1580R User`s Manual
Contents
1. the centrifuge decelerates immediately 2 TAY ROZEN 5 8 Start Stop Action 5 8 1 Start 1 After setting RPM RCF Time and Temp touch Start button gt During running Start LED is turned on gt The instrument is running only the door is closed 5 8 2 Stop 1 In case of touching the Stop button the operation is stopped running 5 9 Emergency Door Open For emergency door opening you can use the Emergency Door Open Tool when the instrument is completely stopped The daar can be unlocked manually with the Emergency Door Open Tool through the emergency door opening hole 1 Find the emergency door open hole in the front body of the instrument and take out the white rubber closure 2 Insert the Emergency Door Open Tool into the hole and revolve it counter clockwise until the door is released Manual opening should be performed only when spinning is completely stopped Otherwise harmful damage will be accompanied to nat only operators but samples After opening the door manually is recommended to wait until normal electricity comes back OY ROZEN 6 Maintenance 6 1 Outer part of Instrument 1 Clean the outside of the instrument with dry soft cloth If necessary dip the cloth in neutral detergent and clean contaminated area Keep completely dry after cleaning 2 Do not use any volatile chemicals such as alcohol and benzene ete 3 Be c2. operational safety this instrument has the automatic rotor recognition function 4 When you supply the power Searching Rotor to Rotor will be appeared If the rotor is absent the Error 9 will be appeared 4 3 Positioning of Sample Tubes Action 1 Before loading sample tubes check the water drop or dirt in the rotor hole or inner adaptor gt there a water drop or dirt in the rotor hole or inner adaptor remove it with soft dry doth 2 Tubes should be placed in the rotor with same amount of samples at symmetrical positions gt Only use appropriate centrifugal tubes and do not exceed the speed beyond the tube s g force gt For safety fll the sample for 70 80 in the tubes Correct Way of Sample Balancing and Tube Usage IU rum QOO 000 M the number of samples is not in pair please load the control tubes at each symmetrical position Otherwise it results noise and vibration which eventually damage the instrument For safety the Imbalance Cut Off function wil be occurred there is imbalance of loading tubes Error Imbalance error Please refer to 7 Trouble Shooting TAY ROZEN aou rsh spat isum 5 Operation 5 1 Key Functions of Control Panel ime For automatic conversion of RPM RCF and to set the speed Use to set time available range up to 9 hour 59 min 0000 continuous D T
3. 2006 he tawe tember its tin equipe designes for lem conan relier aci ui cool refer Sun Km Presiane EY RIZEEN
4. rotor clean the motor shaft and chamber with soft dry towel 4 2 1 Swing Out Rotor 2 Mount a proper rotor into the motor shaft 3 Gasp the ratar with one hand and Rotor Locking Tot at the center hole of the rotor gt Tassel the rotor Rotate the Rotor Locking Tol devi gt To disassemble the rotor Rotate the Rotor Locking Ta 4 Hang the appropriate buckets into the rotor gt Load the identical bucket at each wing for safety Do not leave a vacant wing without bucket wings should hold identical bucket gt Remove dirt and dust around hooks of rotor and hanging part x of bucket 8 Spin the rotor manually to check if bucket swinging is free enough and ever they do not swing freely apply the Lubricant grease to the linking area 4 2 2 Fixed Angle Rotor 2 Mount a proper rotor into the motor shaft Grasp the rotor with one hand and place the Rotor Locking Tool at the center hole of the rotor gt assemble the rotor Rotate the Rotor Locking Tool clockwise until tightly assembled gt To disassemble the rotor Rotate Rotor Locking Tool counterclockwise 3 To clase of the rotor lid rotate the rotor lid nut clockwise gt For opening lid rotate the rotor lid nut counterclockwise Wen you run a angle rotor make sure that the rotor id is tightiy closed I you dont close the rotor ld completely it wil be crushed 4
