Sensor BP使用手册
Contents
1. Illumination value 2 Movement Setting Threshold 2 value Upper threshold Movement Value Must Upper than Lower threshold Logic Setting Logic Value Respond mode of the brightness hone Threshold 1 value Lower threshold Threshold can be changed via bus disable Threshold behaviour with hysteresis Interval time of value cyclic send Base ls Factor 1 255 i Send Illumination Teleg on bus recovery Info Fig 4 2 Parameter window Illumination Setting 1 1 3 Sensor BP fold General Illumination Value 1 Illumination Setting Illumination value 1 Hluroination value 2 Movement Setting ale nace Movement Value logic 1 bit 0 1 Logic Setting Logic Value 4bit 0 15 If Luxe Lower value send mode Tbyte 0 255 Lus Curent Brightness value EA Lower Lus Lower threshold Upper Lux Upper threshold KER Attention Fig 4 3 Parameter window Illumination value 1 2 Parameter Threshold 1 value Lower threshold This parameter is used to set lower threshold Option 0 65535 Parameter Threshold 2 value Upper threshold Must Upper than Lower threshold This parameter is used to set upper threshold upper threshold must be greater than lower 9 threshold Option 0 65535 Parameter Respond mode of the brightness This parameter can be set how to respond the brightness value Option None Respond after read only Cyclical If selecting none2. power up the master will do with the formation according to their actual value If the value is the specified value the master will send the delay start value During the delay time the master does not receive the specified value again it will send the delay over value i e when the master s illumination movement or logic value has changed and the input value is no longer the specified value the delay time will be started if during the delay time the master does not still receive the specified value the master will send the delay over value If movement as a slave the movement over value will be slave input value after bus voltage recovery If illumination as a slave when the current illumination between lower and upper threshold and the threshold behavior with hysteresis the logic input is the value of lt lower otherwise it will be the same as the value of last status Parameter Master delay start when This parameter is used to set the master delay time when to start i e when the master receives the special value from a slave it will send the values of three different data type and the delay time will also be started Options Object slave value receive 0 Object slave value receive 1 If selecting Object slave value receive 0 when the object slave value receives the value 0 the master will send the values of three different data type and the delay time will also
3. Low gis Illumination send 1 bit Illumination send 1 bit 1 bit c Low mis Illumination send 4 bit Illumination send 4 bit 4 bit E ff Low Ejio Illumination send 1 byte Illumination send 1 byte 1 Byte C e p s Low Fig 5 1 Communication object illumination function Note C in Flag column in the below table means that the object has a normal link to the bus W means the object value can be modified via the bus R means the value of the object can be read via the bus T means that a telegram is transmitted when the object value has been modified U means that value response telegrams are interpreted as a write command the value of the object is updated Cyclical send lux value Cyclical send lux value This communication object will be visible with cyclical in the parameter Respond mode of the brightness which is used to send the current Lux value cyclically on the bus Read lux value Read lux value This communication object will be visible with respond after read only in the parameter Respond mode of the brightness which is used to read the current Lux value via the bus Change threshold lower upper Chang threshold Lower Upper The communication object is visible when the parameter Threshold can be changed via object is enabled it is used to modify the value of threshold and threshold 2 Values range 0 65535 8 9 10 Illumination send1bit 4bit
4. be started If the object slave value receives the value 0 again on delay time the delay time will be reset If selecting Object slave value receive 1 when the object slave value receives the value 1 the master will send the values of three different data type and the delay time will also be started If the object slave value receives the value 1 again on delay time the delay time 20 will be reset When the delay time is over the master will also send the values of three different data type Note If the master s own value as a salve input the master will processes the information in the device internal and do not need receive via the object slave value then trigger that the master send the values of three different data type and the delay time will also be started Parameter Master Delay time Base x Factor 1 255 This parameter is used to define the delay time which will be begun when the master receives the special value from a slave The delay time Basex Factor Base option 100ms Is Factor option 1 255 Parameter The master Delay start when receive specified value This parameter indicates when the master received the specified value the master delay start Parameter If the master receives the value again on delay time Delay time will be reset This parameter indicates if the master received the specified value again during delay tim
