DLK642 Lite
Contents
1. Premisses A amp B 4 for access A green LED2 access rights 6 for access B green LED3 1 relay 1 green LED2 eee 2 relay2 red LED2 yelow PED 2 9 3 transistor output green LED3 3 Not used 4 Day night switch right 1 green LED 2 1 1 category 2 2 category green LED 3 gt Code category 3 3 category green LED 2 4 4 category green LEDs 243 Code parametres editing finish press twice 4 button to move to higher menu level Next button pressing switches control panel to the main mode 40 seconds pause between digits entry causes panel switching to main mode category status change permission access mode 1 not active prohibited 2 active permitted twenty four hour 3 active prohibited day 4 active permitted day Previewing and modifying users codes settings Press 2 7 and then enter code number or code in programming mode Now you can edit current code parameters Access through access points settings Press 1 being in code parameters programming mode Green LEDs will reflect current parameters settings If LED2 is on door A access is permitted if LED3 is on access is granted through point B You can change settings by pressing of 4 button access point A switch on off or 6 button access point B button pressing returns panel to current code parameters editing Press to move to the highest menu level The2. www itvsystems com ua Integrated Technical Vision Ltd 27 Programming the panel in stand alone use Changing Code Each user of 2 and 4 code category can change a code using button command To change a code press buzzer utters three sound signals accompanied by LEDs flashes Now introduce actual user code then new user code and twice New user code will be accepted if the present code type has permission for code change if actual code is correctly introduced and if new code does not coincide with already existing codes or duress codes To exit code change programming mode press button You cannot change engineer or master code with the method described above For example 1 2 3 4 5 6 code user wants to change the code for 6 5 4 3 2 1 User should necessarily have code category 2 or 4 Press button you will hear three long sound signals LED2 starts to blink red Enter user old code 1 2 3 4 5 6 long signal will be heard In case of false code entry or code category 1 or 3 an error signal will be heard Enter new code 6 5 4 3 2 1 long signal confirms correct code entry Enter new code 6 5 4 3 2 1 7 repeatedly long confirmatory signal will sound Press long confirmatory sound and the panel switches to the main mode Switching Day Night Modes 28 To switch day night mode press 1 4 LED 2 blinks yellow then enter user co
3. 40 seconds pause between digits entry or cards passing causes panel switching to main mode Door B time Press 1 4 in code parameters programming mode the panel reflects current parameters settings by means of buzzer and LEDs button pressing switches the panel to upper menu level To set new parameters press button and then enter time in seconds from 0 to 255 and press Factory default is 20 The door will be open for unlimited time if you set time to 0 or 255 sec For example Door B time setting is similar to door A time setting succession Programming Inputs Press 1 8 in programming mode and introduce input number Then you can proceed with inputs type 1 or attribute 2 programming Inputs type Press 1 after you have chosen the number of input the panel reflects current input type by means of buzzer and LED 3 The panel switches to input programming mode after button pushing To introduce new settings press then enter type number 0 or from 18 to 29 and press Inputs types 0 input is not used 18 door sensor 19 RTE button 20 both doors free pass access 21 both doors blocking 22 served by external program 23 accumulator status 24 220V status 25 door A free pass access 26 door B free pass access 27 door A blocking 28 door B blocking 29 door sensor and RTE button Q If input t
4. 7 code is deleted and panel moves to upper menu level red LEDs 1 and 2 blink and LED3 is off Next button pressing leads to exiting the programming mode LED2 blinks red Resetting to factory defaults Press 5 4 being in code parameters programming mode then enter engineer code All settings are reset to factory defaults and the panel turns to the main mode All previously programmed codes cards engineer and chief codes are programmed according to factory settings by reset to factory defaults operation In case of engineer code loss turn to hardware reset to factory defaults section For example It is necessary to carry out reset to factory defaults of the panel Press 5 in engineer code programming mode red LEDs 1 and 2 blink synchro nously enter engineer code reset is executed panel is in main mode red LED2 blinking Group card registration Press 10 in code parameters programming mode then pass all cards in turn for registration To exit group card registration mode and move to upper menu level press button After next button pressing panel switches to the main mode The following parameters are set to all cards registered in this mode point B access permission outputs management prohibition 22 Integrated Technical Vision Ltd http www itvsystems com ua Programming the panel in stand alone use no day night switch permission code category 3 The panel will i
5. press red LEDs 1 and 2 blink alternately to move to upper menu level press red LEDs 1 and 2 blink alternately LED3 is off To exit programming mode and switch the panel to programming mode press LED2 blinks red 40 seconds pause between digits entry causes panel switching to main mode Programming Outputs Press 1 9 4 in programming mode and enter output number 4 Then you can proceed with outputs type 1 attribute 2 time 3 4 or mode 4 7 programming Output type Press 1 after you have chosen number of the output the panel reflects current output type by means of buzzer and LED 3 The panel switches to output programming mode after button pushing To introduce new settings press then enter type number from 0 to 3 2 Outputs types 0 output is not used 1 lock output is activated at valid code entering or valid card passing 2 bell output is activated when access point switches to blocked mode 3 alarm output is activated when access point switches to blocked mode If you set the same type for two outputs e g two bell outputs then only the output with the minor number will be assigned the set type Output attribute Press 2 after you have chosen number of the output the panel reflects current output attribute by means of buzzer and LED 3 The panel switches to output programming mode after button pushing To introduce new se
