DiViS CHSM48016
Contents
1. 1 STOP KEY Select DISABLE or ENABLE for the REC STOP button In case of manual recording manual recording can be started and stopped by the REC STOP button This STOP KEY protects the system from unauthorized interruption of recording While it is set to DISABLE recording can not be stopped by REC STOP button 2 REC SETTING Configure recording conditions as below Resolution 2 NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL Quality VERY HIGH VERY HIGH VERY HIGH HIGH VERY HIGH VERY HIGH VERY HIGH VERY HIGH VERY HIGH VERY HIGH VERY HIGH STANDARD STANDARD STANDARD STANDARD STANDARD 7 V w 3838338388838888 SHE REC MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL Audio ON ON ON OFF OFF Resolution Select from FULL 4 CIF D1 HALF 2 CIF Half D1 or NORMAL CIF Quality Select from VERY LOW LOW STANDARD HIGH and VERY HIGH FPS Select from a recording frame rate from 1 to 30 on NTSC 1 to 25 PAL REC Select from MANUAL SCHEDULE EVENT OFF for recording type Audio Select ON or OFF for audio recording Lock Select ON or OFF to prevent overwriting for the specific channel This lock overrules overwriting under HDD setting Therefore it must be used for a short period of time with caution LOCK must be turned off to prevent recording2. 5 After the system is rebooted please check on the setting to make sure the version information is changed to the new version N 37 E Divis www DiViSDVR com Appendix 1 DIVIS CHSM48016 Specification Description Specification Input 16CH composite Video BNC Outout 2 Ch Monitor 1 Ch Spot 16 Ch Loop through 1 S Video 1 i VGA Output Max 1024x768 Input Output 16 Ch Input 2 Ch Output Display Full Single Quad 9 View 16 View and Sequential Mode Becordia NTSC 704x480 704x240 352x240 J PAL 704x576 704x288 352x288 Algorithm MPEG 4 for video G 723 for audio Embedded Linux Recording Playback Monitoring Backup amp Network at the same time Video Audio Resolution Compression O ep Operation Pentaplex System control Button Remote Controller Mouse Recording FPS Recording Speed 480 352x240 120 704x480 in NTSC Recording mode Alarm Selectable recording CH amp pre recording Event Motion Alarm In Relay Out 16 NO or NC Alarm Inputs 4 NO or NC Relay Outputs Normal x1 speed Fast Forward x2 x4 x8 x16 NTSC PAL Playback P Fast Backward x2 x4 x8 x16 NTSC PAL Playback speed 480 NTSC 400 PAL FPS Le Search list sorting support All alarm motion schedule and time 10 100 Base T TCP IP UDP HTTP SMTP NTP DHCP DDNS Neise Einaion Easy GUI Live Monitoring Remote Configuration PTZ control Backup and Playback Network 3 TARN 7 W
3. 3 ry Press this icon to enable the system lock same as LOCK on the front panel 4 g Press this icon to start manual recording same as REC STOP w on the front panel 5 wI Press this icon to enter PTZ Control mode similar to PTZ on the front panel PTZ control with USB mouse allows the user to operate the preset feature of PTZ camera in addition to the basic operation the feature needs to be supported by the camera Preset control Select a preset number 1 255 and move EJ set M fev x on gt i A m e deset positon Camera Select a camera number 1 16 to control Direction Move to respective direction Zoom Control zoom in and out Focus Control focus and 6 A Press this icon to enter search mode same as SEARCH on the front panel 7 Press this button to close this icon set for mouse operation N 35E Divis www DiViSDVR com 7 2 Mouse Operation on Search While playing back recorded data mouse operation is also available to control playback Click on any of red circled area to show icons under playback mode 1 Press this icon to select an audio channel to playback same as FUNC MENU amp on the front panel N j Li gt Press this icon to toggle between play and pause same as PLAY PAUSE E on the front panel Ci Press this icon to stop playback and back to search screen same as STOP on the front panel 5 Press this button to close this icon set for mouse
4. 11 STOP D This button stops playback and return to the data selection screen 12 FF This button controls fast forward speed under playback mode supports 2 to 16 times playback speed as pressed repeatedly Also it controls zoom in under PTZ mode 13 MENU This button is to enter main menu of DVR N 1 E Divis www DiViSDVR com 14 ESC This button is to return to the upper menu 6 Direction buttons and ENTER Button Direction buttons are to move LEFT RIGHT UP and DOWN in menu They also can be used while entering password ENTER button in the middle is to select save a lt A Aad gt j E 4 a if 3 f 7 1 if i i t il a FI I i tt i eh F a i i if all f I My V and apply parameters in the menu n F a 7 Power Button Power On Off button This Power button can be pressed to turn off DVR power When this button is pressed password is Q requested When right password is input to DVR DVR power will be turned off 8 USB 2 0 connector These 2 USB Connectors can be used for a mouse and a USB Memory device Device s will be automatically detected upon connection j f b 1 r 1 i i s i T i a C e L i d CLE E BEE E EE d i i oe Er T Conn T co m r L 1 16 Ch Video Input 16 channels of composite video inputs with BNC connectors DiViS CHSM48016 automatically detects video format NTSC or PAL at p
5. Direction and ENTER buttons work same as buttons on the front panel e STOP Stop playback STOP on the front panel e SEARCH PLAY Start pause playback PLAY PAUSE on the front panel e Frame Search backward or forward while searching or cancels selected segment while scheduling e REW FF fast backward or forward 2 to 16 times while searching or applies selected recording option while scheduling lt Special Function using F1 button gt 1 F1 ENTER Display system information video format HDD Info IP address version etc 2 F1 ESC Turn on off displaying motion detected area under motion or alarm recording only 3 F1 MENU Display audio channel selection for speaker output in live display mode or playback mode 4 F1 1 2 3 0 10 Select a Remote Controller ID Once the ID is selected only the DVR with corresponding Remote Controller ID will receive command It is applicable only for DVR units that have REMOTE ID configured refer to Chapter 4 3 System Setup a 18 Divis www DiViSDVR com 4 Main Menu Programming fm DVIS DVR hi 3 gt seren gt B cae recor E ICE co ioe Ea O CERI gt ESTERNI gt NE 4 1 Overview Main Menu Before using DiViS CHSM48016 for the first time it is necessary to initialize the system with information that need to be manually adjusted such as time and date password display mode recording mode
