300Mbps N_Max Wireless Starter Kit WSK-3000
Contents
1. LevelOne User Manual WUA 0601 N Max Wireless USB Adapter V1 0 0 0804 Safety FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or peripheral devices FCC Radiation Ex2. You will see the WPS screen when you try to connect the wireless network with the WPS function Wi Fi Protected Setup WPS Configuration Join a Wireless Network Network Name SSID Automatic Selection Push the Button my access point Enter a PIN into my access point Enter the PIN from my access point Enterthe PIN 10904732 into your access point and click Start Button to continue Figure WPS Function Screen 17 N Max Wireless USB Adapter Data WPS Function Screen Network Name SSID Select the desired wireless network from the drop down list Push the Button on Select this and click Start button Then push the WPS my access point button of the Access Point Enter a PIN into my Select this to use the PIN method It will automatically gen access point erate the new pin code displayed in the field Click Start button and copy the value and paste in the Wi Fi Protected Setup screen of the Access Point Enter the PIN from my Select this to use the PIN method Entering the PIN from access point your access point in the Wi Fi Protected Setup screen of the Access Point and click Start button to continue You will see the following screen if WPS configuration is success Wi Fi Protected Setup WPS Configuration Success lll Join a Wireless Network Network Name SSID Automatic Selection Push the Button my access point Enter a PIN into my access point Enter the PIN
3. must be entered on each Wireless station The encryption key is derived from the PSK and changes frequently WPA2 PSK This is a later version of WPA WPA PSk The major change is the use of AES Advanced Encryption System for protect ing data AES is very secure considered to be unbreakable The PSK Pre shared Key must be entered on each Wireless station 24
4. M MI MM IM UE 9 System Tray ICOM ciao Dea Enc a Eua Dea eset abu mue roue cu CEU B S UE 9 CONNEC ssaa a a 10 SITE SUrVEY SOTET TT TD aa a aaia i aaa 10 Profile Manager SCreen iiiiecesscescctecsscecvevecevensscsceeveseved ctectassdeevacsdenecetecssriniedenerttaeees 13 Network 5 et eiosiei ue eei a rko eis un ccs issue De Quo dd ue 19 ADOULSCEOGI eic inet iui a lick o desavua uo disa E b 21 APPENDIX A SPECIFICATIONS 22 B IN GLDrIlM p 22 APPENDIX B ABOUT WIRELESS LANG eeeeeeeeeeee erre e eene n enhn nana nnns 23 mme E 23 BSS ES dicuntur Ub EDU ER pd 23 Channels IAE om EID Oe 24 WEP muore a 24 Wireless LAN Configuration 24 Introduction Chapter 1 Introduction This Chapter provides an overview of the USB Wireless Adapter s fea tures and capabilities Congratulations on the purchase of your USB Wireless Adapter The USB Wireless Adapter provides a wireless network interface for your Notebook or Desktop Computer Package Contents The following items should be included WUA 0601 N Wireless USB Adapter e Quick Installation Guide CD Manual Driver Utility e Extension Cable If any of the above items are damaged or missing please contact your dealer i
5. a Basic Service Set 55 Using the same SSID is essential Devices with different SSIDs are unable to com municate with each other ESS A group of Wireless Stations and multiple Access Points all using the same ID ESSID form an Extended Service Set ESS Different Access Points within an ESS can use different Channels In fact to reduce interference it is recommended that adjacent Access Points SHOULD use different channels As Wireless Stations are physically moved through the area covered by an ESS they will automatically change to the Access Point which has the least interference or best performance This capability is called Roaming Access Points do not have or require Roaming capabilities 23 N Max Wireless USB Adapter The Wireless Channel sets the radio frequency used for communication e Access Points use a fixed Channel You can select the Channel used This allows you to choose a Channel which provides the least interference and best perfor mance In the USA and Canada 11 channels are available If using multiple Access Points it is better if adjacent Access Points use different Channels to re duce interference e n Infrastructure mode Wireless Stations normally scan all Channels looking for an Access Point If more than one Access Point can be used the one with the strongest signal is used This can only happen within an ESS e f using Ad hoc mode no Access Point all Wireless stations sh
