Lojer.com Userdata Lojer User Manuals Healthcare R8009
Contents
1. f EN De Sams LS Bluetooth Lojer SCANDIA SC330 Operating Table User manual R8009 17 05 2012 Table of Contents 1 Lojer Scandia SC330 Operating Table cs sivssscdescesesisarecasissvesasiesenotsanceusasampvacssioisatiieneaccics 4 2 Dem ADIE DANS garapan e cet os cee en sec ctege spcnseesunceaseyeceeseeesieeeeacae 4 5 2 TN 5 2 3 Bluetooth hand control mnrrnvrrvrrvrrsrrsrrsrrsrrsersersrrsrverververserserserserserserserserseversen 7 NNN 8 AAN T e A E E E 8 4 BENENE eee ee ee eee ce eee eee 9 ER ROCA OU EEE EE SE 10 53 Hand COTATI 0 ges 10 JR NE 10 PA NN 11 5 2 HEDIN SMT UNNE SN vn 11 ON 12 TV 12 PN NNN 12 DENN 13 PANNE NN 13 S0 1116 ae TO Se CHOI EEE EE EE EEE REE 13 NNN 13 5 10 Trendelenburg and anti Trendelenburg rrsrsvnnrsnnvnrsennsevnsvnsevnsvnnsvnsvnsvnnsvesvresnee 13 5 11 2 FN 14 NN 14 5 13 Moving the operating G 0 REE EE EE 14 5 13 1 Locking the direction with the directional wheel rrssnsvnnvnnsvrsvnnvnnnren 15 5 13 2 Driving forward and backward rsrnsnnonnvnnvnvrnrsvesersernsvnvnnsvnsvesvnsrsernvvsvrsvrene 15 5 14 Using the foot switch accessory rnrnrrvnnvnvnvnnnvrnenvnnnnnnnsnrnennsvrnsvnnennsnvnsnenenesvnnsnee 16 PROMISING Me pcad Se CUON erana SA T E 17 6 1 Angle of inclination adjustment for head section s ssssseesseereerrseerrserresereesereesesees 18 6 2 Vertical adjustment of head section rrsnnvnrnnrnnnnvnrnnvnnrnnnn2. Copyright O Lojer Oy 2012 version 1 11 15 Technical data Dimensions and weights Overall length Width of table top Width over accessory rails Weight of the operating table Safe working load SWL in orientation Safe working load SWL in orientation Adjustment ranges Height without pads Trendelenburg Anti Trendelenburg Lateral tilt right left Back section up down Head section Leg section up down Longitudinal slide optional Speed of Driving wheel unit option Electrical data Main power supply EU Maximum current consumption Protection system Protection type Protection class Copyright O Lojer Oy 2012 version 1 11 2070 mm 550 mm 605 mm 260 kg 280 350 kg 250 kg 650 1010 mm 30 30 17 117 70 35 26 58 can be raised 135 mm 90 90 300 mm Max 0 7 0 8 m s full load 230 V 50 Hz 1 5 A x 230 V IP 24 B I Internal power supply main batteries 2 x 12VDC connected in series total 24VDC 20 Ah Operating rate 2 5 min 10 min Ambient conditions for transport and storage Temperature transport 10 C to 40 C Temperature storage 10 C to 40 C Relative air humidity 30 to 75 Air pressure 700 hPa to 1060 hPa Ambient conditions for operation Temperature 10 C to 40 C Relative air humidity 30 to 75 Air pressure 700 hPa to 1060 hPa 15 1 Identification plate The identification is located ins
3. 16 Warranty Thank you for purchasing this quality product from Lojer Our products are developed to meet high standards in both quality and technology To further ensure quality we grant you the final customer a warranty on our products in accordance with the following conditions The Lojer product is warranted for the period of twenty four 24 months from the original date of purchase against defective materials and workmanship Batteries and mattresses have twelve 12 month warranty In the event that warranty service is required you should return the product to the dealer from whom it was purchased In case of difficulty details of the local dealers are available at www lojer com You may also contact the service center in Finland email serviceQlojer com International warranty conditions 1 The warranty is only valid if when warranty service is required the warranty demand is presented with the original invoice or sales slip or confirmation and the serial number on the product has not been defaced 2 Lojer s obligations are limited to the repair or at its discretion replacement of the product or the defective part For this the customer is responsible for the dispatch and insurance of the product The transport and insurance costs shall be borne by the customer Lojer shall assume the costs for the materials spare parts and the labor costs as required as well as the return postage to the sender 3 In case of wa
4. 5 2 LED lights and audible signals The battery indicator LEDs are located at the bottom of the hand control beside the ON StandBy button see Figure 3 Hand control Table 7 Battery indicator LFDs gn eee Battery has sufficient charge for use Slow flashing Dropped battery capacity sufficient to carry out the a operation Continuous Battery capacity below critical level io the battery immediately The following indicators relate to the function buttons of the hand control Table 2 Function button LEDs and audible signals Changing green yellow LEDs The table is being locked unlocked Please lock function wait until flashing stops and either of the LEDs is lit continuously Blue LED Bluetooth The wireless connection between the hand control and the table is established Copyright Lojer Oy 2012 version 1 11 Yellow Unlock LED is Either the directional wheel or driving wheel is continuously lit and green activated both options Lock LED flashes every two seconds All three power indicator LEDs Internal problem contact service for are flashing Repeating beep troubleshooting sound during movements Short beep Indicates that you should pay attention with the table movements or the adjustment function has reached the endpoint for example the leg section has reached the max angle or table is locked unlocked Double beep Safety stop of all movements Communication problem between hand co