6. For a CLASS A digital device or peripheral the instruction furnished the user shall include the following or Similar statement placed in a prominent location in the text of the manual Note This equipment has been tested and found to comply with the limits fora CLASS a digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment Generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of the this equipment in a residential area is likely to cause harmful interference in which cause the user will be required to correct the interference at his own expense N 3 E ivis www DiViSDVR com Preface This document is a basic manual for the DIVIS CHSM48016 users The manual describes the appearance and name of products how to configure the system program and how to use the system Please review the whole contents before using DiViS CHSM48016 and access the product with caution The pictures and names of the products are subject to change depending on hardware upgrade However the Usages may be similar To open the system case and touch the inner parts for corrective maintenance a user should contact the place where he she purchased the products to get the hel
7. Ja 6 LAN port RJ 45 Pin Descriptions Pin description 6 8o 8 nousa
8. The video channel can be selected by channel selection buttons on the front panel or by remote controller On remote controller Ch 10 16 the 10 button may be used for the tenth digit For example press 10 and then press 5 to select Ch 15 2 Display 4 video channels at a time starting from Ch 1 4 By pressing the quad button repeatedly the display will rotate from Ch 5 8 to Ch 9 12 Ch 13 16 and then back to Ch 1 4 so on and so forth 3 9 Picture Display Display 9 video channels at a time starting from Ch 1 9 By pressing this button repeatedly the display will toggle between Ch 1 9 and Ch 8 16 VIDEO LOSS 4 16 Picture Display Display all 16 video channels in a 4 by 4 format www DiViSDVR com 5 Sequential Picture Display Mode Sequentially display all available video channels based on the display mode For example if SEQ button is pressed under the full picture mode display will automatically switches from Ch 1 through Ch 16 6 Live audio selection for speaker output WR P g Ri LR Y DiViS CHSM48016 allows recording audio per each channel of video inputs ee eee and audio outputs are available for only one selected channel at a time In at ka S GAY order to select an audio channel for audio output press FUNC a n and then a vt MENU E on the front panel F1 and then MENU on the remote controller ae Ke ugh 24 we It will allow the user to select an audio channel
9. between O and 16 or Mute to teas way Mean turn off the audio 1 Time information is displayed on top center of the screen 2 Camera ID is displayed on the bottom left of each channel 3 Recording status is diplayed on the bottom center of each channel 4 Video Loss is displayed on the center of each channel 5 Other Icons Displayed on the middle bottom of each channel and indicates Manual or Motion Alarm recording Key Lock A Displayed on the top left when the key lock is turned on Nomor BBL _ Dspiyedon the topiet when there is a cometon made enol ez IN ospearen the top eft under PTZ conto mode remote 1D I _ bisplayed on the 1op1ef if other 0 i selected on tne remote A 29 Divis www DiViSDVR com 5 3 PTZ Control Prior to control PTZ function of camera s proper camera and setting must be done 1 Select a camera to control PTZ using Channel Selection buttons 2 Press PTZ or ENTER button on the front panel to enter PTZ control mode press ENTER on the remote controller Depending on the security setting the user might be prompted for password verification Note that PTZ control can be limited by user authority PTZ mode icon E will be displayed on the top left corner of the screen 3 PAN TILT Press direction buttons to move cameras to respective directions 4 ZOOM Press FF or REW on the front panel to zoom in or out press on the remote controller 5 FOCUS Press PLAY PAUSE o
10. network configuration and so on In order to access Main Menu first press MENU a l button of front panel in DVR or equivalent button on remote controller If ADMIN LOCK is set to YES which is the factory default the user will be prompted for login as below First select a user enter password using 1 through 10 Buttons press 10 to enter 0 and press ENTER button to log in ENTER button is located in the middle of directional buttons Factory default passwords for all users are 1 Note Under the menu please use direction buttons to browse through options available Up A Down VY Left lt or Right gt Press ENTER Button which is in the middle to make a selection or get into the sub menu if available Press ESC to return to the previous menu after setting and to save the values of setup PASSWORD OK anal CANCEL 5 6 7 6 9 N 156 Divis www DiViSDVR com 4 2 DVR Menu Tree _ S Y o TERN DISPLAY RECORD SCHEDULE HARD DISK CAMERA ID Co Ga my ee Ww fK ETA ee T m Bie Ji C EE rm STOP KEY REC SETTING F CONNECT IP ADDRESS SUBNET GATEWAY DNS PORT PPROE TME ZOME MTP TIME SETTING DONS STATUS CAMERA NO CAMERA ID PTZ TYPE PTZ ID PTZ BAUD RATE PANMITILT SPEED KBD ID KBD BAUD RATE SEQ DWELL SPOT DWELL TIME DATE OSD CAM NO OSD VIDEO LOSS OSD POP UP DISPLAY ADJUST CH PRIVATE CH QUALITY SET QUALITY RESET SCH
11. selected channel on 2 audio outputs available es E Divis www DiViSDVR com 3 Product Description 3 1 Front Panel Connection Remote Controller USB Memory Driver 3 2 Rear Panel Connection 16 Loop Through outputs Cameras 1 16 Ch FAN i 1 S Video Output G F Vcl _ L A 2 Audio Outputs bs p r PTZ be 16 Sensor 4 Alarm DE RS232 Power aD Supply 12V 5 8 A 16 Audio Inputs 1 VGA Output LAN Ethernet 9 H Divis www DiViSDVR com 3 3 Front Panel Description CD Tray This place can hold various types of backup media A DVD rewritable drive is installed at default Jog and Shuttle Jog and shuttle enables user to operate DVR easier in handling such as fast forward fast reverse playback and one frame movement in still picture 3 LED Indicators D Power LED turns on red when power is on ate Network LED turns on green when a connection established remotely one gt O Copy LED turns on green while copying data to CD DVD or USB device O Record LED turns on red while recording images O Key Lock LED turns on yellow if Lock function is enabled gt Remote Controller Receiver sensor input window for remote controller Channel Selection Buttons These buttons from Ch 1 to Ch 16 allow user to select a specific channel to be displayed on the monitor COCOCCLAO L IJ J JJ noc EIN J NM 5 Function