6. signals and see all LEDs blink then LEDs 1 and 2 blink alternately and LED 3 is off Factory defaults are engineer code 1234 and master code 5678 Engineer and master code should be changed during programming Code length should not be less than four digits Invalid code or false command entry are indicated by long sound signal of the buzzer and LED 1 red and LED 3 green flashing The panel ignores RTE button contact break shortage in any programming mode Control panel programming diagram is enclosed in Appendix section Factory defaults The panel switches to main day mode when first engaging or resetting to factory defaults with the following settings Keyboard blocking time 40sec Engineer code 1 2 3 4 Master code 5 6 7 8 Internal reader works only Relay 1 runs door B locking device works in impulse mode locking device time is 1sec Relay 2 runs bell works in the impulse mode time is 5 sec First transistor output SA contact is programmed for alarm Second transistor output BEL contact is not used Single one sided door B is used only Cord 1 is used as door B contact sensor Cord 2 is used as door B RTE button Cord 3 is used as door B fire alarm input free pass Cord 4 is used as door B blocking input Cords 5 8 are not used 18 Integrated Technical Vision Ltd http www itvsystems com ua Programming the panel in stand alone use Access time is
7. to add the resistive load Take care of proper grounding of all panels in the network Setting control panel address Panel address is set during programming See Control panel address programming section Outputs types and attributes You can set definite function attribute time and one of four operating conditions for every output that is to fix their type during programming See Controller program ming PIN entry card passing PIN entry is carried out by consecutive keyboard buttons pushing It should be from four to ten figures length and is complete after button pushing Every button pushing is accompanied by short built in buzzer sound If the entered PIN is invalid one long sound will be heard If invalid not registered PIN or ID card is entered more than three times this value can be programmed the keyboard will be blocked for time set in engineer code programming mode Keyboard blocking is signalled by red LED light Number of PIN matching attempts from 0 to 255 is programmed using engineer code Number of attempts is not counted see Matching attempts number section Door blocking time from 0 to 255 is programmed using engineer code see Door blocking time part You can cancel mistaken code entering my means of button During PIN entry 40 seconds interval cancels previous figures entering Proximity card ID card passing is equal to PIN entry Controllers work with ASK and FSK modulatio
8. warranties whether expressed or implied and of all other obligations or liabilities on the part of ITV Ltd This warranty contains the entire warranty ITV Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any warranty or liability concerning this product In no event shall ITV Ltd be liable for any direct indirect or consequential damages Loss of anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product Integrated Technical Vision Ltd http www itvsystems com ua http www itvsystems com ua Integrated Technical Vision Ltd 31 C Codes Adding user code 19 cardholders codes 15 cards registeration 23 changing codes 28 engineer code 19 master code 19 users codes 21 Control panel address 15 28 Duress code 16 D Defaults factory defaults 18 23 29 Door sensor 13 Door sensor and RTE button connection 13 Door time 17 Duress code 16 Identificators 27 Inputs 7 10 programming inputs 25 LEDs 16 Locking devices 13 32 Integrated Technical Vision Ltd Index M O P R Modes autonomous 17 day night modes 29 Outputs 10 alarm output 16 programming outputs 26 relays 7 transistor 7 14 PIN 15 Power consumption 7 supply wiring 14 Programming 18 Reader connection 12 operation 28 RTE button connect
9. 0 3A For connection of executional BEL Transistor output open devices drain 0 3A Z6 Zone 6 GND GND Z5 Zone 5 ZA Zone 4 GND GND 1 6 EOL inputs connection Z3 Zone 3 Z2 Zone 2 x2 GND Common Z1 Zone 1 GND 12V EB 12V BZ Buzzer control DI DATA 1 Reader connection terminals DO DATAO GN Green LED control RD Red LED control RST resetjumper S3 S4 S6 jumpers for RS485 load selection S8 S9 readermode setting jumpers 10 Integrated Technical Vision Ltd http www itvsystems com ua Mounting Mounting The controller is intended for inside mounting at 80 relative humidity When the panel is mounted on metal surface its reading distance decreases Do not mount the panel or lay wires closely to the main power wiring and other sources of electromagnetic interference To mount the panel on the wall proceed as follows Release the screw in the lower part of the cover Figure 3a Lift front cover slightly in the bottom part and pull it downwards Figure 3b Sa Sy U w Fixing tabs a b c d Figure 3 DLK642Lite mounting specifications Disconnect X3 connector of built in reader from panel PCB Carefully release fixing tabs Figure 3 c then dismount PCB from panel base Mark places for fixing holes using back plate as a template Figure 3 d then drill with the 6 mm auger openings to depth of th