5. object If selecting disable it will be not changed Note The new sensitivity will be saved when bus power down Parameter Function of movement retrigger This parameter is used to set whether retrigger operation when sensor detects some object moving again or not Options Disable Enable If selecting enable when the sensor detects some object moving again on the delay time the delay time will be reset and the movement operation retrigger The delay time can be set in following parameter Delay time of movement Base x Factor Parameter Delay time of movement Base x Factor This parameter is used to define the delay time which will be begun when the sensor detects some object moving The delay time Basex Factor Base option 100ms Is Factor option 1 255 Parameter Interval time of value cyclic send Base x Factor 1 255 This parameter is used to set the interval time of two telegram values that are sent cyclically The objects of three data types can be sent The time Basex Factor Base option 100ms Is Factor option 1 255 Parameter If Movement start Movement over value send mode The two parameters are used to set the mode that the movement objects send the values when the movement start or over Options No send Send one time Send cyclically 14 If selecting no send the objects will be not sent any telegram to the bus if selecting send on
6. 3 Sensor BP fold General Logic Yalue Illumination Setting Illumination value 1 Illumination Value 2 Movement Setting Movement Value Logic Setting l Logic Value 4 bit 0 15 If logic result 0 value send mode Logic 1 bit 0 1 4 1 byte 0 255 Oo lt gt If logic result 1 value send mode Logic 1 bit 01 1 yt 4 bit 0 15 J 1 byte 0 255 p oo lt gt Fig 4 7 Parameter window Logic Value Parameter input1 logic 1bit of illumination value input2 logic 1bit of movement value This parameter indicates the logic value of input I is set by Ibit type of illumination value see chart 4 3 and the logic value of input 2 is set by 1bit type of movement value see chart 4 5 16 Parameter Input 0 of logic is This parameter is used to set whether enable input 0 in logic operations or not Options Disable Enable Parameter Object value of input 0 for logic after bus voltage recovery The parameter is visible when then enable is selected in the parameter input 0 of logic 18 It is used to set object value of input 0 for logic after bus voltage recovery 0 1 Object value of input 0 can be changed via object Input 0 of logic The object is visible when enable input 0 Note when the logic operation is disabled input 0 of value can t be changed Parameter The logic function type between input and input2 Th
7. Guangzhou Video Star Electronics Co Ltd K BUS Sensor BP User manual Ver 1 CSBP 02 00 1 Intelligent Installation Systems 6 c http www video star com cn Contents 1 2 3 4 Overview mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm m m mmm m m 3 Technical data mmmmmmmmmmmmmmmmmmmmmmmnmmmm mmm mmm 3 Dimension and induction schematic diagram 4 3 1 Dimension drawing 4 3 2 Induction schematic diagram 5 Project design and programming mmmmmmmmmmmmnmmmmmmmmmmmmmmmmmmmmmmmmm 5 4 1 Parameter window General 7 4 2 Parameter window Illumination Setting 8 4 3 Parameter window Movement Setting 12 4 4 Parameter window Logic Setting 15 4 5 Parameter window Master Setting 18 Description of communication obje
8. Ibyte Illumination send 1bit 4bit Ibyte 1bit 4bit Ibyte The communication objects are used to send illumination values of three different data types when the current brightness is less than the low threshold or is between lower and upper threshold or is greater than upper threshold The illumination values are set in the parameter logic 1bit 4bit Ibyte Table 5 1 Communication object table illumination function 22 5 2 Communication object Movement function N Name Object Function Description Group Addresses Length C R W T U Data Type Priority ET Change sensitivity Change sensitivity 1 Byte C Low Eji Movement send 1bit Movement send Ibit 1 bit C lt T Low Eiz Movement send 4bit Movement send 4bit 4 bit Ca of e Low E13 Movement send 1byte Movement send lbyte 1 Byte C Low Fig 5 2 Communication object movement function Change sensitivity Change sensitivity This communication object will be seen with enable in the parameter Sensitivity can be changed via bus which is used to change the sensitivity of the sensor movement detecting 11 12 13 Movement send Ibit Abit Ibyte Movement send 1bit 4bit Ibyte 1bit 4bit Ibyte The communication objects are used to send movement values of three different data types when the movement start or over The movement values are set in the parameter logic 1bit 4bit lbyte Table 5 2 Communication object table movement func
