H2i user manual
Contents
1. Front of Terminal Bottom of Terminal LED Indicating status of terminal and result of verification Green Terminal is in standby mode or verify users successfully Red Terminal has failed to verify user Fingerprint sensor To scan finger for confirmation of identity Card induction area Area that reads cards Speaker For terminal voice emission Reset button To restart the terminal as and when required USB port To connect a USB extension for data download into a USB flash disk pen drive To connect a USB Keypad to input numerical commands into the terminal optional gt CONTENTS 5 6 Bottom of Terminal Connect the external USB keypad to the bottom USB port of the H2i to insert a specific user ID number during enrollment or deletion You can also use the key pad to input commands to reset settings of the H2i back to its default factory set tings Refer to page 19 for details The external USB keypad is an optional item and is included in the package Security Features Security features help protect the information in the H2i from being accessed by unauthorized individual s ADMINISTRATOR CARD Registration of an administrator card to the system is important to control access into H2i After registration of the administration card is done nobody can do en rollment deletion or resetting on the H2i without the administration card TAMPER SWITCH H2i comes with a tamper switch2. Installation and Setup of Ingress Install Ingress in a PC that fulifills Ingress minimum requirements Refer to http www fingertec com customer download postsales SUM Ingress E pdf for the In gress user guide online Setup Wizard will require you to do online activation be fore connection establish between Ingress and terminals Connecting Terminal to Ingress THE FIRST TIME CONNECTION When connecting the Terminal to the Ingress for the first time you must use TCP IP to form the connection The Ingress allows you to configure the communication settings and the door lock settings An IP address is important as it is a unique address of the terminal in the LAN network Without an IP address locating the specific terminal is not possible Identify the number of your terminal to differentiate between one another The default IP address of the Terminal is 192 168 1 201 with the default terminal ID number being 1 The terminal ID can only be changed after you connect it to the Ingress Remember each Device ID must be paired with different IP addresses to indicate that it is different terminal gt CONTENTS Cc Monitoring Ingress Devices Doors Zone Ingressus Only Visual Maps Users Acd i 2 a BO a Scan n D Device j Devices Settings Enable Disabie 4 Devices E Devices Drag a column header here No DeviceName Serial Num Commu IPAddress Port Serial
3. located at the rear of the terminal During instal lation the tamper switch is compressed against a wall Any attempt to dismantle the H2i will trigger an alarm Restarting and Resetting H2i If something isn t working right try to restart or reset the terminal RESTARTING H2i Use a thin probe to push the reset button hidden at the bottom of the termi nal The terminal will restart by itself and all the memory is retained during this operation gt CONTENTS RESETTING TO DEFAULT FACTORY SETTINGS WITH AN ADMINISTRATOR CARD To reset the H2i back to its default factory settings you must first have the admin istrator card with you Green LED light blinks gt Wave Administrator card 5 times at the induction area gt Restore to default settings Please wave your administrator card to confirm gt Wave the administrator card to induction area to confirm gt si The operation is successful The system will return to verification mode Remarks All settings of the H2i will be reset to the default settings The IP address will be reset to 192 168 1 1 and the terminal ID will be reset to 1 after the process The administrator card information will be deleted from the memory and you will need to reenroll it However user information and trans action logs will still remain in the memory RESETTING TO DEFAULT FACTORY SETTINGS WITHOUT AN ADMINISTRATOR CARD Green LED light blinks gt Detach the terminal from the wall g
4. should rely on the contents of this publication without first obtaining advice from a qualified professional person The company expressly disclaims all and any liability and responsibility to any terminal or user of this book in respect of anything and of the consequences of anything done by any such person in reliance whether wholly or partially upon the whole or any part of the contents of this book FINGERTEC WORLDWIDE SDN BHD CONTENTS 23 2013 FingerTec Worldwide Sdn Bhd All rights reserved 072013
