BlueKeeper 1009.pub
Contents
1. Connect a dynamic microphone cable to the Send 1 jack on the BlueKeeper Be sure to set the Mic Line button to the Mic position e Output Connect a stereo cable from the mini jack Stereo Out on the BlueKeeper to the Line In on your computer sound card or other recording equipment that has a stereo input or connect a mono cable from the mini jack Mono Out on the BlueKeeper to the Mic In on your laptop computer or other recording equip ment e Power Connect the supplied DC power supply to the back of the BlueKeeper and then to an AC power outlet e Your BlueKeeper is now ready to take calls You can establish a connection to your Bluetooth enabled cellular phone see pages 16 17 and place or receive a call e Set the Send level control so that while you are speaking into the mic the Send LEDs on the BlueKeeper light the 20 dB green LED consistently and flash the 9 dB green LED with only occa sional flashes on the 3 dB red LED Set the Caller control for good recording level of the caller audio at the output jack Connect Stereo Out Computer to PC Line In or to Stereo Line Input on mini recorder a Line Line Mic in out in 6 X BlueKeeper 3 Bluetooth BlueKeeper Wireless Audio Gateway JK Audio i Headphones Call a Drop Sane Send 1 Sond 2 Caller i sa E Pair Caller w Figure 3 Basic Connections Send Signal Level The Send LEDs display th2. 3 4 5 6 7 8 9 BlueKpeper wirelpss Audio Batewa JK Audio Call r Drdp seda Serd 1 Seni2 Caller Hbadphonds WF 20 4 3 eoo Pair Callbr a 10 11 Figure 1 Front View Call Button Press this button to initiate Bluetooth Idle or Pair ing mode redial an outgoing call or accept an incoming call Drop Button Press this button to drop hang up a call Send 1 Level Adjusts the signal level that you are sending out to the cell phone through the female XLR input Send 2 Level Adjusts the signal level that you are sending out to the cell phone through the 3 5mm mini jack input Caller Level Adjusts the level of the incoming audio as it is going out the output jacks Headphone Level Adjusts the signal level coming from the 3 5mm front panel headphone jack Headphones The 3 5mm stereo headphone jack contains a mix of both the Send input audio and the Caller audio Blue LED Indicates Bluetooth status lit steady when you are on line with a call or flashes to show pairing status Send LEDs Displays the signal level going to the phone call Power LED Lit when unit is plugged in and receiving power Caller LEDs Displays the signal level coming in from the phone call after the DSP This signal level will not change when you adjust the Caller knob Features Rear View 12 13 14 15 16 17 18 19 12 13 14 15 16 17 18 19 Send 1 Caller Figure 2 Rea
3. Inc is under license Other trademarks and trade names are those of their respective owners Warnings and Safety Precautions 1 2 3 4 Read and keep these instructions Follow all instructions and heed all warnings Clean only with a soft dry cloth Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the three prong grounding type plug If the provided plug does not fit into your outlet con sult an electrician for replacement of the obsolete outlet Do not use this unit if the electrical power cord is frayed or bro ken The power cord should be routed so that it is not likely to be walked on or pinched by items placed on or against it To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Refer all servicing to qualified service personnel Table of Contents Iuicerelteie e vicii gga ANG wdc amp a oo tebe bw nia Ss 2 Warnings and Safety Precautions 3 Features IONE VICW usd ace P EEIGIE EPA EMERGERE ds 6 Rear VIEW sues V Hole ERENX Kuce v KORR EE Rd x 7 Connection Basic COnneclionS sies mado ke E Ee ccs Ga 8 Operation Send Signal Level 0 000 e eee 9 Caller Signal Level 0 00 00 c eee 9 Setup diagrams Studio Mix Minus Setup 0005 10 11 Why Do Need a Mix Minus S