9. Movement Function Enable Movement Function 1 bit Cc Low mjs Enable Lux Function Enable Lux Function 1 bit CT Low Fig 5 5 Communication object disable enable illumination movement and logic function Enable Lux Function Enable Lux Function The object is used to disable enable lux function The lux function is disabled if the object receives a telegram 0 while it is enabled if the object receives a telegram 1 The lux function default to enable after bus voltage recovery Enable Movement Function Enable Movement Function The object is used to disable enable movement function The movement function is disabled if the object receives a telegram 0 while it is enabled if the object receives a telegram 1 The movement function default to enable after bus voltage recovery The object is used to disable enable logic function The logic function is disabled if the object receives a telegram 0 while it is enabled if the object receives a telegram 1 The logic function default to enable after bus voltage recovery Table 5 5 Communication object table disable enable illumination movement and logic function 24
10. alue again on e Attention delay time Delap time will be reset Fig 4 8 Parameter window Master Setting 1 1 3 Sensor BF Z2 fold General Master Yalue Illumination Setting Illumination value 1 Illumination Value 2 Movement Setting Movement Value Logic Setting Logic Value 4 bit 0 15 Master Setting Teger Wane 1 byte 0 255 128 When delay start send mode Send one time 1 bit 0 1 lt i i When delay over send mode Send one time 1 bit 0 1 hl T 4 bit 0 15 1 byte 0 255 4 Fig 4 9 Parameter window Master Value Parameter Master value as a slave logic 1bit This parameter is used to set whether the master s own illumination value movement value or logic value all values must be 1bit as a slave input If they are as a slave input the master processes the information in the device internal not via the bus Options None 19 Illumination Movement Logic If selecting none the master s own illumination value movement value or logic value will not influence the telegram values that it sends out on bus If selecting illumination the master s own illumination value as a slave input If selecting movement the master s own movement value as a slave input If selecting logic the master s own logic value as a slave input Note when the master s own illumination movement or logic as a slave input after bus
11. arameters configuration as follows 4 1 Parameter window General Parameter window General can be shown in fig 4 1 Here can set the type of the sensor which is as a Standard Master device or a slave device Here can also indicate the system delay time after voltage recovery the delay time that stabilize the device is fixed for 40s 1 1 3 Sensor BP fold General General Illumination Setting Illumination Value 1 Illumination Yalue 2 Movement Setting Master Movement Value The device type is Me Logic Setting Illumination value EN a Logic Value 1bit dbitTbyte obejct send Master Setting OE enble Master Value 1 bit 4bit 1 byte obeict send eon Fig 4 1 Parameter window General Parameter System delay time after voltage recovery This parameter indicates system delay time after bus voltage recovery for the sensor The delay time is set at 40s in order to stable the device in different conditions it contains 3 seconds for initialization and 37 seconds for stable of hardware During the period of time it can t receive information from other devices and can t also deal with own illumination and movement information unless stable of hardware Parameter The device type is The parameter is used to set the type of the sensor Options Standard Slave Master Parameter Illumination Value 1bit 4bit Ibyte object send The parameter is used to set whether the illumination obj
12. ct mmmmmmmmmmmmmmmnmmmmmmmmmmm mm 22 5 1 Communication object Illumination function 22 5 2 Communication object Movement function 23 5 3 Communication object Logic function 23 5 4 Communication object Master Slave function 23 5 5 Disable enable illumination movement and logic function 24 1 Overview This manual provides detailed technical information about the Sensor BP for users as well as assembly and programming details and explains how to use the Sensor BP by the application examples The Sensor BP is mainly used in building control systems it can be connected with other devices via the bus The Sensor BP connects to the bus though the EIB connection terminals without additional supply voltage The sensor is surfacely mounted mostly on ceiling firstly drilling then fixed by the left and right shrapnel It is available to assign the physical address and set the parameters by Engineering design tools ETS with VD2 VD3 higher than edition ETS2v1 3 It is able to install VD3 file if use ETS3 software Sensor BP is a device that can sense movement signal and brightness signal and transmit induction informat
13. d N Action point 1 Action point 2 p upper threshold Description The sensor has action at point 1 4 in threshold behaviour with hysteresis It has action at all point for sensor in threshold behaviour without hysteresis lower lt lux lt upper Action point 4 f lower threshold Action point 3 Falling Lower threshold lux value without hysteresis action points 1 2 3 4 with hysteresis the action point of 1 4 Parameter Interval time of value cyclic send Base x Factor 1 255 This parameter is used to set the interval time of two telegram values that are sent cyclically The objects of three data types can be sent The time Basex Factor Base option 100ms Is Factor option 1 255 Parameter Send illumination Teleg On bus recovery This parameter is used to set whether the objects send the values after bus voltage recovery the objects of three different types can be sent the values of the objects can be set in the parameter windows illumination value1 2 Options No Yes Parameter If Lux lt Lower If Lower lt Lux lt Upper Lux gt Upper value send mode These parameters are used to set the mode that the illumination objects send the values when the current illumination value is less than lower threshold or is between lower and upper threshold or is greater than upper threshold The parameter If Lower lt Lux lt Upper value send mode wi
