the Scroll type the Time item can be set to 1 2 3 4 or 5 For the Bar and Eraser types it can be set to 10 20 30 40 or 50 For the All White
70. om 7799 UZBEKISTAN 8 10 800 500 55 500 http www samsung com KYRGYZSTAN 00 800 500 55 500 http www samsung com TADJIKISTAN 8 10 800 500 55 500 http www samsung com UKRAINE 0 800 502 000 http www samsung com ua http www samsung com ua ru BELARUS 810 800 500 55 500 MOLDOVA 00 800 500 55 500 Asia Pacific AUSTRALIA 1300 362 603 http www samsung com NEW ZEALAND 0800 SAMSUNG 0800 726 http www samsung com 786 CHINA 400 810 5858 http www samsung com HONG KONG 852 3698 4698 http www samsung com hk http www samsung com hk en INDIA 3030 8282 http www samsung com 1800 3000 8282 INDONESIA 0800 112 8888 http www samsung com 021 5699 7777 JAPAN 0120 327 527 http www samsung com MALAYSIA 1800 88 9999 http www samsung com PHILIPPINES 1 800 10 SAMSUNG http www samsung com 726 7864 1 800 3 SAMSUNG 726 7864 1 800 8 SAMSUNG 726 7864 02 5805777 SINGAPORE 1800 SAMSUNG 726 7864 http www samsung com THAILAND 1800 29 3232 http www samsung com 02 689 3232 TAIWAN 0800 329 999 http www samsung com VIETNAM 1 800 588 889 http www samsung com Middle East IRAN 021 8255 http www samsung com http www samservice com Terms OMAN KUWAIT BAHRAIN EGYPT JORDAN MOROCCO SAUDI ARABIA U A E NIGERIA SOUTH AFRICA Dot Pitch Vertical Frequency Horizontal Frequency Interlace and Non Interlace Methods Plug amp Play Resolution Appendix Middle East 800 SAMSUNG 726 7864 183 225
71. onnect the HDMI IN port on the PDP Display to the HDMI port on the PC using the HDMI cable Note When the HDMI cable to the PC ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted DD using the BNC Analog connector on the video card e Connect the BNC COMPONENT IN port on the monitor to the BNC port on the PC using the BNC to BNC cable Connections Connect the audio cable for your PDP Display to the audio port on the back of the PDP Display Connect the power cord for your PDP Display to the power port on the back of the PDP Display Note e Turn on both your computer and the PDP Display e Contact a local SAMSUNG Electronics Service Center to buy optional items Using Whiteboard P64FT Model Only Note e Whiteboard does not support MagicInfo mode e A stylus pen may be subject to electromagnetic interference e This wireless device is subject to electromagnetic interference Do not use this device for a purpose that may affect personal safety 1 Connecting to a PC To use Whiteboard the product should first be connected to a PC Refer to Connecting a Computer for details about how to connect the product to a PC Connections 6 2 2 Components and Their Functions 2 1 Stylus pen No Functions 1 Enables the stylus pen when the sensor on it is pressed 2 Receives IR signals fro
72. or Temp ee OOK 4b Adjust Color Temp is a measure of the warmth of the image colors Note This function is only enabled if the Color Tone is set to Off Image Lock Lid Image Lock is used to fine tune and get the best image by removing noise that creates unstable images with jitters and shakiness If satisfactory results are not obtained using the Fine adjustment use the Coarse adjustment and then use Fine again Note Available in PC mode only Adjusting the PDP Display Coarse Removes noise such as vertical stripes Coarse adjustment may move the screen image area You may relocate it to the center using the horizontal control menu Fine Removes noise such as horizontal stripes If the noise persists even after Fine tuning repeat it after adjusting the frequency clock speed Position 1 H Position H Position Adjusts the screen location horizontally 2 V Position V Po sition Adjusts the screen location vertically Auto Adjustment Li Auto Adjustment 30 The values of Fine Coarse Position are adjusted automatically By changing the resolution in the control panel the auto function is performed Note Enabled in PC or BNC mode only Signal Balance Li Note e Enabled in PC or BNC mode only e This is used to make up for the weak RGB signal transmitted by a long signal cable Signal Balance Move Enter Retum Adjusting the PDP Display Selects either On or Off with th
73. ou can register holidays e Delete Selected Delete the selected holidays You can delete selected holidays Note e Only enabled when registered holidays are selected e More than one holiday can be selected and deleted e Delete All Delete all holidays min T You can delete all the registered holidays Menu TransparencyL2 8 Meum i Low Change the transparency of the background of the OSD 1 High 2 Medium 3 Low 4 Opaque Adjusting the PDP Display Safety Lock Change PIN Enter PIN BoUdd The password can be changed The preset password for the PDP Display is 0000 Note e Ifyou forgot your password press the remote buttons INFO EXIT MUTE to reset the password to 0000 Lock Enter PIN s000 0 9 Adjust Enter This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings Energy Saving This feature adjusts the power consumption of the unit in order to save energy 1 Off 2 On Note If Energy Saving mode is Off you can obtain the maximum display brightness Adjusting the PDP Display HDMI Black Level When a DVD or set top box is connected to your Product via HDMI it may cause a degradation in the screen quality such as an increase in the black level a low contrast or discoloration etc depending on the external device connected In this case adjust the screen quality
