Thermo Call TC3
Contents
1. Text message Function Description Factory command setting STOP The parking heater ventilation is switched 23 off or the pre selection time is deactivated STOPAUX STOP2 The analogue additional output is sa deactivated SUMMER The TC3 changes over from the heating to WINTER he ventilation mode WINTER The TC3 changes over from the ventilation WINTER o the heating mode AUTOMODE XX You can define a temperature between OFF 5 C and 35 C From the point at which he set value is reached the TC3 automatically changes over to the ventilation mode STATUS Shows whether or not the heating or the aes ventilation mode is active And if it is the remaining running time The same is shown for Output 2 The current temperature and on board voltage are also displayed TEMP The current temperature in the GSM as module or the cab temperature with an installed external sensor is transmitted The following 5 commands are only possible with an external sensor installed Text message Function Description Factory command TEMPSTATUS Shows the current temperature and the alarm status ON OFF for the upper and ower temperature threshold setting 1234LOTEMP XX Sets and activates the lower temperature hreshold An alarm is set off if the emperature falls below this value OFF 1234HITEMP XX Sets and activates the upper temperature hreshold An alarm is set off if this emperature is exce2. Jebasto Bedienungsanweisung Operating Instructions Thermo Call TC3 General Information Dear Webasto customer Thank you for purchasing the new Thermo Call TC3 This product provides you with a convenient innovative way to operate your Webasto parking heater These operating instructions supplement the explanations of the Webasto workshop or service centre carrying out the installation and the installation instructions and summarise the functions of the Thermo Call TC3 again A SIM card not included in the delivery scope is required to operate the unit Webasto cannot give any warranty for the SIM card used The function must be checked separately in individual cases For details on the SIM card please see the installation instructions of the product Please note that any data which has been saved on the SIM card will be deleted when commissioning the GSM module Use in areas close to the border or abroad may result in significantly higher costs due to roaming charges Please contact your network operator with regard to the operating costs incurred by domestic and foreign calls or text messages Operating costs are incurred by using the Thermo Call TC3 s feedback function and no liability can be accepted for these The feedback function can be deactivated You will find details in the list of possible text message commands Note These operating instructions only apply to Thermo Call TC3 with a firmware version from V3 2 For inform
3. amp Comfort SE 2013
4. of the SIM card installed in the TC3 The phone number used to call the TC3 must be saved beforehand in the unit see Text message commands After the connection has been successfully established the TC3 acknowledges the call with a tone e With the heater switched off the call is confirmed by the TC3 with 3 tones After the connection is disconnected the parking heating or parking ventilation operation starts for the set period of time factory setting 60 minutes The LED of the button integrated in the vehicle lights up e With the heater switched on the call is confirmed by the TC3 with 2 tones The respective operating mode is ended The LED of the button switches over to displaying the stand by mode Should the TC3 be called from a phone number not stored then the connection will be ended by the GSM module without feedback The respective heater operating mode remains unchanged 12 Operating with push button The delivery scope of the TC3 contains a push button which must be installed The push button is used both to operate the heater and to change the display of the current operating mode With the push button the heater can be switched on or off manually If the heater is operating when the push button is pressed then the respective current operating mode is ended The display can be deactivated if desired To do this press and hold the button for at least 5 seconds This procedure must also be carried out for reactivat
5. al phone XXXX 1234ACCLIMREMOVE numbers from which the TC3 can be activated via direct calling and text messaging At least the last 7 digits of the phone number must be entered to save the numbers However the country code and the area code can also be entered is even required for short phone number When several numbers are entered they must be entered in row without interruption and only separated by a colon For example 1234ACCLIMADD XXXXXXX XXXXXXX Where there is a later addition of one or more phone numbers these are added to the current store The maximum storage capacity is 15 phone numbers If the maximum storage capacity has already been reached Thermo Call TC3 sends back an error message Deletes a group of up to 5 phone numbers from the current store When several numbers are entered they must be entered in row without interruption and only separated by a colon For example 1234ACCLIMREMOVE XXXX In the process the phone numbers must be accurately entered as stored Please use the 1234ACCLIMLIST command for the list of all stored phone numbers Factory setting 1234ACCLIMREMOVE ALL Deletes all phone numbers from the current store For example 1234ACCLIMREMOVE ALL Warning Thermo Call TC3 cannot be operated again via direct calling and text messaging until new phone numbers are entered Please use the 1234ACCLIM XXXXXXX command to enter phone numbers Text message Program functi