6. signal strength The USB Wireless Adapter is unplugged No connection to the USB Wireless Adapter 14 You can double click this icon to configure the Wireless interface See the follow ing chapter for details Chapter 3 Using the Windows Utility This Chapter provides Setup details for the AP mode of the Wireless Adapter Overview If using Windows you can use the supplied utility to configure the Wireless interface To Use the supplied Windows utility for Configuration e Right click the System Tray icon e From the pop up menu select Restore This Chapter assumes you are using the supplied WUA 0601 Wireless LAN utility System Tray Icon If the Wireless LAN Utility is running you can double click the icon in the System Tray to open the application If the program is not running you can start it using the option in the Start menu created by the installation For the USB Adapter this will be Start Programs LevelOne WUA 0601 WUA 0601 Wireless LAN Utility Status Information The menu options available from the System Tray icon are e Restore This will display the main screen e Radio Off The wireless adapter is not associated with the network when the radio is off WZC On Wireless Zero Configuration WZC is a service of Microsoft Windows which dynamically selects a wireless network to connect e Exit Terminate the connection to the Wireless Adapter 3 amp 5 uw Res
7. width Auto Guard Interval Auto Extension Channel Antenna Selection Auto Figure Advanced Settings Screen Data Advanced Settings Screen Do not change Enable this check box if you don t want to modify the settings settings in this screen Preamble 2 4GHz Normally this should be left at Auto The option Short Long preamble and header is intended for special application and equipment Transmit Rate Use this to manually set the speed if desired The default is Auto 16 N Max Wireless USB Adapter Fragment Thre The default value is 2346 In some cases you may be able to shold improve performance by adjusting this value RTS CTS Thre The default value is 2346 In some cases you may be able to shold improve performance by adjusting this value 802 11n Enable 802 11n 802 11n wireless network connectivity Network Channel Width The value is set as Auto Guard Interval This value is set as Auto Extension Chan Auto selects the wireless channel The value is set to Auto It nel will auto select the most suitable channel Antenna Selection The default value is set to Auto WPS Function Screen The Wi Fi Protected Setup WPS is to simplify the security setup and management of Wi Fi networks WPS Wi Fi Protected Setup allows consumers to protect their home networks by using the push button configuration on the router or entering an 8 digit PIN code if there s no button
8. 8 Press the USB adapter firmly into the slot then click OK N Max Wireless USB Adapter e Please insert wireless adapter into your computer Figure Insert wireless adapter 9 The Windows New Hardware wizard screen will appears click Next Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows will search for current and updated software by looking on your computer on the hardware installation CD or on the Windows Update Web site with your permission Read our privacy policy Can Windows connect to Windows Update to search for software Yes this time only Yes now and every time connect a device CO No not this time Click Next to continue 10 Select Install the software automatically Recommended to allow it to complete the installation of the Windows driver and then click Next N Max Wireless USB Adapter Found New Hardware Wizard This wizard helps you install software for LevelOne WUA 0601 N Max Wireless USB Adapter If your hardware came with an installation CD or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click to continue Figure Install the software automatically 11 If using Windows XP you may see a warning screen like the example below If you do see this screen just click Contin
9. Wireless networks Wireless Network Sequence order You can click the headings ex Network Name MAC Address Security of the Wireless network table to arrange the Wireless network in the desired order To Connect to a Wireless Network e Double click on the desired network e Click the name of the wireless network to which you want to connect and then click Connect Note that once you are connected to a Wireless network the Site Survey screen will identify the current wireless network with a blue icon as shown below 11 N Max Wireless USB Adapter LevelOne Wireless Utility WUA 0601 Site Survey Profile Manager 1 EET pub Wireless Site Survey Filter Display PC PC Ad Hac Display 802 11b Access Points b e Display 802 114 Access Points Display 802 119 Access Points Network Mame Address Security WPS CH Signal Network Type Fi Halga wBR BDDU 00 0 02 4 0 WEP 11 100 Infrastructure 2 tg 00 11 68 22 1 6E WEP 11 Infrastructure 1g WAP OO03 00 11 66 60 64 C5 WEP alz Infrastructure 2 WPG 1000 00 01 36 00 A4C C4 WEP 3 48z Infrastructure 2 t gn 00 002123584 00 0 02 1 2 35 88 WEP Y 1 44x Infrastructure 2 default ssid 00 11 66 39 05 86 1 40 Infrastructure 2 16 camera 00 19 58 43 29 8 WEP Infrastructure Figure Site Survey Screen Connected 12 N Max Wireless USB Adapter Profile Manager Screen This screen i
