Home

DNR200V_SERIES_MANUAL_EN_R1_web

Contents

1. 2 Remove the plug from the outlet before cleaning Do not use liquid aerosol detergents Use a water dampened cloth for cleaning 3 Do not use this unit in humid or wet places 4 Keep enough space around the unit for ventilation Slots and openings in the storage cabinet should not be blocked 9 During lightning storms or when the unit is not used for a long time disconnect the power supply antenna and cables to protect the unit from electrical surge FCC CLASS A NOTICE NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense This equipment has been certified and found to comply with the limits regulated by FCC EMC and LVD Therefore it is designated to provide reasonable protection against interference and will not cause interference with other appliance usage However It is imperative that the user follows the gu
2. 2 Taponthe DigiNet NVR HD con B to start the app 3 Tap then or 4 Tap Device Manager 5 22 PM Configuration Device Manager Tap Add Device Manager Relay out Config Favorites Local Config Help 9 Tap Add 6 Configure the following 10 56 AM Not Charging EH Configuration Cancel New Device Save Device Manager 4 Enter a name for your NVR Relay out Config ama NUR y Address tomsmith digimerge net Enter the DDNS address Favorites Port 35000 Enter the Client Port Local Config User Name admin Enter the user name Help Password eeeee Enter the password Channel amount 4 Enter the number of channels e Name Enter a name for your NVR of your choice e Address Enter your DDNS address e g tomsmith digimerge net e Port Enter the Client Port default 35000 e Username Enter the NVR s User Name default admin e Password Enter the NVR s Password default 000000 e Channel amount Enter the number of channels your NVR has 7 Tap Save 8 Tap ES 79 Mobile Connectivity 9 In landscape mode tap a channel and then select the camera you would like to view on the left In portrait mode tap on one of the display areas and select the camera you would like to open Click and then select a camera E gt le Favoritos so EI NVA a Chano101 gt E 5 Channo032 a Channel DigiNet NVR HD Interface You can use DigiNet NVR HD in landscape or portra
3. Cancel The Schedule sub menu allows you to configure the recording schedule for continuous and motion recording It also allows you to configure holiday pre recording and redundancy settings NOTE To use motion recording motion detection must be enabled for the channel For details see Motion on page 28 Configuring the Recording Schedule 1 2 Under Channel select the channel you would like to configure or select All Under Period select the day of the week you would like to configure or select Holiday or All Configure up to 6 separate schedule periods e Configure the start and end time for the time period on the left e Check the types of recording that will apply to the time period onthe right Continuous MD Motion Detection Alarm or MD amp Alarm e A visual representation of the current schedule is shown below 4 Optional Click Copy to copy the selected to schedule to other channels Select the channels you would like to copy to and click OK 9 Click OK to save changes Configuring Pre Recording and Mirror Recording Pre recording determines the amount of time the system will record before events Mirroring allows the camera to record simultaneously to a secondary mirror hard drive and primary recording hard drive NOTE Secondary hard drive must be installed and configured for mirror recording to use mirror recording function To configure pre recording and mirror r
4. IN Shay PTS System Requirements Your system must meet or exceed the system requirements below Description CPU Prerequisites Requirement Core 2 Duo 3 0GHz Windows 8 7 Vista 2GB 912 MB of video memory and above 10 100 BaseT Network 1 Mbps upstream High speed Internet service is required to remotely connect to your system NOTE To connect to your system on Mac please visit www digimerge com for instructions e Port forward the Client and HTTP ports default 80 and 35000 on the router that the NVR is connected to e Create a DDNS account e Enable DDNS in the NVR 39 DigiNet NVR Central Management Software e Enter the DDNS information into the NVR e NVR must have access to the Internet or Local Area Network LAN Installing DigiNet NVR CMS Install DigiNet NVR CMS from the CD included with your NVR or by downloading it from www digimerge com It is recommended to visit www digimerge com for the latest software versions To start the software e Double click the DigiNet NVR CMS icon on the desktop e Click Login e Surveillance System am ad minl 60000 Login NOTE The CMS default User Name Is admin and the Password is admin Adding a NVR from the Local Area Network LAN Once you open the software you can add a NVR Prerequisites e Connect the NVR to a router or switch on the network e Install the CMS on a computer in the same LAN as the NVR 40
5. LLANE or PoE Ports Camera input ports for IP cameras DC 48V Port for 48V DC power supply included for integrated PoE ports Power Switch eSATA Port Connect a self powered external eSATA HDD not included to extend the storage capacity of the system or for data backup For details see Configuring eSATA External Hard Drives on page 33 VGA VGA port to connect the system to a VGA monitor HDMI HDMI port to connect the system to a HDMI TV monitor ALARM IN OUT RS422 RS485 Alarm block to connect PTZ cameras not included or external alarm or motion devices not included MIC e IN RCA port for microphone not included for 2 way audio e OUT RCA port for audio output device e g speakers not included for 2 way audio NET Connect an Ethernet cable not included to connect the system to a router or switch not included USB port Connect a USB mouse or connect a USB flash drive not included for data backup or firmware upgrades DC 12V Port for 12V DC power supply included REMOTE CONTROL 1 Power Press and hold to power off the system Press to power on 2 Playback Controls ML Pause Play In live view press to enter playback mode Press to play pause playback K Reverse Press to reverse playback pause playback b gt Fast Press to increase playback speed Cl Next Press to skip to next video K Previous Press to skip to previous video D Slow Press for
6. DIGIMERGE Right for Business DNR2OOV Series Network Video Surveillance Recorder 4 1080P View amp Record CMS Mobile Apps HDMI H 264 pic MERGE Instruction Manual English Version 1 0 www digimerge com Copyright 2013 Digimerge Technologies Inc Thank you for purchasing this product Digimerge is committed to providing our customers with a high quality reliable security solution This manual refers to the following models e DNR200V Series For more information on this product firmware updates and accessory products please visit us at www digimerge com CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE gt gt CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF THE PLUG TO THE WIDE SLOT AND FULLY
7. OR click To AVI to convert the video files to AVI and save to your local computer NOTE You must stop playback before you may download video files Playback Controls Playback DevRecord Activation Record LocalRecord Downl Device Flir NVR v CAM 1 v Multiple channel _ Multiple channel Binding Parameter Date 3 18 2013 vw Time 12 00 00 AM 11 59 59PM FS Query Mode C Sort by file 6 Sort by time File Type Record Card Type Card Search Result SN Start Time End Time a 2013 03 18 00 00 00 2015 03 18 23 59 5 Pause play Slow Stop Fast q ps Click and drag to select x h playback time Use the g My S7 Sr a E topbartoselectminutes 2 4 5 6 7 8 9 101112131415 16 17 18 19 20 21 22 23 24 To AVI_ Download Play and the bottom to select hours Configuring Monitoring Tasks and Projects Tasks are used to configure the CMS to automatically cycle through different channel arrangements Projects are used to automatically cycle through multiple tasks Configuring Tasks 1 Click Config Manager gt Scheme Task Config 47 DigiNet NVR Central Management Software 2 Click Monitor Task Sohne Tas Conf Click Monitor Task Device 10 0 0 5 18 0 0 8 10 0 0 5h LOD FF 3 Click New 4 Enter a Task Name of your choice 9 Under Window select the split screen mode you would like to show in the task 6 Under Monitor Item configure the foll
8. Page Up t Page Lown Telech lance Backup devica or file Space Required Space Remaining 3 50 G8 14 37 GB e Type Select the recording type you would like to search for or select All to search all recording types e Channel Select the channel you would like to search or select All to search all channels e File Format Select DAV to save files to save files to dav format You can use the Player that is automatically saved on the USB device to playback dav files on PC Mac not supported Or select ASF for asf format You can playback asf files in VLC Media Player free download from www videolan org on PC or Mac e Start Time End Time Select the start and end time for your search 7 Click Add A list of files that match your search criteria appears 8 Check files you would like to backup and then click Start Wait for the backup to complete NOTE HD video files saved on the system may take up a large amount of disk space The size of video files selected and the amount of free space on your USB device is shown at the bottom of the screen Using Video Clip Backup Video clip backup allows you to select a duration of video during playback mode and save It to a USB device not included To use Video Clip Backup 1 Inserta USB flash drive not included or USB external hard drive not included into one of the USB ports 17 Backup 2 Start playing back video using the steps in Playing Back Video from the Hard
9. Type Status Capacity Record Time 3 01 10 18 39 50 13 01 18 17 03 15 eSATA HDD s Click eSATA 9 Double click on the hard drive you would like to configure Z Qr A ESATA 9 10 11 12 1 Name Total Space Free Space SICIUE R Detect Double click hard drive 6 Select Storage to use the hard drive for normal recording or mirroring or select 33 Using the Main Menu Backup to use the hard drive for data backup only Click OK ATTENTION This step will format the hard drive Formatting the HDD erases all data on the hard disk This step cannot be undone a Set Status Status Unknown Type Select Storage Storage or Backup Backup Cancel 7 The NVR formats the hard drive and restarts lf you set the external hard drive for Storage you may configure it for Mirroring or Read only mode the same way you would configure one of the internal hard drives see Selecting Hard Drive Types on page 32 Warning IEN WARNING Event Type No Disk Enable k Save Cancel The Warning sub menu allows you to configure actions taken when system errors occur To configure system error actions 1 Under Event Type select one of the following system errors to configure No Disk Disk Error Disk No Space Net Disconnection IP Conflicted or MAC Conflicted 34 2 Check Enable to enable warnings for the selected Event Type 3 Configure the following actions t
10. Viewing Backup Files se be cert tae trie A da chats Br Sas aS hak BR akon las ae id 2 18 Using the Main Menu 44 lt sesn sve ceae ene a 20 Ortner nea ads Gute Gated rado eta be 21 A o AA NN 21 TD a phe vik tt aga atte eden E E OE 21 e a O A ZI VERSION scorn aras ee ody eae aaa sees pio ea Bee da ia hae see 21 UBdatina FrmMWa E sesis taigako tiroaren A A AAA o dea aaa 21 Onone SCES Sibi he P54 a DAA ANDAS AAA ASADAS AA LE DA Se 22 SU E AAA O aight Bea ahah acd E 22 SOLIS at se canard iad at nee ene 23 CEC Mee Cee OTe ee Cee Le ee eee eT ee ee ee See ae eer eee eee ee re ee er ee Ore ee ee 23 ROCOSAS Ps ae he EGGS ik SAS EA TAS E EGER Ss 24 ENCUADRA hema ob hia E lacie Sar RT Bd E E PE edo A TE gan ee 24 Configuring the Recording Schedule scsi torna boube need eteabedersanes 24 Configuring Pre Recording and Mirror Recording 2 00 ccc cece eee eee eee eee e eens 20 COMUGUEING TIOUCAYS cues e e O terre EA tees A N EEE 20 NA O Hie athe ica RA Toe Bae e a tar le Gad ge Bo Gt a gt AS Tor See 25 Configuring DHCP or Fixed IP Address ai ote gies O dinte ki rrera ou eS ecw 25 COontigurina System F Or ers SR ia 25 AA A pieni aea Batata oth a a a a aa a 060d a we wees a aA 26 OT GING ONIN vate ise 55 A A Bale a NS AOR Ne aes A E 26 COMMGUPING Emails ii tes te oe eal ee ie hie AS ead Bl aed eeu ee ate ont O 27 CONTIGUMING Switch SO UEINGS ri A aa 28 DOOD ea cy st sie iced tak ace ey eae cap BO hey gd dE een ee aa eg ENS 28 Configurin
11. 12V port on the rear panel of the system Connect the power cable to an outlet power strip or surge protector This power adapter is used to power the main unit b Connect the DC 48V power supply to the DC 48V port on the rear panel of the system Connect the power cable to an outlet power strip or surge protector This power adapter is used to power the integrated PoE ports c Turn the power switch to the ON position Connect IP cameras to the system VGA Homi es Connect to an HDMI VGA or BNC monitor i Connect the mouse to a USB port EE Connect an Ethernet cable Connect the power adapters A FRONT PANEL 1 IR Receiver IR receiver for the remote control Keep the IR receiver clear from obstructions 2 LED Indicators e POWER Eva Glows to indicate the system is on e HDD 5 Glows to indicate hard drive is in normal state Turns off when there is a hard drive error e NET Eh Glows when network is in normal state Turns off for network error e ALARM Pay Glows when an external alarm or sensor device not included is triggered 3 Power Button Press and hold to power off the system Press to power the system back on 4 FN Performs special functions in some menus 5 USB Ports Connect a USB mouse included or connect a USB flash drive not included for data backup or firmware upgrades Rear Panel AA REAR PANEL Po IAS de 11 Ground 12
12. Androld PRONES aro rd Gaede a eae A 72 COMPANDICDCVIGCS cn ak oboe nn a ete eh on aaa Bape eee eae E 72 ER SAA Sis pee se O E eee 72 Connecting to your NVR on an Android Phone 2 ii E e AS nannan nnr 72 PUONNV CEN VIATICOS dit A EE AA EI A OG da Ben A A E EDR 74 VII Viewing Snapshots and Videos with Local FIGS ooo ied Using Playback Mode on Andrord Phones 1d es Ok ee eae ae ahi cent tena dy plo e eects 79 EDITION OIC MOS AREA EA AS E TORE REOR 76 DEVICE MaANGOer 1 at ei Pel BS ie Uo Se a ehh in ie Oeil i Ba tae 78 Android Tablels serias rara e das 78 SVSUCIT REGUN emes lp Ad dd e RREN 78 PREIS 2 aora o Ae ee a sea ae eee 78 Connecting to your NVR on an Android Tablet 79 DGIE EIN VIRIL TATCIT ACE td st Dat a e Iles A E EIA me hd Sa E A oe BA eee LA 80 Using Playback Mode on Android Tablets ooo 81 ENnGDUNG PUSH INOUTICAUONS lt lt EA A DA A AE AR A A 82 BE E AO E E e AER EE AAA E E A 8I Appendix A System Specifications 00 eee eee 85 Appendix B Setting up Remote VieWIN9 o oooooooooo oo 87 What DON INGCOS resterna ete edia piek oe ee Soe kee ene wee E 87 How Do Find My IP and MAC addresses 00 e eee eee eee eae 88 FINOING VOU External IP AOU CSS 4 A AAA A AEE SU Toe Bos A or 88 How Do I Enable Port Forwarding 0c cee es 88 Appendix C Auto Port Forwarding Wizard 0 00ococooooo o 90 INSTAULAUION 252m eee ua ao do ia a in a eS e ds 90 Obtaining Your Router Model N
13. Group Select group number Cancel 3 Click OK The system will restart 4 Return to the HDD Manage menu right click gt Main Menu gt Advanced gt HDD Manage Click HDD Channel HDD Channel R channel HDD Group channel HDD Group Select hard drive group for each channel 4 4 4 4 4 4 4 4 h bl bl h mobi mobi mb mb Cancel 5 For each channel select the hard drive group you would like it to record to 6 Click OK Configuring eSATA External Hard Drives You may use up to 4 eSATA external hard drives up to 3TB each for a maximum capacity of 12TB not included by connecting a single self powered eSATA hard drive enclosure not included to the eSATA port on the system eSATA hard drives may be used for backup recording or mirroring hard drives This Is useful because you can store your external hard drive ina separate lock box from the main NVR unit Using the Main Menu To configure eSATA hard drives 1 Connect an eSATA external hard drive to the eSATA port on the rear panel of the system 2 From live view right click and click Main Menu Log in if prompted 3 Click Advanced gt HDD Management NOTE When eSATA HDD s are detected they are located below the internal SATA HDDs If they are not detected restart the NVR 4 Click eSATA HDD Management SATA ul 2 Alarm Set HDD Setting Alarm Release HDD Channel ESATA OZ HDD No v Setto Read Write 7 Execute
14. IDA Es JI Remote Viewing on Internet Explorer 00 0c e cece eee eens 57 PROFOQUISITOS estudie shale stad ede eee oa he Jew ede aa dace 57 IE LVEDD DAV OVE EW aee raa dm Sar BAe ae ie E ech eal ga heath Sun Goole pill a ae eee 58 Using Search Mode INTE MOVIES 2 AA A ada 52 PLD Sc CONTO oros is A AS Dawa A A 60 Mobile CONNSCUVIV sisas as dar 61 IPHONE eee eee ee ee ee ee ee ee Ada A eee ee ee ee RES ee 61 SUSTENTO QUIFENION ES DA SERGI AS EN BE hee RO BERG EOE Raine He Be a Se 61 MELISSA E dt LE E E A A Marcher das Bente 2 61 Connecting to your NVR on an iPhone DD AAA AA AAA AAA eas 61 NONE EN VR INTOFTACO bid E EE AAA A TAS LA EA AA AA AAA 63 Viewing Videos with Local dt ick send hoe Us ek ee ok a DEE A oe eos 63 Using Playback Mode on IF NONE 221 conic ok ate econ verted Ceo anon eee Baio Ba a So 64 ENADUAOT USD INDUCIDOS peppar e eea A AA AAA A AA AA 69 Levice MANAG OF fais A Ih bet pi aan A Oe Ss an ke a ae Sa eee 66 PAGS ssa ot oneal ech A weal no ald ce Ow we Molto Arm lao eee BS a lo 67 SSL REQUIFENVONES sic pa ain SERGI ie Sie BS ODO AGE ates BO gL tee Raa Raine tle ig Bee Se 67 FEOS A E A nce OE A A E A A ad 67 CONNCCHAO to you NVR ON AN IP TO 2 E AA ETA A Ai 67 DIGINC EN VR III TCOITaACO EG A AA AA RA A E ten alt AA 69 TI OVIG O See Soe a trek Bg he ee Oe ee ek es eee ee ee 69 Using Flayback MODE DATE A eae ee AS eek hi IA 70 ENADUNG F USN INVOCA S a x cece DAA dan eee Goel Booed ABN AAA Rk eke he AER yal
15. MERGE Right for Business Need Help e E E E A EA ZE E EE TE E E E E amp E E UN Please make sure to visit our website www digimerge com to receive product updates and information 3 Easy Ways To Contact Us Online k A Product support is available 24 7 including O Information user manuals quick start up guides and FAQ s at www digimerge com By Email Technical support for technical installation issues tech digimerge com By Phone North America 1 866 816 5919 Technical support for technical installation issues Mon Fri 8 00 am to 8 00pm EST We welcome your feedback at HH info digimerge com s For more information visit www digimerge com 20032013_R5