5. your card gt Wave card at the card induction area gt Terminal reads card and creates a new user ID gt e g User number 2 sf Registration is successful Register Please press your finger Remark Ignore this voice instruction if you do not intend to register a fingerprint in the terminal gt Wave administrator card an to induction area to end process gt sf System returns to verification mode Remarks 1 Repeat steps above to enroll new card users The system will automatically assign a user ID starting from number 2 By default User ID 1 is for an administrator card 2 If you would like to enroll fingerprint for the user after card registration continue with the steps below after you hear s Registration is successful Register please press your finger st Registration is successful Register please press your finger gt Press finger on scanner for first capture gt 6 Please press your finger again gt Lift the finger and press again on scanner for second capture gt s Please press your finger for the last time gt Lift the finger and press again on scanner for third capture gt Registration is successful Register please press your finger gt Repeat enrollment gt CONTENTS with other fingerprint if you want to enroll more fingerprint for the same user gt Wave the administra tor card at the induction area to end process gt si System returns to verification mo
6. 198 168 1 2 gt Press ENTER gt si key operation is successful gt Please enter the Subnet Mask gt Insert Subnet mask using keyboard example 255 255 255 0 gt Press ENTER gt key operation is successful gt s Please enter the Gateway gt Insert Gateway using keyboard example 192 168 1 1 gt Press ENTER gt sf key operation is successful gt 6 Please enter the Device ID gt Insert Device ID using keyboard example 2 gt Press ENTER gt si key operation is successful gt System returns to verification mode Restoring The Terminal to Default Factory Setting Plug keyboard to terminal gt The LED of keyboard lit up gt insert keyboard password gt a Password confirmation is successful gt Press button 3 gt Press ENTER gt Press button 3 gt Press ENTER gt sf Restore to default settings The operation is success ful gt The system returns to verification mode gt CONTENTS 5 OTHER RESOURCES COPYRIGHT NOTICE All rights reserved No part of this book may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying record ing or by any information storage and retrieval system without written permission from FingerTec Worldwide Sdn Bhd Every precaution has been made to supply complete and accurate information Information in this document is subject to change without prior notice DISCLAIMER No person
7. FING RIEC H2i FING RTEC H2i Simple Fingerprint Door Access amp Time Attendance System User Guide CONTENTS 3 4 5 7 18 22 CHAPTER 1 GETTING STARTED Viewing the User Guide in the Internet Included Accessories Included Printed Materials Activating H2i Registering H2i CHAPTER 2 BASICS Introduction to H2i H2i Overview Security Features Restarting and Resetting H2i CHAPTER 3 e CONNECTION SYNCING Installation Mount on Well Communication Description of Available Connections Ingress Online Activation Installation and Setup of Ingress Connecting Terminals to Ingress Using USB to Download Upload Data Communication Key CHAPTER 4 MANAGING USER Enrolling Administrator Card Registration of Administrator Card Enrolling User Cards Verifying Card for Attendance or Access Deleting Card User or Fingerprint User Operations with USB Numeric Keyboard Using the UBS Numeric Keybord Enrolling Users Deleting Users Configuring IP address Subnet Mask and Gateway by using USB numeric keypad Restoring The Terminal to Default Factory Setting 1 GETTING STARTED Viewing the User Guide in the Internet The User Guide is available in the package when you purchase FingerTec H2i The user guide is also published online at fingertec com and user fingertec com Choose the language you prefer to view the User Guide Included Accessories Door Accessories RS485 Wiegand Diod Cable Ou
8. NC or NO door lock a i TCP IP PORT Back of Terminal Ethernet Connection bd CONTENTS 9 FOR NC NORMALLY CLOSE DOOR LOCK SYSTEM DC12V Power Supply Optional to use with Diode Emergency break glass NC Key switch NC DC12V Power Supply Optional to use with Diode Release button Door Emergency sensor break glas NO Key switch B NO Please refer to AdapTec AC Installer Manual if you are using AdapTec AC 10 gt CONTENTS Descriptions of Available Connections USB PORT Linking with USB flash disk for remote data transfer 1 8 1 8 TCP IP PORT Connect with a CAT 5 cable for LAN connection one end to terminal s port and another end to the computer s TCP IP Port TCP IP for Single Connection JOINT 1 PIN JOINT 2 PIN Linking the terminal to a single computer using TCP IP TX 1 3 RX4 requires Ethernet 10 100Base T Crossover Cable The TX 2 6 RX cable can be used to cascade hubs or to connect Ether net stations back to back without a hub It works with both 10Base T and 100Base TX RX 3 e e1__ TX RX 6 e 2_ TX TCP IP for Network Connection Linking the terminals to multiple computers using TCP IP requires Ethernet 10 100Base T Straight Thru Cable or whips The cable works with both 10Base T and 100Base TX connecting a network interface card to a hub or network outlet CONNECTOR PIN CABLE COLOR CON