6. ation see the marking on the GSM module Identnr 7100353 with Index C or higher Your Webasto parking heater or parking ventilation can be remote controlled by phone All mobile or fixed network phones with tone dialling are suitable for use as control units This enables you to operate a parking heater ventilation installed in your vehicle in the easiest possible way Not only the selection of the switch on duration but also pre programming of a starting time within the next 24 hours is possible Mobile applications Apps are offered for Apple Windows Phone 8 and Android smart phones These can be found on the respective markets The available descriptions are also available there Notes e Before commissioning the TC3 please observe the general operating instructions of your Webasto parking heater and the location of your vehicle regarding the establishment of a connection e Inthe heating mode the vehicle heater must be set to warm before leaving the vehicle In the heating and ventilation mode the vehicle fan switch is to be turned to position 1 in the case of 3 speed blower fans and to position 2 in the case of 4 speed blower fans In the case of infinitely variable fans adjust to at least 1 3 of the fan s capacity 11 Both with the Thermo Top E C and with the Thermo Top Evo heaters we recommend setting the heating time in accordance with the subsequent driving time to prevent discharging the battery With a driving t
7. eded OFF 1234LOTEMP OFF Deactivates the temperature alarm for the ower temperature threshold 1234HITEMP OFF Deactivates the temperature alarm for the upper temperature threshold 14 Text message command Function Description Factory setting 1234NBANK XXXXxX X Saves up to five phone numbers which will No phone XXXX be informed in case of a temperature number alarm an alarm of an optionally connected stored alarm system or in case of a failure malfunction of the external temperature sensor 1234I1BANK In this case any desired command max 20 Input active Entry command characters can be defined as to how the TC3 is to warn in case of an input signal from for example an optional alarm system e g break in alarm 1234DTMF ON Activates the DTMF tone feedback for a ON direct call 1234DTMF OFF Deactivates the DTMF tone feedback for a ON direct call 1234ACCLIM ON Activates the phone number restriction for ON direct calling 1234ACCLIM OFF Deactivates the phone number restriction ON for direct calling TC3 can be activated with any desired phone number 1234PIN XXXX XXXX_ Changes the access code from 1234 to 1234 XXXX 1234 is the factory setting for the access code and should be personalised by the user After this 1234 must be replaced by the personalised access code VERSION The firmware version is transmitted Text m
8. eplace if necessary Antenna error gt check installation location and cable routing and replace antenna if necessary rc m D flashes 3x cyclically PUK code error gt insert SIM card in a mobile phone and enter PUK and PIN code PIN code must be 1234 or must be deactivated Switch on GSM module again following power interruption LE D flashes rapidly approx 5x per second The TC3 has received more than 20 text messages within 30 minutes and was therefore automatically shut down gt press push button for at least 3 seconds This initialises the system can take up to 5 minutes D lights up Parking heater or ventilation has been activated D lights up however rking heater does t carry out command Potential problem with parking heater Contact your Webasto service partner D does not flash Button display is deactivated gt To activate press and hold push button for at least 5 seconds use same procedure to deactivate Faults LED signals readiness for operation however does not react to text message commands Description and remedy SIM card may have expired have been deactivated or may not have sufficient prepaid credit for a reply gt check SIM card with a mobile phone contact network operator or load credit TC3 does not react to direct calling although phone number is stored TC3 reports unknown message in reply to text m
9. essage command Program function description Factory setting 1234TIMER1 XXX Entry of the heating or ventilation duration between 001 and 999 minutes By entering 000 the respective operating mode is activated in the continuous mode and must be manually deactivated again by calling with the STOP text message command or by using the push button 60 minutes 1234TIMERAUX XXX 1234TIMER2 XXX Entry of the activation time between 001 30 minutes and 999 minutes Entering 000 activates the output in the continuous mode and must be deactivated manually with the STOP text message command 1234ASPONSE ON Each text message command is confirmed ON with a reply text message 1234ASPONSE OFF 1234ACCLIM XXXXXX x The reply text message is deactivated Saves up to 5 phone numbers from which Sun the TC3 can be activated with direct calling and text messaging At least the last 7 digits of the phone number must be entered to save the numbers However the country code and the area code can also be entered is even required for short phone number When several numbers are entered they must be entered in row without interruption and only separated by a colon For example 1234ACCLIM XXXXXXX XXXXXXX When adding one or more numbers later all numbers must be reentered Text message command Program function description 1234ACCLIMADD XxXxX Saves a group of up to 5 addition