14. e the delay time will be reset Parameter When delay start When delay over value send mode The two parameters are used to set the mode that the master objects send the values when the delay start or over Options No send Send one time If selecting no send the objects will be not sent any telegram to the bus if selecting send one time the objects send telegrams for one time The telegram values are set in the follow parameter 1 bit 4bit Ibyte Parameter 1bit 4bit Ibyte This parameter is used to define the telegram values that the master objects send when the delay start and over Ibit 0 1 4bit 0 15 Ibyte 0 255 21 5 Description of communication object The communication objects are the medium that communicate with other devices on the bus which means only the communication object can communicate on the bus Communication objects of each function for sensor are summarized as follows 5 1 Communication object Illumination function N Name Object Function Description Group Addresses Length C R Y T U Data Type Priority Eja Read lux value Read lux value 2 Byte C R T Low JR Name Object Function Description Group Addresses Length C R Y T U Data Type Priority Eja Cyclically send lux value Cyclically send lux value 2 Byte C R Low gis change threshold Lower Change threshold lower 2 Byte EJ a Low meje change threshold Upper Change threshold upper 2 Byte C T S
15. e parameter defines the logic function between input I and input 2 Three logical operations are available AND OR XOR Parameter The logic function type between input 0 and result of input 1 2 The parameter will be seen with enable in the parameter input 0 of logic is which defines the logic function between input O and result of input 1 2 Three logical operations are available AND OR XOR Parameter Logic value cyclical send time Base x Factor 1 255 This parameter is used to set the interval time of two telegram values that are sent cyclically The objects of three data types can be sent The telegram values can be set in the parameter window logic value The time Basex Factor Base option 100ms Is 17 Factor option 1 255 Parameter If logic result 1 If logic result 0 value send mode The two parameters are used to set the mode that the logic objects send the values when the logic result is for 1 and 0 Options No send Send one time Send cyclically If selecting no send the objects will be not sent any telegram to the bus if selecting send one time the objects send telegrams for one time if selecting send cyclically the objects send telegrams cyclically The interval time between two telegrams is set in the above parameter Logic value cyclical send time Base x Factor 1 255 The telegram values are set in the follow
16. e time the objects send telegrams for one time if selecting send cyclically the objects send telegrams cyclically The interval time between two telegrams is set in the above parameter Interval time of value cyclic send Base x Factor 1 255 The objects values are set in the follow parameter logic bit 4bit 1 byte Parameter logic 1bit 4bit Ibyte This parameter is used to specify the telegram values that the movement objects send when the movement start and over Logic Ibit 0 1 4bit 0 15 Ibyte 0 255 When the sensor detects some object moving the delay time start If the sensor doesn t detect some object moving on delay time then the delay time over if the sensor detects some object moving again on delay time the delay time will be reset or continue to travel time set by the parameter Function of movement retrigger The delay time is set by the parameter Delay time of movement Basex Factor 4 4 Parameter window Logic Setting Parameter window Logic can be shown in Fig 4 6 Here can set the logic function which is mainly the integrated use of illumination and movement There are 3 logic communication objects to decide the result of logic output The object default value of input 0 for logic can be set via parameter after bus voltage recovery and can also be modified via the bus The current illumination determines the value of input that can be set in the illumination va
