Network Camera VB-R11 Installation Guide
Contents
1. olimp 4 C C B Note Connect the cable after hooking around the tab to prevent accidental removal e LAN cable o T wrench gt Resetting the camera Remove the dome case and push in the power cable while pressing the reset switch Release the switch once the LED starts to flash When the LED stops flashing the reset procedure is complete ES O 1O Holm CC Ce E LED Removing the camera Remove the dome case and while pushing the mounting release button rotate it counter clockwise to remove Connecting the Camera Power Connection Power can be supplied to the camera in the three ways described below Please be sure to read the user manual for the dedicated power supply before use B Note e Power supply should conform to all local codes e The power supply should also comply with IEC UL60950 1 SELV LPS standards e The camera does not have a power switch Connecting and disconnecting the LAN cable PoE power supply AC adapter or external power supply plug turns the power ON and OFF respectively e When the camera needs to be rebooted perform the reboot operation from the camera setting page please refer to the Operation Guide gt Setting Page2. gt Maintenance E PoE Power over Ethernet The camera supports PoE functions Power can be supplied to the camera by using a LAN cable connected to a PoE HUB that conforms to the IEEE802 3at Type1 standard Important e Check with your dealer for more information about PoE HUB and Midspan technology Midspan a LAN cable power supply device is a device that like a POE HUB supplies power to the camera via a LAN cable e Some PoE HUBs allow the limitation of currents for each port but applying limits may interfere with performance If using this tyoe of POE HUB do not limit the operating current e Some PoE HUBs have limits for the total current consumption for the ports which can interfere with performance when multiple ports are in use For more information check the instruction guide for your PoE HUB e When the camera is connected to both a PoE HUB and an external power supply 12 V DC or 24 V AC power from the power supply first connected is given priority But when both power supplies are connected according to the combination problems such as failure of the network connection may occur When a problem has occurred either shut off the PoE HUB power supply setting or use the AC adapter that is sold separately as the external power supply E External Power Supply 12 V DC or 24 V AC input can be used Connect the power connector included in the package as shown below 12 V DC can be connected in a non polar config
3. Output terminal wi i _0O 1 Solid conductor AWG No 28 22 Conductor size 0 32 60 65 mm 0 013 0 026 in J Cable strip should be approx 8 9 mm 0 31 0 35 in Audio Input Output Terminals Each audio input output terminal only has one input system and one output system Connecting the camera to an audio input output device such as a microphone or a speaker with an amplifier allows you to send receive audio through the Viewer Use the 3 5 mm 90 14 in monaural mini jack connector to connect an audio input output device E Audio Input Terminal Common LINE IN MIC IN monaural input Although the camera only has a single audio input system it supports two types of microphone input LINE IN and MIC IN Before using the audio input please confirm the Audio Input on the Setting Page please refer to the Operation Guide gt Audio Input LINE IN is selected by default Input terminal 3 5 mm 90 14 in mini jack monaural e Dynamic MIC IN Input impedance 1 75 KO 20 Supported microphones Output impedance 400 600 Q e Condenser MIC IN Input impedance microphone bias resistance 2 2 KQ 20 Microphone power supply plug in power voltage 1 8 V Supported microphones Condenser microphones with plug in power support e LINE IN Input level Max 1 Vp p Use a microphone with an amplifier E Audio Output Terminal LINE OUT monaural output Connect the camera to a
4. Max approx 9 2 W Approx 1990 g 4 39 Ib Storage Environment Installation Method Power Supply Power Consumption Weight Before installing the camera Set the IP address and other network information on the camera using the Camera Management Tool on the Setup CD ROM For details on how to operate the Camera Management Tool please refer to the Camera Management Tool User Manual Dome case attachment detachment method Dome case removal method Loosen the dome case lock screw with the dedicated wrench and rotate it counter clockwise to remove it Dedicated wrench Attaching the dome case 1 Align the marks on the camera and the dome case and turn it clockwise to attach it 2 Tighten the dome case lock screw with the dedicated wrench Remove the dome case and place the memory card in the memory card slot To remove the memory card push it in all the way until the card slightly pops out and remove Important e Insert a memory card before installing the camera e When using a memory card with the camera for the first time it is recommended to format the card after inserting it into the camera please refer to the Operation Guide gt Setting Page gt Memory Card e Always unmount the memory card before removing it please refer to the Operation Guide gt Setting Page gt Memory Card Memory card slot Using the Dome Unit sold sep