10. essage command Phone has secret number phone number display is suppressed or SIM card problem gt activate phone number display or with SIM card problem check card ina mobile phone contact network operator or load credit Text message command faulty gt check text message command with regard to content and spelling No tone feedback to direct calling Phone number is not stored in TC3 gt see list of text message commands Not reply text message is sent by TC3 in response to text message command Feedback function is deactivated or prepaid credit may be insufficient gt activate feedback function or load credit 20 Bei mehrsprachiger Ausf hrung ist Deutsch verbindlich Die Telefonnummer des jeweiligen Landes entnehmen Sie bitte dem Webasto Servicestellenfaltblatt oder der Webseite Ihrer jeweiligen Webasto Landesvertretung In multilingual versions the German language is binding The telephone number of each country can be found in the Webasto service center leaflet or the website of the respective Webasto representative of your country Webasto Thermo amp Comfort SE Postfach 1410 82199 Gilching Germany Visitors address Friedrichshafener Str 9 82205 Gilching Germany Internet www webasto com Nur innerhalb von Deutschland Tel 0395 5592 229 E mail kundencenter webasto com Ident Nr 7100352C 08 13 Errors and omissions excepted Printed in Denmark Webasto Thermo
11. ime of approx 30 minutes one way we recommend setting a heating time of 30 minutes The GSM module is set to a heating time of 60 minutes at the factory The heating time can be set to between 1 and 999 minutes Continuous heating is also possible Details are provided on the following pages e You are recommended to change the Thermo Call TC3 s access code from the standard format of 1234 to a personalised one You will find details in the list of possible text message commands Operation and Programming Following entry of up to 15 authorised phone numbers the TC3 can immediately be operated with the factory settings For details on programming the phone numbers please see the following list of possible text message commands You have the following basic options for activating the Webasto parking heater Switching the parking heater or parking ventilation on or off directly with a phone call Switching the parking heater or parking ventilation on or off with a text message command e Pre programming the parking heater or parking ventilation within 24 hours with a text message command e Switching the parking heater or parking ventilation on or off with a push button The heater can be started via the heater control depending on its configuration Before parking the vehicle the settings required for the model must be carried out temperature fan Operating with a phone call Select the phone number
12. ion Various operating modes are displayed using the LED in the push button More information is provided in the list at the end of this document Operating with text messages The commands contained in the following list are sent to the TC3 via text messages The respective functions are activated or deactivated The commands must be entered in one word without spacing The use of upper case lower case characters is irrelevant The feedback function can be deactivated including for any entry errors A thermometer is integrated in the TC3 Temperatures specified in some feedback messages are guide values and may vary depending on the installation location Text message command for operation and programming XXXX Entry by the user Text message Function Description Factory command setting START Parking heater ventilation is switched on a STARTXXXX The start of the respective operating mode oa can be pre programmed once for up to 24 hours For example STARTO700 the respective operating mode is activated at 7 00 a m he following morning After sending the command you will receive a reply text message with the starting time current ime and temperature The starting time can be changed with a new text message or with the STOP command or can be deleted by pressing the push button for at least 3 seconds STARTAUX START2 The analogue additional output is activated sea for the programmed time
13. on description Factory command setting 1234ACCLIMLIST Feeds back a list of all stored phone numbers For example 1234ACCLIMLIST Warning You receive up to 3 feedback messages by text in groups of 5 stored phone numbers from the current store 1234SETDEFAULT Resetting to the factory setting The system is initialised within approx 5 minutes All customer specific data and entries are lost in the process and must be reentered The TC3 can be connected to an alarm system installed in the vehicle as an option When an alarm is triggered you will be informed via a text message if the function is activated For details please see the installation instructions of the TC3 18 Button feedback faults and remedies The TC3 was developed according to the latest state of technology and the mode of operation is extremely reliable Malfunctions are often due to the SIM card the network operator poor reception or incorrect operation Information of troubleshooting is provided in the following list Note The GSM module must be deenergised before removal of the SIM card Button feedback LE D flashes 1x cyclically every 2 seconds Description and remedy TC3 is ready for operation LE D flashes 1x cyclically every second 24 h pre programming is active LE D flashes 2x cyclically Network error gt contact network operator Error in SIM card gt check SIM card in a mobile phone and r
Download Pdf Manuals
Related Search