17. ects are enabled Options Enable Disable If selecting enable the illumination objects normally send values If selecting disable the illumination objects will be not visible Parameter Movement Value 1bit 4bit Ibyte object send The parameter is used to set whether the movement objects are enabled Options Enable Disable If selecting enable the movement objects normally send values If selecting disable the movement objects will be not visible 4 2 Parameter window Illumination Setting Parameter window Illumination setting can be shown in fig 4 2 Here can set illumination function illumination can be set from 0 to 65535 and upper threshold must greater than lower threshold The respond mode of the brightness can be also set in the window Illumination function can make three different types of values sending to the bus see chart 4 3 When the current illumination is less than lower threshold the sensor can send the special values of three different types When the current illumination is between lower threshold and upper threshold the sensor can also send the special values of three different types Similarly when the current illumination is greater than upper threshold the sensor can also send the special values of three different types The illumination values sending mode can be set 1 1 3 Sensor BP fold General Illumination Setting Illumination Setting Illumination value 1
18. he bus The movement values sending mode can be set 12 1 1 3 Sensor BP fold General Illumination Setting Illumination value 1 Illumination value 2 Movement Setting Movement Value Logic Setting Logic Value 1 1 3 Sensor BP fold General Illumination Setting Illumination value 1 Illumination Value 2 Movement Setting Movement Value Logic Setting Logic Value Movement Setting Sensitivity can be changed via bus disable Function of movement retrigger disable Delay time of movement Base Factor 1 255 Interval time of value cyclic send Base Factor 1 255 Info Fig 4 4 Parameter window Movement Setting Movement Yalue If Movement start value send mode IF Movement start logic 1 bit 0 1 4 4 bit 0 15 1 byte 0 255 i IF Movement ower value send mode logic I bit 01 1 4 4 bit 0 15 1 byte 0 255 4 Info Fig 4 5 Parameter window Movement value Parameter Set the sensitivity of movement sensor 1 10 This parameter is used to set the sensitivity of movement detecting options l1 10 Parameter Sensitivity can be changed via bus This parameter is used to set whether the sensitivity can be changed via bus Options Disable 13 Enable If selecting enable the communication object change sensitivity will be enabled the sensitivity can be changed via the
19. ion to other devices such as dimmers relays The Sensor BP is mainly used with the brightness of the occasion or the need to monitor the situation if there is subject movement and then it will perform actions Product functions are summarized as follows e Illumination level Olux 65535lux resolution 1lux e Movement detector area high sensitivity 4m 5m low sensitivity Sm 7m eillumination output with 3 data types the values can be sent cyclically movement detector output with 3 data types the values can be sent cyclically e lumination with threshold function e Movement detector sensitivity with level 1 10 e Logic AND OR XOR function among illumination value movement detector value and input value logic output with 3 data types the output values can be sent cyclically eCan be set Master Slave interworking the master output with 3 data types e llumination enabled Movement detector enabled and logic enabled function 2 Technical data power supply Bus voltage 21 30V DC via the EIB bus Current consumption Max 12mA EIB KNX Operation display Connections Sensing distance Temperature range Ambient condition CE norm Certification Mounting Dimensions Weight Power consumption EIB KNX Red LED and push button Green LED flashing EIB KNX Diameter Radius Operation Storage Transport Humidity Max 360mW Assigning the physical address Indicate the device running normally OK Bus connection te
20. ll be not visible if the parameter Threshold behavior is set to with hysteresis Options No send 11 Send one time Send cyclically If selecting no send the objects will be not sent any telegram on the bus if selecting send one time the objects send telegrams for one time if selecting send cyclically the objects send telegrams cyclically The interval time between two telegrams is set in the above parameter Interval time of value cyclic send Base x Factor 1 255 The objects values are set in the follow parameter logic 1 bit 4bit 1 byte Parameter logic 1bit 4bit Ibyte This parameter is used to define the telegram values that the illumination objects send when the current illumination is less than lower threshold and is between lower and upper threshold and is greater than upper threshold Logic Ibit 0 1 4bit 0 15 Ibyte 0 255 4 3 Parameter window Movement Setting Parameter window Movement Setting can be shown in Fig 4 4 Here can set the movement function the sensor will active the moving operation when it detects some object moving Movement function can make three different types of values to be sent the bus see chart 4 5 When the sensor detects some object moving it can send the start values of three different types to the bus if the sensor doesn t detect object moving for a period of time it will send the over values of three different types to t