12. 255 0 GATEWAY 192 168 1 1 DNS 205 214 51 16 PORT 10000 10020 PPPOE ID lt NONE gt TIMEZONE GMT 8 Pacific U S A NTP TIME SYNC E DDNS STATUS STATUS OK URL 11797509 goddns org 1 CONNECT Select a connection method among STATIC DHCP or PPPOE 2 IP ADDRESS SUBNET GATEWAY DNS Accessible only if CONNECT is set to STATIC While accessible information can be changed to fit in the network environment Proper information must be provided from the network administrator or service provider Otherwise IP ADDRESS SUBNET GATEWAY DNS will be automatically assigned 3 PORT Select a TCP port number to use for the system This port number should be provided to users to make remote connection Once a port number is assigned DVR system would acquire next 20 consecutive ports too Therefore if TCP port 10000 at default is selected the DVR system will use TCP ports range of 10000 to 10020 and these ports should be opened and forwarded to the DVR system For the configuration of network devices please contact the network administrator or service provider 4 PPPOE Display PPPoE ID if available Only accessible and required if CONNECT is set to PPPoE Once selected and ENTER is pressed it will prompt to enter proper ID and password 5 TIME ZONE Select a proper location from the list The list is in increasing order by GMT There might be multiple choices available under same GMT In such case please make a most preferred pla
13. Buttons FUNC LOCK PTZ COPY ALT ile a iH A elile HE io BHE aleea ee 1 FUNC This button enables additional features for other buttons when combined FUNC ENTER Display system information video format HDD info IP Address version etc e FUNC MENU Opens interface to select a channel for audio output FUNC ESC Turns on off motion detection display for channels with motion recording ae 108 Divis www DiViSDVR com 2 3 4 5 6 7 8 9 e Apply All Button In the Event Setup Recording Setup select one setting value and press FUNC 1 to apply the same setting value to all channels LOCK This button enables key lock for the DVR unit Once pressed yellow key lock LED turns on and all features and settings are not accessible unless it is unlocked first To release key lock button locking press this button again and password is required to release While DVR is under key lock mode the icon will be appeared on the left top corner of monitor a PTZ This button enables control mode for PTZ Pan Tilt and Zoom camera s If available PTZ camera s must be properly wired and configured first While it is enabled select a camera that is configured for PTZ and press direction buttons to pan and tilt lt a gt to zoom in and zoom out Press PTZ button again to exit from the control mode after usage While DVR is under PTZ mode the icon wil
14. Change Camera ID to be displayed for the selected channel Once selected On Screen Keyboard will be available 3 PTZ TYPE Select a type of PTZ protocol if applicable In order to control PTZ cameras from the DVR system and remote it is necessary to properly set this section DiViS CHSM48016 supports following protocols DiViS D Panasonic Pelco D Pelco P Techwin Niko DRX502A DSC230s KRE 302 301 GC755NP TOA CC 554 RAS716 LS LPF100 KD INTR M LILIN MLP2 and so on 4 PTZ ID Configure the camera ID between 0 and 255 This ID needs to match with the physical ID set on the camera mostly by dip switches 5 PTZ BAUD RATE Baud rate for the camera connected Ranges from 2400 to 19200 BPS and needs to match with the actual camera setting 6 PAN TILT SPEED set pan tilt soeed between 0 and 10 higher number for faster movement 7 KBD ID Configure the keyboard ID between 0 and 16 This ID needs to match with the physical ID set on the keyboard 8 KBD BAUD RATE Baud rate for the keyboard connected Ranges from 2400 to 19200 BPS and needs to match with the actual keyboard setting Es 27E Divis www DiViSDVR com 5 Live Display amp Recording DiViS CHSM48016 supports full picture quad picture 9 picture and 16 picture view along with sequential switching mode Also it supports event popup if motion or alarm event is configured 5 1 Live Picture Display Mode 1 Display a selected video channel in full screen mode
15. DiViS CHSM48016 Stand Alone DOERNER RIKECIO Rev 2 0 h V a lt DIVIS Digital Video Security System Digital Video Recorder www DiViSdvr com E chance i USA Corp All contents of this document may change without prior notice and actual product appearance may differ from that depicted herein www DiViSDVR com Safety Precaution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This label may appear on the rear of the unit due to space limitations The lightning flash with arrow point symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of importance operating and maintenance servicing instructions in the literature accompanying the appliance Warning To reduce the risk of fire or electric shock Do not expose this product to rain or moisture Do not insert any metallic object through ventilation grills Power disconnect Units with or without ON OFF switches have power supplied to the unit whenever the power cord is inserted into the main source To disconnect it
16. EDULE Weekly SET Daily SET OVERVYRITE FORMAT HOD INFO LANGUAGE VIDEO FORMAT PASSYYORD ADMIN LOCK SUB USERS REMOTE ID TIME FORMAT DATE FORMAT DATETIME SET UPGRADE FACTORY RESET SETUR SETUP 2 MOTION AREA CH MOTION AREA DEVICE WATERMARK COVOVD EW FORMAT BACKUP INFO N ic Divis www DiViSDVR com 4 3 System Setup LANGUAGE ENGLISH VIDEO FORMAT PASSWORD ADMIN LOCK SUB USERS REMOTE ID TIME FORMAT 12HOURS DATE FORMAT MM DD YY DATE TIME SET 08 29 2008 03 01 13 PM UPGRADE VERSION 1 5 4 164NECI b4 FACTORY RESET a System Setup allows the user to set basic system configurations 1 LANGUAGE Select the language to be used on the system English German French Korean Turkish Italian Spanish Portuguese Polish and Russian are available 2 VIDEO FORMAT Display the type of video inputs NTSC or PAL which is automatically detected after power ON For proper detection it is strongly recommended to connect camera s while power is off 3 PASSWORD Allow the user to change current password of the user that is currently logged in with It will prompt to enter current new and confirm password Password can be assigned up to 8 digits of numerical combination Enter numbers using 1 through 10 Buttons press 10 to enter O Factory default passwords for all users are 1 4 ADMIN LOCK Allow the user to select YES or NO When YES login will pop up to access main menu search and con