5. turn the standby switch to the ON position NOTE Turn the standby switch to StandBy during cleaning maintenance or in case of emergency 3 Connect the main supply cable to the socket in the main connection panel and charge the operating table batteries for 10 20 hours before using the table 4 Connect the spiral cable to the grey hand control and to the socket in the column of the operating table figure 6 Ensure that the connector is attached in the right way pins match the holes and then secure into position by tightening the nut Similarly connect the blue auxilary hand control to the cable socket in the connection panel see figure 4 Copyright Lojer Oy 2012 version 1 11 Figure 6 Socket for the hand control cable is located under the center section 5 Test the operating table functions with the hand control 6 Check that all castors run and freely and that they rotate freely allowing movement of the table in any direction 7 Test that the accessories of the table work correctly For instructions on how to install and use the accessories refer to the manufacturers documentation Make sure that they do not endanger the safety of the operating table 4 1 Precautions IMPORTANT Always immobilize the operating table by pressing the Lock button before using the adjustment functions Make sure that there is enough room around below and above the IMPORTANT operating table to complete all function
6. control see chapter 2 3 Sliding top function see chapter 5 12 Directional wheel see chapter 5 13 Driving wheel unit see chapter 5 13 NOTE The options are marked with in this manual 2 2 Hand control The operating table movements can be controlled by either of the two hand controls The standard hand control grey covers is used with a cable connection It is connected to the socket in the column of the operating table The auxiliary hand control grey covers can be used with a cable connection or wirelessly if the table is equipped with optional Bluetooth hand control blue covers Both hand controls have the same functions and symbols They operate in parallel for example when pressing a button in one hand control the corresponding LED indicator illuminates in the other hand control However you can only operate only one hand control at a time It is not possible to select functions from both hand controls simultaneously Copyright Lojer Oy 2012 version 1 11 B Both hand controls revert into power saving mode if not used for 1 240 min adjustable time with service software 1 Power ON StandBy 2 Battery full green LED 3 Charging batteries line power ON yellow LED 4 Battery low red LED 5 Bluetooth wireless connection blue LED 6 Floor locks locked green LED 7 Floor locks unlocked yellow LED 8 Normal patient orientation 9 Reverse patient orientation 10 Slide forward optiona
7. wearing Replace mattress with damaged surface with new one immediately Do not storage mattresses in close distance with sharp edges and not leave them to high temperate The mattresses must not be exposed to ozone 13 Maintenance 13 1 Monthly tasks Carry out the following checks and maintenance tasks once a month Keep record of the checks and the results Check all functions and movements of the table top one by one by adjusting them to their end position and back Remove all sections Clean all dowels pins holes and latches Lubricate them with thin machine or instrument oil Check that sections lock properly Check that the castors run freely and turn 360 Check that the cables and plugs are intact and that the connections function correctly 13 2 Annual tasks The operating table should be serviced at least once a year by an authorized service person The annual maintenance is instructed in a separate maintenance manual 14 Troubleshooting None of the hand The cable of the standard Check the cable connections control functions hand control is not and that the cable is intact operate and no connected leds are visible The battery of the auxiliary Charge the battery by Bluetooth hand control is connecting the auxiliary hand empty control to the operating table with a cable In the meanwhile use the standard hand control Stand by switch of the Turn the switch ON table under the hatch is
8. Bluetooth hand control in the cable turn On StandBy to Standby and then back On Then wait for 5 seconds until you see LED signal Hand control is now ready for wireless use with the specific table To activate the Bluetooth wireless function first disconnect the cable from the handset then hold down the power ON button for a few seconds The blue LED starts to flash and is lit when the wireless function is activated Hand control turns off if the connection is not established in 8 seconds The operating range for the wireless connection is 5 10 meters in an open space Bluetooth hand control revert into power saving mode if not used for 30 minutes If the wireless Bluetooth connection between the hand set and table can t be established the hand set will power down You can reactivate it by pressing the Power button Figure 4 Auxiliary hand control in the main connection panel IMPORTANT When placing the hand control in the service hatch make sure the cable is not touching the controller buttons Copyright Lojer Oy 2012 version 1 11 3 Safety instructions IMPORTANT gt IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT DR b gt 3 1 Warning signs Ensure that Scandia SC330 operating table is not exposed to electromagnetic radiation exceeding applicable norms Portable and mobile RF communications equipment can affect the operating table Use anti