16. Repeat to view additional cameras DigiNet NVR Interface You can use DigiNet NVR in portrait and landscape mode Return to Main Menu ______ E Live Preview Double tap to opena channel in full screen Disconnect from camera Snapshot Connect to camera Change Camera Connectto all previously added t ga p o cameras O EE x Ea Disconnect all m Start stop manual e record PTZ Access Favorites Open image settings 74 Mobile Connectivity Viewing Snapshots and Videos with Local Files If you have saved snapshots or videos using DigiNet NVR you may open them with Local Files To access Local Files e From the Main Menu tap Local Files ba Return to Main Menu s Local Files Delete all files Tap files to open A Open videos mi Open snapshots Using Playback Mode on Android Phones You can access recorded video on your NVR using your Android phone NOTE You must enable Extra Stream Recording to use playback mode on mobile devices For details on enabling Extra Stream Recording see Recording on page 24 To use Playback Mode 1 From the Main Menu tap Playback 2 If Playback is not shown tap Add check Playback and return to the Main Menu 75 Mobile Connectivity 3 Tap and select a channel to playback Playback Tap and select a channel to playback B 4 Select the date then the start and end times to playback 9 Use the on screen con
17. To add a NVR 1 Click Config Manager gt Device Manage AR 0 x Tools Click Config Manager igre Scheme Task Config Record Plan Config Alarm Config Alarm Rec Config E map Contig DecCard Contig User Manage Click Device Manage Device Manage Ext screen manage User Contig if 2 Click Search Device If a Windows Firewall alert appears click Allow 3 Check the NVR and click Add Management Device Manage Device group Click Search Device mmo men ado Depay aa NE a C 7 i Y ii veson 5 eo m s n F Check the NVR A O e Click Add Management A p palava marocanars 4 Enter the User Name default admin and Password default 000000 for the NVR and click OK Add 1 selected devices into management Enter User Name default admin Enter Password default 000000 5 Click OK 6 Click Device List 41 DigiNet NVR Central Management Software 7 Click next to No Group 8 Double click the NVR 9 Click and drag the NVR to the displa y area to view FLIR SyncrolP NVR CMS V4 06 a a x Ee Click Device List mT No group Click Double click the NVR irecti n OO jo PTZ Advanced PTZ D Tools Adding a NVR using a DDNS address If you have NVR systems with DDNS set up you can add them to the CMS Prerequisites e Create a DDNS account For details see Appendix D Setting Up DDNS Service on page 97 e Enter th
18. Using the Camera Toolbar The Camera Toolbar is used to perform actions on a specific channel To access the Camera Toolbar e Move the mouse tothe top of the channel display The Camera Toolbar has the following options Quick Playback Real time Close backup Digital Zoom Device Search Using the System Using Quick Playback Quick Playback is used to playback the last 5 60 minutes of video from the selected channel You can cha also access Quick Playback in split screen mode while still viewing live video from the other nnels To use Quick Playback 1 2 Move your mouse to the top of the channel display and click A NOTE By default the NVR will begin playback from b minutes ago You can increase this to up to 60 minutes using the Realtime Play setting in Main Menu gt Setting gt General Right click to exit Quick Playback Using Digital Zoom in Live Display 1 Move your mouse to the top of the channel display and click to activate digital zoom The icon will change to Y to indicate digital zoom is activated NOTE You may activate digital zoom in multiple channels at the same time Click and drag inside the channel to zoom in e Click and drag to pan the zoom area e Right click to zoom out and select a new zoom area e Click 29 to disable digital zoom Note that the channel will remain at the same zoom level until you right click inside it Using Real time Backup Real time backup allows y
19. can see the software shortcut optional 90 Appendix C Auto Port Forwarding Wizard 9 Click the Next button and then click Finish to complete the software installation __ Digimerge Auto Port Forwarding Setup 7 GE Installation Successful The Digimerge Auto Port Forwarding 1 0 0 installation is complete Thank you for choosing Digimerge Auto Port Forwarding Please click Finish to exit this installer The installer now has enough information to install Digimerge Auto Port Forwarding on your computer The following settings will be used Install folder C Program Files Digimerge Auto Port Forwarding Shortcut folder Digimerge Auto Port Forwarding Please click Next to proceed with the installation Ga 2 e Finish button 6 Double click the Auto Port Forwarding shortcut B4 from your desktop to start the program Obtaining Your Router Model Number and Version On most routers the model and version number can be found underneath the router printed on a sticker Example gt 7 a a 1438 NETGEAR lt co eit if Wireless G Router WGR614 v9 Wireless G Router WGR614 v9 EE A 112 ln a MESI E e WGR614 refers to the model number dr Sola 3 tr d E ev9 refers to the version number i 7 PEET EE 5 F dj 4 4 2 i A a i A q SERIAL MAC Configuration You must have the following before you configure the
20. com Extract the contents Into a folder Open the folder and right click ConfigTool exe and Run as administrator Click Login Under IP Address enter the public IP address of the NVR Edit the User Name Password or Port if these have been changed from the default values padres EntertheNVR s public IP address User Name admi Password Port Cancel Click Login The Config Tool logs in to the NVR Click System Upgrade Click Open select the firmware file bin 101 Appendix E Remote Firmware Upgrade 9 Click Upgrade Wait for the upgrade to complete Do not power off the system or disconnect the power cable during upgrade The system will restart when the upgrade is complete NetWork Parameter PPPOE System Information System Upgrade C li C k Syste m U pg ra d e Upgrade Information Upgrade Fie Open Click Open and select the firmware file Current Progress Upgrade Click Upgrade and select the firmware file 102 Appendix F Hard Drive Installation APPENDIX F HARD DRIVE INSTALLATION The system comes with one or more pre installed 3 9 SATA hard drives You can install up to two hard drives up to a maximum size of 3TB each for a maximum total storage of 6TB Installing a Hard Drive A Make sure that the system is OFF and ALL power adapters have been disconnected before removing installing the hard drive To remove the hard drive 1 Power off the system and unplug a
21. fixed interval Schedule Mode will switch tasks at a pre defined time of the day Project Edit Enter project name Select project type Select task Enter interval or start time Click Add 6 Under Task Name select the task you would like to add to the project e f you selected Tour Mode enter the Interval Time in minutes that the task will run for before changing to the next task e If you selected Schedule Mode enter the time of day when the task will start running 7 Click Add 8 Repeat steps 6 7 for each additional task you would like to add to the project 9 Click OK Click OK to save changes Running Tasks and Projects e Once you have configured tasks or projects you may run them by clicking Task Z then selecting the task or project you would like to run 49 e You may also select a task or project to run when you first launch the CMS For details see Configuring CMS Options on page 52 Using E Map The E Map feature allows you to visually map your cameras over a jpg image Configuring E Map Use the steps below to select a pg image to use for the E Map and place your cameras To configure the E Map 1 Click Config Manager gt E Map Config 2 Click Picture Edit Click Picture Edit 3 Click Add Click Add 4 Click Browse Select a jpg image on your computer to use as the E Map 9 Enter a Name and Title for your E Map of your choice Picture Na
22. rule for downloaded recording files e Device free minimum space MB Enter the amount of minimum space in MB to maintain on the computer hard drive The system will stop recording when only this much space is left e Auto Start Project Check for the CMS to automatically run a project when opened Select the project it will run under Project Name e Auto Start Task Check for the CMS to automatically run a task when opened Select the task it will run under Task Name e Last Run Check for the CMS to start the last used task or project when opened e Save last monitor status Check to have the CMS restore the previously used display mode when opened e Auto sync PC time to device Check to have the NVR sync the clock with the system time on the PC e Sync time becomes valid at Select the time that the NVR will sync its clock with the PC s system time e Week Select days that the NVR will sync its clock with the PC s system time e Auto reboot device Check to enable the NVR to reboot when the time sync occurs 3 Click Ok to save changes Close the CMS and restart it to update the configuration Changing the CMS Admin Password You can change the admin password that is used to log into the CMS The default password Is admin NOTE The CMS will automatically populate the admin password unless you enable Verify Password under Config gt Options To change the CMS admin password 03 DigiNet NVR Central Management Softwar
23. software 1 Your router s model number and version number Your router s user name and password 2 3 Your device s IP address 4 Your device s port numbers that require port forwarding 91 Appendix C Auto Port Forwarding Wizard Initial Startup Select Language 1 Click the Language drop down menu and select a language English French Spanish Click the Start button to continue D i Gl M ERG E Right for Businist Amio Port Forwarding Po aad fq mars Software update section Current Version 1 0 2 WELCOME Update Available Yes heey at 173 with giga Avin mabeg roe cor ee pia New Version 1 0 4 Download Now button Start button A software update includes an updated list of routers compatible with the Auto Port forwarding Wizard Language drop down menu 2 If software updates are available click the Download Now button in the top right corner e Run the update file and install the latest version of the software Step 1 Populate the Router Database The Auto Port Forwarding Wizard automatically populates a list of current routers and detects the number of connected routers 1 Click the Next button after the software detects your router configuration DIG MERGE Righi lor Blame aA l ag he ll ra ta ce Click to update router database Click to check for multiple routers If more than one router is detected you may need to contact your ISP Internet Service Provider to port forw
24. 2478 1552384 1353115 71547 274959 930361 1387588 1759446 1758905 1761403 1757487 1755377 325752 1117532 2036951 1749667 rana e 03 14 2013 12 30 01 03 14 2013 12 44 02 03 14 2013 13 00 02 03 14 2013 13 37 03 03 14 2013 14 00 02 03 14 2013 14 13 36 03 14 2013 14 20 18 03 14 2013 14 36 20 03 14 2013 15 00 00 03 14 2013 15 30 00 03 14 2013 16 00 00 03 14 2013 16 30 01 03 14 2013 17 00 02 03 14 2013 17 30 00 03 14 2013 17 35 44 03 14 2013 17 55 03 03 14 2013 18 30 01 MAA A A A NA NA 03 14 2013 12 44 02 03 14 2013 13 00 02 03 14 2013 13 26 43 03 14 2013 14 00 02 03 14 2013 14 12 19 03 14 2013 14 18 24 03 14 2013 14 36 10 03 14 2013 15 00 00 03 14 2013 15 30 00 03 14 2013 16 00 00 03 14 2013 16 30 01 03 14 2013 17 00 02 03 14 2013 17 30 00 03 14 2013 17 35 34 03 14 2013 17 54 53 03 14 2013 18 30 01 03 14 2013 19 00 01 94 AM AAAs Regularhdain Stream RegularMain Stream Regularhd an Stream Regular ain Stream Regularhd ain Stream Regular ain Stream Regular ain Stream Regular ain Stream RegularMain Stream ReqularMain Stream RegularMain Stream Regular ain Stream Regularkd ain Stream Regular ain Stream Regular ain Stream Regular aim Stream Regular ain Stream DO the v gt r Page Down Backup device Search Backup type Dav X Left Space KB Director Device Name Download process KB s Playback Controls Select playback time 60 Play Pause Slow Stop Fast
25. 7 164 234 193 Secondary DNS Server 207 164 234 129 Enter 192 168 1 100 into the DMZ Host IP section into Router 2 IP Address 192 168 171 100 Assigned by Router 2 In both scenarios the router that is immediate to the internet connection Router 2 in illustration must act as a bridge to another router Router 1 in illustration The Auto Port Forwarding Wizard must connect to Router 1 A proper DMZ configuration in Router 2 allows all incoming traffic going through Router 2 to automatically pass to Router 1 Router 2 acts as a dummy router and passes all the incoming data onto Router 1 Router 1 is the router that needs the port forwarding Information 95 Appendix C Auto Port Forwarding Wizard Configuring a DMZ host connection Example e Connect to Router 1 on your network referred o DMZ stands for Demilitarized Zone Enabling a DMZ to as Possible 1st Router in the Auto Port IP on your router enables one of the routers to pass Forwarding Wizard Obtain the IP address of An AO Router 1 Usually this can be found inthe Status section of your router menu The IP should begin with 192 168 This IP address is your DMZ IP e Enter the IP address obtained from Router 1 into the DMZ section of Router 2 192 168 1 100 DMZ IP address assigned by a secondary router f Apply f Cancel e Once you have configured Router 2 with a DMZ connection run the Auto Port Forwar
26. Check to allow the CMS to log into all NVR s when it opens e Auto start record plan Check to have the CMS automatically start the record plan which allows recording to the computer hard drive when it opens To configure the record plan click Config Manager gt Record Plan Config 92 DigiNet NVR Central Management Software e Auto Login Check for the CMS to automatically log in the admin account when it is opened e Hotkey Setup Configure hotkeys forthe CMS Use the drop down menu to select the command and then click inside the box on the right and enter the hotkey NOTE Do not use F12 as a hotkey F12 is reserved for the system debug command e Displayed items in the right bar Select which right side menu Is opened when the CMS opens e Record Time M Select the length in minutes of video files recorded on your computer hard drive For example if you select 15 minutes the system will save a new video file for every 15 minutes of recording e Snapshot picture path Click to select the default save folder for snapshots e Picture file name rule Click to define the file name rule for snapshots e Recorded file path Click to select the default save folder for manual recordings e Recorded file name rule Click to select the file name rule for manual recordings e Downloaded file path Click to select the folder for downloaded recording files e Download record file name rule Click to define the file name
27. DDNS account To setup your free Digimerge DDNS account 1 Inyour browser goto http ddns digimerge net and click Create Account 2 Complete the Account Information fields with your personal information Complete the F Login Warranty Information with your purchase F SERIES RELANTI details optional Pret Eee 3 Complete the System Information fields Digimerge e Product License Select your product model from the Product License drop down menu li e DNR200 e Product Code gt MAC Address Enter the MAC address of your NVR To find the MAC account intormation address press the Enter button on the remote a aei Create a DDNS account Password control OR left click on the screen enter the OEA casado admin password default 000000 and then Prst name Tan click all Country Canada y e URL Request Choose a URL for your DDNS SATA connection i e your name your company or amp _ _eeeeeee business name or anything of your choice Enter personal information 4 Once the information has been entered click Create New Account 9 Your Account information will be sent to you at the email Address you used in Step 2 System Information Product License 123456789045 lt Product Codes lt MAC Address URL Request tomsmith dans digimerge net What is this foal 3 35 ie J w Create Hew Account System information You will need this information for remote access to your system Re
28. Drive on page 14 3 Click to mark the beginning of the video clip Click again to mark the end of the video clip 4 Click to open the Backup menu From ReadWrite Hdd eae DA RECORD During Playback clickto selectstartand end O As Click to open backup menu Ss SS Se SS A All Record 4 Normal 9 Check the USB device where you would like to save the file 6 Check the files you would like to backup Name Type tSpace Total Space Device Status v sdb1 USB DISK 826 00 MB 953 50 MB Ready Check the USB device Remove ime End Time Size KB Check the USB device 00 00 01 03 19 13 00 00 10 9862 7 Click Start Wait for the backup to complete before removing the USB flash drive Viewing Backup Files To playback dav backup video files use the Player that is automatically installed on the USB device when you save a backup file NOTE The Player is PC compatible only For Mac users make sure to save backup files in asf format select ASF under File Format You can playback asf backup video files in VLC Media Player free download from www videolan org on PC or Mac To view backup video files using the Player PC only 1 Insert the USB device into your computer Open the USB device in Windows Explorer 2 Right click the Player exe file and select Open as administrator The Player opens and begins playing all video files on the USB device in sequence Backu
29. Forward Mobile Connectivity MOBILE CONNECTIVITY The DNR200 Series is compatible with iPhone iPad and Android devices iPhone DigiNet NVR is an iPhone app that allows you to remotely view your NVR System Requirements e iOS 4 3 or later Prerequisites e Port 80 and 35000 or your HTTP and Client Ports if you have changed them must be port forwarded to your router e You must create a DDNS account and have the DDNS settings configured in your NVR e The NVR must have Internet access e You must have a DDNS address to log in remotely e An lunes account NOTE You will need to create an iTunes account before you can download the app An iTunes store account requires a valid credit card number The app Is free of charge Connecting to your NVR on an Phone 1 Download DigiNet NVR for free from the App Store 2 Taponthe DigiNet NVR icon a to start the app 3 Tap Mi 4 Tap ua Ol OO T Device Manager 61 9 Tap Add gt Manually Add 6 Configure the following Device Manager Tap Add e Name Enter a name for your a NVR of your choice Enter a name for Name tomsmith your NVR e Address Enter your DDNS i hda the DDN address e g Address tomsmith digimerge net H a S tomsmith digimerge nel Port 35000 e Port Enter the Client Port default 35000 Username admin Enter the user name Enter the Client Port e Username Enter the NVR s barat Asia