9. NECTOR TX 1 White Orange 1 TX TX 2 Orange 2 TX RX 3 White Green 3 RX qgoe Blue 4 5 RX pim Green 6 RX vA 8 White Blue 5 White Brown 7 Brown 8 POWER SUPPLY PORT Insert the Power Adapter point to this port for power RS485 WIEGAND INPUT CONNECTION PORT RS485 Single Connection Connection to a single computer using RS485 wire RS485 Network Connection Connection to multiple computers using Daisy Chain connection Wiegand Output Connecting with third party connector or terminal s gt CONTENTS 11 12 ACCESS CONNECTION Linking the terminal to door lock system BELL PORT Linking the terminal to doorbell Link all cables to the correct connection point s before attempting to connect the terminals to software Ingress Online Activation Ingress is a genuine software by FingerTec Every FingerTec access control model comes bundled with a unique license key To start using the terminal with Ingress you must connect the terminal to Ingress and perform online activation Ingress reads the serial number of your terminal and sends it for verification at the Fin gerTec server via Internet In case you do not have an Internet connection you would need to do offline acti vation Please send the serial number and models of your terminals to your local re sellers or support fingertec com to request for a product key and activation key
10. P Baudrate Add Device x At the Devices Tab user can ee Standalone Device Dinan either choose to add device Keylock via Add Device to individu Device Name Terminal x ally add or Scan Device to Communication Key add multiple terminals at one a E A E pies go For single terminal after T AT r Communication Mode filling in the relevant informa RAIDE a tion click Add and Continue ae 192 168 0 201 i to proceed by adding another oH 4370 terminal or Add to add only Device Activation online D offine one terminal add And Continue add For trial user with reader please enter your reader ip into the Ip URL text box for trial user without reader please enter the given 8 digits serial number into the IP URL text box lier cancel To add multiple devices at one go click Scan Device and Scan IP Address range can be set to search for devices The bigger the range of IP address the longer time needed to scan for devices Devices found will be displayed on the screen Select the preferred devices and click Add Selected Device to add them and a window contain ing the settings of the terminals will pop up Click Add to proceed gt CONTENTS 13 14 San Device x Device Type Ingressus Keylock IP Address Range 192 168 0 1 zi 255 Device Name IP A Add Device x Status M a n Device Name 192 168 0 201 F Auto Synchronize Device Ti
11. before any other operations could take place in a terminal Once an Administrator Card is available an administrator can perform these 3 major functions 1 Unlock a terminal for enrollment or and deletion of users with fingerprints or cards 2 Download data from a terminal with a USB flash disk 3 Reset the terminal to its default factory settings An administrator card cannot be used to report attendance or gain access it is solely used for the above operations To gain access or to report attendance an adminis trator must enroll his her fingerprint into a terminal afi The terminal is providing users with vocal instructions Follow the instructions carefully Registration of Administrator Card Power up terminal gt Red LED blinks gt s Please register the administrator card gt Wave card at the card induction area gt Terminal reads card and beeps once gt Registration is successfu gt System returns to verification mode gt The Green LED blinks gt Terminal is in stand by mode Remark If the green LED blinks when you power on the terminal it means that the terminal has already been enrolled with an Administrator card Find the administrator card to proceed or you need to reset the terminal in order to enroll with a new administrator card Enrolling Cards Users Green LED blinks gt Wave administrator card at the card induction area gt Register user Please press your finger or wave
12. ce record is captured and access is granted Remark If the terminal s red LED blinks with an instruction that says Please press your finger again it could mean two things The fingerprint might not be registered with the system yet or you did not place the fingerprint properly on the scanner Please place your finger carefully on the sensor with the center points positioned at the center of the scanner If the terminal consistently does not verify you it probably means that your finger has not been enrolled yet Contact the administrator to enroll CARD ONLY Green LED blinks gt Wave card at the card induction area gt sh Beep once gt 5 Thank you gt Green LED blinks gt Verification is successful gt Attendance record is captured and access is granted Remark If the terminal s red LED blinking coupled with two short beeps the card you are using has not been registered to the system yet Please contact an administrator for card enrollment CONTENTS 19 20 FINGERPRINT OR CARD Refer to the above explanation FINGERPRINT AND CARD Green LED blinks gt Wave card at the card induction area gt Terminal reads card and beeps once gt si Please press your finger gt Press finger to scan fingerprint gt Beep once gt sh Thank you gt Green LED blinks gt Verification is successful gt At tendance record is captured and access is granted Remark If the terminal s red LED blin