9. and anti Trendelenburg Incline the entire tabletop level towards the head end to the Trendelenburg position by pressing the Trendelenburg button and to the anti Trendelenburg position by pressing the Anti Trendelenburg button The maximum inclination to both positions is 30 Return the tabletop back to the horizontal position by pressing the Zero position button or Anti Trendelenburg button for Trendelenburg position and vice versa NOTE The Trendelenburg button inclines always the head end also when the orientation is reversed Copyright Lojer Oy 2012 version 1 11 5 11 Zero position To return the table back to its initial position press the Zero position button This function returns the slide of the table top lateral tilt trendelenburg and anti trendelenburg positions and the inclinations of the leg and back sections one by one to the initial position Foot and back sections and trendelenburg are driven in 15 steps The height is adjusted separately from the hand control You will hear an audible beep when the operating table has reached the zero position within 1 2 tolerance Each movement has an individual zero position function for lateral tilt trendelenburg back section and leg section When any of the movements reach the horizontal level the movement is stopped To continue the movements briefly release the button press it again and the function will allow further adjustment NOTE lf all section
10. anel or inner parts of the operating table Safe working load 280 350 kg on Do not use the operating table for transporting the patient if floor locks with sliding top out 200 kg the floor is uneven max floor angle is 2 degrees Safe working load on wheels 250 kg See user manual before exceeding load 280 kg Copyright O Lojer Oy 2012 version 1 11 1 Safe working load 350 kg only in pre defined configuration see 10 2 2 Safe working load 280 kg in normal position on floor locks 200 kg with sliding top out 3 Safe working load 250 kg in reverse position also with sliding top out 4 Safe working load 250 kg on wheels 5 The max load of accessories is 40 kg and load per one accessory rail max is 25 kg Figure 5 Maximum load Safe working load SWL is the maximum allowed load including IMPORTANT the patient mattresses and accessories Overloading may result in tipping of the table 4 Before first time use Use the operating table in temperature of 10 C to 40 C and IMPORTANT humidity of 30 to 75 Let the operating table rest in room temperature for six hours IMPORTANT before taking it into use Attach the potential equalization conductor to the socket in the operating table base 1 Open the main connection panel hatch and insert the fuse 20A to the socket located in the panel The fuse is supplied in a separate box together with the hand controls and cables 2 In the main connection panel
11. ardous materials are collected and later on sent to specialised recovery companies for recovery or disposal Dismantling The next step is the dismantling of components and systems in order to market them as used part or to use them as basis for remanufactured parts If economically viable materials like plastics are taken off for recycling purposes Shredder The pre treated hulks are delivered to a shredder which segregates them into pieces and sorts the output into various fractions for further recycling or recovery The segregated material fractions from the shredder are further processed with different technologies to obtain material fractions which can be used as valuable secondary raw material that reduces drastically the amount of remaining waste for landfill Copyright Lojer Oy 2012 version 1 11 15 4 Standards The Scandia Operating Table SC330 complies with the following standards IEC 60601 1 Medical electrical equipment General requirements for safety and essential performance IEC 60601 2 46 MEDICAL ELECTRICAL EQUIPMENT PARTICULAR REQUIREMENTS FOR THE SAFETY OF OPERATING TABLES IEC 60601 1 2 MEDICAL ELECTRICAL EQUIPMENT PART 1 2 GENERAL REQUIREMENTS FOR SAFETY COLLATERAL STANDARD ELECTROMAGNETIC COMPATIBILITY REQUIREMENTS AND TESTS LOJER SCANDIA SC330 is class product European Council Directive 93 42 EEC Class I Lojer Oy is an ISO9001 certified company with environmental management system
12. cates the battery is now full Disconnect the main cable 6 Close the main connection panel hatch IMPORTANT Batteries should be changed every 3 years or when charge discharge cycle drops below 6 8 hours 10 Table top configurations You can change the table top configuration according to your needs The configurations allowed are described in the following sections NOTE In the normal configuration without accessories the system prevents the most typical collisions of operating table parts provided there are no obstacles above or underneath the table top 10 1 Standard configurations Figure 15 Standard configuration head section on normal side Copyright O Lojer Oy 2012 version 1 11 O Figure 16 Reversed configuration head section on reverse side 10 2 Safe working load 350 kg Figure 17 Biggest possible load for the table head section on normal side IMPORTANT SWI 350 kg is possible only with the table top configuration 81S P 1 P 5 decribed in Figure 17 Head section is on normal side and the patient is centered over the column Table must be locked on floor locks betore moving patient on the table and sliding top must not be used Figure 18 Lithotomy configuration step 1 Copyright Lojer Oy 2012 version 1 11 p 10 4 Lithotomy configuration step 2 Figure 19 Lithotomy configuration step 2 10 5 Cardiovascular configuration oe ae a Poa Figure 20 Cardiovas
13. cular configuration 10 6 TUR Configuration Figure 21 Configuration for TUR with Extension Plate 60150 Copyright O Lojer Oy 2012 version 1 11 10 7 Prohibited configurations Using the table in following configurations increase the risk of table instability With the increased risk of accident or injury to the IMPORTANT patient and persons in the vicinity of the equipment these configurations are considered unstable and are therefore prohibited Figure 22 Prohibited configurations example 1 head section on reverse side Figure 23 Prohibited configurations example 2 head section on normal side 11 Limitations in movements The operating table system software controls certain functions and prevents movements beyond the range specified in the following table You cannot override the limits with the hand control In movements other than specified in the table and when using IMPORTANT the operating table with a non standard configuration make sure that the operating table parts do not collide with the floor walls or other obstacles Copyright Lojer Oy 2012 version 1 11 The first row specifies the normal minimum or maximum position of each function The following rows describe the minimum and maximum positions in special situations Table height Normal min height 920mm Min height when leg section inclination gt 65 downwards Trendelenburg Normal max inclination Max inc