5. V S 2 im ise f ig ie ONEN on E 8 4 4 T F 1 Ceiling mount holes S 2 Junction box fixing holes 83 5 3 9 32 4 3 Ceiling mount holes position 4 Junction box fixing holes position Specifications Please refer to the installation procedures or the Appendix Specifications for specifications not listed below 85 7 3 3 8 03 4 Unit mm in Camera Lens 30x optical zoom 20x digital zoom lens with auto focus Viewing Angle For 16 9 aspect ratios Horizontal 58 4 W 2 1 T Vertical 34 1 W 1 2 T For 4 3 aspect ratios Horizontal 58 4 W 2 1 T Vertical 45 0 W 1 6 T Min Subject Illumination Day Mode color 0 03 lux F1 4 shutter speed 1 30 sec when smart shade control is off 50IRE ight Mode monochrome 0 002 lux F1 4 shutter speed 1 30 sec when smart shade control is off 50IRE When using the Dome Unit Smoked sold separately Day Mode color 0 06 lux F1 4 shutter speed 1 30 sec when smart shade control is off 5OIRE ight Mode monochrome 0 004 lux F1 4 shutter speed 1 30 sec when smart shade control is off 50IRE 360 continuous panning 180 ceiling mounted position 0 180 When the horizontal direction of the camera is 0 Pan Angle Range Tilt Angle Range Interface Network Terminal LAN x 1 RJ45 100Base TX auto full duplex half duplex Audio Input Terminal 3 5 mm 0 14 in mini jack conne
6. dome cover Canon AC Adapter PA V18 Dedicated AC adapter for this camera CANON INC 2015 Printed in Japan Symbols Indicating Safety Precautions This Installation Guide uses the following symbols to indicate important information the user should know in order to use the product safely Explanations are provided for each symbol so that users will understand the level of importance for each Be sure to observe these items Failure to follow the instructions accompanied by this symbol may result A Warning in death or serious injury r Failure to follow the instructions accompanied by this symbol may result in A Caution iiur p E Failure to follow the instructions accompanied by this symbol may result Caution a in property damage Important This symbol indicates important or restricted items B Note Safety Precautions Installation Precautions Contains reference information for operation or additional explanations Warning Do not install in the following places e Places in direct sunlight near heat generating objects or locations subject to high temperatures e Places near fire sources or flammable solvents alcohol thinner fuel etc e Humid or dusty places e Places subject to oily smoke or steam e Places subject to sea air e Confined or enclosed places Failure to do so may result in fire or electric shock Notes on Power Supply e Only use the dedic
7. speaker with an amplifier Audio can be sent to the speaker from the Viewer Output terminal 63 5 mm 0 14 in mini jack monaural Output level Max 1 Vp p Use a speaker with an amplifier Only for European Union and EEA Norway Iceland and Liechtenstein These symbols indicate that this product is not to be disposed of with your household waste according to the WEEE Directive 2012 19 EU the Battery Directive 2006 66 EC and or national legislation implementing those Directives If a chemical symbol is printed beneath the symbol shown above in accordance with the Battery Directive this indicates that a heavy metal Hg Mercury Cd Cadmium Pb Lead is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive This product should be handed over to a designated collection point e g on an authorized one for one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment EEE and batteries and accumulators Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources For more information about the recycling of this product please contact your l
8. BIE 7067 000 BIE 7067 ENGLISH Canon Network Camera VB R11 Installation Guide Please be sure to read the Safety Precautions section for correct use After reading this Installation Guide keep it in a readily accessible location for future reference This camera is for indoor use only Some cameras are not available in certain countries or regions Z N WARNING To reduce a risk of fire or electric shock do not expose this product to rain or moisture N Caution Request a professional installer for all installation work Never try to install the camera yourself Doing so may result in unforeseen accidents such as dropping the camera or electric shock Check Included Items Camera Template Installation Guide This document Setup CD ROM Warranty Card Ceiling Plate Notice Dedicated wrench Power connector Accessories The following accessories can be purchased separately as necessary Some accessories are not available in certain countries or regions Recessed Mounting Kit SR11 S VB Dedicated accessory used to install the camera recessed into a wall or ceiling Plenum Mounting Kit SR11 P VB Dedicated accessory used to install the camera recessed into a ceiling The part projecting out within the ceiling can be covered Pendant Mounting Kit PC640 VB Dedicated accessory is used to install the camera to the end of pipe that extends from high ceilings such as in big box stores Dome Unit DU10 S VB Smoked