10. 20sec Proximity cards types are ASK and FSK Changing engineer and master codes Engineer code may be changed only in engineer code programming mode To change master code proceeds as follows In engineer or master code programming mode push 0 then introduce new master code twice The panel will turn to the highest menu layer To go out of programming mode press button New code will be admitted if it does not coincide with already existing users codes For example To change master code 7 7 7 7 in engineer programming mode press 0 LEDs 1 and 2 blink red and LED3 blinks green synchronously then twice enter master code 7 7 7 7 followed by button pressing LEDs 1 and 2 blink red alternately and LED 3 is off Next button pressing switches panel to main mode LED 2 blinks red Adding user code To add user code do the following In programming mode push 1 panel indicates first free access code number with the help of buzzer and LED 3 Introduce user code then you can change code parameters or move to the highest menu level button New code will be admitted if it does not coincide with already existing users codes or duress codes The following parameters are set for new code door B access permission has no outputs management permission cannot switch day night modes 3 third code category Code parameters change is shown in the table Codes c
11. Standalone Networked Access Control Panel DLK642Lite DLK642 Lite ACCESS C ONTROL P ANEL Integrated Technical Vision Ltd http www itvsystems com ua This manual covers installation programming and utilization of the DLK642Lite access control panel Read this manual carefully prior to installing and program ming the unit Design Change Disclaimer Information due to design changes and product improvements in this manual is the subject to change without notice ITV Systems reserves the right to change the product design any time that will subsequently affect the contents of this manual ITV Systems assumes no responsibility for any mistakes that can appear in the manual The company guarantees that this Installation Manual is up to date and corresponds with the unit you purchase Reproduction Disclaimer All rights to this document are preserved by ITV Ltd Copying printing and any other kind of unauthorised reproduction of this document or a part of it is prohibited Trademarks ITV is a registed trademark of ITV Ltd Training and technical support ITV Ltd performs training on the installation programming and utilisation of the DLK642Lite access control panel For detailed information about the training and discussing of our particular requirements to the unit please contact our personnel by the phone numbers below It is recommended for the staff intended for sales and installation of the DLK642Lite access con
12. additional programmable transistor outputs for siren bell or other agents control Bell and SA outputs are rated at 500 mA 24V and sink to the These outputs are electronically 11 GND 78 PWR TM NCl Cl NO1 NC2 C2 NO2 protected against overload In case of overload the correspond ing event is generated 12 V Power supply wiring l R R 3v It is recommended to use PSU 1 5 GND power supply with battery backup 2 KOM 2 KOM manufactured by ITV Ltd This power supply provides 12V power rated at 1 5 A 4AH or 7AH battery may be used in it PSU 1 5 Power power supply has supply outputs for block signaling of mains power state and battery state Wiring with mains power and battery state by Z7 and Z8 terminals is shown on a picture l RS 485 Interface RS 485 Interface is used for networking of system components PC and panels Length of RS 485 bus is up to 1200 meters Number of panels is up to 32 pal N lt 2 F4 e vu 2 power good battery good SOV RS 485 port is protected against over voltage 60V and cross polarity The unshielded four wire cable may be used for RS 485 wiring For maximal 1200 meters distance please use 0 4 mm cross section wire 0 2 mm cross section wire will provide the distance of 500 meters 14 Integrated Technical Vision Ltd http www itvsystems com ua Wiring On the first and last panel in the drop line short S3 S4 S6 jumpers
13. ategories explanation To go out of programming mode push button Code categories explanations are in table below Next button pressing switches the panel to main mode For example In is necessary to add 231964 code and set point A access for it and and proximity card for accees through points A and B Using engineer code programming mode press 1 LED 1 blinks red and buzzer and green LED 3 indicate vacant code number then LED 1 and 2 blink red and LED 3 blinks green Enter 2 3 1 9 6 4 4 code panel proceeds with code settings editing LED 1 blink red and LED 2 blinks yellow alternately Press 1 buttons LED 1 blinks red and LED 3 blinks green switch on green LED2 and Switch off LED3 by 4 and 6 buttons pressing then press LED 1 blinks red LED2 blinks yellow Press panel turns to upper menu level LEDs 1and 2 blink red alternately LED 3 is switched off http www itvsystems com ua Integrated Technical Vision Ltd 19 Programming the panel in stand alone use Press 1 LED1 blinks red buzzer and LED3 indicate vacant code number then LEDs blink synchronously Pass a card to reader after card code read panel proceeds with card settings editing LED1 blinks red LED2 blinks yellow alternately Press 1 LED1 blinks red LED3 blinks green Switch on green LEDs 2 and 3 with buttons pressing Then section action indication 1
14. blinks red buzzer and LED3 reflect current keyboard lockout time then red LED1 blinks If current setting differs from 10 press red LED1 and green LED2 blink synchro nously Press 1 0 7 the panel switches to upper menu level LEDs 1 and 2 blink red alternately Next pressing of button switches the panel to main mode LED2 blinks red 40 seconds pause between digits entry or cards passing causes panel switching to main mode Door A time Press 1 3 in code parameters programming mode the panel reflects current settings by means of buzzer and LEDs button pressing switches the panel to upper menu level To set new parameters press button and enter time from 0 sec to 255 sec and press Factory default is 20 The door will be open for unlimited time if you set time to 0 or 255 sec For example It is necessary to set door A time to 30 seconds In engineer code programming mode LEDs 1 and 2 blink red LED3 is off press 1 3 LED1 blinks red buzzer and LED3 reflect current door A time then LED1 blinks If current setting differs from 30 press red LED1 and green LED2 blink synchronously Press 3 0 4 the panel switches to upper menu level LEDs 1 and 2 blink red alternately LED3 is off Next pressing of button switches the panel to main mode LED2 blinks red http www itvsystems com ua Integrated Technical Vision Ltd 23 Programming the panel in stand alone use