17. EKLY SET B MONTHLY SET a 1 SCHEDULE Select WEEKLY or MONTHLY to enable scheduled recording Select OFF to disable recording by schedule 2 WEEKLY SET Allow the user to schedule by days of the week Each hour segment can be set to MANUAL dh or EVENT EY Press ENTER to switch between MANUAL and EVENT and use direction buttons to browse on the table Selected recording mode can be applied by buttons and canceled by mn buttons While using remote controller press to apply and 1 m to cancel 3 MONTHLY SET Allow the user to schedule by days of a month 01 through 31 Each hour segment can be set to MANUAL or EVENT and setting controls are same as WEEKLY SET above Note While setting schedule Func F 1 on remote controller toggles selection as following e FUNC 1 Apply selected value Event or Manual to all segments e FUNC 2 Cancel all and clear recording schedule e FUNC 3 Reverse selection Scheduled Event or Manual to blank and blank to selected value WEEKLY SCHEDULE MANUAL 14 00 14 59 fe 7 E 4 MONTHLY SCHEDULE EVENT 04 00 04 59 DB a Ged 6 9 06 6860660699000 4 6 898 0600900602060 0060666027600 2 4 6000684886888 026 OO 8 88 8 8 600606066 RARE AUO REJER AJE 0008006680000 66868908708 E MRR v A ccccecevecccevvcese N 23 B Divis www DiViSDVR com 4 8 Network Setup CONNECT DHCP IP ADDRESS 192 168 1 102 SUBNET 255 255
18. ORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL Sensor Select sensor type between NO and NC Input Select an input from 1 16 Out Select a relay output from 1 4 Buzzer Turn ON or OFF the audible warning upon event detection 2a aS BU OY OMAN he aa a www DiViSDVR com 3 MOTION AREA CH Select a video channel to set motion area to selectively detect motion 4 MOTION AREA Assign area to detect motion from 11 H x 10 V grid ENTER Toggle among direction mark add and remove on the circled area above Once it is set to add mark a currently selected segment will be marked to detect motion A segment will be deselected if it changes to remove mark Direction Buttons Move focus to the proper direction While the focus is set to direction mark the focus only moves to the direction that is pressed If the focus is set to add remove mark the focus will move to the proper direction and a segment will be selected or deselected respectively Change the channel to set motion area from Ch 1 to Ch 16 ESC Exit from motion area setting and returns to the event setup Note While selecting segment s for motion area Func F1 on remote controller toggles selection as following e FUNC 1 Select all e FUNC 2 Deselect all e FUNC 3 Reverse selection es 22 B Divis www DiViSDVR com 4 7 Schedule Setup SCHEDULE SELECT SCHEDULE 4 WEEKLY WE
19. R Menu Tree 4 3 System Setup 4 4 Display Setup 4 5 Recording Setup 4 6 Event Setup 4 7 Schedule Setup 4 8 Network Setup 4 9 Copy Setup 4 10 Hard Disk Setup 4 11 Camera Setup 5 Live Display amp Recording 5 1 Live Picture Display Mode 5 2 OSD On Screen Display on Live Mode 5 3 PTZ Control 5 4 Recording Options 6 Search and Backup 6 1 Search List 6 2 Search by Recording Type 6 3 Search by Time amp Date 6 4 Playback 6 5 Backup 7 USB Mouse Operation 7 1 Mouse Operation on Live Display 7 2 Mouse Operation on Search 8 Firmware Update Appendix 1 DiViS CHSM48016 Specification Appendix 2 Description of Terminals N 6 E Divis www DiViSDVR com 1 Product Contents At the point of purchase please verify that following contents are included e DiViS CHSM48016 16CH MPEG 4 Stand Alone DVR e Power Supply 12V 5 8A e Power cord e User s manual e Install CD e Remote controller two AAA batteries included DiViS CHSM48016 Power Supply Power Cord User s manual ip Install CD Remote controller SATA Cable 2EA 7 H Divis www DiViSDVR com 2 Features DiViS CHSM48016 is an embedded Stand Alone DVR based on Linux It is capable to record 16 channels of video and audio It is also capable to playback live display back up and network function while it is continuously recording And it also offers the following features e 16 composite video inputs 16 loop t
20. T video output which displays a single channel view of all connected video channels by sequentially switching Press Left Right Direction buttons to decrease increase dwelling time TIME DATE OSD Select ON to show the current time and date on the main display and OFF to hide Note that this setting will not affect to the time and date of recorded images CAM NO OSD Select ON to show the camera number on the main display and OFF to hide VIDEO LOSS OSD Select ON to display VIDEO LOSS with blue screen for disconnected input s If set to OFF disconnected channels will be displayed black POP UP DISPLAY Select number for the period in second to allow pop up display by event trigger such as motion or alarm Set to OFF to turn off pop up display If more than one channel needs to be popped up at the same time channels would be popped up by turn interval of 3 seconds ADJUST CH Select a channel to apply PRIVATE and CH QUALITY SET PRIVATE Turn on or off private feature on the selected channel The channel with private ON will display black screen CH QUALITY SET Adjust brightness contrast hue and saturation on the selected channel Once selected each attributes can be adjusted between 1 and 99 QUALITY RESET Reset quality controls including brightness contrast hue and saturation to the factory initial values A 108 Divis www DiViSDVR com 4 5 Recording Setup RECORDING SETUP STOP KEY REC SETTING 4 ENABLE E