13. click on Reboot Device A window will pop up seeking confirmation on whether to restart the device Click Yes and the IP address for the terminal has been successfully changed Doors Basic Information Device Name 9 bo Serial Num 2301446 Firmware Ver 6 61 Apr 10 2013 Model H2i Information Network Biometric Power Access Control Other fF OP Log Other Clear All Device Data Clear All Log Synchronize Date amp Time Clear Admin Privilege Download Device Settings Upload Device Settings Activate Device gt CONTENTS Using USB to Download Data The USB flash disk feafure is useful in cases where the terminal is installed far from a PC or there is a connection problem To determine the type of USB compatible with the terminal please refer to this link at fingertec com newsletter HL_74 html USING USB FLASH DISK PEN DRIVE USB flash disk can be used in the H2i for these operations Downloading uploading user information user ID fingerprints cards etc e Downloading transaction logs 7 We highly recommend you to contact D Updating firmware support fingertec com for this operation The H2i comes with a USB extension This extension is intended for security purpose for without it no USB flash disk can be inserted into the terminal to access its data To carry out any of the above operations you must first plug the USB extension into the port in the terminal and then in
14. de It is recommended to enroll 2 fingerprints for each user but the system allows you to enroll up to 10 fingerprints for a user Enrolling Fingerprint Users Green LED blinks gt Wave the administrator card at the card induction area gt Register user Please press your finger or wave your card gt Press finger on scanner for first capture Please press your finger again gt Lift the finger and press again on scanner for second capture gt h Please press your finger for the last time gt Lift the finger and press again on scanner for third capture gt s e g User Number 3 gt Registration is successful Register please press your finger or wave your card gt Repeat enrollment with other fingerprint if you want to enroll more fingerprint for the same user gt Wave a new card to the induction area if you want to enroll card for the same user gt Wave administrator card to induction area to end process gt 5 System returns to verification mode Verifying Card Fingerprint or Both for Attendance or Access Please check that you have configured the correct verification method s i e Fin gerprint only Card only Fingerprint or Card Fingerprint and Card in the terminal through the TCMS V2 software FINGERPRINT ONLY Green LED blinks gt Press your finger on scanner gt sf Beep once gt sh Thank you gt Green LED blinks gt Verification is successful gt Attendan
15. en done click Save to confirm the changes made Basic Information Device Name t Firmware Ver6 61 Apr 102013 3601177 MKadex Information Network Biometric Power Access Control Event Communication Communication Mode Device ID TCP IP Setting 1P Address URL Gateway RS485 Setting Comm Port Communication Key Auto Synchronize Device Time Port Subnet Baudrate gt CONTENTS 15 16 Once done a popup window will appear indicating the update is successful Click OK to proceed The Ingress software has to be synced with all relevant devices in order for the changes to take effect A small window will appear at the bottom left corner of the screen once any changes are made Click on the underlined blue sentence to sync the terminals Any changes made will appear in the Synchronize Device Settings window Check Tick the changes needed to be synced to the terminals Click Start Synchronize once the selections are made Another popup window will appear displaying the changes made at the particular doors affected Click Start Synchronize once everything is confirmed Synchronize Device Settings x a MA Doors a M ia Front Door F Show All Doors E Auto Reboot Device After Synchronize Stat Synchronize Cancel E t 0 Once synchronization is complete click Close to proceed Go to Other tab and