15. de and press f Red LED 1 is switched on in night mode and switched off in day mode Integrated Technical Vision Ltd http www itvsystems com ua Programming the panel in stand alone use Resetting hardware to factory defaults 1 Close TM and BEL terminals with the bridge when power is off 2 Switch on the power buzzer utters several short sound signals LEDs blink synchronously after short pause 3 Switch off panel s power 4 Take off TM and BEL terminals bridge The panel is ready for the operation 099999929990 NC1 Cl NO NO2 SA BEL PW R _ TM 0 http www itvsystems com ua Integrated Technical Vision Ltd 29 Limited Warranty Limited Warranty 30 ITV Ltd warrants that for a period of eighteen months from the date of purchase the product shall be free of defect in materials and workmanship under normal use and that in fulfillment of any breach of such warranty ITV Ltd shall at its option repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in parts and workmanship and not damaged incurred in shipping or handing or damaged due to causes beyond the control of ITV Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be lieu of any and all other
16. door opened or at finishing of door time interval Bell or alarm output is switched off at ending of door blocking time interval Q or at breaking and shorting of Blocking or Free pass input For example It is necessary to set the following parameters for output 1 door A lock operating time 3 seconds impulse operating mode In engineer code programming mode press 1 9 red LEDs 1 and 2 blink synchronously Press 1 red LED1 and yellow LED2 blink alternately Press 1 again red LED1 blinks buzzer and green LED3 reflect output 1 current type setting Press to proceed with output attribute setting red LED1 and green LED2 blink synchronously Press 1 new value is accepted red LED 2 and yellow LED2 blink alternately Press 2 red LED1 blinks buzzer and green LED3 reflect current output attribute setting Press to proceed with output attribute setting red LED1 and green LED2 blink synchronously Press 0 new value is accepted red LED1 and yellow LED2 blink alter nately Press 3 red LED1 blinks buzzer and green LED3 reflect current time of output 1 engaging Press to proceed with output time setting red LED1 and yellow LED2 blink synchronously Press 3 new value is accepted red LED1 and yellow LED2 blink alternately Press to proceed with output operating mode setting red LED1 and green LED2 blink synchronously Press 2 new value is accepted red LED1 and yell
17. dware to factory defaUltS iu kek 29 Limited Warranty 3c sul e ee ie t ete ee eau ena Wak r nau qu 30 io r eee inet DD tena E 32 http www itvsystems com ua Integrated Technical Vision Ltd 5 Preface Preface DLK642Lite stand alone networked access control panel is an advanced version of DLK641Plus stand alone access control unit designed for use in multi door system It has external specialized reader and can control two doors In addition to DLK641Plus functions DLK642Lite can be networked into the sophisticated access control system using NDC BO52 access control panel as the master controller It allows you expanding of simple access control system to high end access and security system DLK642Lite can be downloaded either from built in keyboard or from PC All valid card numbers time zones and relay pulse times are loaded to controller memory The panel can control access into two doors with no dependency on a central computer system Primary goals of Access Control System are identification of a person confirmation or not confirmation of access control of movements in a necessary zone It can provide time and attendance logging in addition to the usual task of restricting individuals access to certain areas All users access information is gathered by a server where administrators can retrieve and analyze the information This data provides recording of staff movement within an organization whether it i
18. e concrete insert Pull the wires Secure back plate with the screws Fix PCB on the back plate Connect the wires Connect PCB of the built in reader to panel PCB Fasten front cover Figure3a http www itvsystems com ua Integrated Technical Vision Ltd 11 Wiring Wiring Connecting readers DLK642Lite can control two access points using two readers They can be readers produced by ITV Ltd or other readers with Wiegand interface X2 terminal block is intended for access point A entrance in case of double sided door reader connection It can be iPN series reader or another one with Wiegand interface X3 terminal is intended for access point B exit in case of double sided door reader connection Reader and controller are to be mounted on wall directly at a door at convenient height The wiring is shown on Diagram below Built in reader Wiegand Built in reader iPN series connection reader connection reader cord cord D1 DO CN RD D1 DO GN RD eee Wires colors can differ in readers of other vendors Please refer to your reader installa tion manual External reader connecting cable length can be increased up to 50 meters by AWG 8x0 22 cable During increasing of cable length mind the conductors Do not mount the reader on metal surface It decreases reading distance Reader is to be mounted at sm minimum distance from controller Otherwise reading distance wil