21. ce per location 6 NTP TIME SYNC Select Yes to synchronized standard time using Network Time Protocol The appropriate time server will be referenced for the time zone assigned above To synchronize time recording must be stopped and DDNS Status must be OK which ensure the internet accessibility 7 DDNS STATUS Display Dynamic DNS status and address of it STATUS will display OK while normally connected NONE if DDNS is not used and ERR if DDNS IP update failure 2 6 Divis www DiViSDVR com 4 9 Copy Setup 5 DEVICE CDIDVD WATER MARK ON BACKUP LOG CDIDVD RW FORMAT E BACKUP INFO TSSTCORP CDDVDW SH S202N SB01 TOTAL 0 00 B FREE 0 00 B DEVICE Select a device to make a copy from USB Storage for USB memory device or CD DVD for optical drive Portable USB hard drives are selectively supported and those come up with storage size information may be used for a backup device WATER MARK Turn ON to put water mark while copying data Files with water mark can be verified for its integrity by the authentication tool available under File_ Player BACKUP LOG Copy log data file to the USB device It is only available while DEVICE is set to USB Storage Log information includes DVR power ON OFF recording time and event time If there is no BACKUP media No BACKUP media message will be displated Once the log file is created the file can be reviewed from notepad or any other text editors CD DVD RW FORMAT Execut
22. cluded can be used for the voltage between 110V and 240V Connect it to the outlet with the ground terminal Discard the vinyl bag well as it may be dangerous under a child s hands 2 Warning on Usage For the repair contact the company or the place where you purchased the product Read the user manual before using the products Do not open the cover at your discretion since parts are sensitive to the environment within the equipment Arrange the power cord safely and do not touch it with wet hands Do not use a loose outlet or a damaged power cable Do not use benzene thinner and alcohol for cleaning Do not touch the exposed terminal To properly turn off the system use the power button on the front panel before disconnecting the power supply Be careful to prevent a conductive object from falling into a hole that was punched for ventilation Do not disassemble nor remodel the product Do not place a heavy object on the body Handle with care while moving the equipment In case of any smoke or odor emitted immediately block the power switch and contact the company you purchased the products to consult it with a special technician N 5 B Divis www DiViSDVR com Contents 1 Product Contents 2 Features 3 Product Description 3 1 Front Panel Connection 3 2 Rear Panel Connection 3 3 Front Panel Description 3 4 Rear Panel Description 3 5 Remote Controller 4 Main Menu Programming 4 1 Overview Main Menu 4 2 DV
23. dicates available video and audio data for the channel Option Choose channels to backup and make sure SELECT size i FREE 0 00 B DELES Paes ia does not exceed FREE size i CHOS CH10 4 16 00 Move to the check mark and press ENTER to finalize CH11 v mehan backup CH13 y CH14 lt Note Backup File Player will be automatically copied to CHIE v the CD with files Files can be reviewed by Backup File CHG lt Player and File Player is also able to palyback those files however File_Player will create index on those copied files to playback Please refer to the description ofFile Player on the software manual N 3488 Divis www DiViSDVR com 7 USB Mouse Operation DiViS CHSM48016 supports USB Mouse to control the unit along with the front panel buttons and the remote controller For the convenience connect a USB mouse which is not included to the port available on the front panel All icons under main menu are accessible with mouse 7 1 Mouse Operation on Live Display On the Live Display locate the cursor to any of red circled area and left click to bring up the menu bar i ath P Olg gt mes j u m C e KEE E a a gt a ola o os 1 E Press this icon to open Main Menu same as MENU amp on the front panel 2 5 Press this icon to select an active audio channel same as FUNC MENU Bl on the front panel
24. e press FUNC and then MENU on the front panel F1 and then MENU on the remote controller It will allow the user select an audio channel between O and 16 or Mute to turn off the audio while playing back N 33 E Divis www DiViSDVR com 6 5 Backup From search list select desired option and date to search and press ENTER Then the Calendar can be browsed by direction buttons Make a change on date selection if desired and press ENTER again The following screen displays DATE 2006 START 2008 END 2005 M NL 0 NL MA AMR MG M7 8 IN TE 17 159 A I GA ITNA so 28 28 From the above screen press COPY on the Front Panel and USB button on the remote controller START and END will be prompted to set date and time to backup in order of year month day hour munite and second Set desired time range move to the check mark and press ENTER START 2007 086 01 16 00 27 END 2007 08 O11 17 00 00 Note On DIViS CHSM48016 recorded data is managed in the unit of each hour Copy start time and end time should be within same hour frame For example if 9 50 AM 10 05 AM needs to be backed up the user must perform copy twice once for 9 50 00 AM 9 59 59 AM and then 10 00 00 AM 10 05 00 AM Finally the user will be prompted with the menu below which displays free space of currently selected backup device size of selected data to copy and available data per each channel Icons next to each channels in
25. e media format Before make a copy of recorded files it is recommended to format the media if it is rewritable and not empty The built in optical drive will support most CD R CD R W and DVD R W BACKUP INFO Display media and connected device information Note Backup File Player will be automatically copied with copied data files The application is simple version of File Player For the usage of Backup File Player please refer to the description of File_ Player on the software manual For actual Copy Backup procedure please refer to chapter 6 5 Backup page 34 N 256 Divis www DiViSDVR com 4 10 Hard Disk Setup OVERWRITE ON FORMAT HDD E INFO 1 HDD TOTAL 68 49 GB FREE 49 10 GB 1 OVERWRITE Turn ON or OFF the overwrite feature It will recycle the HDD by overwriting oldest files by its maturity First recorded area in HDD can be replaced with new recording data 2 FORMAT HDD Execute formatting HDD Once the formatting is done Format Complete message will be displayed 3 INFO Display installed HDD information including a number of HDD installed total HDD capacity mounted and available space on it 2299999999272922 28 Divis www DiViSDVR com 4 11 Camera Setup CAMERA NO CAMERA ID Pis PTZ TYPE PELCO D PTZ ID 01 PTZ BAUD RATE 2400 BPS PAN TILT SPEED 07 KBD ID 00 KBD BAUD RATE 2400 BPS te e e e ee ee 1 CAMERA NO Select a camera to adjust ID or PTZ settings below 2 CAMERA ID