9. arately Remove the dome case from the camera then remove the dome cover holder and dome flange and replace with the smoked dome Important e Take care when replacing so as not to scratch the dome cover Dome cover Smoked dome cover Dedicated wrench Installing the Camera o Direct mounting on ceiling a Template b Ceiling plate If the cables cannot be stored above a ceiling co If the cables cannot be stored above a ceiling made of concrete etc break the cutout section of the dome a N IN case using pliers to remove the section to guide the cables Cutout section Attaching to a junction box Attach the ceiling plate to the junction box after confirming the fixing holes locations with the external dimensions diagram Ceiling recessed mounting Mount using Recessed Mounting Kit or Plenum Mounting Kit each sold separately For details please refer to the Installation Guide included with the kit Ceiling pendant mounting Mount using the Pendant Mounting Kit sold separately For details please refer to the Installation Guide included with the kit 0 1 4 gt 2 5 cm 1 0 in Pass necessary cables for connecting the camera through the pipe Included with Pendant Mounting Kit Dedicated wrench c Interface cover d Safety wire Using an external power supply
10. ated AC Adapter sold separately for AC power e Do not set any heavy objects on the power cable or the LAN cable for a PoE power supply e Do not pull forcibly bend scratch or modify the power cable or the LAN cable for a PoE power supply e Do not cover or wrap the AC adapter sold separately with cloth or blankets Failure to do so may result in fire or electric shock The contents of this guide are subject to change without any prior notice Caution For installation or inspection of this camera consult the dealer where you purchased the product e This installation should be made by a qualified service person and should conform to all local codes e When installing make sure the surface is capable of withstanding the total weight of the camera and accessories and that it is sufficiently reinforced e Be sure to use installation screws designed for the type of surface the camera is to be installed e Periodically check the parts and screws for rust and loosening in order to prevent injuries and equipment damage due to falling items e Do not install in unstable places places subject to significant vibration or impact or places subject to salt damage or corrosive gas e Be sure to attach the safety wire when installing the camera Failure to do so may result in the camera falling or other accidents e Do not touch the edges of metal parts with bare hands e Take care not to catch your fingers w
11. ctor monaural Common for LINE IN amp MIC IN LINE IN connect to an amplifier microphone or MIC IN connect to a microphone w o amplifier Switch LINE IN MIC IN in the setting page Audio Output Terminal 3 5 mm 0 14 in mini jack connector monaural LINE OUT LINE OUT connect to an amplifier speaker External Device I O Terminal Input x 2 Output x 2 Memory Card SD Memory Card SDHC Memory Card SDXC Memory Card Compatible Recorded Content Log Video Event Manual ONVIF Timer Upload Frame Rate Max 1 fos JPEG ax 30 fps H 264 Use CLASS 10 cards Cards under CLASS 10 may not have sufficient performance for tasks such as video recording Others Operating Environment Temperature AC DC PoE 10 C 50 C 14 F 122 F Humidity 5 85 without condensation Temperature 30 C 60 C 22 F 140 F Humidity 5 90 without condensation Ceiling mount Canon will not guarantee proper operation if the cameras are installed on surfaces where the angle is more than 5 from horizontal or on walls because this will put a heavy load onto sliding mechanical parts and may affect durability PoE PoE power supply via LAN connector IEEE802 3at Type1 compliant AC Adapter PA V18 100 240 V AC sold separately External power source 24 V AC 12 V DC PoE Max approx 9 5 W AC Adapter PA V18 Max approx 9 6 W 100 V AC Max approx 9 8 W 240 V AC DC Max approx 8 8 W AC
