the user manual
Contents
1. The top of the flue must be 1200mm above the roofline Alternatively there must be a minimum distance of 3 meters from any higher section of roof viol lv Vv OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 6 3 INSTALLATION continuen 3 3 Protecting the floor Any combustible floor beneath a fireplace must have a floor protector that extends minimum 300mm at the front f installed directly on combustible material the floor protector must be made of a minimum 6mm thick cement sheet Non combustible finishes can be applied to the floor protector tiles steel sheet light concrete etc If the combustible floor is installed on concrete you can replace the combustible material with non combustible material laid directly onto the concrete FLOOR PROTECTOR LAID ON TIMBER FLOOR Insulative board 6mm non combustible finish Combustible floor eg timber X mad FLOOR PROTECTOR LAID ON JOIST Combustible floor eg timber Insulative board 6mm non combustible finish A Joist OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 7 3 INSTALLATION continuen FLOOR2. non combustible surfaces see 2 2 OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 4 3 INSTALLATION 3 1 Typical flue kit installation lt lt tek se Cowl Chinaman Hat 9 Outer Case 11 Outer Case RUBBER lt DEKTITE FLASHING 7 Active Flue 9 Outer Case tm 11 Outer Case gt NN R CEILING RING PP Ar 7 9 Flue gt NS Oy OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 5 3 INSTALLATION continuen 3 2 Installing the external flue 1 Place the connection piece inside the suspension bracket This will join the single skin flue below the bracket and the triple skin flue above the bracket which have different diameters 2 Ensure the triple skin flue is installed as per Australian standards see diagrams below PITCHED ROOF INSTALLATION The top of the flue must be 400mm higher than the highest point of the roof Alternatively there must be a minimum distance of 3 meters from any higher section of roof 240 cm gt 3m gt 40 cm eee ee 2 40 cm an a Y FLAT ROOF INSTALLATION LESS THAN 5 PITCH
3. PROTECTOR LAID ON CONCRETE Floor protector Combustible floor eg Timber Fee ee eh Non combustible finish oor eg timber eg tiles M HH A EE ee eee ae Concrete E E o c N lt 300mm lt 810mm OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 8 4 OPERATION 4 1 What you should burn Untreated air dried hardwood Split logs with a humidity content of less than 20 4 2 Do not burn Trash Painted plastic Coated or preservative treated wood Waste or black coal Inflammable liquids Fire gels e Moist wood with a residual humidity content of more than 20 this may cause soothing of the chimney IMPORTANT Misuse may lead to unhealthy and environmentally harmful emissions and will void any warranty or guarantee The maximum load capacity for the Pharos is 10kg of wood Burning only seasoned hardwood helps to protect the environment and lower emissions For details of a wood supplier in your area please call our office on 03 9416 0400 or email infoldoblica com au Do not use flammable liquids or aerosols to start or rekindle the fire Do not use flammable liquids or aerosols in
4. relevant building code or codes Any modification of the appliance that has not been approved in writing by the testing authority will be in breach of the approval granted for compliance with AS NZS 4013 o Once the flue has been installed and approved by a professional installer the flue must not be modified in any way OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 3 2 PRE INSTALLATION conrmueo MINIMUM CLEARANCE INTERNAL 2 1 Clearance from non combustible surfaces 2 3 Clearance from combustible surfaces eg masonry eg timber joist amp concrete 100mm minimum clearance is required from fully Clearances may be reduced with the application of non combustible surfaces heat shielding to walls in accordance to the Non Combustibl hala 2 Australian Building Code For information on heat shielding please contact our 6 office on 03 9416 0400 or email infoldoblica com au 3 vz s mn a Configuration 1 Parallel installation Combustible uugz9 2 2 Clearance from glass 625mm alqhsnquio 400mm minimum clearance is required from normal non combustible glass Glass frameless or aluminium frame 5 3 El Configuration 2 Corner installation 400mm 5 Combustible E a Z a V 3 o IMPORTANT v Frames must also be considered Timber window A frames must be treated as combustible surfaces 750mm see 2 3 Aluminium frames can be treated as
5. PHAR0S MODEL SPECIFICATIONS 1 TECHNICAL DATA 2 2 PRE INSTALLATION 3 3 INSTALLATION J 4 OPERATION 9 9 TESTING 10 Keep for future use INVICTA x FRE 1 TECHNICAL DATA WEIGHT AND DIMENSIONS Dimensions Firebox W531 x H1250 x D530mm Firebox weight 167kg Flue kit Standard 7 9 11 Nominal thermal output OKW Efficiency Australian Test 60 Emissions Australian Test 1 2g kg 7 9 FLUE OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 2 2 PRE INSTALLATION Congratulations on your purchase of the Pharos This appliance should be installed and checked by a qualified professional Ensure you have read the operation guidelines thoroughly prior to first use For any questions or concerns please contact Oblica on 039416 0400 The installation process is outlined below Determine position of firebox and flue carefully observing the clearances described within this section Install the external flue Install the internal flue and engage the firebox Ensure the floor has adequate protection CAUTION Using components or parts other than those provided by the manufacturer or modifying the specification of components may result in inferior or unsafe operation If such action is necessary consult the manufacturer in the first instance The appliance and flue system must be installed in accordance with AS NZS 2918 and the
6. the vicinity of the fireplace when operating e Do not store fuel within prescribed installation clearance distances The use of some types of preservative treated woods as a fuel can be hazardous OBLICA PHAROS INSTALLATION AND USER MANUAL PAGE 9 9 TESTING TEST REPORT NO HCMG 15 041 TESTING LABORATORY MANUFACTURER MODEL WORK REQUESTED ISSUE DATE INVESTIGATING OFFICER RESULTS CONCLUSION OBLICA PHAROS INSTALLATION AND USER MANUAL HRL Technology Invicta Pharos fireplace Assessment of appliance to AS NZS 4012 2014 for determination of Power Output and Efficiency and AS NZS 4013 2014 for Flue Gas Emission using hardwood fuel 23 07 2015 Steve Marland The Pharos solid fuel burning appliance produced an appliance particulate emissions factor of 1 2g kg and an average efficiency of 60 for all burn rates using hardwood that complies to AS NZS 4014 1 when tested according to joint AS NZS 4012 AS NZS 4013 2014 The Pharos solid fuel burning appliance complies with the requirement of a combined efficiency of not less than 55 and a particulate emissions factor of not greater than 2 5g kg of hardwood that complies to AS NZS 4014 1 in AS NZS 4013 2014 PAGE 10
Download Pdf Manuals
Related Search