26. eb IE viewer Event Notification Multi user accessing Two way audio support CMS software Time Setting Network Time Protocol Support Pan Tilt Zoom RS485 USB 2 0 Firmware Upgrade via USB System log file USB Memory drive USB HDD backup F W upgrade Network USB2 0 Firmware Upgrade via USB network Electrical Power Supply AC to DC Adapter 12V 5 8A 38 H Divis Frame rate Recording Duration 30sec 1 2 3 4 5 6 7 8 9 10 20 30 40 50 min www DiViSDVR com Appendix 2 Pin Description of Connectors 1 USB Pin Descriptions Front panel 2 VGA Pin Descriptions Pin NO Slave Unit like PTZ Camera Pin description gt a DVR H RS485 D RX 2 RS485 D RX TX RS485 D TX __ 39 Divis www DiViSDVR com 4 Alarm Inputs amp Relay Outputs Pin Descriptions 12 3 40 5 6 7 6 GH 98 10 14 12 GW 13 14 15 16 GND NOI NCI COM NO2 NC2 COM NOS NCI COM NOJ NCA COM GND D D GND Ea S es ALARM IN L ALARM OUT RS 485 lt Alarm Inputs Pin gt lt Relay Outputs Pin gt Pin description Pin description E s en common ___ 8 Sensor input 07 Pog Relay output NC3 og Sensor input 08 GNO Common N 408 Divis www DiViSDVR com 5 RS485 Pin Descriptions NORA COM NO NCZ COU NOU NCS CCM NOS WACO GND D D CAD T e J R8 485 DVR Slave Unit like PTZ Camera gt No gt PSD x __ gt Rsa85D RXx __
27. from the main source you have to disconnect the Power cord 2 H Divis FCC COMPLIANCE STATEMENT A CLASS A computing device subject to certification by the Commission shall be identified pursuant to Par 2 925 et Seq of the chapter In addition the label shall include the following statement This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Where a device is constructed in two or more sections connected by wires and marked together the statement specified in this Section is required to be affixed only to the main control unit The user s manual or instruction manual for the EUT shall contain the following statement or equivalent Caution Changes or Modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment If the EUT requires accessories such as special shield cables and or connectors to enable compliance with emission limits the instruction manual for the EUT shall include appropriate instruction on the first page of the text concerned with the installation of the device that these special accessories must be used with the device It is the responsibility of the user to use the needed special accessories supplied with the equipment
28. hrough video outputs Compatible with color NTSC or PAL and B amp W CCIR and EIA 170 Video e 3 composite video outputs 1 S Video output 1 VGA output e 16 channels of audio inputs 2 channels of audio outputs e High quality video display and recording NTSC 704x480 PAL 704x576 real time display e Compression MPEG 4 for video G 723 for audio e Multiple search methods date time or recording types e Real time recording and playback support 480 FPS recording and playback for NTSC at CIF image 400 FPS for PAL Pre recording by event e Continuous recording in disk overwrite mode e Pentaplex simultaneously monitor record playback back up and network e Easy back up to external devices DVD back up and USB 2 0 memory drive support e User friendly GUI menu operating with USB mouse e PTZ camera control support from the unit and remote access e 16 alarm inputs 4 relay outputs available e Various network functions Access through static IP dynamic IP DHCP floating IP or DDNS View live or retrieve recorded video via remote connection Change configuration from a remote location Support multi user access up to 5 users can be connected simultaneously Support CMS Center Monitoring Software to access multiple sites at once Two way audio transmission and remote event alarm motion notification e Audio recording and playback Record 16 channels of audio inputs Playback 1
29. interruption Note Available FPS will be automatically adjusted according to video resolution setting Resolution All 16 Ch Max 480 Fps Max 400 Fps Available Recording Frame Rate NTSC 2 CIF Half D1 Max 240 Fps Max 200 Fps 4 CIF Full D1 Max 120 Fps Max 100 Fps CIF 320 x 240 in NTSC 320x 288 in PAL a 208 Divis www DiViSDVR com 4 6 Event Setup SETUP 1 SETUP 2 MOTION AREA CH MOTION AREA 1 SETUP 1 Quality Select the recording picture quality from VERY LOW LOW STANDARD HIGH and VERY EVENT Duration HIGH MOTION 1 MIN STANDARD ALARM 1 MIN STANDARD MOTION 4 MIN FPS Select from a recording frame rate from 1 to 30 STANDARD ALARM 1 MIN STANDARD ALARM 4 MIN on NTSC 1 to 25 PAL STANDARD ALARM 4 MIN STANDARD ALARM 1 MIN EVENT Select ALARM or MOTION STANDARD ALARM 1 MIN STANDARD ALARM 1 MIN f STANDARD ai Ried an PRE Turn Pre event recording ON or OFF When it is STANDARD ALARM 1 MIN Seances eee oe set to ON buffered images before the motion will be STANDARD ALARM 1 MIN recorded STANDARD ALARM 4 MIN STANDARD ALARM 1 MIN i i STANDARD ALARM 4 MIN Duration Assign recording time after the event triggered from 30 sec up to 60 min 2 SETUP 2 Sensitivity Select the level of sensitivity for motion detection from VERY LOW LOW STANDARD HIGH and VERY HIGH Sensitive Sensor Input N O 01 N O 02 NORMAL N O 03 NORMAL 04 NORMAL j 06 NORMAL 06 N
30. k information on monitor and file information in search list will be updated together DATE FORMAT Select MM DD YY DD MM YY or YY MM DD format to display date DATE TIME SET Allow user to change the date and time Setting a date and time prior to existing images date and time may cause corruption on recorded files Therefore it is recommended to set the date and time properly before start recording UPGRADE Display the firmware version Press ENTER to update the firmware through USB memory driver The firmware also can be updated over the network using Client software For more detail information Please check Chapter 8 Firmware Update Page 37 FACTORY RESET Return to factory default setting value Note When all of settings are finished and exiting from the main menu the user will be prompted as shown below Check box must be selected to apply all of changes made SS ie Wide N N r re Pron TT ia EE df aa z AEF 180 Divis www DiViSDVR com 4 4 Display Setup 10 SEQ DWELL SPOT DWELL TIMEIDATE OSD CAM NO OSD VIDEO LOSS OSD ON POP UP DISPLAY OFF ADJUST CH CH 1 PRIVATE NONE CH QUALITY SET QUALITY RESET e e ee e e e e SEQ DWELL Select dwell time between 1 to 60 seconds for the switching interval under sequential display mode Press Left Right Direction buttons to decrease increase dwelling time SPOT DWELL Select dwell time between 1 to 60 seconds for the switching interval on SPO