74. output terminal of a digital output device to the HDMI IN terminal of the PDP Display using a DVI to HDMI cable Connections 2 Connect the red and white jacks of an RCA to stereo for PC cable to the same colored audio output terminals of the digital output device and connect the opposite jack to the DVI RGB AUDIO IN terminal of the PDP Display 3 Select HDMI using the SOURCE button on the front of the PDP Display or on the remote control Connecting a DVD Player 1 Connect a set of audio cables between the AV COMPONENT AUDIO IN R AUDIO L on the PDP Display and the AUDIO OUT jacks on the DVD player 2 Connect a Component cable between the BNC COMPONENT IN R Pp G Y B Pg port on the PDP Display and the Pp Y Pp jacks on the DVD player Note e Select Component for the connection to a DVD player using the SOURCE button on the front of the PDP Display or on the remote control e Then start the DVD Player with a DVD disc inserted e A component cable is optional e Foran explanation of Component video consult your DVD manual Connections Connecting a DTV Set Top Cable Satellite Box 1 Connect a Component cable between the BNC COMPONENT IN R Pp G Y B P5 port on the PDP Display and the Pp Y Pp jacks on the Set Top Box 2 Connect a set of audio cables between the AV COMPONENT AUDIO IN R AUDIO L on the PDP Display and the AUDIO OUT jacks on the Set Top Box Note e Select Component for
75. reen L Ls The Safety Screen function is used to prevent afterimages that may appear when a still picture 1s displayed on the screen over a long time e The Safety Screen function scrolls the screen for the specified period of time e This function is not available when the power is turned off Pixel Shift Pixel Shift To prevent after images on the screen you can use this function so that every minute pixels on the PDP are moved in horizontal or vertical direction 1 Off 2 On Horizontal Dot Sets how many pixels the screen moves horizontally Five adjustment levels 0 1 2 3 and 4 Vertical Line Sets how many pixels the screen moves vertically Adjusting the PDP Display Time Timer Timer Mode Five adjustment levels 0 1 2 3 and 4 Set the time interval for performing the horizontal or vertical movement respectively You can set the timer for Screen Burn Protection If you start the operation to erase any residual image the operation will be performed for the set period of time and then automatically finish l 2 off On Bar E Eraser All White You can change the Safety Screen Type l PA Scroll Bar Eraser All White Pattern Period Time Scroll Bar Adjusting the PDP Display Hour Adjust Enter Return Use this function to set the execution period for each mode set in the timer Within t
76. roduct in portrait mode rotate it clockwise so that the LED indicator is at the bottom Ventilation requirement 1 Vertical wall mount condition lt Side view gt gt A min 40 mm B Ambient temperature Measuring point lt 35 C e When installing the product onto a vertical wall be sure there is a 40 mm space or more behind the product for ventilation as shown above and maintain the ambient temperature at 35 C or lower Note A Samsung Electronics service center can provide details Introduction 2 Embedded Mount guide lt Side view gt lt Top view gt D ty Vs min 40 mm min 70 mm min 50 mm min 50 mm Ambient temperature Measuring point lt 35 C Ws 7 o a W gt e When embedding the product in a wall be sure there is some space behind the product for venti lation as shown above and maintain the ambient temperature at 35 C or lower Note A Samsung Electronics service center can provide details 3 Floor mount guide lt Side view gt IS a sane A min 50 mm B Ambient temperature Measuring point lt 20 C e When embedding the product in the floor be sure there is a 50 mm space or more behind the product for ventilation as shown above and maintain the ambient temperature at 20 C or lower Note A Samsung Electronics service center can provide details Introduction Mechanical Layout E 1503 5 1413 0 55 2 4 6 40 4 r o