30. INSERT Important Safeguards In addition to the careful attention devoted to quality standards in the manufacturing process of your video product safety is a major factor in the design of every instrument However safety Is your responsibility too This sheet lists important information that will help to assure your enjoyment and proper use of the video product and accessory equipment Please read them carefully before operating and using your video product Installation 1 Read and Follow Instructions All the safety and 8 operating instructions should be read before the video product is operated Follow all operating instructions 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings Comply with all warnings on the video product and in the operating instructions 4 Polarization Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other 9 A grounding type plug has two blades and a third grounding prong The wide blade or the third prong 10 are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the 11 obsolete outlet 9 Power Sources This video product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your loca
31. N rn A E ARA 8 ae ee ee ea 38 DigiNet NVR Central Management Software 00 0 o000 2 32 System Requirements sis cc s wkee deere hate gne sided kee lade Geeks 39 PrErGOUISIIGS sas es areas setae eed 5S ee SAA e wae A 39 Installing DigiNet NVR CMS secure seewales ved bows A eee oS ew SEER 40 Adding a NVR from the Local Area Network LAN oooooooomommo 40 V Adding a NVR using a DDNS addresSS occcccccccc ee 42 CMS Live VIEWING OVE W suban dor a e 44 Using Alarm Rec Event Search lucran arrastre das 45 Using Playback Mode 2036462 ica daicrr ceda 46 EE AE OLS A A OE 47 Configuring Monitoring Tasks and Projects 000 cece eee es 47 CONMIGO ING TA SIS it hc dtc Bone ts ed aed had dice Bea eg a te a ead ac ace a da li aa 47 COMO UTING FF O OCIS A wae Mek ends ake AAA A a A A ahaa see 48 Running TASKS and LOCOS tad em ES AROS Ae is AD RoE Rae a E 49 USMO I eM cee hehe to ies fr nee pce nae Boneh Poa ce Gots Ob ad ute ec Sos a eee ey dese 90 CONO URI Te IVI AOS A A A A A ta 50 Opening Cameras Mom E Map sde a ib di any A ee eE 51 CONMGUPINGINne CMS sesira a a oe a a a a a a 52 CONNGUFING C MSDS a ii A AS Dt E 52 Changing the CMS Admin Password 020 ERA A A DA A A A AREA AGRA 53 Adding User Accounts to the CMS cc nrnna 54 MUUI MONIORSUPPOM s sews ear a E al ira da idas 99 Opening Cameras in Secondary MonitorS ici A AD EB AE AR A A A EEN OA 55 Managing Secondary Monitors AI AA AAA IRAN
32. NS Service on page 97 87 Appendix B Setting up Remote Viewing How Do Find My IP and MAC addresses The IP and MAC address of your system are necessary for DDNS setup DDNS allows you to view and control your system from a remote location To find your IP and MAC address e Press Enter on the remote control e Left click to open the Navigation Bar Login if prompted Click E to open the System Info screen Y INFO 0 Device Type NVR Firmware Version 2 610 GM00 0 IE Version iy WF Be gs IP Address 4 IP address MAC Address SMa ee mee CTC MAC address DDNS Name DDNS is closed HDD Capacity vere Video Format NTSC Client Port Eolo LO _ O __ Client Port HTTP Port 80 _ gt gt m2 z m 2 HTTP Port Finding Your External P Address If you wish to find your external IP address you can use a third party website such as http whatismyip org Your external IP address can also be found within your Router settings Refer to your router s user guide for further details How Do Enable Port Forwarding You need to enable port forwarding on your router to allow for external communications with your system for the following ports e 80 HTTP Port e 35000 Client Port Computers NVRs and other devices inside your network can only communicate directly with each other within the internal network Computers and systems outside your network cannot directly communicate with these devices When a system
33. S Service Connecting to your system using DDNS NOTE You must port forward ports on your router to NVR s IP address by default ports 35000 and 80 to connect to your system over the Internet Now that you have set up your system for DDNS use the following address formats to connect CMS Software or Mobile Apps tomsmith digimerge net DDNS address e For details on the CMS Software see DigiNet NVR Central Management Software on page 39 e For details on mobile apps see Mobile Connectivity on page 61 Internet Explorer http http tomsmith digimerge net 80 Colon DDNS address HTTP port number e For details see Remote Viewing on Internet Explorer on page 57 99 Appendix E Remote Firmware Upgrade A APPENDIX E REMOTE FIRMWARE UPGRADE To perform a firmware upgrade over the LAN or Internet a Config Tool is provided on the CD or www digimerge com In an effort to continuously improve the functionality of our products firmware upgrades are available as a free download on www digimerge com as they are released NOTE The Config Tool is supported on PC only You may also upgrade the firmware using the NVR s local menus see Updating Firmware on page 21 Installing a Firmware Upgrade Over the LAN Prerequisites e Connect your NVR to a router or switch on your network e Download a firmware upgrade from www digimerge com If one Is available Extract the contents To perform a fir
34. To use Playback Mode 1 From Live View tap ES then el 2 In Portrait Mode Tap select the start time and end time for your search and select the camera you would like to playback OR In Landscape Mode Select the start time and end time for your search and select the camera you would like to playback Select start time Select end time Select camera 3 Use the playback controls Pause play IA ex file Previous file NOTE Playback controls are only shown in portrait mode 70 Mobile Connectivity Enabling Push Notifications You can have the app send push notifications to the notifications area on your device when one of your cameras detects motion Once you have received a push notification you can select it to open live video from the camera that detected motion er AA Dl sie ne aes ae Se Hye ae de el far Fa Fi UN AT PM de E a EA a ee her Eig nvrlan Channel 3 Push notification Motion Detect 2013 03 25 14 44 21 NOTE Your cameras must have motion detection activated to receive push notifications For details on enabling motion detection see Motion on page 28 To enable Push Notifications 1 From live view tap BH then fod 2 Tap Alarm Push 3 Set the slider to ON next to the NVR you would like to configure Configuration Push Config Device Manager Set to ON Channel Config 2 41 PM Configuration Push Contig nurlam Device Manager Forio
35. Update to test the server settings entered and manually sync the system time 9 Click OK Click Save to save your changes Configuring DDNS DDNS DDNS Type MYDDNS FLIR ME amp Enable R Default Status The DDNS Setup window allows you to enter your Digimerge DDNS settings in the NVR This step is required for remote access Prerequisites e Create a DDNS account For details see Appendix D Setting Up DDNS Service on page 97 e Port forward ports on your router to NVR s IP address by default ports 35000 and 80 e Have your DDNS account name password and domain name ready To configure DDNS settings 1 Click Network Setting 2 Check DDNS 3 Double click DDNS 4 Ensure Enable is checked The box will be white when DDNS is enabled 5 Under Domain Name enter the Domain Name from the confirmation email you received after registering for DDNS 6 Under User ID enter the User Name from the confirmation email 7 Under Password enter the Password from the confirmation email 8 Click OK 9 Click OK 10 Click Save Connecting to your system After you have port forwarded the required port created a DDNS account and enabled DDNS on your system you must enter the DDNS URL into Internet Explorer to access your NVR The DDNS URL must include http the name of your DDNS URL followed by a colon then the port number of your NVR For example http tomsmith digimerge ne
36. ago on the selected channel e Mouse Property Click MouseSet adjust the double click speed and click OK e Startup Wizard Check to enable the Startup Wizard when your system starts lt is recommended to disable Startup Wizard once you have configured the system e Navigation Check to enable the System Toolbar that appears when left clicking on the screen e Auto Logout Enter the amount oftime the system will wait before logging a user out when Idle e IPC Time Sync The NVR will regularly sync the internal clocks of connected IP cameras Enter the interval between time syncs NOTE Click OK when finished making changes 23 Using the Main Menu Recording Recording Channel 1 Type Regular Substream1 7 Compression H 264 H 264 Resolution 1080P CIF Frame Rate FPS 25 FPS ASS ARS Bit Rate Type VBR 7 VBR Quality 6 ATE Bit Rate Kb S Customi 1280 Customi 48 Reference Bit Rate 1280 7168Kb S 48 256Kb S Audio Video Audio Format G711u z Default Cancel The Recording sub menu allows you to configure image quality settings for the recording stream and sub stream used during remote connection Settings for the recording stream are shown on the left and sub stream settings are shown on the right To configure recording quality settings 1 Under Channel select the channel you would like to configure 2 Under Type select the type of recording you would like to configure Regul
37. ar continuous recording MD motion detection recording or Alarm 3 Under Resolution select the resolution for the selected recording type Settings avallable depend on the model of IP camera connected 4 Under Frame Rate select the frame rate for the selected recording type on the left Select the frame rate for the sub stream on the right 5 Under Bit Rate Type select CBR Constant Bit Rate or VBR Variable Bit Rate for the selected recording type on the left and sub stream on the right If you select VBR select the Quality from 1 lowest to 6 highest 6 Under Bit Rate Kb S select the bit rate for the selected recording type on the left and the sub stream on the right 7 Under Audio Video check the box on the left to enable audio recording camera must have microphone attached Check the box in the middle to enable audio 24 streaming to remote users Check the box on the far right to enable video streaming to remote users un check to hide the channel from remote users 8 Optional To copy settings to other channels click Copy select channels to apply settings to and click OK 9 Click OK to save changes Schedule A SCHEDULE Channel 1 v PreRecord 4 sec Mirroring Holidays Setting X Period Thu Record Type Continuous MD Alarm MD amp Alarm Period 1 a 24 Period 2 24 Period 3 24 Period 4 24 Period 5 gt 24 Period 6 24 MD amp Alarm 18 Default Copy
38. ard Pear bery ee ri doin pe lora den dd d Er ee rn dl r rome Gat ane eee a n For details on configuring multiple routers see Configuring Multiple Routers on page 94 Step 2 Enter your Router Settings 1 Under the Router drop down list select the model of your router OR e Click the Search button A to enter the name of your router model NOTE Click the Auto Detect button il if you have a Linksys or Netgear router works with most Linksys or Netgear models 92 Appendix C Auto Port Forwarding Wizard DIGIMERGE Rhi he Elina iao Pon Parmi dina pte 1 i a yr Po dl y F A e N lE step 253 Router drop down list n and Auto detect utton Enable Silent Mode 7 Monten Lente i Router IP a Router user name amp password Enter ports 80 and 35000 under Ports ra Ber 2 Under Router IP click the Detect Router IP button al e The router s IP populates in the blank field Click OK to exit the prompt 3 Under Username and Password enter fhe routers username and password e Optional Under HTTP Type default http and HTTP Port default 80 you may have to change the values depending on your router model Consult your router manual for details DIG MERGE Right tor Business sum Pon coran as i l ale e a E a f Digimerge Product Information w Step 273 Enter your device s IP Enter port Some Digimerge numbers products require multiple ports if your Digirnerg
39. avigation Default Cancel The General sub menu allows you to Configure the time and general system settings The General sub menu contains the following options e System Time Select the current date and time and click Save to save changes e Date Format Select the date format YYYY MM DD MM DD YYYY or DD MM YYYY e Date Separator Select if you would like a dot dash or slash to separate the date display e DST Check to enable daylight savings time adjustments lo configure the startand end times for daylight savings click Set Then configure the Start and End as needed and click OK e Time Format Select 24 HOUR or 12 HOUR e Language Select the system language e Video Standard Select NTSC North America or PAL Europe Using the Main Menu e Device No Select the Remote control ID for the NVR e Device ID Enter a custom name for the NVR e HDD Full Select Overwrite for the system to begin overwriting the oldest recordings when the hard drive is full or select Stop Recording for the system to stop recording when the hard drive is full e Pack Duration Enter the desired pack duration The pack duration determines the duration of video files saved to the system e Realtime Play Select the duration of videos that will be played back in Quick Playback mode For example If Realtime Play Is set to 5 minutes Quick Playback will start playing back video recorded from 5 minutes
40. cessor e 6 GB of RAM e Geforce 990061 video card 1GB or greater Opening Cameras in Secondary Monitors e To open a single channel on a secondary monitor Open it in a wndow on the main screen then right click on the display area and select Output current window to extension screen Select the monitor you would like to send the channel to e To open multiple channels on a secondary monitor Open your desired channel view then right click in the display area and select Output all windows to extension screen Select the monitor you would like to send them to Right click and select output option to open channels on a secondary monitor Managing Secondary Monitors Use Ext Monitor Config to configure settings for secondary monitors You can select which monitors you would like to enable Enabled monitors start up when you open the CMS software You can close secondary monitors by clicking on them and then pressing ESC However you must close the CMS software and restart it to re open windows on secondary monitors To manage secondary monitors 1 Click Config Manager gt Ext Screen Manager D9 2 Click Search to detect secondary monitors or Identify to display the monitor number assigned to each secondary monitor Screen list Click to detect monitors Title Click to show monitor Extension screen 1 number on screen Extension screen Screen information SN 1 _ _ _ ___ _ __ Screen Mame Extension sc
41. configuration to a USB flash drive 1 Insert a USB flash drive into one of the USB ports on the system 2 Right click and select Main Menu gt Advanced gt Config Backup 3 Check the USB flash drive you would like to export to In the list 37 Using the Main Menu 4 Click Export To import a saved system configuration 1 38 Insert a USB flash drive with a saved system configuration into one of the USB ports on the system Right click and select Main Menu gt Advanced gt Config Backup Check the USB flash drive with the saved system configuration file Click Import Click OK The system will restart SHUTDOWN Shutdown Use the Shutdown menu to shutdown restart or log out of the system To access the Shutdown menu Th From live view right click and select Main Menu Login if prompted 2 Click Shutdown 3 Select one of the following EE SHUTDOWN Logout menu user Password is needed to re enter the menu after logout OK Cancel e Logout menu user Log out the account that is currently active e Switch user Log out the account that is currently active and sign in with a new account e Shutdown e Restart system 4 Click OK to complete the selected action DIGINET NVR CENTRAL MANAGEMENT SOFTWARE DigiNet NVR is a central management software that allows you to view and manage multiple DNR200 series NVRs TC des a avis va ar x a TN E
42. connection to the system s web browser interface The default port number is 80 e UDP Port Used for special applications The default port number is 35001 e RTSP Port Used for special applications The default port number Is 554 You must port forward the TCP Client Port and HTTP Ports to enable remote access to the system To configure ports 1 Configure the TCP Port Client HTTP Port UDP Port and RTSP Port fields as needed NOTE Please note that if the HTTP Is port is anything other than 80 you must enter http before the camera s IP address and colon and the HTTP port after the IP address when connecting using an Internet browser le g ifthe HTTP port is 85 enter http 192 168 x x 85 2 Click Save The system will restart to update the ports used Configuring NTP NTP Server IP pool ntp org Pon 123 Time Zone GMT 05 00 Update Period 24 Default Cancel Manual Update You can sync the system clock with an Internet NTP time server To sync the system with a time server 1 Click Network Setting 2 Check NTP 3 Double click NTP to open the configuration menu 4 Configure the following e Under Server IP enter the IP or DNS address of the NTP server 26 e Under Port enter the NIP server port number e Under Time Zone select your time zone e Under Update Period enter the interval your system will sync the time with the selected server TIP Click Manual
43. cord your information below User name Domain name Password 97 Appendix D Setting Up DDNS Service How Do Enable DDNS On My System Once you have registered for free DDNS service use the information in the confirmation email to configure DDNS settings on your system To enable DDNS on your system 1 In live view right click and then click Main Menu Login using the admin account if prompted default user name is admin and default password is 000000 2 Click Setting gt Network 3 Click Network Setting Click Network Setting ANT Detaun Check DDNS 5 Double click DDNS NETWORK SETTING IF RLTER Tnisted Sies 0 NTF pocinip org 24 MUC TEAST Sad DL Ad Check DDNS then PPPOE double click DDNS id No Available DONS Setup PNP Pon Forwarding aa Selling WIFI SETTING Ho Connection EMAIL MalServer 583 FTP Record FTP 0 0 0 0 REGISTER 0 0 0 0 3000 Swich Settings 10 111 6 Configure the following e Ensure Enable is checked The checkbox will be white when DDNS is enabled e Under Domain Name enter the Domain Name from the confirmation email you received after registering for DDNS e Under User ID enter the User Name from the confirmation email e Under Password enter the Password from the confirmation email 7 Click OK 8 Click Save NOTE It may take between 10 15 minutes for the DDNS server to update with your new DDNS address 98 Appendix D Setting Up DDN