21. lue parameter and the value is sent via the illumination object The movement determines the value of input 2 that can be set in the movement value parameter and the value is sent via the movement object In the case of input 0 enabled The value of input I makes logic operation with the value of input 2 firstly and then the result after that will makes operation with the value of input 0 According to the final result logic function can make three different types of values to be sent the bus see chart 4 7 When the logic result is for 1 the sensor can send the special values of three different types via the logic objects when the logic result is for 0 the sensor can also 15 send the special values of three different types It will re operate when receiving a new object values as the final output values The logic values sending mode can be set 1 1 3 Sensor BP fold General Logic Setting Illumination Setting Iumination Value 1 input 1 logic bit of illumination value Attention Illumination Value 2 input 2 logic Tbit of movement value Movement Setting Movement Value Logic Setting Input D of logic ts Object value of input for logic Logic Value after bus voltage recovery The logic function type between input I and input 2 The logic function type between input O and result of input 172 Logic value cyclical send time Base Factor 1 255 Ino Fig 4 6 Parameter window Logic Setting 1 1
22. parameter logic 1bit 4bit I byte Parameter logic 1bit 4bit Ibyte This parameter is used to define the telegram values that the logic objects send when the logic result is for 1 and 0 Logic Ibit 0 1 4bit 0 15 Ibyte 0 255 4 5 Parameter window Master Setting Parameter window Master setting can be shown in fig 4 8 Here set the master parameter the window is visible only when the device type is standard master see chart 4 1 Master Slave function of Sensor is normally used in the occasion that a number of Sensors control one or a class of device simultaneously When the master receives the special value from a slave it will send three different type values and the special value can be 0 or 1 If the master doesn t receive the special value on delay time it can also send the values of three different types to the bus The master values and values sending mode can be set in the parameter window master value see chart 4 9 18 1 1 3 Sensor BP fold General Master Setting Illumination Setting Illumination value 1 Illumination Yalue 2 Movement Setting Movement Value Logic Setting Master Delay time Logic Value Baze ls Master Setting Master value Factor 1 255 10 Master value ag a slave logic 1bit illuminatior Master delay start when object slave value receive The master Delay start when receive Attention specitied value If the master recerve the v
23. r send 4bit 4 bit G I Low ms Master send lbyte Master send 1byte 1 Byte C T Low Fig 5 4 Communication object master slave function 23 Po Sswwevane Sevan mm cw The communication is used to receive a value from some slave If the value is with the special value in the parameter master delay start when the follow objects send the values and the delay time will start If the value is not the special value the master is no action 1 2 3 Master send 1bit 4bit Ibyte Master send 1bit 4bit Ibyte 1bit 4bit Ibyte The communication objects are used to send master values of three different data types when the above object receives the special value from some slave or when the delay time is over The master values are set in the parameter 1 bit 4bit lbyte Table 5 4 Communication object table master slave function 5 5 Disable enable illumination movement and logic function Communication objects of disable enable illumination movement and logic functions as shown in fig 5 5 When disable the movement function any movement detector and operation will be ignored When disable the illumination function any illumination to cause change will be ignored When disable the logic function the logic operation will be not performed VAR Name Object Function Description Group Add Length C R W T U Data Type Priority G20 Enable Logic Function Enable Logic Function 1 bit pg Low M19 Enable
24. rminal 7M 3 5M 5 C 45 C 25 C 55 C 25 C 70 C lt 93 except dewing In accordance with the EMC guideline and the low voltage guideline EIB KNX certified Mounted in the ceiling fixed by the left and right shrapnel 91x74x76mm 0 05KG 3 Dimension and induction schematic diagram 3 1 Dimension drawing 76 20 73 75 65 75 e 3 2 Induction schematic diagram WI LD gt H Range 2 5m 3m Recommended value 2 7m W1 Range 4m 5m Range of high sensitivity W2 Range 5m 7m Maximum sensing range Installation Notes 1 Away from air conditioners refrigerators stoves where easily lead to temperature change 2 In the case of a certain temperature the influence of wind is not great for the Sensor 3 When the ambient temperature is close to body temperature the Sensor isn t very sensitive or no response 4 Between the Sensor and person that is detected it can t be space out by furniture large potted plants glass blinds and other objects 5 The Sensor can t be directly on the windows doors and where there is direct sunlight because the hot air out of the window and people movement and the violent change of light all of them will cause the sensor to send unexpected telegram 4 Project design and programming Application Number communication Max number of Max number of program objects group address associations Overvie