12. ear the camera Do not leave LAN cables external power supply or the power connector for the AC adapter sold separately connected when the camera is not in use for long periods e Do not use flammable solvents such as alcohol paint thinner or benzine when cleaning the camera Failure to do so may result in fire or electric shock Serial 1 Dome case lock screw 2 Dome case 3 Interface cover lock screw 4 Interface cover 5 Power connection terminal 6 100Base TX LAN connector 7 Audio input terminal Common LINE IN and MIC IN 8 Audio output terminal LINE OUT 9 External device I O terminals 10 Reset switch 11 Memory card slot 12 Lens unit 13 Mounting release button External Dimensions Cover at open position RJ45 connector location 199 7 83 30 1 18 26 1 02 Unit mm in 165 6 50 Camera mounting tab ___ 8 2 0 32 10 4 5 b 0 18 2 4 4 5 0 18 1 s A tt Hp DiX g 6 ih o
13. hen installing Failure to do so may result in injuries Caution e Do not turn the camera rotator by hand e Do not install on an unstable surface Also make sure the camera is installed 5 or less horizontal e After turning off the power do not turn the power on again for at least five seconds e Take measures to remove static electricity before performing any procedures e f there is condensation please wait to power on until the condensation dissipates Failure to do so may result in malfunction e Take care not to damage wiring or piping Failure to do so may result in damage to peripheral items Important e We recommend the installation of a lightning arrester a surge protection device as a measure against failures caused by lightning strikes Refer to our website for details Precautions for Use Warning e f you discover defective conditions such as smoke strange sounds heat or strange odors immediately stop using the camera and contact your nearest dealer Fire or electric shock may result from continued use of the product e f thunder starts stop installation or inspection etc and do not touch the camera or continue connecting the cable Do not disassemble or modify the camera Do not damage the connecting cable Do not spray the camera with water or otherwise make it wet Do not insert foreign objects such as water or metal into the camera Do not use flammable sprays n
14. ocal city office waste authority approved scheme or your household waste disposal service or visit www canon europe com weee or www canon europe com battery CANON INC 30 2 Shimomaruko 3 chome Ohta ku Tokyo 146 8501 Japan CANON EUROPA N V Bovenkerkerweg 59 1185 XB Amstelveen The Netherlands
15. operation and Event display panel E External Device Input Terminals IN1 IN2 External device input terminals consist of two sets IN1 IN2 of two terminals with the negative terminals connected to the camera interior GND Connecting cables to the positive and negative terminals and opening or closing the circuit notifies the Viewer Important e When connecting sensors and switches connect terminals that are electrically isolated from the respective power and GND e Do not push the external device I O terminal button with too much force Doing so may cause the button to remain pushed in E External Device Output Terminals OUT1 OUT2 External device output terminals consist of two sets OUT1 OUT2 of two terminals The sets have no polarity Controls from the viewer can be used to open and close the circuit between the terminals Using optical couplers the output terminals are isolated from the camera s internal circuit The load connected to the output terminals should be within the following rating range Rating between output terminals Maximum voltage 50 V DC Continuous load current at or below 100 mA On resistance Max 30 Q oe ee Internal Connection Diagram 3 3 V 1kKQ OUT1 OUT2 5 External device Input terminal 5 T 0 1 pF IN1 IN2 B Note 5 i 7T g TD S E External device 1 Pes r o 1 Adaptive wiring for external device cables z i N E
16. uration Screwdriver Tightening torque 0 25 N m max Sio Important _ PD _ e The power supply should be within the following voltage range e 24 V AC Voltage fluctuation within 10 of 24 V AC 50 Hz or 60 Hz 0 5 Hz or less Current supply capacity of at least 1 0 A per camera 12 V DC Voltage fluctuation within 10 of 12 V DC Current supply capacity of at least 1 5 A per camera e When using a 12 V DC battery power supply be sure to connect resistors of at least 0 5 1 0 9 20 W in series to the power line e For an external power supply use a double insulated device RAS Approx 5 7 mm ES 0 20 0 28 in a Power connector EA included Recommended Power Cables Reference Cable AWG 24 22 20 18 16 Conductor size mm 0 52 0 65 0 82 1 03 1 30 in 0 020 00 026 60 032 60 041 00 051 12 V DC maximum cable length m 5 9 14 23 32 ft 16 4 29 5 45 9 75 5 105 0 24 V AC maximum cable length m 11 18 29 46 64 ft 36 1 59 1 95 1 150 9 210 0 Use UL cable UL 1015 or equivalent for 12 V DC or 24 V AC wiring H AC Adapter Please use the dedicated AC Adapter sold separately External Device 1 0 Terminals External device I O terminals consist of two input and output systems each Viewer can be used to check external device input status and control output to an external device please refer to the Operation Guide gt External device output
Download Pdf Manuals
Related Search