16. he USB numeric keyboard to the USB extension and another end into the H2i for activation The following commands can be programmed into the terminal via the USB key board Enrolling new user by user ID Deleting user by user ID Resetting the terminal to default factory settings Deleting all users in the terminal Changing keyboard activation password nun BWN Configuring TCP IP setting gt CONTENTS Using the USB Numeric Keyboard ASSIGNING KEYBOARD PASSWORD Assign a password when you are using the keyboard for the first time This is impor tant to avoid unauthorized access into the terminal via keyboard Plug keyboard to H2i gt The LED of keyboard lit up gt The Green LED of H2i blinks gt Wave administrator card to the card induction area gt Please press the keyboard gt Press button 8 gt Press ENTER gt Press button 8 gt Press ENTER gt sf Please set password gt Press keyboard to insert a new password 4 to 6 digits for example 123456 gt Press ENTER gt si The operation is successful System returns to verifica tion mode Once the password has been created use the keyboard to control H2i With the keyboard you do not need to use the administrator card to control H2i Keep the password secure TO CHANGE THE KEYBOARD PASSWORD Plug keyboard to H2i gt The LED of keyboard lit up gt The Green LED of H2i blinks gt Insert your password gt s Password confirmati
17. king coupled with two short beeps neither the card nor the finger that you are using been registered to the system yet Please contact an administrator for card enroll ment Deleting Card User or Fingerprint User Green LED blinks gt Wave administrator card 3 times to the card induction area gt Delete User Please press your finger or wave your card gt To delete a card you need to wave the card at the induction area and to delete a fingerprint please place the particular fingerprint on the scanner gt si Beeps once gt sh The user ID of the card or the fingerprint for example user ID 2 gt 6 Delete User Please press your finger or wave your card gt The user has been deleted gt Repeat steps above to de lete the other users gt Wave administrator card to end process gt sf System returns to verification mode Remark 1 Each user is entitled to have one card only Therefore when the card user is deleted the user ID is completely deleted from the terminal 2 Each user can enroll a maximum of 10 fingerprints under one user ID A user has an option either to delete particular fingerprints or all fingerprints from a terminal Place the particular finger you want to delete on the scanner for the system to delete it Repeat the steps to delete all fingerprints Operations with USB Numeric Keyboard H2i terminal is packaged with a USB Numeric keyboard to manage users Plug one end of t
18. me 7 Select All None bow Once the device has been added a pop up window will appear indicating that the device has been successfully added Click Ok to proceed scan Device x Device Type Standalone Device I Keylock IP Address Range 192 168 0 1 255 Device Name IP Al Add Device x Status W SSSS Serial Num Device Name 192 168 0 201 i x Q Oh yeah Device added successfully Ex Online Offline Add And Continue add canca Activating device Select All None 100 l Add Selected Device an Close gt CONTENTS HOW TO CHANGE IP ADDRESS Terminal does not have a keypad thus to change the IP address users can do it via Ingress software Steps to change IP address via Ingress are as below Go to Doors tab and click on Add Door Monitoring Doors Zone Ingressus Only Visual Maps Users Ad E E ea 4 Door Time a Ho Group f Door Group Camera Permanent Door Open Close Timezone E Doors Drag a column header her M Permanent Door Open Close Ino Er RP don Once the door is added click on Add Device at the Doors tab Check Tick the terminal s to be added to the specific door Click OK Double click on the device At the Network tab click Edit Change the desired IP address at the IP Address URL column Wh
19. on is successful gt Press button 8 gt Press ENTER gt Press button 8 gt Press ENTER gt 5 Please set password gt Insert a new password 4 to 6 digits for example 456789 gt Press ENTER gt si The operation is successful System returns to verification mode Enrolling Users You can enroll users with fingerprints or cards without using an administrator card Use the keyboard to carry out enrollment operation in the terminal Plug keyboard to the terminal gt The LED of keyboard lit up gt The Green LED blinks gt Insert password via keyboard gt s Password confirmation is successful gt Press button 1 gt Press ENTER gt sf Register User Please input user number gt Insert user ID using keyboard gt System repeats the number inserted for example h User number 12345 Register User Please press your finger or wave your card gt Refer to Enrolling Card User Or Enrolling Fingerprint User for details of enrollment steps Deleting Users You can delete users from terminal without using an administrator card but by us ing a keyboard You can delete users by inserting their user IDs or delete all users in the system To delete particular user Plug keyboard to terminal gt The LED of keyboard lit up gt The Green LED blinks gt Insert keyboard password gt si Password confirmation is successful gt Press button 2 gt Press ENTER gt Delete User Please input User ID gt Inse