44. d Type Channel Contig Motion Detect Push Contig Check each channel you would cam like to receive push notifications Alarm Qut CAM 2 from Favores CAM 3 2 cama Local Contig gt Camera Masking Help gt Local Alarm 71 Mobile Connectivity 9 Tap OK A test notification will be sent to your device After this whenever the selected cameras detect motion you will receive a notification NOTE You can see a list of notifications through the Event List menu To show the Event List menu from live view tap ES then E nu F Alarm event Tap onan eventto view live video from the camera g 08 25 14 43 29 Motion Detect Channela nyrian 03 25 14 43 19 Motion Detect Channel 3 nvrian 03 21 16 04 42 Motion Detect Channel 1 nvr 03 21 16 04 16 Motion Detect Channel 1 nvr 03 21 16 03 59 Motion Detect Channel 1 nvr 03 21 16 02 08 Motion Detect Channel 1 v 03 21 16 01 29 Motion Detect Channeli nvr 08 21 15 59 06 Motion Detect Channeli nvr da 93 21 15 58 23 Motion Detect Channel 1 nvr Android Phones DigiNet NVR allows you to remotely view your NVR on Android smartphones A separate app is available to remotely view your NVR on Android tablets to make better use of the larger screen size For details see Android Tablets on page 78 Compatible Devices e Android OS 2 2 and above Prerequisites e Port 80 and 35000 or your HTTP and Client Ports if you have changed the
45. d or the video product manufacturer s instructions have been followed Attachments Do not use attachments unless recommended by the video product manufacturer as they may cause a hazard Camera Extension Cables Check the rating of your extension cable s to verify compliance with your local authority regulations prior to installation Water and Moisture Do not use this video product near water For example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement near a swimming pool and the like Caution Maintain electrical safety Powerline operated equipment or accessories connected to this unit should bear the UL listing mark of CSA certification mark on the accessory itself and should not be modified so as to defeat the safety features This will help avoid any potential hazard from electrical shock or fire If in doubt contact qualified service personnel video equipment on an unstable cart stand tripod or table The video equipment may fall causing serious damage to the video product Use this video product only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the video product Any mounting of the product should follow the manufacturer s instructions and use a mounting accessory recommended by the manufacturer Service ise 14 1o 16 ile 18 i Servicing Do not attempt to service this video equipment yourself as ope
46. der to access your system 3 An attention bar appears at the top or bottom of the screen to prompt you to install ActiveX plugins click Install or Allow and follow the prompts to install the plugins 4 Enter the system user name and password by default admin 000000 5 Select LAN to connect using the main high quality stream Select WAN to use the sub stream to conserve bandwidth and for improved performance when connecting over the Internet 6 Click Login to log in Enter the system User Name and Password 97 7 Click and drag cameras to the display window to view them live IE Live Display Overview NOTE Some options are not available in WAN mode 1 Cameras Click and drag to the display area to view 2 Live View Controls e Open All Click to open all cameras 08 Remote Viewing on Internet Explorer e Local Play Open recorded or back up video files dav saved on the local computer e Refresh Click this button to refresh monitor channel name 3 Camera Controls Manual Record Digital Zoom Snapshot Close Click and drag to select area NOTE Manual Recordings are saved to C RecordDownload Snapshots are saved to C PictureDownload You must select Run as Administrator when you open Internet Explorer to use these functions 4 Live View Toolbar E E El O E E E E E E El E Select image Full screen quality Fluency Select display view Latency 5 PTZ Controls 6 Colo
47. devices For details on enabling Extra Stream Recording see Recording on page 24 To use Playback Mode 1 From the Main Menu tap Playback NOTE If Playback is not shown tap Add check Playback and return to the Main Menu 2 Tap Playback Tap 3 Select the start and end times to playback 4 Select a channel to playback Select start time OL 2013 03 25 10 46 00 Select end time OL 2013 03 25 11 46 00 Select channel gt nvr 64 Mobile Connectivity 9 Usethe on screen controls to control playback Playback Double tap to open in full screen Next frame Play pause Fast Slow Select next video file Select previous video file Enabling Push Notifications You can have the app send push notifications to the notifications area on your device when one of your cameras detects motion Once you have received a push notification you can select it to open live video from the camera that detected motion Push notification nvrlan Channel 1 Motion Detect 2013 03 25 12 LA E 7 NOTE Your cameras must have motion detection activated to receive push notifications For details on enabling motion detection see Motion on page 28 To enable Push Notifications 1 From the Main menu tap Push Config NOTE If Push Config is not shown tap Add check Push Config and then return to the Main Menu 2 For the NVR you would like to configure set the slider to ON Ht Push Con
48. ding Wizard to begin auto port forwarding to Router 1 e Consult your router s owner s manual for details on configuring DMZ settings Locating your Router IP The Status Page The Status Page of a router normally includes the router s vital information such as the IP address EXAMPLE Product Page DER 615 Hardware Version B2 Famware Version 2 25 ADVANCED STATUS SUPPORT AN of yar WAN and LAN Eaa deeds ane derisyed hera All of your Internet and network connection details are displayed on this page The firmware displayed here wersion is also Time Februsry D6 04 8 23 18 AM Firmware Version 2 25 2008 10 30 The IP information is normally under a Connection Type DHCP Client header called WAN or QoS Engine Active Internet Port Each PE FRSA Se eee router has different Network Status Established terminology Connection Up Time 0 Days 0 48 36 MAC Address 00 1E 58 2E 43 44 f Ain eae ee Router IP assigned by the main router Enter this IP into the DMZ section of the primary router Subnet Mask 255 255 255 Default Gateway 122 168 1 1 Primary DNS Server 207 164 294 193 Secondary DNS Server 207 164 234 129 96 Appendix D Setting Up DDNS Service APPENDIX D SETTING UP DDNS SERVICE Digimerge offers a free DDNS service for use with your NVR ADDNS account allows you to set up a web site address that points back to your local network The following outlines how to set up your free
49. e Auto Maintain AUTO MAINTAIN Cancel The Auto Maintain sub menu allows you to configure your NVR to automatically reboot once a day or once a week For system stability It is recommended to enable auto rebooting The Auto Maintain sub menu also allows you to setthe NVR to automatically delete files that are older than a specified number of days Using the Main Menu To configure Auto Maintain settings 1 Under Auto Reboot System select the day of the week you would like the system to reboot on select Everyday to reboot the system everyday or select Never to disable auto rebooting On the right select the time of day you would like the system to reboot 2 Under Auto Delete Old Files select Never to disable auto deleting of old recordings or select Customized to enable auto deleting elfyou select Customized enter the number of days the system will retain recordings NOTE The system must have sufficient storage space to keep recordings for the specified duration 3 Click OK to save changes Contig Backup CONFIG BACKUP Mame Typs Left Space Total Space J l a a f nz p Ace edb 1 USE DISK 726 50 MBM 95 GB EXPORT MEORT The Config Backup sub menu allows you to export your system configuration to a USB flash drive not included or to import a saved configuration You can Import a saved configuration from another NVR of the same model and channel configuration To export the system
50. e 1 2 3 4 tf When logged in as the admin account click Configl moy Password Under Old Password enter the old password Under New Password and Confirm Password enter the new password Change Password Old Password Enter old password New Password Enter new password Confirm password Click OK Adding User Accounts to the CMS You can add multiple user accounts to the CMS with varying levels of access to the system NOTE To make sure users must enter their user name and password to access the CMS you must make sure Verify User is checked and Auto Login is unchecked in Config Options For details see Configuring CMS Options on page 52 To add a user account to the CMS 1 Za 3 4 94 Click Config Manager gt User Manage Click Add Click Add Configure the following e User Enter the user name for the account e Password Confirm Enter the password for the account e Name Sex Information Optional Enter descriptive details about the user account e Right Check the permissions that will apply to the user account Click Save Click OK to save changes Multi Monitor Support The CMS supports up to 4 monitors on a single system The recommended system specifications is listed below If your system does not meet the requirements below you may experience slow system performance Minimum system recommendations to run the CMS on multiple monitors e Intel Core 15 or 17 pro
51. e Notifications 2 a 2013 03 25 11 22 47 Push notification a Screenshot captured NOTE Appearance of notifications may differ depending on the model of your device NOTE Your cameras must have motion detection activated to receive push notifications For details on enabling motion detection see Motion on page 28 To enable Push Notifications 1 From live view tap then fod 2 Tap Alarm Push 3 Select the NVR you would like to configure Config Alm Push Denes Site mer Channel Manager gt Select the NVR you would Alarm Push like to configure Alaren Cut 82 Mobile Connectivity 4 Tap MotionDetect then check each channel you would like to receive push notifications from Config Device Manager Channel Manager gt LocalAlarm 4 Alarm Push Ss MotionDetect Alarm Out Bii EE ORTE Favores B CAM 3 CameraMasking Local Files Conf Help rm ae e Check each channel you would like to receive push notifications from 9 Tap OK A test notification will be sent to your device After this whenever the selected cameras detect motion you will receive a notification NOTE You can see a list of notifications through the Event List menu To show the Event List then LZ menu from live view tap Tap on an event to view live video from the camera SERRE Device Manager Device Manager allows you to manage your NVR s To access Devic
52. e Camera Lock Motion Detection Recording Status Recording H 264 Compression 1080P 1920x1080 VGA 640x480 120fos 1080P Resolution Record Rate Bit Rate Record Mode 32Mbps High Quality Stream Sub Stream Recording Manual Schedule Motion Detection Record Interval Alarm 1 120 min default 60 min Pre record 1 30 sec Post record 10 300 sec 85 Appendix A System Specifications Video Detection and Alarm Trigger Events Video Detection Playback and Sync Playback Playback Function Backup Mode Configuration Backup Network Ethernet Network Function Max User Access Smart Phone IP Cameras Supported Storage SATA Ports Maximum Storage Capacity Dimensions Weight Package Dimensions Power Power Supply Recording PTZ Tour Alarm Video Push Email FTP Buzzer amp Screen tips Motion Detection Backup 1 4 4 Channel USB Device Network To USB Device RJ 45 port 10M 100M 1000M HTTP TCP IP IPv4 IPv6 UPNP RTSP UDP SMTP NTP DHCP DNS IP Filter PPPOE DDNS FTP Alarm Server IP Search 20 simultaneous users iPhone iPad Android FLIR Digimerge Panasonic Sony Dynacolor Samsung AXIS Arecont 2 internal SATA ports 2HDD external eSATA 4HDD 6TB 2 x 3TB internal 12TB 4 x 3TB external using eSATA 2 3kg 5 1lbs 100mm x 220mm x 146mm 3 9 x 8 7 x 5 7 W x H x D 1x 12V DC 5A for NVR 1x 48V DC 1A for PoE As our prod
53. e DDNS information into the NVR locally e Port forward the Client and HTTP ports default ports 80 and 35000 on the router To add a NVR using a DDNS address 1 Click Config Manager gt Device Manage Config Manager Scheme Task Config Record Plan Config Click Config Manager Alam Rec Config Emap Config WET User Manage Click Device Manage Device Manage Ext screen manage User Contig 42 2 3 ie P 43 Click Manual Add Click Manual Add Configure the following e Title Enter a name for your NVR of your choice e g home or office e Type Select NVR e Add Type Select Domain Name e Domain Name Enter the Domain Name from the confirmation email after your registered for DDNS followed by digimerge net e Port Enter the Client Port default 35000 e User Enter the NVR s user name default admin e Password Enter the NVR s password default 000000 Enter name of your choice NVR Type NVR y Select NVR Display Amount 1 Add type Q Single device Domainname Z ____________ Select Domain name Enter Domain Name followed by digimerge net Enter TCP Port default 35000 Domainname tomsmith digimerge net 35000 Enter User Name default admin ee Enter Password default 000000 q Click Add then click OK Click Device List Click next to No Group Double click the NVR DigiNet NVR Central Manageme
54. e Manager 1 From live view tap then fod 2 Tap Device Manager To delete an NVR 1 Tap the NVR to select it Alarn Message Metonbebeai 2014 03 25 10 37 24 mel n thiam histonin 2013 03 35 10 36 49 melan chana 1 MitionDeted 2013 07 25 10 36 22 mala MstlonDr a 2003 03 35 10 35 41 malan chams 1 Mationbeberi 2013 00 25 10 34 00 melin I Metenbenmet 2013 05 25 10 32 58 melan cham 1 Motion 2013 07 25 10 32 41 mlan charra 1 bonben 2013 07 33 10 32 39 mrlan anna 1 83 Mobile Connectivity 2 Tap a Tap OK to confirm Configuration Device Manager Tap to delete To modify an NVR 1 Tapan NVR to select 2 Tap the NVR again to open the edit screen 3 Update the connection details as needed and then tap Save 84 Appendix A System Specifications AA APPENDIX A SYSTEM SPECIFICATIONS System Main Processor Dual core embedded processor Operating System Pentaplex Operation Embedded LINUX Simultaneous View Record Playback Backup and Remote Monitoring Inputs Outputs 4 channel IP Camera Input Power over Ethernet 4 integrated PoE ports PoE Audio 1 channel input RCA 1 channel output RCA PTZ RS 485 supports Pelco D and Pelco P USB 3 ports 3 Channel Alarm Input 3 Channel Relay Out Display 1 HDMI 1 VGA 1920x1080 1280x1024 1280x720 1024x768 Interface Resolution Display Split OSD 1 4 Camera Title Tim
55. e NVR s Password default 000000 e Channel amount Enter the number of channels your NVR has 7 Tap Save 8 Tap ES 9 68 In landscape mode tap a channel and then select the camera you would like to view on the left OR In portrait mode tap on one of the display areas and select the camera you would like to open Click and then select a camera Mobile Connectivity DigiNet NVR HDInterface You can use DigiNet NVR HD in landscape or portrait mode EI PM Double tap to open in full screen Slide to select favorites Select different camera Disconnect all Snapshot Open menus Add current Change view to favorites display view Device Manager Device Manager allows you to manage your NVR s then gi To access Device Manager 1 From live view tap 2 Tap Device Manager To delete an NVR 1 Tap the NVR to select it 2 Tap S Tap Yes to confirm Configuration Device Manager cry Device Manager se E Ta p to d e lete Relay can Config To modify an NVR 1 Tap an NVR to select 2 Tap the NVR again to open the edit screen 3 Update the connection details as needed and then tap Save 69 Mobile Connectivity Using Playback Mode on Pad You can access recorded video on your NVR using your iPad NOTE You must enable Extra Stream Recording to use playback mode on mobile devices For details on enabling Extra Stream Recording see Recording on page 24
56. e Time Display Check to enable system time display e Channel Display Check to enable camera title display e Resolution Select the correct resolution for your monitor The system will reboot when you save changes e Image Enhance Check for the NVR to digitally improve the video quality on the live display This setting does not affect recordings e Enable Sequence Check to enable Sequence mode When Sequence mode is activated the system will cycle through enabled views and a arrows icon is shown on screen You can click this icon to pause Sequence mode NOTE View 1 View4 Check to enable views to be shown In Sequence mode View 1 allows you to enable disable specific channels in Sequence mode Other View 29 Using the Main Menu options allow you to enable disable views based on pages e Dwell Enter the Dwell time in seconds The Dwell time is the amount of time views are shown on screen before changing In Sequence mode 2 Click Save to save changes Default Als DEFAULT Please select setting entries that you want to default Select all a GENERAL SCHEDULE NETWORK Ei a m PAN TILT ZOOM DETECT a m m CHANNEL NAME DISPLAY DEVICE SEARCH Cancel The Default sub menu allows you to reset the system to factory default settings NOTE Resetting to factory defaults doesnot reset user accounts or passwords To reset the system to factory default settings 1 Check the settin
57. e following menus Scheme Task Config Record Plan Config Alarm Config Alarm Rec Config E Map Config DecCard Config User Manage Device Manage ExtScreen Manage User Config Using Alarm Rec Event Search Alarm Rec allows you to search for events saved on the NVR To use Alarm Rec 1 Click Alarm Rec eae 2 At the top of the screen select the alarm type you would like to search 45 3 Check Search Alarm Record Select alarm type Check Search Select NVR and channel Enter start and end time Click Search 4 Under Device select the NVR you would like to search 9 Under Start Time and End Time enter the start and end times for your search 6 Click Search A list of relevant alarms appears below Using Playback Mode You can view recorded footage from your NVR s in the CMS software To use playback mode 1 Click Playback 2 Under Device select the NVR and channel you would like to search Select Channel Select NVR Select search parameters Click Search e Check Multiple channel to playback video from multiple cameras Select camera and then click Add Repeat to add additional cameras 3 Under Parameter select the start and end time for the search 4 Click Search 46 DigiNet NVR Central Management Software 9 Check video files to select and click Play to open OR click Download to download the video files to the local computer