25. s of lighting control can be achieved automatically through logic function of Sensor Master Slave function Master Slave function of Sensor is normally used in the occasion that a number of Sensors control one or a class of device simultaneously When the master receives the special formation from the slaves it will output the start value and delay for some time If the master doesn t receive the special formation again on delay time it will output the over value If the master receives the special formation again on delay time delay time will be reset For example several Sensors control a light simultaneously one of slave Sensors is sensitive to moving action then the Slave send out a formation If the formation that the master receives from the slave is the special formation it will output a formation to turn on the light If the delay time has passed the master doesn t receive the special formation again it will output a formation again to turn off the light Illumination enabled Movement enabled and logic enabled function It is convenient for some situation or some cases that need to disable or enable movement illumination detecting or logic function When the movement or illumination function of one sensor is disabled all reaction to the sensor will be ignored about illumination or movement When the logic function is disabled the sensor will no longer carry out logic operation either In the ETS system Sensor BP p
26. there is no telegram to send if selecting respond after read only the brightness value can be read out by other devices if selecting cyclical the current brightness value will be sent cyclically on the bus via the object cyclical send lux Parameter Interval time of cyclical response Base x Factor 1 255 This parameter is visible if the brightness cyclical responding has been select It is used to set the interval time of two telegrams that are sent cyclically The time of cyclical response Basex Factor Base option 100ms Is Factor option 1 255 Parameter Threshold can be changed via bus This parameter is used to determine whether threshold can be modified via bus or not Options Disable Enable 66 It is allowed to change the value by the object change threshold lower upper when selecting enable which can save the input value as the new threshold 1 2 value If selecting disable the threshold 1 2 value can t be changed by the object Note The new threshold value will be saved when bus power down Parameter Threshold behavior The parameter defines the delay status of threshold 1 value and threshold 2 values The delay can avoid the unnecessary behavior caused by the illumination value if its value is between 2 threshold values Options Without hysteresis With hysteresis 10 Difference between lag and no lag Exceeding Upper threshol
27. tion 5 3 Communication object Logic function Communication object logic function can be shown in fig 5 3 H Name Object Function Description Group Addresses Length C R W T UV Data Type Priority 14 Logic result send 1bit Result logic send 1bit 1 bit Cc T Low Hiis Logic result send 4bit Result logic send 4bit 4 bit D fp Low jis Logic result send lbyte Result logic send lbyte 1 Byte C Ff Low 17 input 0 of logic input 0 of logic 1 bit D amp f Low Fig 5 3 Communication object logic function 14 15 16 Logic result send 1bit 4bit Ibyte Logic result send 1bit 4bit Ibyte 1bit 4bit lbyte The communication objects are used to send logic values of three different data types when the logic result is for 0 or 1 The logic values are set in the parameter logic 1b1t 4bit 1 byte The communication object will be seen with enable in the parameter input 0 of logic is It is used to modify the value of input 0 Table 5 3 Communication object table logic function 5 4 Communication object Master Slave function If the device as a slave there will be not parameters setting and communication objects if the device as a master the communication objects can be shown in fig 5 4 H Hame Object Function Description Group Addresses Length C W T UV Data Type Priority r vereren JP E ee PG PE re GE AG on z ne SE ETEN OT EE a A E gt m2 Master send 4bit Maste
28. w of the application program Illumination function This function is mainly used for lighting such as outdoor lighting we turn on the light in the dark but turn off again in the dawn If the manual to control these operations are very trouble but the Sensor can be easily achieve these operations instead of the manual control The Sensor can automatically sense the current illumination to achieve automatic control Movement function The Sensor will carry out action when the Sensor detects an object moving After a period of time if the Sensor is not detected to any object moving it will over the action For example in the public hallway the light is automatically turned on when the Sensor detect people coming and then the light is automatically turned off after people leave for a period of time so as to achieve the maximum energy savings The movement function of Sensor can also be used to control other occasions such as the elevator hall underground garage etc Logic function Logic function is the integrated use of illumination and movement It can combine illumination and movement use For example in controlling home lighting it is possible that the light is automatically turned on when people enter the room But we do not need to carry out this action in the day only in the evening need and the light is automatically turned off when people leave or the Sensor can t detect to any object moving for a time The entire proces
Download Pdf Manuals
Related Search