20. rt user number using keyboard gt Press ENTER gt System repeats the number CONTENTS 21 22 inserted for example user ID 12345 gt a Deletion is successful Delete User Please input user number gt Repeat to insert user ID to delete gt undetermined steps gt The system returns to verification mode To delete all users including the user for an administrator card Plug keyboard to terminal gt The LED of keyboard lit up gt Insert keyboard password gt s Password confirmation is successful gt Press button 9 gt Press ENTER gt Press button 9 gt Press ENTER gt Delete All Users The operation is successful The system returns to verification stage Please register the administrator card After the operation the H2i will be completely empty You must re enroll adminis trator card into the terminal to start over Configuring IP address Subnet Mask and Gateway by using USB numeric keypad In case you are going to install multiple H2i in an environment setting up IP ad dress to every H2i becomes troublesome Now you may consider using the USB numeric keypad to ease the job Plug keyboard to the terminal gt The LED of keyboard lit up gt The Green LED blinks gt Insert password via keyboard gt Password confirmation is successful gt Press button 4 gt Press ENTER gt s Please enter the IP address gt Insert IP address using keyboard example
21. sert the USB flash disk into the other end of the extension Listen to the command from the terminal The terminal will name each operation in sequence as shown below You need to wave administrator card at the induction area to confirm the relevant command 1 To download transaction logs from terminal to USB flash disk Green LED blinks gt sf Download transaction logs Please wave your adminis trator card for confirmation gt Wave administrator card at the card induction area to confirm gt 6 The operation is successful 2 To download users from terminal into USB flash disk Green LED blinks gt 6 Download users Please wave your administrator card for confirmation gt Wave administrator card at the card induction area to confirm gt The operation is successful 3 To upload users from USB flash disk into terminal Green LED blinks gt s Upload users Please wave your administrator card for confirmation Wave administrator card at the card induction area to confirm gt s The operation is successful 4 To upload firmware from USB flash disk into terminal Green LED blinks gt s Upload firmware Please wave your administrator card for confirmation gt Wave administrator card at the card induction area to confirm gt The operation is successful CONTENTS 17 18 4 e MANAGING USER Administrator and Administrator Card Enrollment of an Administrator Card is required
22. t Release tamper switch gt This might trigger a connected alarm gt Wait 30 sec gt press and release the tamper switch 3 times gt The terminal will emit 3 beep sounds gt the terminal will then reset to its default factory settings Remarks All contents of the terminal will be deleted including the administrator card user informa tion and transaction logs All settings will return to the default settings The IP address will return to 192 168 1 1 and terminal ID will return to 1 after the process CONTENTS 7 3 CONNECTION SYNCING TERMINALS Installations FingerTec terminals offer several connections for power and communications In stallations of FingerTec time attendance terminals are simple than installation for door access functions Mount On Wall 4 feet 1 2 meter recommended Attach the back plate on the wall securely and attach the terminal to the back plate when mounting it on the wall 8 CONTENTS Communications Connection points for power and communication are available on top of the termi nals Refer to the following diagrams for the terminals you require POWER SUPPLYPORT WIEGAND INPUT CONNECTION PORT RS485 CONNECTION PORT 1 RS485 Single Connection RS485 Data Converter 3rd party Va controller with AB 26 bits wiegand output fr RS485 Data WIEGAND OUTPUT CONNECTION PORT 3rd party controller with 26 bits wiegand intput For
23. tput Cable k Ce Power Supply Cable A Packet of Bolts RFID Card 5 pieces MIFARE Card 1 pieces for H2i RFID for H2i MIFARE Back Plate Thick Rubber Padding Keypad gt CONTENTS 3 4 Included Printed Materials FingerTec Comprehensive DVD e Quick Start Guide Pamphlet User Enrollment Template Form Warranty Card Activating H2i Connect all the cables correctly at their specific points and turn on the power sup ply The H2i terminal does not have an on off button Registering H2i Make sure that you register your H2i s warranty with us at www fingertec com ver2 english e_main html gt CONTENTS 2 BASICS Introduction to H2i FingerTec H2i is a simple master terminal functioning as a time attendance and door access device and it can be used as a time attendance recorder as well The H2i has a simple and sleek design as it comes without a keypad or any form of a display screen It communicates with its users mainly through its voice commands as well as its dual color LED light To perform administrative functions on the terminal an administrator card is needed However the H2i also has the option of using a nu meric USB keypad as an administrative tool As usual more advanced management of FingerTec H2i can be done via the included software in the package H2i Overview LED USB Port amp Speaker Reset button Fingerprint Scanner Card Induction Area
Download Pdf Manuals
Related Search