14. emoving operating table sections 1 Oneach side raise the latch A until it reaches its upper position Hold it 2 Grasp the section to be removed with both hands and pull evenly in the longitudinal direction of the table top This task will be easier if the section is raised slightly Figure 13 Opening latches NOTE To ease of section removal best results are achieved by applying even and gentle pulling force in the longitudinal direction 9 Charging the battery It is recommended that you charge the battery daily after use In normal use the battery lasts approximately one week However charging of an empty battery can take ten to twenty hours depending on the battery voltage No person is not allowed to lie on the operating table during IMPORTANT charging Be careful not to let any liquid enter the main connection panel IMPORTANT 1 Immobilize the operating table by pressing the Lock button 2 Open the hatch of the main connection panel at the base of the operating table Copyright Lojer Oy 2012 version 1 11 f D Figure 14 Main connection panel 3 Take the main cable and insert the plug into the charging socket 4 Connect the other end of the main cable to the wall socket The green light in the main connection panel and the yellow LED in the hand control should illuminate to indicate battery charging 5 When the green LED above the battery symbol in the hand control illuminates This indi
15. ide the hatch of the main connection panel Ce i 0 Serial number 2008040911218 Operating voltage 24VDC Power nt POV Enclosure class P24 Electrical protection cl Safe working load 1280 250 ke E E Operating time rate 2 5 10 min Lojer Oy Tel 358 0 10 830 6700 Putajantie 42 FIN 38210 VAMMALA FINLAND Copyright Lojer Oy 2012 version 1 11 D 15 2 Symbols Y Potential equalization conductor Protection type B Attention consult accompanying document s C 3 The operating table complies with the demands in directive 93 42 EEC for medical equipment The crossed out wheeled bin symbol reminds you that in the EU all electrical and electronic products batteries and accumulators must be taken to separate collection at the end of their working life Do not dispose of these products as unsorted municipal waste 15 3 Recycling After Lojer Operating tables and their parts have fulfilled their use recycling is the next critical step in completing the life cycle The metal content is more than 90 of the total weight of the table which makes the table among the most recycled industrial products Recycling of the table must be done by a professional organization and it must never be disposed as unsorted municipal waste Pre Treatment and storage First of all the batteries are taken off Then the dismantler takes off all oils These environmentally haz
16. ing the foot switch 6 Adjusting the head section Figure 10 Head section Copyright Lojer Oy 2012 version 1 11 6 1 Angle of inclination adjustment for head section 1 Push the shackle A upwards 2 Set the head section to the desired inclination 3 Release the shackle to lock in place 6 2 Vertical adjustment of head section Turn the locking handle B anti clockwise to release the head plate Move the head plate up or down to the required angle Turn the handle B clockwise to lock in place oo SS Check the angle of inclination and adjust if necessary as described in Adjustment of angle of inclination e g Set the head plate parallel with the back section 7 Attaching operating table sections The sections are locked to each other with a simple locking mechanism 1 Takea firm grip of the section 2 Align the pins with the holes Figure 11 Attaching the table section 3 Insert the section by pushing evenly so that the pins engage at the same time 4 To lock the section in place snap the latches on both sides into place If visible red signs are visible the latch is not locked Figure 12 Latches Copyright Lojer Oy 2012 version 1 11 D 5 Check that the section is firmly attached by pulling it Open latches indicate that the sections are not fully engaged and IMPORTANT may release unintentionally during the operation patient safety risk Red marks must NOT be visible 8 R
17. l 11 Slide backward optional 12 Zero position initial position of the operating table 13 Lateral tilt patient s right 14 Lateral tilt patient s left 15 Table top up 16 Table top down 17 Incline leg section downwards 18 Incline leg section upwards 19 Incline back section downwards 20 Incline back section upwards 21 Anti Trendelenburg 22 Trendelenburg 23 Drive forward or Directional wheel activation optional 24 Drive backward or Directional wheel activation optional Figure 3 Hand controller Copyright Lojer Oy 2012 version 1 11 2 3 Bluetooth hand control The auxiliary Bluetooth hand control is located under the hatch in the main connection panel It is normally connected to the operating table with a cable Bluetooth hand control has a built in battery that is charged automatically when the auxiliary hand control is connected to the operating table with a cable either in the charging socket of the main connection panel Fig 2 or to the socket in the column of the operating table NOTE The battery of the Bluetooth hand controller can only be charged when the Standby switch is turned ON The yellow LED illuminates when charging is in progress see point 3 in Fig 3 The auxiliary hand controller is initially paired and only meant for use with the specific table and will not operate together with any other equipment To ensure this the table and hand controller are paired together attach