58. e is no picture on selected channels camera picture is not being displayed e Remote control is not detected by the system Possible Causes e Cable from power adapter is loose or is unplugged e Cables are connected but NVR unit is not receiving sufficient power e PoE power adapter is not connected e Camera cables are loose or have become disconnected e Camera NVR connection to LAN has become interrupted e Batteries in the remote control are drained e There are no batteries in the remote control Solutions e Confirm that all cables are connected correctly e Confirm that the power adapter is securely connected to the back of the unit e Confirm that the unit is powered on LED indicators on the front should be ON e f the unit is connected through a power bar or surge protector try bypassing the bar and connecting the power directly to the wall outlet e Confirm that there is power at the outlet e Connecting the power cable to another outlet e Test the outlet with another plugged device such as an electric calculator or phone charger e Make sure the 48V DC power adapter Is connected to the NVR or the cameras will not receive power from the PoE Ports e Disconnect and reconnect the cable at the NVR and atthe Camera e Try moving the camera to another channel or use another cable e f your cameras are not using PoE make sure they are using the correct power source according to the specifica
59. e product requires these extra ports you may enter them here 4 Under IP enter the IP address of your device NOTE The IP is usually found in the information window of your NVR 5 Under Port enter the NVR s HTTP Port by default port 80 6 Under 2nd Port enter the NVR s Client Port by default port 35000 7 Click Next to continue 93 Appendix C Auto Port Forwarding Wizard Step 3 Update the Router Settings 1 Click the Update Router button e You will see your router window open The Auto Port Forwarding Wizard automatically populates your router with the relevant information This will take a few moments DIGIMERGE Righi for Business Amo Pon Forsaading gt Peram bu Yos ae ne Sy done M n a Undate Router button on sn ce did he Leet Duis buire pras do sE open ee A A Poms sh ndd ae ar pl ere Ba perce A read poe cy Lie Bee be ined Ep ne ret Haring Irae mii Ves peer ge ae Lal epee al 2 Close the update window when the update finishes Step 4 Test your Connection 1 Click the Test Your Connection button e Your system s default browser opens and connects to your device NOTE Ensure that Internet Explorer is your system s default internet browser NOTE A window opens that prompts you to enter in your NVR s user name and password do not enter your DDNS log in information NOTE ActiveX warnings may appear Accept all ActiveX installation warnings to connect to your s
60. ecording 1 Under Channel select the camera you would like to configure or select All 2 Under PreRecord select the duration for pre recording 3 Check Mirroring to enable mirror recording for the selected channel 4 Click OK to save settings Configuring Holidays Holiday settings allow you to configure a special recording schedule on certain days To configure holidays 1 Check the checkbox next to Holidays Setting to enable holidays 2 Click Holidays Setting 03 08 2013 v 12013 Cancel Using the Main Menu 3 Click days in the calendar to enable them as holidays Selected holidays are highlighted in blue 4 Click OK Click OK to save changes Network NETWORK SETTING Detauh The Network sub menu allows you to configure network settings Configuring DHCP or Fixed IP Address 1 From live view right click and select Main Menu Login if prompted 2 Click Setting gt Network 3 Check DHCP to use DHCP or un check to use a Static IP address If you un check DHCP configure the following e IP Address e Subnet Mask e Gateway e Preferred DNS e Alternate DNS 4 Click Save to save your changes Restart the system to update the IP address Configuring System Ports The system uses the following ports e TCP Port Client Port Used for remote video streaming to computers and mobile devices The default port number is 35000 29 Using the Main Menu e HTTP Port Used to enable
61. evice After this whenever the selected cameras detect motion you will recelve a notification NOTE You can see a list of notifications through the Event List menu To show the Event List menu tap Add and check Event List Return to the Main Menu and select Event List Tap on events to view live video from the camera Event List Tap to view Motion Detect f d T 2013 03 25 09 17 13 Ive VIGeO nvrlan Channel 1 Device Manager You can use Device List to manage your NVR s To access Device List e From the Main Menu tap Device Manager To edit an NVR 1 Tap the NVR in Device Manager 2 Edit the connection details as needed 3 Tap Save To delete an NVR 1 Swipe the NVR you would like to delete to the right 2 Tap Delete Tap OK to confirm Device Manager als nvr Tap Delete Android Tablets DigiNet NVR HD is an app that allows you to remotely view your NVR on an Android tablet System Requirements e Android 3 3 or later Prerequisites e Port 80 and 35000 or your HTTP and Client Ports if you have changed them must be port forwarded on your router to your NVR s IP address e You must create a DDNS account and have the DDNS settings configured in your NVR e The NVR must have Internet access e You must have a DDNS address to log in remotely 78 Mobile Connectivity Connecting to your NVR on an Android Tablet 1 Install DigiNet NVR HD for free from the Google Play Store
62. fig Set to ON 3 nv OFF 69 Mobile Connectivity 3 Tap Motion Detect and then check each channel you would like to receive push notifications from nvrian Period 365 days Push type PlayBack v ES Motion Detect Sa eer CAM 2 CAM 3 9 CAM 4 4 Tap OK A test notification will be sent to your device After this whenever the selected cameras detect motion you will recelve a notification NOTE You can see a list of notifications through the Event List menu To show the Event List menu tap Add and check Event List Return to the Main Menu and select Event List Tap on events to view live video from the camera Event List jin Tap to view Motion Detect 2013 03 25 09 17 13 4 live video inyrlan Channel 1 Device Manager You can use Device List to manage your NVR s To access Device List e From the Main Menu tap Device Manager To edit an NVR 1 Tap the NVR in Device Manager 2 Edit the connection details as needed 3 Tap Save To delete an NVR 1 Swipe right on the NVR you would like to delete z Device Manager Add SS Demo pen Swipe right on the NVR you would like to delete and tap delete s NVR 2 Tap Delete Tap OK to confirm 66 Mobile Connectivity iPad DigiNet NVR HD is an Pad app that allows you to remotely view your NVR System Requirements e iOS 4 3 or later Prerequisites e Port 80 and 35000 or your HTTP and Client P
63. g Motion Detection Events iniciada tad wea dene as dnote w tee ee hedwe Pa Rt ds Let Ges 28 TTS OOTY erae Ger ote A a a E SA 29 OGU sce DEA ARA a aa aa Mir AAA AAA IAE A 30 Device Sear Circa oa si y ia A ad 30 Adding Cameras from the LAN it A ils eR EAS BS AAA ADA AA 30 Mantal Ada ts ek ae Bai Rok i Aa tee ah a es o ined ahi Se al aha ait es 31 PONG Cameras 22 eis Bob eit kept ee he Mane Bolas sou AB A Eo eee See es 31 BTCV TEN G40 Cambra o E dl dia edo 31 POVANCEO tive eect eee a a a aE N eE eno 32 ROMINA CON eene A AAA A SARA ante ne A ea 32 Formating Hard DVS ia a a a A AS AS 32 DEVE CUING Hara Drive TIMES esc AA AEREA AA RAS 32 Configuring Hard Drive Group Settings 0 0 0 a e ad o db 32 Configuring eSATA External Hard Drives oooocooooooor eee e eens 33 AE ata cress vag shah E 18 Bac ante Se asl Baa aac ay ps Se ke Seema tis NS DR edad ind BAe 394 RACOT ss E A A AS RA AI A E A nc one 34 A COO T e ease tae int ep ras A a ar aac a E E A tirana at he dog a E ae E JI Adano A CIUM E ee r aer ta n E td or a aa 35 Moda ACCOUN S ua st ati ida ia a 36 Mara A ae eee ae Se eee eee eae Se eee e Te a A E eee See a a ee ore eee 36 Adding CEOUDS rad ds Sowa Gaga ae tw Ae wh Gama ee dae ees 36 Deleting GROUNDS ori bora ra bobina astute Gem co in da Betws alas Hn aha aaa eens 37 Modin TROUT Sz 85 sera sao se See toch A id ea a eat 37 AU OMIMAN al ASAS AE AE EA A er eee ae AA AAA 3 7 COTON qe AA O eae ae R eee Se Pee eto Shae E ae eae 3 7 SIMUL OW
64. g disk 2 65 Shul down at 03 07 13 122062 we Reboot wilh Hag 901 35 Disk totals lt D Current working disk 2 1 21 55 User logged in admin gt Ade sersqwe gt 14 Page Up Page Down Backup Clear FrePage MextPage Curam Page Total Page Jump tor 7 GO The Log sub menu allows you to search for system logs To search for system logs 1 Under Type select the log type to search for 2 Under Start Time and End Time select the start and end time for your search 3 Click Search 4 Optional Click Backup to export logs to a USB flash drive connected to the system Version e VERSION Channels 16 Alarm In 16 Alarm Out 3 System 2 610 GM00 0 Build Date 03 06 2013 Web ZE INTATZ Serial No PA2FF00300856 h UPGRADE lf you need to upgrade system now please insert USB upgrade disk then press the start button to start upgrade Don t shut down the power during upgrade The Version sub menu allows you to view information about the current firmware You may also update the firmware through the version menu Updating Firmware 1 Download the latest firmware update from 21 Using the Main Menu 2 Copy the firmware to a blank USB flash drive NOTE Do not have any folders on the USB flash drive just the firmware file 3 Connect the USB flash drive to a USB port on the system 4 Right click and then select Main Menu gt Info gt Version 9 Click Start to update firmware Wait f
65. gn all devices Load decode card when system boots up D Auta start record plan F duo pop up alarm infomation disks T Auto login FUR SynaolP Mt CMS F Auto run FUR SyncralP MVR CMS vaher Hot Rey Setup Resalta monitor window a Cut z Auto register senor listening port 33330 Displayed items ln right bor Deren l Preview Picture 4 System default open mode Daphny alare item in interfaces External Alarm Motion Detect Get al devices running status Record basic setup Snapshot picture path APUR Simral NVR OMS IP ia Dester free minimum capacity Me 2000 Picture Pie Name Fade RECTE Cra 2H ibero for m Record Tmefurutel 5 Recorded fle path C PUR SmorolF HAL OMG Record Rerennd File Name Rules RECTO dr MD masa 01D ona E Tnenioaded record fle name nie RECIFE AHMA HOHH Amas Devin oa Siuta shart monitor seiu Auto Start Projecte Tes Mo Auto Start Task Yes Mo Tok ceive HO Save last monitor stalus Syme timo seee mo sm PC me to device Syne Time becomes wakdal 3 00 00 E luto reboot device Werk Sun Mon Ties ed CA Fr Alarm record basic seip Alarm record m x amount PP Reheshinteva 10 Sec a FUs pop up wink bo display the alarm video Alarm video window amount a Add disarming alarm message to the slam record a Misreinfonmason output porti ugg e Verify password Check to require passwords when logging into or closing the CMS e Log in all devices
66. gs you would like to reset to default settings 2 Click OK 30 Bio 2 alah e Device Search The Device Search menu allows you to manage connections to your IP cameras SyncrolP cameras connected to the PoE Power over Ethernet Ports will automatically be detected by your NVR Device Search also allows you to search for IP cameras connected to the LAN Some configuration may be required to connect IP cameras from other manufacturers NOTE For a list of 3rd party IP cameras supported visit www digimerge com Adding Cameras from the LAN 1 Connect the camera to a router or switch on the same network as the NVR 2 Right click and select Device Search Log in using the admin account the default User Name is admin and the default Password is 000000 3 Click IP Search The NVR scans your LAN for compatible IP cameras CheckIP Search Marval Ackd 4 Check the camerals you would like to add and click Add gt Check cameras Click Add 9 Ifthe Status indicator is green the camera is connected and no further configuration is required Click OK to save changes 6 Ifthe Status indicator is red click PMA Update the following information as needed A Channel 1 Manufacturer Onvif IP Address 10 10 6 86 RTSP Port 554 User admin Password 200000 HTTP Port 8090 Remote Channel 1 Decoder Buffer 280 Auto TEP UDP amp conf_net muticast Cancel e Manufacture
67. h User Name default admin e Password Enter the NVR s Ghanas b Password default 000000 wii 28 e Channel Enter the number of l channels your NVR has E A 7 Tap Save 8 Tap re 9 Tap Live Preview Enter the password Enter the number of channels 10 Tap on one of the display areas and select the camera you would like to open in the selected display area Live Preview Tap and select a camera 11 Repeat to view additional cameras 62 Mobile Connectivity DigiNet NVR Interface You can use DigiNet NVR in portrait and landscape mode Return to Main Menu_ amp Live Preview Double tap to opena channel in full screen Disconnect from camera Snapshot Connect to camera fo fe Gx al Change Camera Connectto all previously added to EF Ea cameras Hieconnscrall i eee Start stop manual record 2 gt sr ea Access Favorites ine l l Open image settings Viewing Videos with Local File If you have saved videos using DigiNet NVR you may open them with Local File NOTE You may open screenshots using the Photos app To access Local File e From the Main Menu tap Local File Return to Main Menu Delete all files Tap files to open 63 Mobile Connectivity Using Playback Mode on Phone You can access recorded video on your NVR using your Phone NOTE You must enable Extra Stream Recording to use playback mode on mobile
68. hat will be taken when errors occur e Show Message Check to show pop up window with information related to the error e Send Email Check to enable email message You must configure email alerts before you will be able to receive them e Buzzer Check to enable system buzzer 4 Click Save to save changes Record ES RECORD Record Mode All 12 3 4 Schedule B Manual Stop Schedule Manual Stop Cancel The Record menu is used control manual recording for connected cameras The Record menu is divided into the following sections e he Record Mode section defines settings for the main high quality recording stream e The Extra Stream section defines settings for an optional lower quality recording stream This is useful because you can record the Extra Stream to the hard drive and stream it for playback to remote devices This saves bandwidth during remote playback NOTE Enabling Extra Stream Recording is required to use playback mode on a smartphone or tablet NOTE Recording the Extra Stream will increase the amount of disk space required for recording To configure manual recording 1 Right click in live view and select Record Log in if prompted OR Click Main Menu gt Advanced Record Log in if prompted 2 Under Record Mode select the main stream recording option under each camera or under All to configure all cameras e Schedule Camera will record according to setti
69. idelines in this manual to avoid improper usage which may result in damage to the unit electrical shock and fire hazard injury In order to improve the feature functions and quality of this product the specifications are subject to change without notice from time to time www digimerge com iii Features piemen GE e Easy Connection and setup with 4 integrated PoE ports and auto discovery of IP Cameras e Record all 4 cameras in Real Time at 1080P Full HD quality e Full HD 1080P recording provides the most detailed picture and reliable identification with selectable area digital zoom e Dual streaming H 264 and dual core processor Pentaplex operation simultaneous View Record Playback Backup amp Remote Monitoring ONVIF 2 0 conformance ensures compatibility with popular industry IP cameras Substream recording for bandwidth efficient remote playback 64 Channel CMS by Digimerge included Fully PC Mac compatible Mobile apps iPhone iPad Android HDMI VGA simultaneous video output Free DDNS service by Digimerge with secure redundant servers RS 485 supports PelcoD amp P PTZ Audio 1 0 1 in 1 out Alarm 0 Supports 2x SATA HDDs up to 3TB 6T8B total 2x USB 2 0 ports e eSATA back up storage up to 4 HDD 12TB total e Drive Mirroring e Embedded Linux operating system simple GUI on screen display e 1 3 5 year Fortress Vision warranty Please visit www digimerge com for information firmware and compatib
70. ility updates for mobile viewing iv TABLE OF CONTENTS ala o Started oat cx PA rn id ee ate dt aan ese 1 Basic SetUD sar A GA ee ee A ee ees 2 CONECTO Caller aS sk ei 8 A A A BE Mais Be ee BEES Ba Pe Bo whe Z ZNCOMMCCT AION GOL di ii a dto dades Z 3 Connect the MOUSE 0 A AREA AAA a EAS Ad ANA AA AA 2 A CONOC WIC ENGINE CINO sarri cue he E TA AA A A io e hl 2 I Connect he Fower Adaptors ote brida a AAA es 2 a A 201500460 a a a a a a A A 3 Real E MEGa anr ansera a cde R E E AA 4 Remote Controlisiaarisicada tc Aa 5 MOUSE CONTROL va AO E Ree ae 6 USING the Syste iria rd ios 7 PASSWORD ie Me 7 On Screen DISPlay cor at EA A A eee wae AR 7 Using the QUICK Men 2 2 iban a db ds 8 AGJUSUNOG COLORS CLINGS AA AA A ae eee ada Sete 8 Using the Navigation Bal eosin iras aria 9 Using the Camera Toolbar ui cds 9 USINO QUICK F IIVO K Ls UNA ee AAA AE NADA T A ER O ee 10 USING VIG al ZOOM IN LIVE DIS Play sui drid a A A AA 10 Using Real time Backup er ata trig shea e ii lo A E e aoe ie aida 10 Using the VirtGau KeyDoard suscita inde ba dis 11 Setting the TMG ivi ia da ae eee ae eee es 12 A bases ware een ean a beeen ate EA 13 Search Pld bdC kc osease cate 14 Playing Back Video from the Hard Drive 0 00 cece eee es 14 Playback CONTFOLS arras 15 DaCKUD iia reido aia es 16 F ormalling Ne USP DECE Ay AA id AAA eh eee a E ai 16 BACK UBWIOCOS LEIA Rik DARTE IAE ASA AAA Ad 16 USNO Vdeo CUD BACKUD e resne eRe i A E a A ees e iia E da een 17
71. it mode Double tap to open in full screen Slide to select favorites Select different camera Disconnect selected channel Snapshot Open configuration menu Add current Change view to favorites display view 80 Mobile Connectivity Using Playback Mode on Android Tablets You can access recorded video on your NVR using your Android tablet NOTE You must enable Extra Stream Recording to use playback mode on mobile devices For details on enabling Extra Stream Recording see Recording on page 24 To use Playback Mode 1 From Live View tap then Q 2 In Portrait Mode Tap select the start time and end time for your search and select the camera you would like to playback OR In Landscape Mode Select the start time and end time for your search and select the camera you would like to payaa Select start time Q Select end time Select camera 3 Use the playback controls BOMin Next file Pause play Previous file NOTE Playback controls are only shown in portrait mode 81 Mobile Connectivity Enabling Push Notifications You can have the app send push notifications to the notifications area on your device when one of your cameras detects motion Once you have received a push notification you can select it to open live video from the camera that detected motion DEZ Monday Marh 25 2013 T lab qs Settings Ongoing 1 y Connected as a media devic