31. l be appeared on left top corner of monitor gt COPY This button initiate retrieving recorded files into backup media Depending on the device selected under setting selected data will be copied to USB Storage or CD DVD According to backup media proper icon will be appeared on the left top corner of monitor on Sequential Display button This button enables auto sequential switching under selected video display mode For example if this button is pressed under the quad mode the display will be switched sequentially from the quad picture of Ch 1 4 Ch 5 8 Ch 9 12 and then Ch 13 16 Display mode buttons Whenever these buttons are pressed display mode can be changed from the quad 9 Ch and 16 Ch display mode If the quad button is pressed again the display will be changed from the quad picture of Ch 1 4 Ch 5 8 Ch 9 12 and then Ch 13 16 as repeated For 9 Ch Button the display will be changed from Ch 1 9 to Ch 8 16 REC STOP This button starts and stops recording manually When DVR is under recording mode the icon will be appeared on each channel J SEARCH This button enters to the search mode Under search mode playback and backup are available REW This button controls backward speed under playback mode supports 2 to 16 times playback speed as pressed repeatedly Also this button zoom out under PTZ mode 10 PLAY PAUSE E This button starts pauses playback The button toggles between playback and pausing
32. operation gt Press these icons to control playback direction and speed 16 16 same as REW and FF on the front panel N 3 R Divis www DiViSDVR com 8 Firmware Update Important Note It is strongly recommended to update the firmware by a professional only if it is determined necessary Please make sure to review the whole procedure before start Do not power off the system or remove USB memory drive while the update is proceeding Update normally takes 10 to 15 minutes 1 Copy the new firmware file such as dvr535352xx tgz into a USB Memory Drive 2 Insert the USB Memory Drive into a USB port on the front panel 3 Enter Main Menu and select UPGRADE under System Setup refer to the Chapter 4 3 System Setup The following message will be prompted Select check mark and press ENTER LANGUA Gi WIJO RIGET ee PASSWOI ADMIN LO UPGRADE sua JSE REMOTE 4 wl Ea TIME FORMAT i 12HOURS DATE FORMAT MM 00 DATETIME SET 2006 09 22 09 44 03 PM UPGRADE VERSION 1 6 4 164NECI FAU TORY RESET 4 While update is in progress Please wait will be displayed and when it is done the system will be automatically reboot to complete update L PUIG AUG E VIDEO FORMAT PASSWORD ADMIN LOGA TIME FORMAT CATE FORMAT CATEMIME SET VERSION NO FATORY RESET UPGRADE LANGUAGE VIDEO FORMAT PASSWORD ADMIN LOCK TIME FORMAT CATE FORMAT DATEMIME SET VERSION HO FATORY RESET
33. ower on and both NTSC and PAL video sources are acceptable However type of video sources cannot be mixed All 16 inputs in a unit must have unique video format NTSC or PAL DiViS CHSM48016 will not operate properly if there are mixed video types 12H Divis www DiViSDVR com 2 10 11 12 16 Ch Loop through Outputs 16 channels of composite video outputs with BNC connectors that provide loop through video outputs Outputs may be connected as inputs to other video equipments if required 16 Ch Audio Inputs RCA 16 channels of unbalanced audio signal inputs with RCA connectors The audio input must be an amplified audio source such as amplified microphone 2 Ch Audio Outputs RCA 2 channels of identical audio outputs It is required to be connected to speaker headset or any other equipment as an audio input 3 Ch Composite Video Outputs and 1 S Video Output Two composite outputs MON 1 and MON 2 and S Video output provide main video output for live display and search They are same video output Another composite output SPOT provides a single channel spot monitor output that displays all connected video inputs one at a time sequentially Power Input Connect power supply DC 12V 5 8A RS232C To be utilized for future options VGA Outputs Provide RGB video signal that is identical with MON 1 MON 2 and S Video outputs Alarm Inputs 16 alarm inputs to connect with external devices to trigger various DVR event
34. p from expert In addition if there are any questions for use or any damage on the product please contact the place where he she purchased the products The pictures and names of the products are subject to change without notification However the usages may be similar For any questions you might have please contact us through the Service Request form available online When submitting your concerned matter please include your company name and phone number with detailed descriptions Service Request Link http www divisdvr com divis sp_ service asp Website http Awww divisdvr com N iB Divis www DiViSDVR com Warning on Installation and Usage 1 Warning on Installation Install the product on a flat floor open space and keep the minimum of 6 inches distance from the rear panel to the wall Install the product on a well ventilated place Keep it away from strong magnetism or electromagnetic wave Installing it near to radio equipment such as TV or radio may cause a malfunction Do not install it on a place directly exposed to the sun or other heating sources such as near a heating apparatus Do not install it on a cold place While installing the equipment keep the equipment and related tools in safe position to prevent any injury Do not install it on a place with constant vibration high humidity grease or dust Should use the product in the rated voltage The equipment requires DC 12V and the power supply in