4. laptop only record half of the conversation Pm using the Stereo output on the BlueKeeper and have a stereo cable Most laptop computers only have a mic input which is mono You will need to use the mono mic level output of the BlueKeeper or get a sound card with a stereo line level input for your laptop or you can use a USB or Firewire interface product that will ac cept a stereo input Also many laptops and mini recorders have a built in micro phone You may need to change the settings on your laptop or recorder to be sure you are recording from the input jack and not the integrated mic There is a loud hum on the output of my BlueKeeper even with nothing else connected What else could it be Make certain you are using the regulated power supply that was shipped with this unit Power supplies are not all the same 19 Specifications Inputs Send 1 Send 2 Outputs Caller Stereo Out Mono Out Headphone Bluetooth Standard Distance Frequency response Headset mode Headphone mode Power Size Weight Balanced Female XLR 1k ohms 15 mV RMS 34 dBm nominal Mic Line pad switch Line 6 dBu max Unbalanced 1 8 3 5 mm mono 20k ohms 250 mV RMS 10 dBu nominal Balanced Male XLR 200 ohms 500 mV RMS 4 dBu nom 14 dBu max Unbalanced 1 8 3 5 mm stereo 50 ohms 250 mV RMS 6 dBu max Left Send Right Caller Unbalanced 1 8 3 5 mm mono 50 ohms 15 mV
5. you have the Caller audio connected to until the Peak light for that channel comes on then reduce the level slightly just until the light goes out 11 Mix Minus Setup for Mixer Why do need a Mix Minus Setup Mix minus is an audio signal that is designed to avoid feedback and echo in a conference or telephone interface application When con necting an audio interface to a mixing console the caller s audio will be connected to an input channel on the mixer along with all the mi crophones music etc All of these inputs combine to create the Master mix to be sent to your broadcast recording device or the speakers of your PA system However if you connect this Master mix to the input of the BlueKeeper you are also sending the callers own audio back to the caller This completes a feedback loop and creates a strange and annoying echo That is why it is important to create a special mix that contains a mix of all the microphones music etc Minus the caller s audio Wireless Phone Interface Mix Minus Caller PA System OG OOC Mix Plus Caller prosdeast Audio Mixer Podcast etc Which Mix Minus Setup Should Use Most radio stations and recording studios should use the Studio Setup shown on pages 10 11 Using an Aux Send output that is Post Fader will keep the audio that is being sent out to the caller tied to the same output you send to your broadcast or PA system This way your sound engineer can more easily control e
6. 23 BlueKeeper is covered by a 2 year warranty to be free from defective workmanship and materials In the event that the BlueKeeper needs repair you must call us to get an authorization and then carefully pack and ship it to us You will pay for shipping to us and we will pay for return back to you UPS ground No free repairs will be made if the defect was caused by misuse weather conditions or other cause except for defective workmanship or materials THERE ARE NO EXPRESSED OR IMPLIED WARRANTIES WHICH EXTEND BEYOND THE WARRANTY HERE MADE 10 09 JK Audio Inc 1311 E 6th Street Sandwich IL 60548 USA Voice 815 786 2929 Toll Free 800 JK Audio Fax 815 786 8502 info jkaudio com www jkaudio com Copyright 2009 JK Audio All rights reserved
7. BlueKeeper Wireless Audio Gateway User Guide JK Audio Te goo W o2 8 0 0 JK Audio combines Bluetooth Wireless Technology with profes sional audio electronics in a convenient desktop design BlueKeeper pairs to your cell phone like a Bluetooth wireless headset Connect your favorite microphone and headphones for dramatically improved sound quality at both ends of the call BlueKeeper also pairs to Bluetooth equipped sound cards and music players in full bandwidth stereo A2DP mode What is an Audio Gateway BlueKeeper allows you to send mic and line level signals into your wireless phone while maintaining excellent separation between your voice and the caller The stereo output jack provides your voice on one channel and only the caller s voice on the other chan nel The balanced XLR output jack contains only the caller s voice The 3 5 mm stereo line input jack allows recordings to be sent into the Bluetooth device The 3 5 mm stereo line output jack provides your full bandwidth send mix on the left channel and Bluetooth caller audio on the right channel The headphone output gives you a mix of the XLR input 3 5 mm input and Bluetooth audio Any Questions Before you pick up the phone Please thumb through the rest of this manual You might find those deep technical questions are covered on later pages The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by JK Audio
