User Manual - almetithalat.com
Contents
1. you turn on the power so it is convenient to use Eight Other functions ie Units shift Press and hold MODE button till Unit shining Press TARE button to confirm Unit shining again Then press the MODE button to select the unit that you like at last press TARE button to confirm Counting Pressed the MODE till Unit shining then press again Count shining Press the TARE button to confirm pcs shining Press MODE button pcs can change from 10pcs to 500pcs The larger the Numeral is the higher the counting precision is Put the counting goods correspondingly on the balance pan and press the TARE button to confirm It demonstrates After a while the counting is setted2. If the counted goods smaller than 2d it demonstrates no Cou and can t count In this case please choose several goods together as ONE goods 3 Percentage Pressed the MODE till Unit shining then press the button twice PER shining Pressed the TARE button to confirm 100 shining Then put the goods on the pan and press TARE button the goods is now setted as 100 Take off the goods and put another goods screen can show percentage If the percentage is too small less then 2d it doesn t work and only demonstrates no PER 4 Low voltage warning When the screen shows battery mark it means the rechargeable battery is lack of power lt 5 2V Over using will cause rechargeable battery s permonent damage and the weighing value will not be accurate 5 Change speed Press TARE button for 3 seconds Nine Charging 1 When you weigh goods daily please take away the AC adapter and use rechargeable battery only Otherwise even if the battery is full the AC adapter will still charge it 2 When you see low voltage warning put off the balance and charge it for 10 11hours better continuously Over charging is NOT recommend but will not cause big problem as our charging current is small 3 If you don t see low voltage warning please charge it for shorter time If you don t use or charge the battery for 6 months the battery will be fail 5 When replace old r
3. echargeable battery please adjust load cell s 4 corners tolerance at the same time gt Ten Pay attention to these points when using 1 warm up 10 minutes before using and calibration 2 The tare and objects to be weighed must not exceed the weighing limit 3 If the weighing results are not correct perform linear calibration twice 4 When replace old rechargeable battery please check load cell s 4 corners tolerance at the same time Eleven Product and accessories Electronic balance User s manual Remote display AC adapter Since product is continuously developing the information contained herein is subject to change without notice Electronic Balance Operating Manual 6 000g 0 1g 30 000gr 0 5g One Operating preparation 1 Set the balance stably on the horizontal table Avoid vibrating sunlight illumination air flow and strong electromagnetic wave Using environment Temperature boundary 5 C 35 C Temperature Fluctuation Range 5 C h Relative humidity 50 85 Two Turn on 1 Connect with AC adapter or use battery Press POWER button screen shows 8 8 8 8 8 8 Max capacity S CAL 0 00 in turns Three Perform calibration after 10 minutes warming up 1 Single point calibration Press CAL button for 3 seconds screen shows dA if shows others like d2 d3 d4 d5 d9 CALL please press CAL key again and again to make it show dA then 8000
4. g flicking then put 3000g weight sets on the pan thenitwillshow CAL then show 3000 00g then remove the weight calibration for 3000g point is finished This balance use our latest program when you perform dA 3000g single point calibration the effect performed 500g 1000g 12009 15009 1 700g 2000g 2200g 25009 27009 3000g linear calibration Because when you perform single point calibration the balance will automatically REMEMBER the linear calibration data performed last time 2 Linear calibration Press CAL button for 3 seconds _ it will show CAL L if it shows others like d2 d4 d5 d9 d A please press CAL button again and again to make it show CAL L then 500g flickering put a 500g standard weight on the pan screen show CAL then show 500 00g remove the weight calibration for 500g is finished then 1000g flickering automatically put a 1000g standard weight on the pan screen show CAL then show 1000 00g then remove it Cedies finally 3000 g flickering automatically put 3000g standard weights on the pan screen show CAL then show 3000 00g then remove it That is all If screen show no CAL means you didn t put weight on the pan in time If sceen show E100 that means your former calibration method is WRONG and original correct calibration data is DISAPPEAR In such case please cal
5. ibrate by above methods again Four Weighing 1 2 The value is stable when the black spot on LCD is disappear The Max weighing ability is the largest value show on the screen 9d Overloading will show upper horizontal line and damage load cell Five Tare Press the TARE button after the black spot on LCD is disappear Six Backlight Press BL button Seven Zero Tracking Function and Auto Tare Function only useful at 0 point or after tare When the power is off one hand press and hold CAL button meanwhile another hand turn on the power till Zero is displayed then press and hold TARE button till Zero d is displayed then press TARE button again the is changed from 0 to 5 Zero0d means balance 0 00g 3000 09g Zero5d means balance 0 05g 3000 09g When leave factory it is setted Zero5d Then press CAL button tArE is displayed then press TARE button tArE d is displayed then press TARE button again and again is changed from 0 to 9 tArEOd means without Auto Tare Function tArE9d means when there are 0 09g goods on the pan the program will eat it and only show 0 00g When leave the factory it is setted tArE9d Press BL button your setting is remembered and balance is restarted and will display 0 00 mode This electronic balance remembers your latest settings when
Download Pdf Manuals
Related Search