72. ld Password enter the account s previous password 4 Under New Password enter the new password for the account Repeat it under Confirm 5 Click Save Deleting Accounts 1 Click the account in the list 2 Click Modify User 3 Under User select the account you would like to delete 4 Click Delete then click OK to confirm Adding Groups Groups allow you to easily manage permissions for multiple user accounts A user account by default has all permissions available to the group it is in and it cannot be given permissions the group does not have To add a group 1 Click Add Group cy ACCOUNT 3 User Group Status l admin admin Login Local default user Default User qwe admin Login Net R Add User Modify User Add Group Modify Group Modify Password Click Add Group 2 Under Name enter a name for the group 3 Optional under Memo enter comments for the group 4 Configure group permissions as needed Note that any user accounts added to the group may not be given any permissions that are not selected Enter group name Select permissions 5 Click Save Deleting Groups 1 Click Modify Group 2 Under Group select the user group you would like to delete 3 Click Delete and then click OK to confirm Modifying Groups 1 Click Modify Group 2 Under Group select the user group you would like to modify 3 Update group settings as needed and then click Sav
73. le ATTENTION For security it is highly recommended to keep Continuous Recording ON at all times 108 Troubleshooting Remote Connectivity Troubleshooting Possible Causes Solutions e Cannot connect to e Ports not forwarded e Port forward the HTTP port default 80 and Client the NVR over the port default 35000 Internet e DDNS Setup not completed e Register for a DDNS account For details see Appendix D Setting Up DDNS Service on page 97 e Ports are blocked by Internet e Some ISP s block port 80 Reassign the HTTP port Service Provider ISP to anything above 1026 Re complete port forwarding using the newly assigned port e Multiple routers installed in e If you have multiple routers additional setup may local network be required For details see Configuring Multiple Routers on page 94 e Could connect to e NVR internal IP address has e This can occur if your router resets due to power system previously changed failure Set up a fixed IP address for your NVR For but no longer can details see Configuring DHCP or Fixed IP Address on page 25 e Cannot connect to e IP address used from outside e Use the DDNS address to connect to the NVR the NVR using a local network using a mobile application e g smartphone or tablet tomsmtih digimerge net e Router is blocking DDNS e Turn off WiFi connection and attempt to connect connection from internal network using 3G or mobile network 109 Dic i
74. ll cabling wiring from the system 2 Pull up on the hard drive door latch to unlock the hard drive compartment Hard drive door latch 3 Pull the hard drive compartment out of the system 4 Place the hard drive upside down on a surface 103 Appendix F Hard Drive Installation 9 Place the hard drive compartment over the hard drive with the door facing away from the SATA connectors Insert hard drive screws x4 to secure the hard drive to the hard drive compartment Door SATA connectors 6 Hold the hard drive and compartment in a vertical position with the SATA connectors near the bottom of the unit and fully insert it into the system SATA Connectors 7 Push the hard drive door latch in to lock the hard drive in place NOTE After installation you must format the hard drive in order to use it with the system See Formatting the Hard Drive on page 106 Removing the Hard Drive A Make sure that the system is OFF and ALL power adapters have been disconnected before removing installing the hard drive 104 Appendix F Hard Drive Installation To remove the hard drive 1 Power off the system and unplug all cabling wiring 2 Pull up on the hard drive door latch to unlock the hard drive compartment Hard drive door latch 3 Pull the hard drive compartment out of the system 4 Place the hard drive and hard drive compartment upside down on a surface Remove the hard drive screw
75. m must be port forwarded on your router to your NVR s IP address e You must create a DDNS account and have the DDNS settings configured in your NVR e The NVR must have Internet access e You must have a DDNS address to log in remotely Connecting to your NVR on an Android Phone 1 Download DigiNet NVR for free from the Google Play Store 2 Tap onthe DigiNet NVR icon a to start the app 3 Tap wr 72 Mobile Connectivity 4 Tap Device Manager Device Manager e Preyveew Device Manageri e ee Help Add 9 Tap Add gt Manually Add Device Manager Tap Add 6 Configure the following e Name Enter a name for your NVR of your choice e Address Enter your DDNS i ana Oa N omsmit address e g Su tomsmith digimerge net Address tomsmith digimerge net val the DDNS address e Port Enter the Client Port default 35000 Port Enter the Client Port e Username Enter the NVR s Username admin Enter the user name User Name default admin Password Enter the password e Password Enter the NVR s Password default 000000 Channel 4 Enter the number of channels e Channel Enter the number of id Close odify channels your NVR has 7 Tap Save 8 Tap ma 9 Tap Live Preview 73 Mobile Connectivity 10 Tap on one of the display areas and select the camera you would like to open in selected display area Live Preview Tap and select a camera 11
76. me Home Picture Title Home Picture Path CAPROGRA AFLIRSY limapsi0_1_1 JPG Click Browse to select a Jpg image Browse 6 Click OK 90 7 Click Pic Click and drag picture tothe window Click Pic 8 Click and drag the picture to the window to use It for the E Map 9 Click Device to view a list of connected NVR s 10 Click next to an NVR To place cameras drag cameras from the list to the map Dragcamerasto SST lara Channel Alar Channel i Nam Channel Alarma Channel E Aare Chanel Alone ChannelF i Aare Channel Alar Channelt Aare Channeli Alar Channel R Agr Channel iB Alar Channel oh Eme Device Pie Click Click Device 11 Click Save NOTE To delete all E Map data including images and camera positions click Clear E Map Opening Cameras from E Map Once you have configured your E Map you can use it to open cameras in live display To open cameras from E Map 1 Click E Map 51 2 Click on a display area in the main CMS window then double click on the camera to open it Click a display area Configuring the CMS You can configure settings for the CMS such as the admin password recording directories and start up settings through the Config menu Configuring CMS Options 1 Click Config gt Options 2 Configure the following Spelem baer seba Languages Enieh E Ll al verify password to
77. mware upgrade over the LAN 1 Download the Config Tool from www digimerge com 2 Extract the contents into a folder 3 Open the folder and right click ConfigTool exe and Run as administrator If a Windows Firewall warning appears click Allow Access The Config Tool scans your LAN for NVR s 4 Click Upgrade Tap Tea cem click legin button directly and them input correxpanding information to lagia Click Upgrade Hr t gt lr ads Ketresh Login Lagrat 9 Check any NVR s you would like to upgrade 6 Click Open Select the upgrade firmware file bin 100 Appendix E Remote Firmware Upgrade Click Upgrade Wait for the upgrade to complete Do not power off the system or disconnect the power cable during upgrade The system will restart when the upgrade is complete Configas n Diarios List IP Aakres Port Mac Addrets Lpgrade Stat Remari T wong VSO giaa 7 Ya ibid 15000 Witteni Check NVR s Click Open and select firmware file po e A E LW 2an Iean Click Upgrade Installing a Firmware Upgrade Over the Internet Prerequisites e Port forward the Client Port default 35000 on the NVR s local router e Obtain the public IP address of the NVR e Download a firmware upgrade from www digimerge com If one Is available Extract the contents To perform a firmware upgrade over the Internet a a Download the Config Tool from www digimerge
78. ngs configured in the schedule e Manual When selected the camera will use continuous recording e Stop When selected the camera will not record 3 Under Extra Stream configure recording options for the Extra Stream 4 Click OK to save changes Account wx ACCOUNT Status admin i Login Local default Default User qwe i Login Net r Add User Modify User Add Group Modify Group Modify Password The Account sub menu allows you to configure user accounts Accounts are organized into groups and receive permission to access system functions based on their group s Using the Main Menu settings By default the following user groups are configured on the system e admin Accounts in the admin group are system administrators They have full access to the system may configure all system settings and can manage user accounts e user Accounts in the user group are normal users They have limited access to system menus Adding Accounts 1 Click Add User Add User User Reuseable Password Confirm Memo Group admin 63 Authority v Control Panel v Shutdown the Device v Monitor y Monitor_CHO01 Y Monitor_CH02 v Monitor_CHO03 Y Monitor_CH04 9 Y Monitor_CH06 10 v Monitor_CH07 15 g Mianiar lC 4 Page Up Page Down Enable Disable Authority Save Cancel 2 Configure the following e User Enter a user name for the account e Memo Optional Enter comments f
79. ning or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Conditions Requiring Service Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e f liquid has been spilled or objects have fallen into the video product e f the video product has been exposed to rain or water e f the video product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation e f the video product has been dropped or the cabinet has been damaged e When the video product exhibits a distinct change in performance This indicates a need for service Replacement Parts When replacement parts are required have the service technician verify that the replacements used have the same safety characteristics as the original parts Use of replacements specified by the video product manufacturer can prevent fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks recommended by the manufacturer
80. nt Software 8 Click and drag the NVR to the display area to view FLIR SyncrolP NVR CMS V4 06 CMS Live Viewing Overview Click Device List Click Double click the NVR FLIR SyncrolP NVR CMS V4 06 7 Cm y Y 1 Camera Controls Change display mode Snapshot FQ ee G pa a Digital Zoom Manual Click and drag record 44 Disconnect OOOO m No group lt ay a EXt screen manag PTZ Direction 2 DigiNet NVR Central Management Software 2 Live View Toolbar BH Gol ie 25 Select image Full screen quality Latency Display views Fluency 3 CMS Quick Menus Click to access key CMS and NVR functions such as Playback event search Alarm Rec E Map and software configuration Config 4 CMS Window Controls Lock CMS Full Menu Maximize Quit Restore Minimize 9 Device List Open NVR s and IP cameras in live display e Click next to NVR s or Groups to expand m Groupi e Click and drag NVR s Groups or Cameras to the display area to open P A NS j e Right click NVR s Groups or Cameras to view system options z a 6 CMS Menus cam e PTZ Direction Access basic PTZ controls E ESAS e PTZ Advanced Access advanced PTZ controls e g Auto Scan Tour etc gt e Tools Contains the following menus Begin Record Plan NVD Control Health Report Log Search Alarm Video Alarm Output Color Config Volume e Config Manager Contains th
81. o select Format 32 4 Click Apply Click OK to confirm Wait for the hard drive to format Hard drives become Read Write hard drives by default when formatted HDD Management Alarm Set HDD Setting Alarm Release HDD Channel rk HDD No Setto Read Write 7 Execute Type Status Capacity Record Time Select HDD Select Format Click Execute Selecting Hard Drive Types The system supports the following hard drive types e Read Write Normal recording hard drive e Read only Do not record on the hard drive e Mirroring Recordin parallelto Read Write hard drive for cameras enabled for mirroring This allows you to create automatic backups of recordings NOTE Mirroring must be enabled in the schedule for details see Schedule on page 24 NOTE Mirroring begins backing up data Starting when the hard drive is configured for mirroring To select hard drive types 1 Under HDD No select the hard drive you would like to format 2 Under Set to select the hard drive type 3 Click Execute 4 Right click to exit the HDD Management menu The system will restart Configuring Hard Drive Group Settings Hard drive group settings allows you to balance recordings for your IP cameras across multiple hard drives To configure hard drive group settings 1 Click HDD Setting 2 Under HDD Group select the group number you would like to assign to each hard drive HDD Setting HDD No HDD
82. of business hours Click OK when finished NOTE This setting can override scheduled motion recording This means that motion recording will only take place at times that are enabled both in the Schedule menu and here Configure the following system actions when motion is detected e Show Message Check to enable an on screen pop up On screen pop up shows the channels an event occurred on and the type of event e Send Email Check to enable email alerts You must configure email alerts before you will be able to receive them see Configuring Email Alerts on page 27 e Record Channel Select the channels that will record when motion is detected on the selected channel e Buzzer Check to enable the system buzzer e Snapshot Unsupported 9 Click Save to save changes Using the Main Menu DISPLAY Channel Name Channel Display E Transparency Time Display R v Image Enhance a Resolution 1280x1024 Enable Sequence Dwell 5 All a View 1 View 4 Motion Sequence Type View 1 v Alarm Sequence Type View 1 Default Save Cancel The Display sub menu allows you to configure the system s display settings such as the monitor resolution To configure display settings 1 Configure the following as needed e Transparency Select the menu transparency between 128 lowest and 255 highest e Channel Name Click Modify and enter names for your IP cameras Click Save when finished
83. on the internal network needs to send or receive information from a system outside the network i e from the Internet the information is sent to the router 88 Appendix B Setting up Remote Viewing NETWORK EXAMPLE Router Router PC Internal IP 192 168 0 2 External IP Internal IP 216 13 154 34 192 168 0 1 NVR Internal IP 192 168 0 3 Internet Internal Network When a computer on the Internet needs to send data to your internal network it sends this data to the external IP address of the Router The Router then needs to decide where this data Is to be sent to This is where setting up Port Forwarding becomes Important Port Forwarding tells the router which device on the internal network to send the data to When you set up port forwarding on your Router It takes the data from the external IP address port number and sends that data to an internal IP address port number i e Router External IP 216 13 154 34 to NVR Internal IP 192 168 0 3 80 Please see resources available at http www digimerge com for more assistance with port forwarding 89 Appendix C Auto Port Forwarding Wizard AAA APPENDIX C AUTO PORT FORWARDING WIZARD The Auto Port Forwarding Wizard is an exclusive software that easily automates router port forwarding Before setting up a DDNS account it is recommended to run the Auto Port Forwarding Wizard to port forward the required ports Installation To install the Auto Port Forwarding Wi
84. or the firmware upgrade to complete Do not remove the USB flash drive until the upgrade process is complete or power off the NVR during the upgrade process Online Users ay ONLINE USERS ser Name None The Online Users sub menu shows a list of users connected to the system using remote devices You may Disconnect a user for upto 18 hours or Block a user from the system Remote Device Info The Remote Device Info sub menu shows information about IP cameras connected to the system It contains the following tabs 22 e Channel Status Shows the IP address model number and camera status Status IP Address Video Loss Camera Mask Alar in 10 42 2 61 e Connection Log Search for camera status logs including user access to cameras Channel AN Stan Time 2012 05 03 00 00 00 End Time 2012 05 04 00 00 Channel e Net Load Shows a graph of upload and download traffic for your system Setting The Setting menu allows you to configure general system schedule network recording display and motion settings lt also allows you to restore the system to factory defaults General LA GENERAL System Time 03 07 2013 13 29 56 Date Format MM DD YYYY MM DST Set DECRECE ECON e h v Time Format 24 HOUR Language ENGLISH z HDD Full Overwrite Video Standard NTSC Pack Duration 30 Device No 8 Realtime Play 5 Mouse Property MouseSet Startup Wizard Auto Logout 5 N
85. or the account e Password Enter a password for the account Repeat password under Confirm e Reusable Check to enable multiple users to connect using this account e Group Select the group that the account will be included in 3 In the bottom portion of the screen select the permissions that will apply to the user By default the account will have all permissions that are enabled for its group An account cannot have more permissions than its group 4 Click Save to save changes 30 Using the Main Menu Modifying Accounts Admin accounts may modify the user name password and permissions of user accounts User accounts may modify their own password To modify account settings 1 Click the account in the list 2 Click Modify User ACCOUNT Group Status admin Login Local user Default User admin Login Net R Add User Modify User Add Group Modilf Group Modify Password Click Modify User 3 Under User select the account you would like to modify 4 Configure the account settings and permissions as necessary and then click Save To modify an account password 1 Click Modify Password ACCOUNT 3 User Group Status 1 jadmin admin Login Local 2 default user Default User 3 qwe admin Login Net hs Add User Modify User Add Group Modify Group Modify Password Click Modify Password 36 2 Under User select the account you would like to modify 3 Under O