8. RMS 34 dBu nom Mixed Send and Caller 1 8 3 5 mm stereo 8 ohms 1 2 W per channel Mixed Send and Receive Bluetooth 2 0 15 feet 5 meters phone 300 Hz 3 4 kHz A2DP 30 Hz 20 kHz Universal AC supply 120 240 VAC 50 60 Hz 25 watts max 7 x 6 x 1 6 18 x 15 x 4 2 cm 2 2 Pounds 1 kg 20 A oS E Q x Q Q en euoudpeeH a JED e mdno gul 0813S WW GE INdING awal MA ouo e uuu qe 8 8 auoudpeaH EA EIEE Jalen el el uoojenig a a pues Mj eur IIN indu aur LULU GE Indu a IX Figure 9 Block Diagram 21 22 FCC Part 15 Compliance This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by JK Audio can void the user s authority to operate the equipment
9. ach channel During a station break the talent microphones can be muted simply by turning off the output level knob or slider and their audio will not be sent to the broadcast or to the caller If you have a small studio and you use your wireless phone interface to record interviews you might consider using the Simple Setup on page 13 When the Aux Send output is Pre Fader the levels you set on the Aux Send controls will only affect what the Caller hears and the levels you set at the output faders will only affect the recording or broadcast If the talent wants to be able to talk to the caller during station breaks this is the setup you should use although the talent would need to con nect their headphones to the BlueKeeper instead of to the mixer You should also use this setup if you want to be able to send music or sound effects to the broadcast that the caller will not hear 12 Simple Setup for Mixer he BlueKeeper E Bluetooth Caller to any line Aux Send A pre fader on mixer level input on mixer to Send 1 on BlueKeeper Mic Line button out Line Number of mics depends on mixer San Use Main Outputs USB or Firewire connectors to send audio to recording device 616 For whichever input channel you have the Caller connected to turn the corresponding Aux A control to minimum usually hard left All other Aux A controls should be set for what you wa
10. airing Mode 2 sec off 2 sec on 2 sec off 200 ms on 100 ms off 100 ms on Hold Bluetooth Call Pair button in at least BlueKe 3 sec to reach Pairing Mode the first time a new device is connected 1 sec thereafter to easily connect from Idle Mode Bluetooth LED pattern after Bonding Ld Lo Bonded 2 seconds off 1 second on Figure 8 Bluetooth LED Patterns 17 What is the range of the Bluetooth transmitter receiver BlueKeeper will transmit and receive audio signals up to 15 feet 5 meters from your Bluetooth device Can send and receive audio at the same time Yes you can You can have full duplex conversations with your microphone sent to the Left channel of the stereo line output and the Bluetooth audio sent to the Right channel If have an audio source connected to the Send 2 input will that audio also be present at the Output mini jacks Yes the stereo input will be added to your microphone or line level audio from the XLR Send 1 input and both will be sent to the Mono Out and to the Left channel of the Stereo Out This combined input will also be sent to the Bluetooth connection Can pair my BlueKeeper to two cell phones and send my audio to two locations simultaneously No your BlueKeeper can only be paired to one Bluetooth en abled device at a time 2 Will the audio gateway provide phantom power for a con denser mic No this device will not provide phantom power If yo
11. d XLR male to 1 4 cable not included connect the Post Fader Aux bus output Send B on this mixer diagram to the Send 1 XLR input on the BlueKeeper Make certain the Mic Line button on the BlueKeeper is Out Line On your mixer locate the row of Aux B knobs This row of knobs will set the level of each input channel to the Aux B output which is sent to the phone caller Turn all of these knobs to 9 o clock except for the channel you have the Caller from the BlueKeeper connected to Channel 4 in this example This Aux B knob should be set fully off hard left on most mixers opeak into your microphone and watch the level indicators on the mixer Adjust your Mic Level so your audio is at 0 dB on the meter most of the time and occasionally up to 3 dB Repeat for each mic Next check