19. ill be engaged at every door sensor violation except for door time interval on conditions that door sensor is connected to the output Alarm output engages on programmed time up to 255 seconds Alarm output does not switch on at 0 seconds value Alarm output time is programmed with engineer code There are three LEDs on front plate of the controller See figure 1 LEDs meanings in main mode are described below 1 LED1 red indicates controller operating mode day night 2 LED2 red green indicates controller state norm red LED blinks free access green and yellow LEDs blink in turn keyboard lockout red LED lights continuously Green LED lights continuously LEDs programming mode meanings 1 LED1 red blinks the whole programming period 2 LED2 red green indicates users codes categories and parameters 3 LED3 green indicates users codes categories and parameters and figurative volumes of controller programming settings Door time If door sensor is open the corresponding access point goes into alarm Alarm is not invoked if the contact is opened during Door Time interval This interval starts when access is granted and lasts for programmed time or terminates on opening and subsequent closing of door sensor Door time is programmed using engineer code it can be from 0 to 255 seconds Integrated Technical Vision Ltd http www itvsystems com ua Control Panel Operation Open door Door can be open for unlimi
20. ion 13 Door sensor and RTE button 13 http www itvsystems com ua 060504
21. l be decreased 12 Integrated Technical Vision Ltd http www itvsystems com ua RTE button R yarpyakn R weyan Request To Exit RTE button is used in case Access Access of one sided door Door opens on RTE point B point A button pressing for going out RTE RTE RTE button may be used for remote door button opening secretary or guard opens the door for instance Wiring of the normally opened RTE button is shown on diagram RTE is wired to Z5 and Z6 terminals Itis not recommended to use Z7 and Z8 termi nals for RTE button connection Usage of unblocking button on electric lock instead of RTE will cause Door Forced event Rapea Ranya r n Access Access point A point B J Door Door contact contact Door sensor Door state opened or closed is determined by door sensor If door sensor is not connected the panel is not able to determine events of door force or unclosed door Wiring of normally closed door sensors to Z3 and Z4 terminals is shown on wiring diagram Q Itis not recommended to use Z7 and Z8 terminals for door sensor connection Door sensor and RTE button connection Controller inputs can be programmed for simultaneous use of Door sensor and RTE button R aryan Riaya In this case cord break means Door sensor eae Access break and cord shortage RTE button E point A pressing contact Door Any of eight cords can be used as a and RTE j contact c
22. m composition The panel has slave function in access control system All parameters and settings of access points and codes cards are determined by system possibilities Only panel s address is uploaded from controller Programming the panelin stand alone use Programmed information representation Numerical parameters downloaded to the panel are reflected by means of built in buzzer and LED 2 A figure corresponds to the number of sound signals and LED 2 blinks Figures are separated by pauses http www itvsystems com ua Integrated Technical Vision Ltd 17 Programming the panel in stand alone use For example number 235 is displayed as follows 2 blinks pause 3 blinks pause 5 blinks Zero is signalled by one long Buzzer sound and LED2 flashing For example 040 will be reflected by 1 long flashing pause 4 blinks pause 1 long flashing Code settings are reflected by LEDs 2 and 3 blinks Programming via PC DLK642 Lite panel can be connected to PC using interface converter NTC LNET or NTC LNET Lite that allows easy autonomous mode programming For the detailed information turn to software user manual Programming via built in keyboard The panel cannot switch to programming mode if it is in main mode resistor load should be connected to all used outputs In order to turn the panel to the programming mode enter engineer or master code on keyboard engineer code OR master code You will hear several short sound
23. n cards Cardholders codes There are several proximity card types used for controller management in autonomous mode 00 card number is engineer code All parameters are set using engineer code 01 card number is chief code It allows 0 4 and 10 programming section entering 02 999 code numbers are cardholders codes By means of access codes proximity cards people can receive access grant operate relay change day and night modes Some information is programmed for every user individually That is access to each door grant prohibition programmed outputs operation code category 1 4 day night modes change permission http www itvsystems com ua Integrated Technical Vision Ltd 15 Wiring Code category access schedule prohibited eel permitted twenty four hour prohibited day permitted day Duress code Every PIN user has additional duress code Such code introduction leads to alarm output engaging When this code is entered control panel grants access accord ingly to user code access level and options and moreover alarm output switches on Cardholders using proximity cards do not have duress codes Q Duress code differs from PIN code to one in the last figure e g If PIN code is 123456 then duress code will be 123457 If PIN code is 203409 then duress code will be 203400 Alarm output switches off after actual code entry Alarm output LEDs Alarm output w
