- UKDentistry
Contents
1. 12 Olident Ver 01 16 11 2012 Manufactured for Olident in eal GERMANY GERMAN 3 1008 QUALITY2. Contour with fine diamonds stones or burs Polish to high gloss with discs or rubber points Interproximal finishing is accomplished by fine grit finishing strips Storage Do not store above 25 C 78 F Protect from direct sunlight Do not use after expiry date Close syringe immediately after use to avoid exposure to light APPLIC Tips are for single use only Additional Notes e Do not use any resin to adjust viscosity of composite restorative material e Contact of resin pastes with skin should be avoided especially by anyone having known resin allergies e VITA is a registered trade mark of the VITA Zahnfabrik Bad S ckingen Germany Warranty Olident warrants this product will be free from defects in material and manufacture Olident makes no other warranties including any implied warranty of merchantability or fitness for a particular purpose User is responsible for determining the suitability of the product for user s application If this product is defective within the warranty period your exclusively remedy and Olident s sole obligation shall be repair or replacement of the Olident product Limitation of Liability Except where prohibited by law Olident will not be liable for any loss or damage arising from this product whether direct indirect special incidental or consequential regardless of the theory asserted including warranty contract negligence or strict liability Keep away from children For dental use only 20
3. Instructions for Use OliRevo Site 1 2 GB Esthetic low shrink light cure composite with nano filler technology OliRevo is a visible light cure nano filled composite for anterior and posterior restorations Beside its low shrink and low abrasion OliRevo shows improved handling features and excellent mechanical properties OliRevo is based on urethanedimethacrylate resin and inorganic filler particles lt 1 0 um The total filler content is 82 wt The composite material meets the requirements of DIN EN ISO 4049 Indications Suitable for all cavities Side Effects Irritations resulting from direct contact with the pulp cannot be ruled out Therefore for pulp protection the cavity floor in cases of deep excavations should be covered with a thin layer of calciumhydroxide material Incompatibility with Other Materials Do not use in combination with substances containing eugenol because eugenol can impair the hardening of the composite and causes discoloration Do neither store the composite material in proximity of eugenol containing products nor let the composite allow to come into contact with materials containing eugenol Preparation of Tooth and Colour Matching Clean the tooth with a fluoride free polishing paste e g flour of pumice with water prior to preparation and colour matching Ascertain the tooth shade while teeth are still moist and select the appropriate OliRevo shade OliRevo is shaded according to VITA Shades It is also avai
4. lable in special shades and bleach shades Cavity Preparation After isolation best with a rubber dam prepare the cavity with minimal tooth reduction Best pulp protection in case of deep excavations is the photo activated disinfection PAD If this is not possible deep excavations should be covered with a thin layer of calciumhydroxide material Condition and apply a bonding agent according to the manufacturer instructions The total etch technique with etching gel and subsequent application of a light cure bonding agent e g OliBond Ethanol is recommended Otherwise use a self etching bonding agent e g OliEtch Bond before application of the OliRevo Application and Curing of OliRevo Apply OliRevo in the selected shade OliRevo is easy to model Place it by using a suitable instrument Transparent matrix strips may be used In case of deep and extended cavities best results are obtained with a build up of a base liner using a light cure resin modified cement or a light cure flowable composite followed by the application of OliRevo In case of small cavities OliRevo can be applied directly For an optimum result apply OliRevo in layers of max 2 mm Light cure each increment separately By using a polymerization unit with a light intensity of at least 1000mW cm2 cure each increment as follows Instructions for Use OliRevo ste 2 2 E e Lighter shades e g A1 A2 C2 20 seconds e Darker shades e g A3 5 B3 30 seconds Finishing
Download Pdf Manuals
Related Search