5. on the motor shaft properly check it with spinning manually Do not stop the rotor by touching with hand during the instrument is running Emergency door open should be performed only when spinning is completely stopped Should not exceed the rated speed or specific gravity Samples whose density is greater than 1 29 must have reduced maximum rotational speed to avoid rotor failure sample content should not exceed 80 of tatal capacity of tube Otherwise it would cause spillage of sample fluid and even the tube breakage ALWAYS load the tubes symmetrically with evenly weighted samples to avoid rotor imbalance If necessary use the water blank to counterbalance the unpaired sample The operation speed should not exceed the highest value of the individual guaranteed g forces of each the centrifuge rotor bucket or adaptors and sample container especialy the guaranteed g OY ROZEN 15 16 aL force of sample container should nat be neglected The rotors should be cleaned and kept dry after every use for longer and safety ALWAYS disconnect the power supply prior to maintenance care and service to avoid electrical shock ALWAYS use proven disinfection procedures after centrifuging biohazardous materials Should not centrifuge flammable toxic radioactive explosive or corrosive materials When it is necessary to use toxic or radioactive materials or pathogenic micro organisms which belong to t
6. the number buttons to change the hour value 3 Touch the Enter button to complete the setting then MIN then SEC at the top of the minute then second blinks automaticaly 4 Touch the number buttons to change the value S Touch the Enter button to complete the setting D3YFADIZESN I nens d Centrifuge 1580R 16 5 4 Setting Temperature and Fast Cool Action 5 4 1 Setting Temperature gt Temperature can be set from 20 to AUC Temp setting unit 1 1 Touch the TEMP button Default or latest temperature value blinks the display window 2 Touch the number buttons to change temperature 3 Touch the Enter button to complete setting 5 4 2 Fast Cool 1 Setting the temperature Please refer to 5 4 1 Setting Temperature 2 Touch the Fast Cool button for fast cooling gt fast Coo on LED is tumed gt The display shows a message as follows Searching Rotor gt gt recognition OK gt touching the Fast Cool button the instrument is refrigerated down to the set temperature in short time During the fast cooling the rotor runs at low speed 1 000 gt The passed time is showed on the display window 7 youd We to load your sample tubes before touching the Fast Coal bution please check the sample is safe during spinning at 1 000 rpm lt Before starting Fast Cooling please check the rotor coupl
7. Angle Rotor GRF 6 15 24 tas i am am Fixed Angle Rotor GRF 5 50 8 D banc Mi o isa Tas Fixed Angle Rotor GRF 6 250 6 52 m Meere mu be pj vm Pa a Fixed Angle Rotor GRF G m2 0 24 Fixed Angle Rotor GRF G m2 0 30 p pm asin enn ac Hy ro BU m wants E 9 Product Range cce Gg ost EJ TAY FROIZEEN coge in Doc No STCADE ME Declaration of Conformity We Gyrozen Co Ltd Station 544 1 Bangmyeang dong Yussong gu Dasjeon 305 301 Korea decir unde cur ck Maf he per Description Centrifuge 1580R o which bs decir etes isn wih owing ory use Part Genera Safety for and use Far 2 Peicular rere equipment or mens EMG resurenerts scri ana SM Lins ar measurement Coun af 15 Docorer 2004 on the aporcemeten at ire awe no arbor Sos slaeweraanstcorpctbty ona repealing Drecie toc 0608EC of te European Palamertand or Counet of 12
8. Multi Purpose High Speed Centrifuge 1580R User s Manual Station 30 12 Gyeryang ro 141 91 fusecung qu Daejeon 3 DOC No 040 00204 11 CY FADIZETP Designed to suit your exact needs Wide range of modern centrifuges a wide variety of laboratory applications THE BEST FUNCTIONAL QUALITY SAFETY and ROBUSTNESS nsn etree EY FAELZENI sim CONVENIENCE IN OPERATION ith very futon ore Cdp wit bright an ue cp m colimus uta ML veros dein lu asp local though he pwnd A Prayam memory tarup opens Mars l n chon edge bets and sapor EASY CUSTOMIZATION AS nts atro e aantig to sme sein Rey fect sy ora concor pryam et ECO FRIENDLY MANUFACTURING ase Cinco uar ethan at TAY RREIZEEN oh seed centage 14 12 21 22 42 sa s2 55 52 CONTENTS Page Meanings of Symbols amp Safety Precautions aa Meanings of Symbols 6 Safety Precautions ss 7 Product Description amp Technical Specification Product Description Technical Specification Unpacking Installation Power On Off and Door Release Rotor Coupling and Disassembling Positioning of Sample
9. Tubes Operation Key Functions of Control Panel 5 Setting the RPM RCE Value 5 Setting the Time Value Setting Temperature and Fast Acceleration Deceleration Program Saving amp Recalling Pulse Start Stop Emergency Door Open Maintenance Outer part of Instrument Chamber Shaft Rotor 6 5 Transportation of Instrument 7 Trouble Shooting Check ist 722 Error Code 80 Rotors amp Accessories 9 Produet Range c OGY ROZEN igh speed coniuge 1 Meanings of Symbols amp Safety Precautions 1 1 Meanings of Symbols 141 Symbols on the device Symbol Meaning Symbol Meaning Attention and warning Attention and warning for electi shack Attention and warning far rotor coupling Attention and warning for door opening and closing Attention and warning for correct way of sample balancing in the rotor Attention and warning for correct way of buckets position The door should be AUTO DOORLOGK dosed by gentle press 48 down touching motion 1 1 2 Symbols in this document Symbol Meaning Symbol Meaning This symbol refers to safety relevant warnings and indicates possible dangerous outcome