18. lination when lateral tilt gt 5 Max inclination when back section inclination 20 Anti Normal max inclination Trendelenburg Max inclination when lateral tilt gt 59 13 Max inclination when leg section inclination gt 55 downwards Disabled Leg section inclination 65 downwards Lateral tilt Normal max tilt ED Max tilt when Trendelenburg or anti Trendelenburg gt 20 Disabled Leg section inclination gt 65 downwards Leg section 907 Normal max inclination downwards Max inclination when table height lt 920 mm Sliding top Normal slide towards the standard head end Disabled Trendelenburg or anti Trendelenburg gt 13 Leg section inclination gt 1 downwards Copyright Lojer Oy 2012 version 1 11 12 Cleaning and disinfection Switch power switch to StandBy before cleaning and detach the IMPORTANT main power cable Do not use shower high pressure water guns or similar for IMPORTANT cleaning Under no circumstances should steam or extremely hot water be used to disinfect or clean the table Do not clean the operating table in room with high temperature IMPORTANT and air humidity It can cause malfunctions in the hydraulics system Do not let fluids in the main connection panel or inner parts of the ORAN operating table D t lvents for cleaning IMPORTANT o not use solvents for cleaning Dry all surfaces thoroughly after cleaning or disinfection IMPORTANT 12 1 Me
19. nformation from the type plate located in the column of the operating table The maintenance of the operating table and the list of spare parts are described in a separate maintenance manual 17 Contact information Manufacturer Lojer Oy Putajantie 42 P O Box 54 FI 38201 SASTAMALA FINLAND Tel 358 10 830 6700 Fax 358 10 830 6702 www lojer com Lojer Service Finland Tel 358 10 830 6750 Email service lojer com Copyright Lojer Oy 2012 version 1 11 QD
20. ng forward and backward NOTE The adjusting functions of the hand control except up down and trendelenburg will not work when the drive function is on NOTE The drive function does not work in wireless mode or if main power cable is attached for battery charging 1 Go stand at the head end of the operating table 2 If the operating table is in immobilized position press the Unlock button 3 Attach the hand control to the accessory rail on your right hand side see figure 7 4 Press shortly either of the arrows at the top of the hand control You ll hear a double beeb In a few seconds the driving wheel comes down and touches the floor Unlock LED is continuously lit and Lock LED flashes every two seconds when the wheel is activated Copyright Lojer Oy 2012 version 1 11 s 5 Press shortly the arrow pointing forward at the top of the hand control to drive the operating table away from you Press shortly the arrow pointing backward to drive the operating table to the opposite direction You will hear a double beep before the operating table starts to move The driving wheel has a so called soft start the operating table moves first slowly and then faster For adjusting the speed of the driving wheel contact the authorized service personnel Figure 7 Driving the operating table 6 To stop the operating table release the button The operating table slows down smoothly and stops To deactivate the drive func
21. ntrol and table CPU Contact service for troubleshooting 5 3 Lock To immobilize the operating table press the Lock button The operating table floor locks come down The green yellow LEDs in the Lock and Unlock buttons start to flash and you can hear and audible short beep When the green LED in the Lock button is lit continuously the operating table is completely immobilized NOTE Do not turn off power while immobilizing is in progress NOTE To ensure safety only table height adjustment and trendelenburg functions operate when the table is unlocked 5 4 Unlock By pressing the Unlock button in the hand control for 1 second the floor locks are disengaged and lift up The green yellow LEDs in the Lock and Unlock buttons start to flash and you can hear a short audible beep The operating table is now on the castors You can move the operating table when the yellow LED beside the Unlock button is lit continuously NOTE Do not turn off power while mobilizing is in progress 5 5 Patient orientation In the normal patient orientation the patient s head is positioned towards the longer end of the operating table base viewed side on and in the reverse patient orientation towards the shorter end of the operating table base The green LED indicates the orientation in the hand control on the right for normal and on the left for reverse patient orientation Copyright Lojer Oy 2012 version 1 11 You can change the
22. orientation into reverse by pressing and holding for 3 seconds the Reverse patient orientation button on the left To change the orientation into normal patient orientation press and hold for 3 seconds the Normal patient orientation button on the right The green LED is lit continuously when the orientation has been changed The table will remain in the selected orientation even after switching off power from the ON StandBy button NOTE For safety reasons the button must be pressed for 3 seconds to activate NOTE The hand control and buttons function the same way whichever patient orientation Normal or Reverse is selected 5 6 Height Adjust the height of the table top level by pressing Table up and Table down buttons 5 7 Incline back section Adjust the inclination of the entire back section by pressing the Incline back section downwards and Incline back section upwards buttons The maximum inclination upwards is 70 and downwards 30 5 8 Incline leg section Adjust the inclination of the entire leg section by pressing the Incline leg section upwards and Incline leg section downwards buttons The maximum inclination of the leg section both upwards and downwards is 90 5 9 Lateral tilt Tilt the entire table level to the right viewed from the head end by pressing the Tilt right button Tilt the table level to the left by pressing the Tilt left button The maximum tilt to both sides is 17 5 10 Trendelenburg