the Send level meter on the front of the BlueKeeper Adjust the Send 1 knob on the BlueKeeper so that both green lights are on while you speak and you only occasionally see the red light Some mixers may have an Aux Send master control that will affect the audio level you send to the BlueKeeper You should start with this knob at 12 o clock and agjust it if necessary to get the correct level on the BlueKeeper Following the instructions on pages 16 17 of this guide pair your cell phone to the BlueKeeper and set up a call on your phone Press the Call button on the front of the BlueKeeper As the Caller speaks adjust the Gain knob on the mixer for the channel
12. e signal level as it goes out to the phone caller and can be used as a general guide during setup The goal is to drive the Send audio at high enough levels to avoid phone line noise but not so loud as to cause excessive clipping and distortion Adjust the Send level control so that you occasionally see flashes of the red 3dB peak Send LED Then place a test call to someone Readjust the Send level so that your audio is at a comfortable lis tening level without distortion The Send 1 volume control will set the level of any audio connected to the Send 1 XLR jack on the back of the BlueKeeper The Send 2 control will set the level of the Send 2 mini jack on the back of the BlueKeeper These two inputs will be combined on the LED meter and on the Left channel of the stereo output mini jack Caller Signal Level The Receive LEDs display the strength of the audio signal coming from the Bluetooth enabled cell phone just after the DSP The Caller level control knob on the BlueKeeper does not change what you see on these LEDs You can adjust the volume controls on your cell phone to set the incoming Caller level on the LED meter Then adjust the Caller knob on the BlueKeeper to give you the best signal level at the Caller XLR output or the Right channel of the stereo out put mini jack You can listen to the combined audio level in your headphones Af ter setting the Send levels for the highest level you can send without distortion as indicated by
13. etup 12 Which Mix Minus Setup Should Use 12 Simple Setup for Mixer 00 0200 0 00 13 Mono Output to Recorder 00005 14 Stereo Output Interface L 14 Bluetooth Wireless Technology Bluetooth Proflles 2 rg ES REA EG ERIS SERA 15 Connecting to a Bluetooth Device 16 17 g2 qup rrr 18 19 SPECIICALIONS 4 4 4 4 3 420 444 eed vire EP Redde A 20 BIOCK Diagram s 53 d pea tecto a E bu Oir Gode Rec deos 21 FCG Gompliall 6B sod dtc goa edt iced cra con Cn eee 23 Waraniy erur preserie iea E d eq bute Ebo boy aeu Rd 24 Table of Diagrams Figure 1 BlueKeeper Front View 0005 6 Figure 2 BlueKeeper Rear View Lun 7 Figure 3 Basic Connections 0 0 0 0 llle 8 Figure 4 Studio Mix Minus Setup lille 10 Figure 5 Simple Setup for Mixer 000005 13 Figure 6 Mono Output to Recorder 14 Figure 7 Stereo Output Interface sun 14 Figure 8 Bluetooth LED Patterns 17 Figure 9 Block Diagram 2 0 0 0 cee eee 21 This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock 5 Features Front View 10 11 1 2
14. he Call Pair but ton on your BlueKeeper for a full 3 seconds and release The blue LED will flash rapidly about every 100 ms as BlueKeeper enters Pairing Mode Now go to your Bluetooth device and search for Bluetooth connec tions If this is the first time you have paired with this device select the option to add an audio device When the cell phone has found the new device select from the list the device ID of JKBKxxxx where the xxxx corresponds to the last 4 digits of the unit s serial number Enter Yes when asked to Bond with this device Enter the pin number as 0000 The BlueKeeper can maintain up to 16 devices in its connection history to make reconnecting to a previously used device simpler and quicker by entering Idle Mode Tech Note There is a difference between Pairing Mode and Idle Mode The very first time you connect to a new device you must be in Pairing Mode When you press the Call Pair button for less than 1 second then release it the blue LED will come on steady for a moment then it will flash at a rate of 2 seconds off and 200 ms on This first stage is Idle Mode Holding the Call Pair button in for 3 to 10 seconds be fore release will activate pairing mode In pairing mode the LED flashes very rapidly about every 100 ms Once in pairing mode any Bluetooth enabled device within range can pair with BlueKeeper After pairing is com plete the connection to that device is secure Af