10. areful not to make scratches on the surface of the instrument The scratches can cause corrosion on the surface of the instrument 22 Many rust appears clean it with neutral detergents and keep dry 6 2 Chamber 1 Keep dry inside the chamber after every use 2 Ifthe chamber is contaminated dip the cloth in neutral detergent and clean contaminated area 6 3 Shaft 1 make special attention to clean the motor shaft to avoid any imbalance problem due to the contaminants 2 After using the instrument take out the rotor from the shaft and clean the shaft with dry soft doth to keep dry 6 4 Rotor 1 Many parts are contaminated with samples clean the rotor with soft wet cloth and keep the rotor 2 careful not to make scratches inside or on the surface of rotors Any small scratches can cause corrosion of the rotor and big damage to the instrument 3 you do not use the instrument keep the rotor separately from the motor shaft and stand it upside down 6 5 Transportation of Instrument 1 Mf you need to move or ship the instrument be cautious to protect the motor shaft from any physical impact or turbulence 2 Do not mount a rotor in any cases of movement inside the chamber with proper materials to keep the motor shaft on place and not to be influenced by physical pressure TAY RREIZEEN 7 Trouble Shooting 7 1 Check List Symptom Check list Connect the AC Power cord an
11. d make sure that the line is completely Power failure connected between the instrument and power outlet Check the power switch is turned on Please refer to 4 1 Power On Off and Door Release If the door is not closed completely the instrument can t run Don t run Check the Door LED on the display window and dose the door completely Can t open the door If the power is out check the main fuse for the laboratory to supply the power If it is not solved in shortly open the door with emergency door tool manually for safety of sample Please refer ta 5 9 Emergency Door Open Can t close the door Remove the dirt at the door latch and then close the door completely again the door seems not being closed by mechanical reason please contact our service team Noise and vibration during running Please check the balanced status of both the table and the instrument Please re check the coupling status of the following three matches to minimize the noise 1 the balanced way of coupling of the rotor into the motor shaft 2 the completeness of fixing of the Rotor Locking Nut on the rotor 3 the matching status of Rotor Lid with the rotor Please refer to 4 2 Rotor Coupling and Disassembling Check balances of samples in the rotor Please refer to 4 3 Positioning of Sample Tubes and load the same weight of samples symmetrically TAY FADIZEEN 7 2 Error Code Jf the instrument sho
12. emp Use to set temperature 20 C 40 C D accore Use to set the acceleration amp deceleration level fram 1 to 9 steps deceleration step means natural deceleration Larger number means faster acceleration or deceleration n PROG Use to save a set of setting values or recall the saved program number Fast Cool Use to reach rapid refrigeration up to the setting temperature D Pulse Use for quick runs Enter Use for completion of data setting StaryStop Use to start and stop operation Door Use to open instrument lid OY ROZEN 5 2 Setting the RPM RCF Value Action 5 2 1 Setting the RPM Value gt Speed setting unit 10 rpm 1 Touch a RPM RCF button once 2 Touch the number buttons to change input value The minimum value of RPM is 500 3 Touch the Enter button to complete the setting IF not touching the Enter button the setting values are not saved but disappeared 5 2 2 Setting the RCF Value gt Speed setting unit 1 ref 1 Touch a RPM RCF button twice 2 Touch the number buttons to change input value 3 Touch the Enter button to complete the setting If not touching the Enter button the setting values are not saved but disappeared 5 3 Setting the Time Value Action 42 Time down counted after starting centrifugation 1 Touch the TIME button Display shows the maximum latest time value and at top of the hour value blinks 2 Touch