77. s from other types of waste and recycle them through your local free battery return system Note The rechargeable battery incorporated in this product is not user replaceable For information on its replacement please contact your service provider Authority Information in this document is subject to change without notice 2011 Samsung Electronics Co Ltd All rights reserved Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co Ltd is strictly forbidden Appendix Samsung Electronics Co Ltd shall not be liable for errors contained herein or for incidental or con sequential damages in connection with the furnishing performance or use of this material Samsung is the registered trademark of Samsung Electronics Co Ltd Microsoft Windows and Win dows NT are registered trademarks of Microsoft Corporation VESA DPM and DDC are registered trademarks of Video Electronics Standard Association the ENERGY STAR name and logo are reg istered trademarks of the U S Environmental Protection Agency EPA All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners S rS TruSurround XT SRS and the symbol are trademarks of SRS Labs Inc TruSurround XT technology is incorporated under license from SRS Labs TruSurround XT Inc
78. s in use e Set the Monitor to power off with the PC Display Properties Power Scheme e Use a Screen saver if possible Screen saver in one color or a moving image is recom mended a Change the Color Information periodically Type 1 FLIGHT FLIGHT O2348 OZ2348 UA102 UA102 Note Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes e Avoid using a combination of characters and background color with large difference in luminance Avoid using Grey colors which can cause Image retention easily Avoid Colors with big difference in luminance Black amp White Grey FLIGHT TIME Change the characters color periodically Information e Use Bright colors with little difference in luminance Cycle Change the characters color and background color every 30 minutes FLIGHT TIME FLIGHT FLIGHT TIME O2Z3468 FLIGHT TIME l FLIGHT TIME 0348 20 30 42 02348 20 30 Step1 Step3 e All area display Moving image together with Logo periodically Cycle Display moving image together with Logo for 60 seconds after 4 hours in use e The best way to protect your monitor from Image retention is to turn Power off or set your PC or System to operate a Screen Saver program when you are not using it Also Warranty service will be limited based on instruction guide D Apply the Screen Scroll function on Product e Apply the Screen Scroll fun
79. stalled when Source is set to MagicInfo in On Time mode PIP Size 1 Click PIP of the main icons and the PIP control screen appears Selects displays you want to adjust using the Select button or checkboxes Multiple Display Lontrol File Remote Control Safety Lock Port Selection Lamp Control Options Help o jo z mi All select Clear Idle Refresh CSL PIP Se PIP Source O PIP Size el oo Double 1 Av U AE a errr All Inputs Ye Info Grid shows some basic information necessary to PIP Size Control 1 PIP Size Shows the current PIP Size of the display in use 2 OFF Turns off the PIP of the selected display 3 Large Turns on the PIP of the selected display and changes the size to Large 4 Small Turns on the PIP of the selected display and changes the size to Small 5 Double 1 Turns on the PIP of the selected display and changes the size to Double 1 6 Double 2 Turns on the PIP of the selected display and changes the size to Double 2 7 Double 3 Picture By Picture Turns on the PBP of the selected display and changes the size to Double 3 k The Input source of MagicInfo works only on MagicInfo model The Input source of TV works only on TV model k PIP Size can be controlled with turning on the PDP Display power NG PIP PIP Source 1 Click PIP of the main icons and the PIP control screen appears Multiple Display Control File Remote Control Safety Lock Port Sel
80. the connection to a DTV Set Top Box using the SOURCE button on the front of the PDP Display or on the remote control e Foran explanation of Component video see your Set Top Box owner s manual Connecting to an Audio System 1 Connect a set of audio cables between the AUX L R jacks on the AUDIO SYSTEM and AUDIO OUT on PDP Display Using the Software Installing Whiteboard P64FT Model Only IR 2 10 First insert the Whiteboard installation CD into the CD ROM drive Double click Whiteboard exe Click Next in the displayed installation wizard screen When the License Agreement window appears select I accept the terms of the license agreement and click Next Select PC Mode and click Next in the displayed Setup Type window Select PDP Monitor and click Next Click Install in the displayed Ready to Install the Program window A window showing the installation progress will appear Click Finish in the displayed InstallShield Wizard Complete window After the installation the Samsung Interactive Whiteboard shortcut icon will be created on the desktop MDC Multiple Display Control Installation LA MDC Insert the installation CD into the CD ROM drive Click the Serial MDC installation program Note If the screen for installing the software does not appear install it using the Serial MDC execution file in the MDC folder of the CD ROM If the installation wizard screen does app