15. nt to send to the phone line Each Aux Send bus is completely separate from all other outputs so these Aux controls will not affect what is heard on the Main outputs or on any other Aux buses This Aux Send bus should be pre fader if possible SO you can use the Level controls faders to set each channel at the main recording output without changing the levels you send to the caller Figure 5 Simple Setup for Mixer 13 Connection Alternate Setup Diagrams ym i Mb ehh h gt comcs c n m H Set Mic Line To Mic input on button In for laptop or other recording device BlueKeeper Bluetooth EB C Caller ED Figure 6 Mono Output to Recorder If your microphone is connected to the Left channel input then Recorder or Audio Interface use the Left channel output to connect to Mic Line ROL a ta Moy Line the BlueKeeper so that E S 7 m Stereo Outputs w e Kee e only your mic audio goes back to the caller Set Mic Line button Out for Line x BlueKeeper Bluetooth Caller Figure 7 Stereo Output Interface Bluetooth Wireless Technology Bluetooth Profiles The Bluetooth interface will first attempt to connect in Hands Free mode to a cell phone allowing 3 4 kHz telecom bandwidth If this is not available it will attempt to connect in Wireless Headset mode to any product such as a laptop computer that allows a Bluetooth wireless audio connection The Wireless Headset m
16. ode offers 20 kHz audio bandwidth BlueKeeper supports A2DP Hands Free and Headset profiles with BlueCore 5 Multimedia technology In Headset mode you will be able to receive full bandwidth stereo audio from any cell phone that supports A2DP While all phones and portables are different typically if you connect in cell phone Hands Free mode you will have a mono full duplex connection If you connect to a music player you will be in stereo A2DP mode Phone conversations have a limited bandwidth of 300 3 4 kHz Consult your cell phone or portable device for more de tails There are many profiles that may be used for Bluetooth communi cation BlueKeeper is compatible with these three typically used in cell phones and headsets A2DP Advanced Audio Distribution Profile Headphone mode used for stereo music streaming 30 20 kHz stereo receive only headphone mode Headset Facilitates mono full duplex audio between two paired devices 300 3 4 kHz mono both directions Hands Free Similar to Headset profile but allows the receiving device more control over the call such as volume accept reject end a call 300 3 4 kHz mono both directions 15 Connecting to a Bluetooth Device When you power up the BlueKeeper the blue status LED is not lit as the unit waits for a command Establishing a Bluetooth connec tion varies with different cell phones On your phone find and select the option to set up a connection Press and hold t
17. r View Bluetooth antenna do not obstruct Caller Output Male balanced XLR output contains only the caller s voice at line level Send 1 Input Female balanced XLR input for signals going out to the cell phone Mic or line level input Mic Line switch Sets the front end sensitivity of the Send 1 XLR jack Set to Mic if you intend to connect a dynamic micro phone directly to the Send 1 jack Set to Line if you are con necting to the output of a mic pre amp or mixer Send 2 Stereo Input 3 5mm mono mini jack input for signals going into the cell phone Line level otereo Output 3 5 mm stereo mini jack line level output con tains both Send and Caller audio channels with levels deter mined by the Send 1 and Send 2 level controls and the Caller level control Left channel contains your local Send audio and right channel contains the Caller s audio from the cell phone Mono Output 3 5 mm mono mini jack output contains a mix of oend 1 Send 2 and Caller audio with levels controlled by each of the input control knobs on the front of the unit This output is at Mic level and is suitable for connecting to the Mic input on a computer or other recording device Power Jack For connection only to the supplied 9VDC regu lated power supply Connection Although each application may require a slightly different setup the following diagram shows a primary configuration For a direct connection to BlueKeeper e Send Audio