13. he Risk Group of WHO Laboratory Bio safety Manual should follow national regulations V Do mot place dangerous materials within 30 cm distance around the instrument and that is also recommended by 61010 2 020 42 se the emergency door open function only when the door button on the control panel is dumb under the condition af complete stop of rotor running V Never try to open or move the instrument if it is nat completely stopped V M the power input is more than 10 of the recommended voltage or fluctuates frequently it may cause malfunction of the instrument and often result serious damage Install the instrument at the place without any kind of corrosive gases TAY RIZEEN 2 Product Description amp Technical Specifications 2 1 Product Description Earth Leakage Breaker Switch Emergency Door Open Hole Power Switch Control Panel gt Ur SOOTY nm ech ROZEN 2 2 Technical Specifications Fed angle 15000 rpm 25910 xg REM RCE Swing out 5000 rpm 5394 xg Fired angle 6x 250 amp 15 ml capacity Swing out Ax 750 Temp range 20 40 Fast Cool button m Pulse timed lt 10 he Time control RPM RCF conversion Yes Noise level 48 E ec Dee 5 10 steps Program memory 100 Rotor Identificatio
14. ing and symmetry of sample tube 5 5 Acceleration Deceleration gt Use the adjustment function of acceleration amp deceleration levels ta protect sensitive samples Action 1 Touch ACC DEC button then at the display of ACH blinks 2 Input the desired level of ACC from 1 to 9 Level 9 The fastest acceleration TAY RIZE 7 3 the level by touching Enter button And then P at the display of DEC blinks 4 input the desired level of DEC from D to 9 Level O Natural deceleration Level 9 Fastest deceleration 8 Fix the DEC level by touching Enter button 5 6 Program Saving amp Recalling Action 5 6 1 Program Saving 1L Set parameters Refer to 5 2 5 5 e Touch the PROG button longer than 3 seconds to save your preferred set values 3 Check the message of PROGRAM SAVE 44 at the display and input omen desired number to 8 blinks vas 4 Touch the Enter button to complete the saving 5 6 2 Program Recalling 1 recall the saved program just touch the PROG button shortly less than 1 see 2 Check the message of PROGRAM CALL 4 and input the program number you want to recall Then touch the Enter button memes 1 gt Display window show the saved setting parameters RPM RCE ga TIME TEMP WE 5 7 Pulse Uti for quick and short spin down Action 1 you touch Ple button and release at the point you want to stop
15. n Automation Imbalance cutout Yes Display Siue LCD Safety ld lock 7 Lid drop protection Radius correction Yes Power supplyv z 220 50 60 110V optional Power requirement KVA Dimension W x D x H mm Weight without rotor Kg mark m Cat No This instrument has following functions for safety 1 Automatic rotor identification function 2 Automatic detection and alarms for imbalance excess speed and heating Automatic door lock fur BYREZEN 10 3 Unpacking the installation of the instrument 1 Open the box and lift out the instrument carefully 2 Two people should keep the system horizontally to lift it up on the flat table 3 To disassemble the Motor Protecting Devices use the additionally supplied wrench yard unscrew and remove all bots 1t is now ready for installation Place the instrument on the solid and flat table 4 Installation 4 1 Power On Off and Door Release Action 4 1 1 Power On Off 1 After connecting the AC Power cord at the power socket on the right back of the instrument turn on the Earth Leakage Breaker Switch 7 gt Check the proper power OY ROZEN oe rsh spas contigs isum 2 Turm on the instrument by pressing a switch on the let side of he instrument gt With beeping sound right before setting value is displayed gt The default values are r
16. nsor TF the temperature of compressor is over heated up this message s appeared No user action Please call Gyrozen Field Service Engineer Any wire disconnection or tuning of the instrument must be performed only by a service engineer who is authorized by GYROZEN Lid GYROZEN 4 2 8 Rotors amp Accessories Swing Rotor GR5 G 100 6 T ism vk im WE nes p OCYRAZEN Swing Rotor 5R5 6 r250 4 OGY ROZEN 7 Swing Rotor GRS G c250 4 tee T 77 7 am Swing Rotor GRS 6 750 4 verre j Rue pus Swing Rotor GRS G r750 4 oan TE amp ee E Fixed Angle Rotor GRF 6 85 6 p s 3 pe Er w n w 7 3 w D Angle Rotor GRA 5 15 24 a gt 11 71 e deii tam n te EE ss NT ere ae 2 pen p mx im um Fixed
17. ovide proper power T the instrument is spun with over speed there wil be some problems in the overload of motor and the output of motor Shut off the power supply and then turn on the power switch again to check the instrument TI the installed software has bugs this message is appeared Eror Software Tuning the firmware Download Eror 8 Imbalance Check weight balances of samples Please refer to 4 3 Positioning OYRAZEN 2m Sample Tubes and then tum off and on the instrument for checking Eror 9 Rotor ID or RPM Sensor 7I the function of rotor recognition is failed this message is appeared This message will be cleared by coupling an appropriate rotor Please referto 4 2 Rotor coupling and disassembling the error code shows continuously please call Gyrozen Field Service Engineer Chamber Temp Error TF the instrament i reached to setting temperature within an hour this message is appeared user action Please Gyrazen Field Service Engineer Error 12 Temp Sensor Errar TF there a faulty the temperature sensing of chamber or over heated this message is appeared user action Please Gyrozen Field Service Engineer Error 15 Mator Temp Sensor TF the motor temperature sensor cant recognize this message is appeared No user action Please Gyrazen Field Service Engineer Error 16 Comp Temp Se