35. r STOP on the front panel to adjust focus press m w on the remote controller 6 To exit from PTZ control mode press ENTER The PTZ mode icon will be disappeared 5 4 Recording Options DiViS CHSM48016 is capable to record 16 channels of video and audio simultaneously real time 80 FPS for each channel Also each channel can be independently configured for its resolution recording quality frame rate audio recording and so on Also recording mode can be selected individually Recording can be initiated by manually by triggered event of motion detection or alarm input or by weekly or daily schedule created by user Recording Mode Description Manual While recording mode is set to manual recording starts or stops by REC STOP button on the front panel or REC button on the remote controller Note that Manual recording enabled by schedule cannot be turned off by REC STOP or REC button Event While recording mode is set to event recording is triggered by event assigned for each channel from event setting Schedule Weekly While recording mode is set to schedule recording automatically starts or stops following the pre scheduled plan For weekdays Monday through Friday can be scheduled by 24 hours per day and each segment unit of an hour can be set not to record manual or event Schedule Daily From the first day of the month to the last day each days schedule can be planned and executed 30 H Divis w
36. s Mechanical or electrical switches can be wired as inputs The threshold voltage is 4 3V and the signal should be stable at least 0 5 seconds to be detected To make secure connections on the Alarm Connector Strip press and hold the button and insert the wire in the hole below of connector pin After releasing the pin pull gently on the wire to make certain it is connected To disconnect a wire press and hold the connector pin above the wire and pull out the wire Relay Outputs 4 relay outputs to send normally open NO or normally closed NC signal to external devices RS485 Connect to PTZ cameras to control through DVR system Ethernet Port RJ 45 Connect to the network to allow remote connection over the network Remote connection allows users to access live monitoring searching and other available functions via the network 2229999099797777 1368 Divis www DiViSDVR com 3 5 Remote Controller e REC Start and stop recording manually REC STOP on the front panel e LOCK Enable key lock LOCK on the front panel e USB Initiate backup COPY on the front panel e 1 2 3 0 10 Video channel selection buttons For channel 10 or above use 10 with other buttons e Display Buttons Top to bottom sequential quad 9 Ch and 16 Ch modes e F1 Additional functions with other buttons FUNC on the front panel e ESC Return to the upper menu ESC on the front panel e MENU Enter to the main menu MENU on the front panel e
37. s MENU button to search a specific date and time The following screen will be displayed Option NIN The user is able to select specific date and time to start playback Once the date and time are selected press ENTER to playback from that moment Refer to 6 4 Playback for detail instruction on playback N 32 ivis www DiViSDVR com 6 4 Playback While your DVR is in playback mode any video channel and display mode can be selected by channel selection buttons and display mode buttons lt Playback 9 CH gt lt Playback 16 CH gt 1 Play amp Pause Press PLAY PAUSE E button from the front panel to play and pause On the remote controller press Search PLAY to start play and Frame Search buttons w m to pause 2 Fast Forward and Rewind Playback speed can be controlled for x2 x4 x8 and x16 both forward and backward Press REW or FF on the front panel and E on the remote controller 3 Frame Search Once playback is paused the user can move frame by frame using LEFT and RIGHT direction buttons on the front panel or Frame Search buttons m on the remote controller 4 Jog and Shuttle It is convenient controller to control playback speed easily Works same as fast forward and rewind explained above 5 Live audio selection for speaker output DiViS CHSM48016 allows the user to retrieve video and audio simultaneously Similar to audio selection under live display mod
38. trol PTZ However some setting such as Sub Users cannot be adjusted if it is set to NO 5 SUB USERS Allow the user to change sub users name and authority accessibility There are 10 sub users available and only ADMIN user can access this setting to configure sub users In order to configure this ADMIN LOCK option above must be set to YES If it was just changed to YES please completely exit from the menu and log in as ADMIN user to access It is possible to configure each individual user permission to access setup perform search control PTZ remote in via network and change private option Note While changing the name of a sub user on screen keyboard will be available as shown on the left Press MODE to toggle between SPACE A different sets of characters BACK MODE OK Y CANCEL www DiViSDVR com 6 10 11 REMOTE ID Allow DVR unit to have specific and unique ID for remote controller If multiple DVR units are used within reachable distance a signal sent from a remote control will be delivered to all units reachable while the remote ID is set to OFF factory default The ID can be assigned from 01 to 16 After setting REMOTE ID the user must select the proper unit by pressing F1 any of 1 through 16 Once a unit selected other units will display following icon on the left top corner of the screen Q TIME FORMAT Select 24 HOURS military time or 12 HOURS AM PM Whenever Time Format is changed cloc
39. ww DiViSDVR com 6 Search and Backup option 6 1 Search List In order to search or backup recorded data press search button on front panel or remote controller 1 Option Select type of recording to display on the calendar among MANUAL EVENT SCHEDULE and ALL 2 DATE Allow the user to select date to search recorded data 3 GO TO Allow to access specific time to search This button is accessible with USB mouse only if available The feature is accessible by pressing MENU a button on the front panel or remote controller 4 Calendar Display days with available data based on OPTION selected The calendar displays the month that corresponds to the selected DATE 5 EXIT Return to the monitoring screen by exit button on the front panel or remote controller N 3 68 Divis www DiViSDVR com 6 2 Search by Recording Type From search list after selecting desired option and date to search press ENTER Then the Calendar can be browsed by direction buttons Make a change on date selection if desired and press ENTER again The following screen displays Option DATE 2005 06 NIIN VVi i Hit bia Manual Alann Motion Schedule 2008 08 22 23 30 00 w From the 24 hour time bar select a desired segment to search Recorded data are blocked in 15 minutes Once segment is selected press ENTER to playback Refer to 6 4 Playback for detail instruction on playback 6 3 Search by Time amp Date From Search List pres
Download Pdf Manuals
Related Search