18. ter pairing to your cell phone BlueKeeper is ready to take calls To place an outgoing call dial the number on your cell phone and the call will be active on BlueKeeper To redial the last number just press the Call button on BlueKeeper To answer an incoming call press the Call button on BlueKeeper If you do not hear your cell phone ring you may need to check the Bluetooth headset settings on your phone The phone may send a beep to your headphone instead of ringing to indicate an incoming call When your call is completed press the Drop button on BlueKeeper 16 Connecting to a Bluetooth Device When bonding is complete the blue LED will flash at a rate of 1 sec on 2 sec off Once BlueKeeper has been added to your cell phone subsequent connections can be made more quickly from Idle mode When the unit is placed in Idle mode it will search its connection history and automatically connect to the last device that is available To disconnect your cell phone select the Drop function on your phone s Bluetooth menu power off your phone or the BlueKeeper or take the cell phone out of the 15 range If left unused in Idle Mode for 5 minutes BlueKeeper will automatically disconnect To clear the connection history and return to factory reset hold the Drop button in for at least 12 seconds After resetting the BlueKeeper will return to pairing mode Bluetooth LED pattern to initiate Bonding L1 UUUL Initialize Idle Mode P
19. the LED meter listen to the audio in your headphones and set the Caller level to match the Send level Or if your recording device has a meter you can use that to match the Caller level to the Send level be connected to an adequate surge protection device for h WARNING t is strongly recommended that this product the power line at all times 9 Studio Mix Minus Setup NG BlueKeeper C3 Bluetooth Caller to line level Aux Send B post fader on input on mixer mixer to Send 1 on BlueKeeper Mic Line button out Line Number of mics depends on mixer Use Main Outputs USB or Firewire connectors to send audio to recording device or broadcasting equipment inputs oi aa SOO R0006 eoeececce oj b i ml Ven Pee jr ch 2i fj diris H Figure 4 Studio Mix Minus Setup 10 Studio Mix Minus Setup Following the instructions in the owners manual for your audio mixer connect your microphones headphones and recording de vice and set the levels on your mixer On the front of the BlueKeeper set the Send 1 and Caller knobs to 12 o clock Send 2 and Headphones are not used in this configura tion so they can be turned off To connect the BlueKeeper to your mixer use a balanced female XLR cable with an adapter if necessary not included to connect the Caller jack on the back of the BlueKeeper to any unused Line input on the mixer Using a balance
20. u connect a microphone directly to the BlueKeeper you should use a dy namic mic 2 How do I record onto my computer and edit the files You need to purchase or download any audio editing software of your choice You may also need to edit the audio configuration files on your computer or in your software to allow recording in stereo BlueKeeper just enables you to access audio from your Bluetooth cell phone 18 D How can send more audio to the caller without lighting the red 3 dB LED Cell phones have different audio levels so the Send control knob and the Send LEDs will respond differently Use the Send LED meter as a general guide then you may need to readjust for a comfortable listening level without distortion See page 9 What is the difference between Mic level and Line level Mic level is typically 20 30 dB lower than Line level and needs a pre amp to bring it up to Line level While many audio recording or playing devices will have an 1 8 input it is important for you to know what type of input it is Usually a mic input will be mono and will use a pre amp circuit and a line input will be stereo Check your cable also to be sure it is compatible with the type of input output you are using A stereo mini cable will have two black rings and a mono cable will have one black ring on the plug On many mixing consoles the XLR input will be mic level and the 1 4 TRS inputs will be line level Why does my
Download Pdf Manuals
Related Search