23. perating Table This document gives instructions on how to use the Scandia SC330 Operating Table with software version 3 0 or later The Scandia SC330 Operating Table is designed to be used for human surgery in operating rooms The battery operated operating table consists of reconfigurable table sections that can be adjusted according to what is required in an operation The operating table has various hydraulic adjustment functions for the entire table top as well as for back and leg sections The hydraulic functions are operated by either a cable connected or a wireless hand control For correct and safe use of the table read all instructions carefully IMPORTANT before starting to use the operating table Ensure that all operating persons are familiar with these instructions 2 Operating table parts op POE 1 Head section 2 40 cm section 3 25 cm section 4 Center section 5 6 Hand control 7 Locking latch 8 Accessory rail 9 Floor lock 10 Main connection panel 11 Potential equalization conductor 12 Connection for optional foot switch Figure 7 Scandia SC330 Operating Table Copyright Lojer Oy 2012 version 1 11 p Auxiliary hand control 1 2 Computer interface D connector 3 Charging indicator LED green 4 Standby switch Table On StandBy 5 Fuse 3 6 Charging socket Figure 2 Main connection panel 2 1 Options You can order the operating table with the following options Bluetooth hand
24. rranty repairs they must be carried out by Authorized Lojer Dealers No re imbursement will be made for repairs carried out by non Lojer representative and any such repair work and damage to the products caused by such repair work will not be covered by this warranty 4 This product is not considered to be defective in materials nor workmanship by reason that it requires adaptation in order to conform to national or local technical or safety standards in force in any country other than the one for which the product was originally designed and manufactured This warranty Copyright O Lojer Oy 2012 version 1 11 will not cover and no re imbursement will be made for such adaptation or any damage which may result 5 This warranty covers none of the following A Periodic check ups maintenance and repair or replacement of parts due to normal wear and tear such as upholsteries ropes or reduced capacity of accumulators B Cost relating to transport removal or installation of the product C Misuse including the failure to use this product for its normal purposes or incorrect installation D Damage caused by lightning water fire acts of god war public disturbances incorrect mains voltage or any other cause beyond the control of Lojer E Spillage of chemicals or liquid or use of any other hazardous or non instructed substances which may affect the product F Minor defects or deviations from the product specification
25. s especially when accessories are attached Hand control functions You can press only one button at a time If you press more than one button at the same time neither will work If you press a second button while one function is operating the first function will then be stopped Each movement has a software controlled limit You can stop any motion by releasing the function button or you can hold the button until it reaches the limit set for that function and the movement will stop automatically NOTE Even when the Power LED of the hand control is off the table uses a small amount of power This may lead to full discharge of the batteries after some weeks Copyright Lojer Oy 2012 version 1 11 f D 5 1 Power ON StandBy Press the ON StandBy button in the hand control to activate the operating table During start up phase three LEDs are flashing as a string and all functions are disabled Green LEDs illuminate beside the ON StandBy button as well as in the Lock and the Patient orientation buttons NOTE The system switches off power if you do not use any function for 1 240 minutes time adjustable Reactivate the operating table by pressing ON button in either of the hand controls Turn off power by pressing the ON StandBy button in the hand control Turning off power using the ON StandBy button stops all IMPORTANT movements of the table You can press it also in case you need to stop a function quickly
26. s that are immaterial or negligible as regards to the value or the functioning of the product The guarantee will become void ifa Lojer product is equipped or used with parts that have not been approved by Lojer for the product in question if someone other than a person authorised by Lojer has serviced repaired or otherwise modified the device and these measures have caused a fault in the product ifthe product is cleaned with cleaning agents other than those specified in the operating manual or if the product is put into direct contact with agents other than those specified in the manual ifthe regular maintenance has not been performed Proceeding in a warranty case The following information is an explanation of what you must do in the case of a warranty claim Should contrary to expectation your Lojer product be defective please contact your Lojer dealer first There our employees will help diagnose defects and malfunctions They are often capable of eliminating the malfunction over the phone Please always have the following information ready before calling the dealer or Lojer Service Your name address post code and a telephone number at which you can be reached the model designation the article code and the serial number of the product the date of purchase Copyright Lojer Oy 2012 version 1 11 abrief description of the problem possibly including photographs You will find the i