24. n on Diagram 1 below 1 2 3 1 3 LEDs 4 built in keyboard 5 back plate 6 panel PCB 7 PCB of the ID reader 8 front cover Figure 1 8 General view of DLK642Lite b DLK642Lite with front cover off 8 Integrated Technical Vision Ltd http www itvsystems com ua What s inside Wiring Configurations External reader Built in reader PCB gt Panel PCB i O Alarm output IN Door contact Nn RTE button contact EN Power supply 12V Figure 2 Terminals layout http www itvsystems com ua Integrated Technical Vision Ltd 9 What s inside Terminals Assignment Termi nal Terminal Function Description block A RS485 A B RS485 B GND RS 485 Common BSB dropimg EB 12 RS485 ZI Zone7 GND Common EOL supervised programmable Z8 Zone8 inputs 7 8 connection PWR Power Terminals for connecting power supply TM Tamper Contact Tamper contact output Normally closed XI NCI Normally closed Cl Common Relay 1 contacts NOI Normally open NC2 Normally closed C2 Common Relay 2 contacts NO2 Normally open SA Transistor output 12 V
25. n panel turns to code parameters programming button pushing returns the panel to the highest menu level http www itvsystems com ua Integrated Technical Vision Ltd 21 Programming the panel in stand alone use Next button pressing leads to going out of the programming mode For example It is necessary to replace lost card code number 12 by code 232002 with code settings reservation Press 3 in engineer programming mode red LEDs 1 and 2 blink synchro nously Press 1 2 panel indicates card code with buzzer and LED3 signals Press red LEDs 1 2 and green LED3 blink synchronously Enter panel proceeds with current code settings editing red LED1 and yellow LED2 blink alternately Press to move to upper menu level Next button pressing switches the panel to main mode 40 seconds pause between digits entry or cards passing causes panel switching to main mode Code card deletion Press 4 4 being in code parameters programming mode then enter code number or code Code card is deleted and the panel moves to upper menu level Next button pressing leads to exiting the programming mode After code card deletion code number becomes vacant When new code card is registered the smallest vacant number is chosen For example It is necessary to delete code with 34 number Press 4 in engineer code programming mode red LEDs 1 and 2 blink synchro nously Press 3 4
26. n press 4 again in order to exit programming mode Direct outputs management Press 1 being in code parameters programming mode LED 2 and 3 reflect current parameters settings green LED 2 relay 1 management red LED 2 relay 2 yellow LED 2 relays 1 and 2 green LED 3 transistor outputs management 20 Integrated Technical Vision Ltd http www itvsystems com ua Programming the panel in stand alone use You can change settings by pressing 1 button relay 1 management switch on off 2 relay 2 management switch on off and 3 transistor outputs switch on off button pressing returns the panel to current code editing Then press to move to the highest menu level To exit programming mode press button Day night mode switch Press 4 in code parameters programming mode LED 2 reflects current parameters settings Code card can switch day night mode if green LED 2 is on You can change settings by pressing 1 button button pushing returns the panel to current code card parameters editing Press to move to the highest menu level Next pressing leads exiting programming mode Code category Press 5 being in code parameters programming mode Green LEDs 2 and 3 reflect current code parameters settings in double code see Table 1 You can change settings by pressing 1 button for category 1 2 for category 2 3 for category 3 4 for category 4 button pressing retu
27. ndicate mistake at already existing card registration attempt Code matching attempts Press 1 1 when been in code parameters programming mode the panel reflects current parameters settings by means of buzzer and LEDs button pressing moves the panel to upper menu level To set new parameters press button and introduce number of attempts from 0 to 10 and Factory default is 3 For example It is necessary to set code matching attempts number to 5 In engineer code programming mode press 1 1 LED1 blinks red buzzer and LED3 indicate current code matching setting then LED1 blinks red If current setting differs from 5 press red LED1 and green LED2 blink synchronously Press 5 the panel moves to upper menu level LEDs 1 and 2 blink red alternately LED3 is off To switch the panel to main mode press button LED2 blinks red 40 seconds pause between digits entry or cards passing causes panel switching to main mode Keyboard lockout time Press 1 2 when been in code parameters programming mode the panel reflects current parameters settings by means of buzzer and LEDs button pressing moves the panel to upper menu level To set new parameters press button and introduce time from 0 sec to 60 sec and press Factory default is 40 For example It is necessary to set keyboard lockout time to 10 seconds When been in programming with engineer code mode press 1 2 LED1
28. ol Panel Operation etit itt ro ORA A inser bas d ne k k 17 Programming the panel in access control system composition 18 Programming the panel in stand alone use ssssssee 18 Programmed information representation i eze 18 Programming Via PO o itinere teen teure i een sae nee k k da pea ud 18 Programming via built in keyboard ii kk kk kk kek 18 Factory defaults c 4 aee em prie tec tees Weide e ba vas Zan ba dak c n 18 Previewing and modifying users codes settings e 21 Code card deletion iisi iriiria ieiet eiee cob geeguitbesschectuveneeneetees 22 Resetting to factory defaults 23 Group card registration i i kk enm emen nene 23 Keyboard lockout time n dll pelka deka ladena kk nerd de kla dL n r da ked n 24 Peg 24 Door B WME m 24 Programming Inputs a ENE AE ennt nennen enn nere nennen nr nnne 25 Programming Outputs i sl xa ete trei tni deinde arek kan tre b ku h n d waa W sud 26 Types of identificators ren bes ise leeches cen ee esee ku KESA cei deste 27 Readers operation erint ete reece ees eves a e eranc REVE Ve de 28 Setting control panel address lllii Ek kk kk kk KA 28 Changing GOGe kandin a n ka Mea hee seit it eei ie debe ku id 28 Switching Day Night Modes iii kek ek kk kek k k kk KK KAK KK A KA 29 Resetting har