81. tings Control screen appears 1 2 3 4 5 6 7 8 T Multiple Display Control File Remote Control Safety Lock Port Selection Basic information required to adjust the Picture is displayed in the main menu Settings for the selected monitor will be displayed if one of the connected monitors is selected and the default settings will be displayed if all monitors are selected by clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode Picture Lamp Control Options Help Refresh Contrast 100 Brightness Sharpness lint Color Tone Available only for TV AV S Video Component HDMI1 HDMI2 DTV Contrast Adjusts Contrast of the selected display Brightness Adjusts Brightness of the selected display Sharpness Adjusts Sharpness of the selected display Color Adjusts Color of the selected display Tint Adjusts Tint of the selected display Available only for NT Color Tone Adjusts the Color Tone for the selected display Color Temp Adjusts the Color Temp for the selected display 9 Brightness Sensor Adjusts the Brightness Sensor for the selected display 10 Dynamic Contrast Adjusts the Dynamic Contrast for the selected display HDMI2 may not be supported depending on the product Brightness Sensor may not be supported depending on the product k The Input source of MagicInfo works on
82. uct surface and peel off the indication labels on the product L Since the product housing is easily scratched make sure to use the specified cloth only LI When cleaning the product do not spray water directly onto the main body of the product e Ensure that water does not enter the product and that it is not wet e Otherwise this may result in electric shock fire or a malfunction LJ The product is a high voltage product Do not disassemble repair or modify the product yourself e Otherwise this may result in electric shock or fire e Ifthe product needs to be repaired contact a Service Center L If there is a strange smell or a strange sound or smoke is coming from the product disconnect the power plug immediately and contact a Service Center e Otherwise this may result in electric shock or fire L Do not place this product in a location exposed to moisture dust smoke water or in a car e Otherwise this may result in electric shock or fire L When you drop the product or the case is broken turn the power off and disconnect the power cord Contact a Service Center e Otherwise this may result in electric shock or fire L If thunder or lightning is occurring do not touch the power cord or antenna cable e Otherwise this may result in electric shock or fire L Do not try to move the monitor by pulling only the wire or the signal cable e Otherwise it may fall and result in electric shock damag
83. um value for Horizontal is 6 if Vertical is set to 15 while the maximum value for Vertical is 6 if Horizontal is set to 15 4 Viewing Screen Splits You can view and change the layout of screens using the Screen Divider settings The range of the Screen Divider setting may differ depending on the model You may not operate this function in MagicInfo The Input source of TV works only on TV model k The Maintenance Control function is available only for the displays where the power status is ON Troubleshooting The display you wish to control does not appear on the Power Control Info Grid Check the connection of RS232C Check if it is properly connected to the Com1 port Check the displays to see if any of the other displays connected have the same ID If more than one displays have the same ID those displays are not properly detected by the program due to data conflict For monitors that support a Set ID between 0 to 99 you have to set the Set ID to a value between 0 and 99 Note Check if the Set ID of the monitor is a value between 0 and 99 set the value using the Display menu The display you wish to control does not appear on the other Control Info Grids Check to see if the display power is ON You can check this in Power Control Info Grid Check if you can change the input source of the display The dialogue box appears repeatedly Check to see if the display you wish to control is selected