27. s are not straight and leveled after reaching the zero position the safety sensors of the operating table must be recalibrated Contact the authorized service personnel for recalibration 5 12 Slide Slide the operating table top in the direction of the standard head end by pressing the right arrow of the Slide button continuously until the table reaches the required position Similarly to slide the table top in the direction of the standard foot end press the left arrow The maximum slide movement is 300 mm IMPORTANT When using the slide the safe working load is 200 kg in normal orientation and 250 in reverse position NOTE For safety reasons some functions do not operate when using the slide function For details see Section 11 NOTE Limitations inmovements NOTE The direction of the slide function will not change in the Reverse Patient orientation The slide moves always towards the standard head end 5 13 Moving the operating table The operating table may be equipped with an optional directional wheel function or an optional motor operated driving wheel Both functions lock the direction of the operating table to ease transporting along corridors When on castors the safe working load for is 250 kg For maximum IMPORTANT stability the table must be lowered below 800mm before patient transfer Copyright O Lojer Oy 2012 version 1 11 D Do not use the operating table for transporting the patien
28. snnnnsnnnnsnnensnnnvsnnnnsnnnssnnnesene 18 7 Attaching operating table SectiOnS ssransnnnarnnnansnnanennnnnnnnnnnnnansnnnnennnnnnnnnnnnnanennnnennnenee 18 8 Removing Operating table sectlionsuuunaamumamsunagvmsmavsnidamsmansvansmninne 19 Copyright Lojer Oy 2012 version 1 11 re 19 10 EON 20 Vi Standard CONNEUTAUONS vvvv vvrjr4v4vrv74ev4v47vesvrvrervevvmnn 20 VENNINNEN 21 103 Lithotom CONTIG ULATION Step I esimesse ennn EEr EAE ara Enas 21 10 4 Lithotomy configuration step 2 sesesssseesessersessessessessessessessereesseseesseseessessessessesseseeee 22 10 5 Goose r res sen 22 VG ROT 22 VATN vrr44v4v44144747414444v n a ES Raser er iiaa 23 A GUMON INOVE MEN S asinn E 23 12 Cleaning and disinfection s ssseseessesssecosescecsseccecsecssecoecsesssssssecssessecsscosecsesosecsscssses 25 12 1 MENN 25 12 2 Operating table mattresses and straps rrsnrrnrrnnrnnrnrnnnnrnvnnnervrnsvnnvennrnsvesvesnvevvenvesn 25 gt MING 26 13 1 NOT EE SEERE 26 D2 ARU EEE E EN 26 WA PROUD IES INO OG Ne EEE E E 26 MS SCT A sears E E E 29 15 1 Ko ey a ahi Torco oy oa EE EE EE terror er arn 30 D 0010 GJERE tara tec teppei este SN EE se ieee 31 DD FM 31 ee E e ET 0 E N A reer Te enn A eee eer ere ee re A 32 GB NT 32 17 COMAC 0 og ENE cet ouseeseeene aes sete 34 For easy access The user manual should always be kept close to the operating table Copyright Lojer Oy 2012 version 1 11 1 Lojer Scandia SC330 O
29. static cushions to ensure discharge of static electric Use grounding cord during all functions to prevent possible electrostatic discharge Although mechanically possible do not use the operating table in other configurations than those illustrated in this document See Section 10 Table top configurations Check that the table sections are correctly locked in place before using the table See Section 7 Attaching operating table sections When not in use ensure that the hand control is secured safely to the head section of the table This will prevent it from getting caught between different sections or moving parts of the operating table as well as other equipment Make sure before using the adjustment functions that there are no body parts of the patient or personnel between different sections or moving parts of the operating table Pay extra attention to any table top movements downwards especially when the column in its lower position In case of a malfunction take the operating table immediately out of use and contact the authorized service personnel Pay attention to the following warning signs attached to the base of the operating table Warning Normal Orientation Read user manual carefully before use Install and tighten all accessories according to the instructions Max weight of accessories 40 kg max 25 kg on single side rail Do not let fluids come in contact with the main connection JE p
30. t if the IMPORTANT floor is uneven Max floor angle is 2 degrees NOTE For safety reasons the drive function and the directional wheel do not function in wireless mode Use always a hand control attached by cable Before moving the operating table 1 Besure that the patient is properly secured to the table 2 Center the patient over the main lift column of the operating table 3 Lower the table top below 800 mm height 4 Remove all cables from the table Check the floor for and remove objects that may interfere with moving the table such as power cords or table accessories 5 Have at least one person at each end of the table 5 13 1 Locking the direction with the directional wheel NOTE The driving wheel replaces the function of the direction lock castor NOTE The different table top functions will not work when the directional wheel is activated 1 Press either of the arrow buttons at the top of the hand control for few seconds to activate the directional wheel The Unlock LED is continuously lit and Lock LED flashes every two seconds when the wheel is activated The directional wheel comes down and you can move the table straight forward and backward manually When directional wheel is activated moving the table sideways is difficult and thus not recommended 2 To deactivate the direction locking press the Unlock button on the hand control or release the movement button for about 7 seconds 5 13 2 Drivi