29. ombined one button jocis itis not recommended to use Z7 and Z8 terminals for combined cord connection Locking devices Lock of Access point A http www itvsystems com ua PWR TM NC1 C1 NO1NC2 C2 NO2 SA BEL 5 DLK642Lite has two relay outputs with NC and NO contacts They are used for connecting of power supply to executive mechanisms locking devices for instance Time and schedule of relay activating is programmed individually for every output with the help of engineer code Wiring of locking devices is shown on wiring diagram Relay contact rating is 5 Amp 24 Volts Integrated Technical Vision Ltd 13 Wiring Commutation of the inductive load electric lock for instance causes high energy electric impulse induced through relay contacts To save contacts from damage protect them with diode connected in reverse to current supply of the coil Note the fact that some cheap electric door strikes are not intended for being energized for prolonged time Program relay time as short as possible to avoid door strike coil overheat ing Sirens Bells and agents Some sirens require polarity observing WR NCI Cl NO1 NC2 C2 NO2 SA BEL Electric bells are often the inductive load for power supply During bells connection mind the warning about the inductive load above Bell Transistor outputs 12v up to 500mA There are two
30. ow LED2 blink alternately To proceed with other outputs programing press red LEDs 1 and 2 blink synchronously To move to upper menu level press again red LEDs 1 and 2 blink alternately LED3 is off To switch the panel to main mode press 40 seconds pause between digits entry causes panel switching to main mode 26 Integrated Technical Vision Ltd http www itvsystems com ua Programming the panel in stand alone use Types of identificators Press 2 0 in programming mode Green LEDs 2 and 3 reflect current settings LED 2 corresponds to ASK modulation identificators compatibility and LED 3 corresponds to FSK modulation identificators compatibility Then enter identificator type Identificators types 1 ASK identificators 2 FSK identificators 3 FSK and ASK identificators simultaneously For example It is necessary to program the panel for simultaneous utilization of ASK and FSK identificators When been in engineer code programing mode press 2 0 green LEDs 2 and 3 reflect current settings Press 3 new value is accepted the panel turns to upper menu level red LEDs 1 and 2 blink alternately LED3 is off Press button to exit the programming mode and turn to the main one LED2 blinks red Readers operation Press 2 1 in programming mode Green LEDs 2 and 3 reflect current settings LED 2 corresponds to external reader operation and LED 3 corre
31. rns panel to current code parameters programming Press to move to the highest menu level Next button pressing leads to exiting programming mode For example It is necessary to set access grant to door A relay 2 management and permit cardholder switch day night modes Press 2 in engineer code programming mode red LEDs 1 and 2 blink pass a card panel proceeds with card settings editing LED1 blinks red LED2 blinks yellow Press 1 switch on red LED2 and switch off LED3 by 4 and 6 buttons pressing Press LED1 blinks red LED 2 yellow Press 2 switch on red LED2 and off LED3 by 1 2 and 3 buttons pressing To switch day night mode the code card should have category 2 twenty four hour access Press 4 switch on LED2 with button 1 pressing press red LED1 and yellow LED2 blink alternately Press 5 then 2 red LED1 and yellow LED2 blink alternately Next button pressing turns panel to main mode Q Code card should have category different to 1 one for direct outputs management Users codes review and editing Press 3 7 being in code parameters programming mode then introduce code number or code itself The panel reflects user code card code with the help of buzzer sounds and LEDs blinking button pressing returns the panel to the highest menu level button pressing allows new user code introducing After new code card introductio
32. s a small company or a company that employs thousands Integrated Technical Vision Ltd http www itvsystems com ua Benefits Proximity reader and control system integrated into one small unit Easy to install surface mounted Can be attached for outdoor use RS485 networking Benefits Programming via own keypad or computer software One engineer code One master code Stand alone capacity of 998 users Read range of 15 cm with internal RF antenna Three LEDs provide visual annunciation Power consumption 80 mA to 130 mA Anti tamper switch reporting to network Features Two doors access control Three LEDs Nonvolatile EEPROM stores all settings and cards Two access levels Eight EOL supervised inputs for Door monitoring Request to Exit button and Alarm detectors monitoring Tamper Two relay outputs allow control of two doors Specifications Inputs Outputs 8 programmable EOL supervised inputs Two 5 A 24 V relays and Two 500mA 24V transistors open drain Networking Power consumption Supply Voltage Voltage ripple Standby current Maximal current Operation temperature Relative Humidity Physical Dimensions Weight http www itvsystems com ua RS485 interface 10 15 VDC 500 mV 12 V 80 mA 130 mA 0 C 55 C 80 relative at 35 C 155x95x32 mm 250 g Integrated Technical Vision Ltd 7 What s inside What s inside General Configuration Layout of DLK642Lite is show
33. sponds to internal reader operation Then enter readers operation mode Readers operation modes 1 external reader operation solely LED 2 2 internal reader operation solely LED 3 3 both readers simultaneous operation For example It is necessary to program the panel for external reader use When been in engineer code programming mode press 2 1 4 green LEDs 2 and 3 reflect current setting Press 1 new value is accepted the panel Switches to upper menu level red LEDs 1 and 2 blink alternately LED 3 is off At next 4 button pressing the panel exits programming mode and switches to the main one LED2 blinks red 40 seconds pause between digits entry causes panel switching to main mode Setting control panel address Press 2 2 in programming mode buzzer and green LED 3 indicate current panel address settings The panel turns to upper menu level after button pressing To introduce new settings press enter address from 0 to 31 and 4 For example It is necessary to set panel address for 8 In engineer code programming mode press 2 2 4 buzzer and green LED3 reflect current address setting Press 8 new value is accepted the panel turns to upper menu level red LEDs 1 and 2 blink alternately LED3 is off Press to exit programming mode and move to the main mode 40 seconds pause between digits entry causes panel switching to main mode http