86. orts if you have changed them must be port forwarded on your router to your NVR s IP address e You must create a DDNS account and have the DDNS settings configured in your NVR e The NVR must have internet access e You must have a DDNS address to log in remotely NOTE You will need to create an iTunes account before you can download the app An lunes store account requires a valid credit card number The app Is free of charge Connecting to your NVR on an Pad 1 Install DigiNet NVR HD for free from the App Store 2 Taponthe DigiNet NVR HD icon B to start the app 3 Tap ES then gl 4 Tap Device Manager 5 22 PM Configuration Device Manager Tap Add Device Manager Relay out Config Favorites Local Config Help 9 Tap Add 67 Mobile Connectivity 6 Configure the following 10 56 AM Not Charging H_ Configuration Cancel New Device Save Device Manager Enter a name for your NVR Relay out Config Mama NVR a Address tomsmith digimerge net Enter the DDNS address Favorites Port 35000 Enter the Client Port Local Config User Name admin Enter the user name Help Password eeeee Enter the password Channel amount 4 Enter the number of channels e Name Enter a name for your NVR of your choice e Address Enter your DDNS address e g tomsmith digimerge net e Port Enter the Client Port default 35000 e Username Enter the NVR s User Name default admin e Password Enter th
87. ou to save footage from the live display to a USB flash drive not included or external hard drive not included To 1 2 use Real time Backup Insert the USB flash drive or external hard drive into one of the USB ports on the system Move your mouse to the top of the channel display and click T to start Real time Backup The icon changes to H Click again to end Real time Backup The file is saved to your USB device NOTE If the system prompts you to log in you will need to click again to start Real time Backup after logging in Using the System Using the Virtual Keyboard The Virtual Keyboard is used to input text or numeric values in certain menus Backspace Enter capital letters Confirm entry Setting the Time AA SETTING THE TIME recording It is highly recommended to set the time on the system prior to doing any To set the date and time 1 Inthe main viewing mode right click and click Main Menu Log into the system using the admin account default User Name is admin and Password is 000000 2 Click Setting gt General 3 Enter the current date MM DD YYYY and time HH MM SS under System Time GENERAL Set the date and time System Time 03 07 2013 13 29 56 __ __ gt Click Save Date Format MM DD YYYY 7 DST Set DECRECE aaa e v Time Format 24 HOUR y Rh Language ENGLISH HDD Full Overwrite Z Video Standard NTSC Pack Duration 130 Device No 8 Realtime Play 5 Mo
88. owing e Window Select the display window you would like to configure e Device Click and drag the camera from the Device List in the main CMS window to the field to add it e Stream Type Select Main Stream or Extra Stream to view the sub stream Task Edit a Group 1 NVR T Monitor Item J can Enter Task name OR Stay time s e Select split screen layout Window ro cc z se E Monitor These CAM 3 Select display window aca CAM 4 Drag camera from Device m Alarm Ou Device List Channel E a Ext screen manag Stay time s 10 ma Select Main St Preset NJA A elec ain ream extension si or Extra Stream StreamType Main Steam y si cia Click Add Delete up Down ok Cancel Tips Please drag the channel from the device list in the main interface to the device or channel column of current monitor interface 7 Click Add Repeat Steps 6 7 to configure additional screens 8 Click OK Click OK to save changes Configuring Projects Once you have multiple tasks set up you can configure projects to automatically cycle through them To configure a project 48 DigiNet NVR Central Management Software 1 Click Config Manager gt Scheme Task Config 2 Click Monitor Project Click Monitor Project 3 Click New Enter a Name for the project You may not change the name after the project is created 9 Under Mode select Tour Mode or Schedule Mode Tour Mode will cycle through tasks ona
89. p 3 Use the Player controls to control playback or select other files for playback FA001 R 130311000000 dav ES Full screen Shuffle repeat Select playback time Open files Stop Stop Previous Backone Fast Snapshot recording file frame Play pause Start Slow Forward one Next recording frame file NOTE To view or change where manual recordings or snapshots are saved right click in the video area and select Parameter Setting set File Associated Y MPEG Y Open Option Y use the same player for each media file _ check watermark automatically Save Pic Path C Users lab Documents Pic Sna ps hot folder Record Path C Users ab Documents Record Manual recordin g folder Using the Main Menu AAA ee USING THE MAIN MENU To open the Main Menu e Using the Remote Control Press the Enter button twice e Using the Mouse Right click and click Main Menu NOTE The system password may be required to access the Main Menu By default the User Name is admin and the Password is 000000 MAIN MENU ES SEARCH SETTING E E DEVICE SEARCH ADVANCED BACKUP SHUTDOWN 1 SEARCH Open Search Playback mode For details see Search Playback on page 14 2 INFO View system information Perform firmware upgrades 3 SETTING Configure general system schedule network recording display and motion settings Restore system to factory default
90. r Select the manufacturer of your IP camera e User Enter the camera s user name e Password Enter the cameras password e RTSP Port Enter the camera s RTSP Port e HTTP Port Enter the cameras HTTP Port NOTE See the manufacturer s user manual for your IP camera for the default user name password etc 7 Click OK Click OK again to save changes Manual Add q Manual Add Channel 2 Manufacturer Private IP Address 192 168 0 0 TCP Port 37777 User admin Password CETT Remote Channel 1 Decoder Buffer 280 Auto MER UDP Cancel If the IP address of your IP camera does not appear when you run P search ensure that the camera is connected to the same LAN as Using the Main Menu the NVR or is connected to the PoE Ports You may attempt to manually connect IP cameras using Manual Add To manually add a camera to the NVR 1 Click Manual Add Configure the following e IP Address Enter the public IP address of your P camera e Manufacturer Selectthe manufacturer of your IP camera e User Enter the cameras user name e Password Enter the camera s password e RTSP Port Enter the camera s RTSP Port e HTTP Port Enter the cameras HTTP Port NOTE See the manufacturer s user manual for your IP camera for the default user name password etc 2 Click OK Click OK again to save changes Editing Cameras Ifthe Status indicator on cameras connected to the NVR via PoE o
91. r LAN ts red or if you change the connection details for your IP cameras you will need to update this information To edit cameras 1 Click next to the camera you would like to edit 2 Configure the connection information as needed 3 Click OK Click OK again to save changes Deleting Cameras e Click E next to the camera you would like to delete 31 Using the Main Menu Advanced Configure HDD user accounts and error functions Configure auto restart Save restore system configuration Access Recording Menu HDD Management HDD Management Alarm Set HDD Setting Alarm Release HDD Channel R HDD No Setto Read Write gt Execute Type Status Capacity Record Time HDD Management allows you to format hard drives and manage hard drive settings The top right corner shows hard drive status e 0 Normal hard drive operation e X Hard drive error e Hard drive ts not installed Formatting Hard Drives You must format hard drives before you may use them with the system ATTENTION Formattingthe HDD erases all data on the hard disk This step cannot be undone System settings will not be erased To format a hard drive 1 From Live View right click and select Main Menu gt Advanced gt HDD Management 2 Under HDD No select the hard drive you would like to format Information about the hard drive appears in the lower section of the menu 3 Under Set t
92. r Settings Use the sliders to adjust the brightness contrast saturation and hue for the selected camera Using Search Mode in IE Playback You can access recorded video from your NVR using the Internet Explorer client To access recorded video from your NVR 1 Click Search 2 Configure the following search options e Type Select the type of recording to search for e Begin Time End Time Select the start and end for your search e Channel Select the channel you would like to search or select All e Main Stream Check to search for main stream recordings e Extra Stream Check to search for Extra Stream recordings Extra Stream recordings are lower recording that may be saved on the system to reduce the bandwidth required for remote playback 3 Click Search 4 Under Multiple channel Playback select the channels you would like to playback D9 9 Click a search result and then click Playback to open or Download to save the file to your computer hard drive Type Parameter Operation Peod Paoi Tihe 3 14 2013 9 06 09 AM Playback Configure search Alam EndTime 37157203 v S0603AM rod Type Fie parameters 7 Mation al Channel All Download Local m Picture Open Local Record Main Stream T Extra Stream Multiple channel Playback Select channels H Paraira for playback File SizelK8 m Click a file and then click Playback or Download 817152 93
93. ree A eects eed ceed 106 TFOUDLESNOOUND seconds rc Deemed ena 107 viii GETTING STARTED The system comes with the following components D e POWER ADAPTER X2 NETWORK VIDEO RECORDER 1X FOR POE SWITCH 1X FOR NVR 2 REMOTE CONTROL MOUSE ETHERNET CABLE QUICKSTART GUIDES amp SOFTWARE CD HARD DRIVE SIZE NUMBER OF CHANNELS AND CAMERA CONFIGURATION MAY VARY BY MODEL PLEASE REFER TO YOUR PACKAGE FOR SPECIFIC CONTENT DETAILS CHECK YOUR PACKAGE TO CONFIRM THAT YOU HAVE RECEIVED THE COMPLETE SYSTEM INCLUDING ALL COMPONENTS SHOWN ABOVE BASIC SETUP 7 Connect the Cameras a Connect IP cameras to PoE Power over Ethernet ports OR b Connect IP cameras to the same LAN as the NVR For details on connecting IP cameras over the LAN see Device Search on page 30 2 Connect a Monitor a Connect an HDMI cable not included from the HDMI port on the rear panel to an HDTV or HDMI monitor OR b Connect a VGA cable not included from the VGA port to the VGA port on your monitor 3 Connect the Mouse a Connect the mouse included to one of the USB ports on the front or rear panel 4 Connect the Ethernet Cable a Connect an Ethernet cable not included to the LAN port on the rear panel of system connect the other end of the Ethernet cable to an empty LAN port on your router or switch not included 5 Connect the Power Adapters a Connect the DC 12V power supply to the DC
94. reen l Update 0 cal 3 Check monitors to open them when the CMS software opens or uncheck to disable Screen list Titi Check monitors to have them vii open when the CMS opens Extension screeni Extension screen Screen information 1 L Extension sireeni Update Caneel 4 Click OK to save changes Restart the CMS software to open the new monitor configuration 96 Remote Viewing on Internet Explorer SSS te REMOTE VIEWING ON INTERNET EXPLORER You can also view your system remotely using Internet Explorer version 8 or later required NOTE Remote viewing Is only compatible with Internet Explorer Mozilla Firefox Opera Safari and other browsers are not supported Prerequisites e The HTTP Port default 80 and Client Port default 35000 must be port forwarded to your router e You must create a DDNS account and have the DDNS settings configured in your NVR For details see Appendix D Setting Up DDNS Service on page 97 e The NVR must have Internet access To view your system using Internet Explorer 1 Open Internet Explorer Note that it is recommended to select Run as Administrator when opening Internet Explorer to ensure full functionality 2 Inthe address bar enter your system s IP address or DDNS address followed by the HTTP Port default 80 For example Atto 792 168 7 7 80 or http tomsmith digimerge net 80 NOTE You MUST include http in or
95. s 4 DEVICE SEARCH Connect IP cameras to the NVR 9 ADVANCED Configure HDD user accounts and error functions Configure auto restart Save restore system configuration Access Manual Recording Menu 6 BACKUP Export files to USB device For details see Backup on page 16 7 SHUTDOWN Logout restart or shutdown the system NOTE Checkboxes on the system are filled in white when settings are enabled or empty when disabled 20 Info E The Info menu contains the dl following sub menus showing system information HDD Info HDD INFO Total Space Free Space Status S M A R T 0 00 MB 0 00 MB 14 Page Up Page Down The HDD Info sub menu shows information related to the hard drives installed in the system including capacity status and type Click View recording time to see the start and end times of recordings saved on the hard drives Channel Kb S MB H 0 0 bth lt oO ony om F amp F W NH Nati ee hb be be be be be be be be bel poe ee pe re ote cS fa te le le tS te El dal tes tS eS eS 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 The BPS sub menu shows the bitrates of connected IP cameras Using the Main Menu Type Sian Time 03 07 2013 00 00 OO Log Time Event 2011 Reboot with Flag 0 01 Save METWORK Config iisk totale lt 0 gt Curren working disk lt gt IEFAULT ih nal 03 07 13 13 15 18 ma feb f Disk totals lt 0 gt Current workin
96. s x4 and remove the compartment from the hard drive Door SATA connectors 9 Re insert the hard drive compartment into the unit 6 Push the hard drive door latch in to lock into place 105 Appendix F Hard Drive Installation Formatting the Hard Drive After installing a new hard drive you must format it before the system can recognize it ATTENTION Formatting the HDD erases all data on the hard disk 7h s step cannot be undone System settings will not be erased To format a hard drive 1 From Live View right click and select Main Menu gt Advanced gt HDD Management 2 Under HDD No select the hard drive you would like to format Information about the hard drive appears in the lower section of the menu 3 Under Set to select Format Click Apply Click OK to confirm Wait for the hard drive to format Hard drives become Read Write hard drives by default when formatted HDD Management rw Alarm Set HDD Setting Alarm Release HDD Channel Rh Select HDD SIDA Setto Read Write v Execute Type Select Format Capacity Click Execute tecord lime 106 Troubleshooting _ TROUBLESHOOTING When a malfunction occurs it may not be serious and can be corrected easily The following describes the most common problems and solutions Please refer to the following before calling Digimerge Technical Support e NVR is not receiving power or is not powering up e Ther
97. s for motion detection Configuring Motion Detection Events Motion Detection events allow the system to mark footage that has motion This allows you to quickly locate relevant footage through Search You can also configure system responses to motion detection events such as activating the system buzzer or sending an emall alert To configure Motion Detection events Motion Event Type Motion Detect Channel Enable Period Set Anti dither Alarm Out Latch Show Message Alarm Upload Send Email Record Channel PTZ Activation Select Delay h Tour Snapshot Buzzer Cancel 1 Under Event Type select Motion Detect 2 Under Channel select the channel you would like to configure 3 Check Enable to enable motion detection on the selected channel Under Sensitivity select the motion detection sensitivity between 1 lowest and 6 highest Under Anti dither enter the anti dither time After a motion event occurs and motion stops if motion is detected within the anti dither time the system continues the motion event and includes the new motion within the first event rather than creating a new motion event Under Delay enter the post recording time To configure a schedule when motion detection will be enabled on this channel click Set next to Period Configure times when motion detection will be enabled For example you may want to disable motion detection during business hours and enable it outside
98. sed for backup For details see Configuring eSATA External Hard Drives on page 33 Formatting the USB Device It is recommended to format your USB device before using it with the system To format a USB device A Formatting the USB device will permanently erase all data 1 Insert a USB flash drive not included or USB external hard drive not included into one of the USB ports 2 From live view right click and then select Main Menu Login if prompted 3 Click Backup 4 Check the USB device you would like to format and click Erase Click OK to confirm 1 Name Type LeftSpace TotalSpace Device Status Check the USB device 1 v sda1 USB DISK 7 04 GB 7 50 GB Ready 14 Page Up Page Down Fn Selec Click Erase ____ BES Backing up Video 1 Insert a USB flash drive not included or USB external hard drive not included into one of the USB ports 2 From live view right click and then select Main Menu Login if prompted Click Backup 4 Check the USB device where you would like to save video ad Backup 9 Click Backup BACKUP l 2 Name Type Left Space Total Space Device Status _ Check the USB device y sda1 USB DISK 7 04 GB 7 50 GB Ready 4 Page Up Page Down Select Cancel backup device or file Check the USB device ZAN Erase Stop 6 Configure your search options File Format ASF F ove Add Select search criteria Onekey Backup and then click Add Size KB
99. slow playback 3 Esc In menus press to go back exit menus In playback press to return to live view 4 Directional Keys e Enter Press once to open the System Information screen press twice to open the Main Menu Press to confirm menu selections e Press 4 gt to move the menu cursor e Press 4 w to change menu options 9 Mult Press to switch between full screen and split screen layouts 6 Number Keys e 1 0 In live view press to open channels in full screen e In menus press to input numbers or text input e Shift Press to change input types 7 Add Configure remote control address Rec Press to open manual record menu Fn Press to perform special functions in some menus o p Mouse Control The mouse Is the primary control device for the system To connect a USB mouse e Connect a USB mouse to the USB port on the front or rear panel 1 Left Button e In live view click to open the Navigation Bar e In live view while in a split screen display mode double click an individual channel to view it in full screen Double click again to return to the split screen display mode e While navigating menus click to open a menu option 2 Right Button e During live view right click anywhere on the screen to open the Quick Menu e Within navigating menus right click to exit menus 3 Scroll Wheel Use to change menu options Using the System _ USING THE SYSTEM The default s