18. pm 10 min ACC 4 DEC 4 and 25 4 1 2 Door Release 1 Far opening the door touch the DOOR button gt Should touch the DOOR button When the door is dosed Door LED shows off gt Close the door unti hearing cani shut gt When the door is opened the door LED turns an V The door is not opened while the instrument is running the door is opened the instrument could not be operated even with pressing the Start button For operational safety this instrument has the automatic rotor recognition function When you supply the power Searching Rator Change to Rotar 07 will be appeared If the rotor is absent the Error 9 wil be appeared This message will be cleared after rator coupling and running The door is not automatically opened after finishing operation to keep the sample at proper temperature Power Failure there i any power failure during operation door is not opened with Door button Door can be opened only when the operation is completely stopped and the power is on again If you want to open the door at the power failure please refer to 5 9 Emergency Door Open 4 1 3 Door Lock The door is closed automatically only by gentle press down motion soan as the doar latch touches the sensor inside iis automaticaly dosed by a geared motor of door lacking system TAY RREAZEEN 7 4 2 Rotor Coupling and Disassembling Action 1 Before coupling
19. s Note This symbol refers to the important reminder EY FAELZENI Multi Purpose High Speed Centrifuge 1580R 1 2 Safety Precautions Before using the instrument please read this operation manual to ensure correct usage Incorrect handling the instrument could possibly result in personal injury or physical damage on the instrument or its E in ES ALWAYS locate the instrument on a flat rigid and stable table capable of withstanding the weight of the instrument and ils spinning operation ALWAYS make a safety zone of 30 cm around the centrifuge to indicate that neither hazardous materials nor persons should be permitted within the area during operation 22 ALWAYS position the instrument with enough space on each side of instrument to ensure proper air circulation ALWAYS install the instrument within a temperature and humidity controlled environment Permissible ambient temperature 5 35 Relative humidity lt 85 Before connecting the power check the rated voltage Should not use unapproved rotors and accessories 4 Oniy use rotors from Gyrozen Co Ltd with appropriate centrifugal tubes and suitable adaptors to embrace sample containers tightly enough inside rotors Before operating the instrument check if the rotor and the rotor lid are securely fastened Should operate the instrument with a rotor properly installed and secured to the motor shaft Mount the rotor
20. ws the error code with beeping sound press STOP button to stop the beeping sound and press Ente button to release of the error status and make the instrument go to the default setting again Error Possible Causes Actions Shut off the power supply and then on the power switch again to check the instrument I the error code shows continuously although you try to operate again please contact us If the door is not closed completely this message i appeared Remove the dirt at the door latch and then close the door completely again Check the Door LED on the display window I it is mot solved in shortly open the door with emergency door tool manually for safety of sample Please refer to 5 9 Emergency Door Open Ifthe motor is overheated this message is appeared Shut off the power supply for an hour and then turn on the power Eier Met Unibet switch for checking the instrument If the error code shows continuously please contact us TF the power input of Power supply V Hz is 10 less than required power this message is appeared Low Voltage Shut off the power supply and then check the voltage of the Power supply V H2 Use AVR to provide proper power 17 the power Input of Power supply is 10 more than required power this message is appeared tors High Voltage Shut eff the power supply and then check the voltage of the Power supply V H2 Use AVR to pr
Download Pdf Manuals
Related Search