34. ted time if lock output is programmed for 255 seconds Free pass Door opens at breaking of free pass cord Door is left open till shortage of the cord Free pass mode is indicated by LED2 blinking yellow and green light blink alternately Door blocking Door closes and does not open at door blocking cord violation and remains closed till cord shortage Control Panel Operation Autonomous operation Panel can operate in the following modes autonomously main mode z day night programming mode Red LED 2 blinks in main mode LED 1 is switched off in day mode and continuously switched on in night mode See Autonomous exploitation pro gramming chapter Panel grants denies access to cardholders in this mode or activates one of programmed outputs In order to switch day night modes use 1 command see Day night modes switching Operation in networked access control system Operation modes and indications are determined by the system during access control system work In external management mode the panel does not make independent decisions as for access assignment DLK642 Lite informs the master controller about all events and receives commands The panel turns into autonomous mode when connection to the master controller is lost All events are registered DLK642 Lite automatically turns to external management after connection to the master controller renewal Programming the panelin access control syste
35. trol panel to take instruction courses conducted by the ITV Systems company Technical support for all products of ITV Ltd can be obtained at business time by the phones 380 0 44 248 65 88 380 0 44 248 65 89 380 0 44 248 65 90 This support assumes the calls of trained specialists End users must apply to their dealers or installers before phoning us This information is available on our web site www itvsystems com ua http www itvsystems com ua Integrated Technical Vision Ltd 3 Integrated Technical Vision Ltd http www itvsystems com ua Contents Preface eo e b e e e b ue aS 6 Benellts 5 i E tecti eed ER Eie en daka RE ete a dak ela ed ea 7 Features sce REI ER adepti e dedu 7 Specifications mE 7 What s inside i naa eis xake nedye Ra eite idrico Derk r Sawak ra 8 General Configuration ri deie rev adan Ke R k deyk p v k 8 Wiring Configutations erret deeds ee ine Man wa VE Erg ee eee 9 Mounting citar ee eee XrD r 11 lager 12 Connecting readers EduE EEE keke e kk k k nennen KE A KAK KK KA KAK KA KA KK KA KA 12 PIN entry card passing xulek y d kaka Han tnnt kanan ke keza da 2R Ab KWE 15 Cardholders codes wi aeaeee ecrerb momomdmee em 15 D ress Code i cerr yay aa ade i ee ee ee ire des 16 Alarm OUtpUt 7 eee epDeADAe w uOr_x x lt lt a _ge r r 16 PED Sista CD EE 16 Door tIMe e 17 Gontr
36. ttings press then enter attribute number from 0 to 1 2 Outputs attribute 0 door A 1 door B Q Attributes are important only for type 1 lock output http www itvsystems com ua Integrated Technical Vision Ltd 25 Programming the panel in stand alone use Output time Press 3 after you have chosen number of the output the panel reflects current output time by means of buzzer and LED 3 The panel switches to output programming mode after button pushing To introduce new settings press then enter time from 0 sec to 255 sec 0 sec time setting corresponds to 0 2 sec output engaging Output operating mode Press 4 4 after you have chosen number of the output the panel reflects current output operating mode by means of buzzer and LED 3 The panel Switches to output programming mode after button pressing To introduce new settings press then enter operating mode from 1 to 4 2 Outputs operating modes are 1 start stop Output with ock type is switched off at opening of the door or at finishing of door time interval Output of bell or alarm type is switched off at ending of door blocking time interval or at breaking and shorting of Blocking or Free pass input 2 impulse Output is activated for a time set during programming 3 trigger Output is activated at each odd command and switched off at each even command 4 continuous Lock output is switched at
37. ype is set to the value from 1 to 17 or more than 19 the input is not used Inputs attribute 24 Press 2 you have chosen number of the input the panel reflects current input attribute by means of buzzer and LED 3 The panel switches to input programming mode after button pushing To introduce new settings press then enter attribute number 0 or 1 2 Input attributes 0 door A 1 door B Integrated Technical Vision Ltd http www itvsystems com ua Programming the panel in stand alone use Attributes are important only for door sensor or RTE button type of inputs The rest of inputs can be programmed as 0 attribute For example It is necessary to set input 2 as door B sensor In engineer code programming mode press 1 8 red LEDs 1 and 2 blink synchronously Press 2 red LED1 and yellow LED2 blink alternately now press 1 LED1 blinks red buzzer and LED3 reflect current input 2 type setting Press to proceed with input type editing red LED1 and green LED2 blink synchronously Press 1 8 new value is accepted red LED1 and yellow LED2 blink alternately Press 2 red LED1 blinks buzzer and green LED3 reflect current input 2 attribute setting Press to proceed with input attribute editing red LED1 and green LED 2 blink synchronously Press 1 new value is accepted red LED1 and yellow LED2 blink alternately To proceed with other inputs programming
Download Pdf Manuals
Related Search