100. t 80 DDNS URL Port Number NOTE If you change your HTTP port number port 80 to a different port you must enter your port number after the DDNS address Configuring Email Alerts SMTP Server MailServer Port Anonymous User Name 0 Password Receiver Sender Title ALERT Attachment MM SSL Enable Event Interval 120 HealthEnable Interval 60 Cancel You can configure the system to send out email Using the Main Menu alerts for motion detection or other events NOTE To send out motion detection alerts you must enable the Send Email option for motion detection on each camera For details see Configuring Motion Detection Events on page 28 To configure Email Alerts 1 From live view right click and select Main Menu Log in if prompted 2 Click Setting gt Network 3 Click Network Setting Click Network Setting iP ALTER NTP Check Email and then double click Email 9 Configure the following SMTP Server MailServer Port Anonymous User Name 0 Password Receiver Sender Title ALERT Attachment MM SSL Enable Event Interval 120 HealthEnable Interval 60 Cancel e SMTP Server Enter the SMTP server address 27 Using the Main Menu e Port Enter the port used by the SMTP server e Anonymous Check if your server supports anonymous log ins Otherwise leave this unchecked e User Name Enter the SMTP user name e Password Enter
101. the SMTP password e Receiver Enter the email address that will receive alerts e Sender Enter the sender s email address e Attachment Check to include a jpg image attachment of the camera e Title Enter the subject line for email alerts e Encrypt Type Select SSL or TLS if your server uses encryption Select None if your server does not use encryption e Event Interval Enter the interval between alert emails e Health Enable Check to enable health check emails Health check emails will be sent periodically to ensure that the system is functioning normally e Interval Enter the interval in minutes for health check emails 6 Click Test to send a test email 7 Click OK 8 Click Save to save settings Configuring Switch Settings Switch Settings IP Address IOa Subnet Mask 255 255 Gateway 10 1 Default Cancel You can configure the networking settings for 28 the internal PoE switch NOTE Changing this information from the default values may disrupt the connection to the cameras Make sure your IP cameras are using DHCP or IP addresses that are compatible with your selected settings To configure switch settings 1 Click Network Setting 2 Double click Switch Settings 3 Configure the IP Address Subnet Mask and Gateway for the internal PoE switch 4 Click OK Click Save to save changes The system will restart Motion The Motion sub menu allows you to configure setting
102. the drop down menus to select the channels you would like to playback Click the display options IF Ry to playback multiple channels simultaneously 4 Click inside the video bar to select the playback time The system will begin playing back at the selected time From ReadWrite Hdd RECORD PIC Select the day to playback Su Mo Tu We Th Fr Sa HH 2 3 4 6 7 Y 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 20 Select channels to playback SS y a 00 00 AA AA 0 Synch 3 All Record 4 Normal Alarm Motion Click inside the bar to select a playback time Search Playback Playback Controls From ReadWrite Hdd RECORD PIC Select playback device lt Mar AELE Su Mo Tu We Th Select the day to playback 3 4 10 11 17 18 24 25 31 Select channels to playback Play Play backward Stop Previous Frame Next Frame Slow Speed up Select video clip start end it ji A Y LT lA CARA PUTA CUM NM a o 1 a no 00 00 00 00 00 FER Save selected clip i 24 11 12 1 14 15 1 17 18 20 Stop Synch All Record 4 Normal Y Alarm Motion Select Scope of time bar Show hide recording types Click inside the bar to select a playback time 15 AA BACKUP Backup video files to external USB flash drive not included or self powered USB external hard drive not included NOTE An eSATA external hard drive not included may also be u
103. tion consult your video dealer or local power company For video products intended to operate from battery power or other sources refer to the operating instructions 6 Overloading Do not overload wall outlets of extension cords as this can result in the risk of fire or electric shock Overloaded AC outlets extension cords frayed power cords damaged or cracked wire 12 insulation and broken plugs are dangerous They may result in a shock or fire hazard Periodically examine the cord and if its appearance indicates damage or deteriorated insulation have it replaced by your service technician 7 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the video product Accessories Do not place this Ventilation Slots and openings in the case are provided for ventilation to ensure reliable operation of the video product and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the video equipment on a bed sofa rug or other similar surface This video product should never be placed near or over a radiator or heat register This video product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provide
104. tions provided by the manufacturer e Make sure your cameras are connected to the same LAN as the NVR e Make sure any routers or switches in between the NVR and IP cameras are powered on e Install 2 fresh AAA batteries in the remote control 107 Troubleshooting e Hard drive is not e Hard drive cables are loose or e Remove the housing and check that hard drive detected by the not properly connected cables are firmly connected system e Hard drive has not been e For details see Formatting the Hard Drive on initialized formatted by the page 106 system e There is no hard drive in the e Open the housing and install a 3 5 SATA hard system drive e Hard drive is full e Overwrite is not enabled e From the Main Menu select General Beside HDD and the unit is no Full select Overwrite Click OK to save settings longer recording This enables the system to continuously record by overwriting data once the hard drive is full e Mouse not detected Mouse cable is not firmly e Firmly connect the mouse cable to the system by system connected to the system e Mouse is not connected to the system e System needs to be reset e Re connect the power cord to restart the system e My system does not Recording may be disabled e Right click in live view and click Record Ensure seem to be recording that each channel is set to Schedule or Manual If schedule is selected make sure schedule settings are correct under Setting gt Schedu
105. to determine that the video product is in safe operating condition Wall or Ceiling Mounting The cameras provided with this system should be mounted to a wall or ceiling only as instructed in this guide using the provided mounting brackets Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat Use 19 20 Za 22 Cleaning Unplug the video product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Product and Cart Combination Video and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the video product and car combination to overturn Object and Liquid Entry Never push objects for any kind into this video product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the video product Lightning For added protection for this video product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the video product due to lightning and power line surges General Precautions All warnings and instructions in this manual should be followed
106. trols to control playback Playback Double tap to open in full screen Next frame Play pause Select next video file Select previous video file Enabling Push Notifications Oe Fast Slow You can have the app send push notifications to the notifications area on your device when one of your cameras detects motion Once you have received a push notification you can select it to open 76 Mobile Connectivity live video from the camera that detected motion 9 1 f MON MARCH 25 A 03 25 7 DATAM ae 2013 R 09 17 13 Push notification Miot nye Dele NOTE Appearance of notifications may differ depending on the model of your device NOTE Your cameras must have motion detection activated to receive push notifications For details on enabling motion detection see Motion on page 28 To enable Push Notifications 1 From the Main menu tap Push Config NOTE If Push Config is not shown tap Add check Push Config and then return to the Main Menu 2 Tap the NVR you would like to configure Push Config alg Demo V ay nur v O nvrian B Select the NVR 3 Tap Motion Detect and then check each channel you would like to receive push notifications from nvrian Period 365 days Push type PlayBack o Motion Detect O cam pi ir ds O CAM 2 CAM 3 O CAM 4 77 Mobile Connectivity 4 Tap OK A test notification will be sent to your d
107. ual recording options See Recording on page 24 e Device Search Open the Device Search menu to manage IP cameras e Alarm Output Open the Alarm Output menu e Main Menu Open the Main Menu See Using the Main Menu on page 20 Adjusting Color Settings Use the Color Settings menu to adjust color settings for your IP cameras To adjust color settings 1 Right click on the channel you would like to configure and select Color Setting Enter the system password if prompted 2 Adjust the Hue Brightness Contrast and Saturation settings that the camera will use To enable custom Gain controls check Gain and use the slider to configure the gain level Using the System OR Use Color mode to select a preset color profile Yo COLOR Sl TING Period Y 00 00 00 00 Hue 50 Brightness 50 Configure color Contrast 50 settings for the Saturation 50 first time period Gain 50 Color mode Customized1 7 Customized Default Cancel NOTE Color settings will update once you save changes NOTE To configure the Customized1 4 profiles click Customized 3 Click OK to save changes Using the Navigation Bar The Navigation Bar gives quick access to certain functions and menus To open the Navigation bar e Left click on the screen to open the Navigation Bar The Navigation Bar has the following options Main Menu Selectdisplay Search Network Viewsystem layout info Collapse PTZ Alarm HDD Status Manage
108. ucts are subject to continuous improvement Digimerge Technologies Inc a FLIR company and its subsidiaries reserve the right to modify product design specifications and prices without notice and without incurring any obligation E amp OE 86 Appendix B Setting up Remote Viewing An APPENDIX B SETTING UP REMOTE VIEWING Setting up the Remote Viewing Feature requires several steps Networking skills are required to correctly configure the remote viewing functions What Do Need e NVR System e APC with the installed CMS software NOTE For Mac users please visit www digimerge com for instructions e Arouter not provided with the system and High Speed Cable or DSL Internet Connectivity for remote viewing outside your network Network Setup Remote Access Overview To setup remote viewing 1 With the system powered off connect the system to the router using an Ethernet cable ROUTER Not Included Not Included 2 Power the system on 3 Press the Enter button on the remote control to find your system s IP address 4 Enable Port Forwarding on your router for the Client default 35000 and HTTP Ports default 80 To set up port forwarding use the included Auto Port Forwarding Wizard software see Appendix C Auto Port Forwarding Wizard on page 90 or refer to your router manufacturer s instructions 5 Setup an account at http ddns digimerge net For details see Appendix D Setting Up DD
109. umber and Version 0 00 cece cee eee eens 91 A A E EE EESE E A E a 91 CONTIQUEAUON sa dat es ARS ide ee eee 91 Intalstartups Select language i i428 tal aed ts a A aid 92 Step 1 Populate the Router Database ist A di ai 92 Step 2 Enter your Router Settings cid god he eee ras A a a aa paa 92 Stepo Update the ROULEr SeNnNgS taa a cas 94 Step 4s Test VOUT COMME CUCM ir Riga da be hare ee Mee ie 94 Contiguring Multiple ROUters sinus oo eames BAe oka is ae tae ences Sea iaa gaa eS 94 Scenario A Router Modem Combination Router 0 ccc ee ene nen eens 95 Scenario B Multiple Routers stud rd ide 99 TIO es ay renter eel ok Sow ress i apts ates cas Sree Nae a eet An le Ge aparece rad E A dl ola 96 Appendix D Setting Up DDNS Service 0c c cee eee ee 97 How Do Enable DDNS On My System 0 0c ccc ees 98 Connecting to your system using DDNS ee es 99 EMSSORNWaFo OF MOBILE ADOS a Ia ooo 99 Merne t ED ON OP AAA a AA a A A Seah id 99 Appendix E Remote Firmware Upgrade 0 0 ooooooooooo mo 100 Installing a Firmware Upgrade Over the LAN 0 000 cece ee eee eee 100 Installing a Firmware Upgrade Over the Internet 00 cee eee aee 101 Appendix F Hard Drive Installation 0000 e eee eee eee 103 Installing a Hard DIV cosoriin cot eee Oaeade Miedo oor ooo aes 103 Removing the Hard Drive s 022tene dira Aaa wk a a a 104 Formatting the Mara DEIVO scucss coast de agede S
110. use Property MouseSet Startup Wizard Auto Logout 5 Navigation Default Cancel 4 Click Save NOTE To configure Daylight Savings Time see General on page 23 To configure NTP see Configuring NTP on page 26 RECORDING By default the system Is set to immediately record at startup from connected cameras This Is called Continuous Recording It is highly recommended to keep Continuous Recording on at all times The system supports the following recording types e Continuous Recording By default all camera channels are enabled with Continuous Recording During Continuous Recording the Record icon 55 appears in the channel e Motion Recording Cameras can be configured to record and mark events when motion Is detected When motion is detected the Motion icon appears in the channel NOTE You must enable motion recording in the Schedule before the system will record motion events For details see Schedule on page 24 e Alarm Recording Cameras can be configured to record when external alarm devices are triggered Search Playback SEARCH PLAYBACK Search mode Is used to navigate and playback recorded video files on the NVR Playing Back Video from the Hard Drive 1 From live view right click and then click Search If needed log in using the admin account default User Name is admin and default Password is 000000 2 Use the calendar on the right to select the day to playback 3 Use
111. ystem Configuring Multiple Routers Your network may have two or more connected routers During the initial launch of the auto port forwarding wizard the program scans the network to detect the number of connected routers To check for multiple routers 1 Click the Detect Multiple Routers button fe e A list of connected routers populates in the window DIG MERGE Rizh tor Rrsiness san nan aras e The Possible 1st Router refers to the router directly connected to your system This Is the router that requires the port forward information 94 Appendix C Auto Port Forwarding Wizard e The Possible 2nd Router refers to the router immediate to the internet connection This is the router that requires you to configure a DMZ host connection Scenario A Router Modem Combination Router e You may have a router modem combination with a second router in your network Scenario B Multiple Routers e You may have two routers in your network Internet Port Forward port 80 amp DMZ IP 994 to Router 1 Computer e Aa E A oe 00000 2999 NVR System EXAMPLE LINKSYS by Cisco Applications 4 Gaming All of your Internet and network connection details are displayed on this page The firmware version is also displayed here Network Status Established Connection Up Time 0 Days 0 48 36 MAC Address 00 1E 58 2E 43 A A ub Default Gateway 192 168 1 1 Primary DNS Server 20
112. ystem password ts 000000 Password By default the login password Is enabled The default system password is 000000 On Screen Display The system shows the following for all display views CAM 3 E e Double click on a channel to view in full screen double click again to return to split screen 1 Display Area e Right click to open the Quick Menu See Using the Quick Menu on page 8 e Left click to open the Navigation bar e Move the mouse to the top of a channel to view the Camera Toolbar e Click and drag cameras to rearrange the channel display This does not affect the channels each camera is connected or recording to 2 Channel Name 3 Channel Status Icons fers Channel is recording gt Motion has been detected a Camera is locked covert mode is activated Using the System Using the Quick Menu The Quick menu gives you access to the system s key functions To access the Quick Menu right click the screen during live view View 1 View 4 Pan Tilt Zoom Color Setting search Record Device Search Alarm Output Main Menu The Quick Menu has the following options e View Select a camera in full screen or select a multi channel display e Pan Tilt Zoom Access controls for PTZ cameras not included e Color Setting Configure color settings for IP cameras e Search Search playback recorded video See Search Playback on page 14 e Record Open the Record menu to select man
113. zard 1 Download the Auto Port Forwarding Wizard from www digimerge com and run the installer file e The installation window opens 2 Click Next to continue ES Digimerge Auto Port Forwarding Setup Welcome Welcome to the installer for Digimerge Auto Port Forwarding 1 0 0 lt is strongly recommended that you exit all Windows programs before continuing with this installation Tira collara vel bs labs in Le lokia bed belen To seed a dilareni bealion ethe pe ma new path or cick Charge do benage dor am mentir folder ff you have any other programs running please click Cancel pp pina andina this gey instal Diimerae ea Pon Ending tn Otherwise click Next to continue CAProgram Fiber Digrmrerge Ato Port Pomada Select Space required 5 23 ME installation Space avolable on selected diva 276268 directory optional Click Next 3 Click the Change button to change the default installation directory optional Click the Next button to continue 4 Select the users who can see the Auto Port Forwarding shortcut Optional Click the Next button to continue Dagimenge Auto Port Forwarding Set j e Wilber uba you lite the horita to be relaed Y Tre eee oana ll ba cremate m ha folder nte emo F you dor wani 16 mes Chem ee loide pay can ciber hae a res Fases of seed an cli folder tron he ll Sorte Folder Lipa Ao Peet Farding 6 naa hates hor cur aber ony Make aboecuts avaleble to al use Select the users who

Download Pdf Manuals

Related Search

DNR200V_SERIES_MANUAL_EN_R1_web

Related Contents

  INSTALLATION & OPERATING INSTRUCTIONS  Bloc d`alimentation stabilisée DC haute précision à quadruple sortie  2009年3月期 業績見通し  D112 / D114  MINUTES OF THE PRE-BID MEETING OF “DIGITIZATION OF  

Copyright © All rights reserved. Failed to retrieve file