31. tal and plastic surfaces Clean the metal and plastic surfaces and the hand controls with a damp cloth and weak alkaline cleaning fluid Use small brush for corners and other difficult spots Rinse with clean water and dry carefully after cleaning Use disinfectant e g 70 methylated spirit and follow the disinfectant manufacturer s instructions for use Let dry by evaporation in room temperature NOTE All surfaces must be dry before switching the operating table ON 12 2 Operating table mattresses and straps Remove the table top pads before cleaning Wash mattresses and straps carefully with warm water 50 and neutral pH7 detergent Rinse with clean water wipe them dry and leave to dry in room temperature Use small brush for corners and other difficult spots Spray a disinfectant 70 methylated spirit or 1000 5000 mg ltr solution of hypochlorite in water directly onto the pads Rinse with clean water Wipe clean with absorbent soft paper and let dry by evaporation in room temperature If necessary brush the Velcro bands the pads and the tabletop with a non metallic brush NOTE Do not let hypochlorite solution to come into contact with metallic parts Long term contact with mattresses may damage them NOTE If non Lojer pads are used refer to the table pad manufacturer s instructions on the use of disinfectants with table pads Copyright Lojer Oy 2012 version 1 11 zi Check mattresses regularly for damages and
32. tinues angle position sensors provide false values contact service immediately No negative implications Led turns off after using the table for a while Table is difficult to move sideways Some movements do not operate During movement table is stopped with double beep Directional wheel or drive motor is being activated One or several movements have reached the end position beeb sound or the table controller prevents the movement due to the risk of collision Sliding top is not in the home position and safety sensors are blocking some movements see conflict table ch apter 11 Safety stop due to communication failure Safety stop due to communication failure when using Bluetooth hand control Press table unlock button once to deactivate the motor Press 0 position button for few seconds to release the blocked functions Move sliding top to the home position and then move the other functions If the problem is repeated take table to service Check whether the aux hand control works perfectly If yes replace main hand control with aux hand control If the problem is repeated the spiral cable is most likely damaged Use Bluetooth closer to table and make sure there are no obstacles even staff between table and signal If the problem is repeated take table to the service For ordering spare parts contact Your local dealer or Lojer Service see 17 Contact Information
33. tion press the Unlock button or release the movement button for about 7 seconds NOTE The logic of the arrow buttons is reversed when attaching the hand control to the accessory rail of the head section on your left hand side NOTE If the power of the table battery falls below the critical level the red LED above the battery symbol illuminates in the hand control the system automatically stops the drive function and lifts the driving wheel up The castors of the operating table operate normally and you can move the table manually Recharge the table batteries immediately NOTE When using the drive function the table may also be stopped by pushing the Power ON StandBy button emergency stop 5 14 Using the foot switch accessory The foot switch is an accessory The footswitch functions include Trendelenburg and anti Trendelenburg Left and right lateral tilt Table up and down Copyright Lojer Oy 2012 version 1 11 16 1 Trendelenburg and anti Trendelenburg 2 Lateral tilt 3 Table up and down Figure 6 Footswitch The footswitch enables procedures where the surgeon is normally seated at the short end of the table It is possible to change the footswitch functions and the pedal positioning with Lojer maintenance software Contact service for changing the setup To connect the foot switch remove the connector cover and attach the footswitch connector to the socket at the leg end of the table Figure 9 Attach
34. turned StandBy Copyright Lojer Oy 2012 version 1 11 26 Bluetooth control cannot be turned on only leds flash briefly Foot pedal do not function The hand control is turned ON but only up down and trendelenburg do operate Drive motor does not function All power indication leds in hand control are flashing simultaneously Charging led yellow remains On even after power plug has been removed Copyright Lojer Oy 2012 version 1 11 zi The batteries of the operating table are empty The hand control has damaged The hand control battery is empty Cable is not connected properly Foot pedal functions have not been set up with maintenance software Table is unlocked Table is locked The power cable is attached to the table Table is locked and you hear beep sounds during table movements Battery voltage remains high after charging Connect the main cable to the charging socket and charge the batteries Contact service In the meanwhile use the other hand control Connect the cable turn Standby switch to ON and let the battery be charged for 1 2 hours Connect the cable as instructed Contact service to program the functions Press table locking button to enable the movements Press table unlocking button to enable the movements Disconnect the power cable Reset the alarm by setting main switch to Standby and back On If alarm still con
Download Pdf Manuals
Related Search