84. use a damaged power cord or plug or a damaged or loose power outlet e Otherwise this may result in electric shock or fire L Do not touch the power plug with wet hands when removing or plug ging the plug into the outlet e Otherwise this may result in electric shock J Make sure to connect the power cord to a grounded power outlet e Otherwise it may result in electric shock or personal injury J Ensure that the power plug is plugged into the power outlet firmly and correctly e Otherwise this may result in fire Installation Safety Instructions L Do not forcefully bend or pull the power plug and do not place any heavy material on it e Otherwise this may result in fire L Do not connect multiple appliances to the same power outlet e Otherwise this may cause fire due to overheating L Do not disconnect the power cord while using the product e Otherwise this may result in damage to the product due to electric shock J To disconnect the apparatus from the mains the plug must be pulled out from the mains socket therefore the mains plug shall be readily op erable e Otherwise this may cause electric shock or fire J Use only the power cord provided by our company Do not use the provided power cord of another product e Otherwise this may result in fire or electric shock Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust high or low t
85. uter is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen may go blank while the power LED is on Refer to the video card manual and adjusts the screen as follows Display Mode Horizontal Vertical Fre Pixel Clock Sync Polarity Frequency quency Hz MHz H V kHz IBM 640 x 350 31 469 70 086 25 175 IBM 720 x 400 31 469 70 087 28 322 IBM 640 x 480 31 469 59 940 25 175 MAC 640 x 480 35 000 66 667 30 240 MAC 832 x 624 49 726 74 551 57 284 MAC 1152 x 870 68 681 75 062 100 000 VESA 640 x 480 37 861 72 809 31 500 VESA 640 x 480 37 500 75 000 31 500 VESA 800 x 600 35 156 56 250 36 000 TF VESA 800 x 600 37 879 60 317 40 000 TIF VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 46 875 75 000 49 500 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 DT VESA 1280 x 768 47 776 59 870 79 500 VESA 1280 x 960 60 000 60 000 108 000 ay VESA 1280 x 1024 63 981 60 020 108 000 op ial VESA 1280 x 1024 79 976 75 025 135 000 VESA 1360 x 768 47 712 60 015 85 500 HF VESA 1600 x 1200 75 000 60 000 162 000 FIF VESA 1920 x 1080 67 500 60 000 148 500 Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and th
86. y clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode 1 Audio Controls audio settings for all input sources 2 Bass Adjusts Bass of the selected display 3 Treble Adjusts Treble of the selected display 4 Balance Adjusts Balance of the selected display 5 SRS TS XT SRS TS XT Sound ON OFF of the selected display 6 Sound Select Select either Main or Sub when PIP is On The Input source of MagicInfo works only on MagicInfo model The Input source of TV works only on TV model This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed lm Settings a Image Lock 1 Click Settings of the main icons and the Settings Control screen appears SS Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Refresh Auto Adjustment Info Grid shows some basic information necessary to Settings Control 1 Image Lock Available only for PC BNC 2 Coarse Adjusts Coarse of the selected display 3 Fine Adjusts Fine of the selected display 4 Position Adjusts Position of the selected display 5 Auto Adjustment Self Adjust to the incoming PC signal The Input source of MagicInfo works only on MagicInfo model The Input source of TV works only on TV model Settings Control is available only for the displays for
87. z when using the maximum resolution 5 Ifyou have problems in installing the Adaptor video driver boot the computer in Safe Mode remove the Display Adaptor in the Control Panel gt System gt Device Administrator and then reboot the computer to reinstall the Adaptor video driver Check List Note e The following table lists possible problems and their solutions Before calling for assistance check the information in this section to see if you can remedy any problems for yourself If you do need assistance please call the phone number on the Information section or contact your dealer Problems related to the Installation PC Mode A note Problems related to the PDP Display installation and their solutions are listed Q The PDP Display screen flickers A Check if the signal cable between the computer and the PDP Display is securely connected Troubleshooting Refer to Connecting a Computer Problems related to the Screen Note Problems related to the PDP Display screen and their solutions are listed Q The screen is blank and the power indicator is off A Ensure that the power cord is firmly connected and the PDP Display is on Refer to the Connecting a Computer Check Signal Cable message Ensure that the signal cable 1s firmly connected to the PC or video sources Refer to the Connecting a Computer Ensure that the PC or video sources are turned on Not Optimum Mode message Check the maximum

User Manual - Howard Computers

Contents

Download Pdf Manuals

Related Search

Related Contents