10. ces below Chinese Simplified Chinese Mind German Japanese InstallShield Figure Select language 5 On the screen below click Next to start the installation LevelOne 0601 InstallShield Wizard Welcome to the InstallShield Wizard for LevelOne WUA 0601 The InstallShield Wizard will install LevelOne WUA 0601 on your computer To continue click Next Cancel Figure Start Installation N Max Wireless USB Adapter 6 to install the program click Install to begin the installation LevelOne WU A 0601 InstallShield Wizard Heady to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exit the wizard Figure Ready to install the program 7 Click Continue Anyway on the screen below Software Installation AN The software you are installing has not passed Windows Logo testing to verify its compatibility with Windows Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the software vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Figure Installation Screen
11. e settings on this screen Please make sure to specific the Profile name 2 Verify that the settings you configured are correct 3 Click Save Profile To export profiles 1 Onthe Profile Manager tab click Export Profiles The Save As dialog box appears 2 name for the profile that you are saving and then verify that the file name extension is set to cfg 3 Click Save To import profiles 1 On the Profile Manager tab click Import Profiles The open dialog box appears 2 Select the profile set that you want to import 3 Click Open To delete a profile 1 Profile Manager tab select the profile that you want to delete 2 Click Delete Profile To edit a profile 1 Onthe Profile Manager tab select the profile that you want to edit 2 Change the profile settings as necessary 3 Click Save Profile To enable a profile 1 In the list of available profiles click the profile that you want to enable 2 Click Apply Profile 15 N Max Wireless USB Adapter Advanced Settings Screen Once you have created a profile as described above the Advanced Settings tab will be available on the Profile Manager screen Note Advanced settings only available when 11b g wireless mode has been selected Advance Settings Protocol Do not change settings Preamble 2 4GHz Transmit Rate Fragment Threshold 256 RTSICTS Threshold 258 802 11n Enable 802 11n Network Channel
12. from my access point Enterthe PIN 10904732 into your access point and click Start Button to continue Close 18 N Max Wireless USB Adapter Network Status Screen This screen displays the status of the current wireless link Clicking the Network Sta tus tab will display a screen like the following LevelOne Wireless Utility WU A 0601 Site Survey Profile Manager Network Status About Link Information Channel Performance Signal Current Status Connected Current Tx Rate 0 bps Network SSID WBR 6000 1 Kbps Network BSSID 00 C0 02 FF B4 0E Network Type Infrastructure 500 bps Security Mode WEP 0 bps Tx Aix Speed 150 Mbps 270 Mbps Internet Protocol TCP IP Cou nus hes DHCP Option Enable 1 Kbps IP Address 192 168 1 4 Subnet Mask 255 255 255 0 500 bps Default Gateway 192 168 1 1 DHCP Server 132 168 1 1 bps Auto Connect Figure Network Status Screen You may have to wait a few seconds for the screen to be populated Data Network Status Screen Link Information Current Status Network SSID Network BSSID Network Type Security Mode Speed Internet Protocol DHCP Option IP Address Subnet Mask Default Gateway It will indicate the current link status It shows the SSID or network name of the selected wire less network It shows the MAC address of the access point This will indicate Infrastructure or Ad hoc It shows the wireless securit
13. ient authen tication according to the 802 1x standard Data transmissions are encrypted using the WPA2 standard The available options depend on the Authentication method selected above The possible options are Security Off No data encryption is used WEP If selected you must enter the WEP data shown below This WEP data must match the Access Point or other Wireless stations AES TKIP These options are available with WPA PSK WPA2 PSK WPA Radius and WPA2 Radius Se lect the correct option Enable this check box and enter a word or group of printa ble characters in the Passphrase box select the desired encryption to automatically configure the WEP Key Enable this check box and select the desired key in the drop down list Then enter the key values you wish to use and select the desired encryption Other stations must have matching key values For WPA PSK and WPA2 PSK modes you need to enter the desired value 8 63 characters Other Wireless Sta tions must use the same key 14 N Max Wireless USB Adapter Confirm For WPA PSK and WPA2 PSK modes re enter the value in this field 802 1x Authentica For WPA Radius and WPA2 Radius modes select the tion Protocol desired option in the drop down list Configure WPA For WPA Radius and WPA2 Radius modes click this button Radius to open a sub window where you can enter details of the Radius Server To add a profile 1 On the Profile Manager tab complete th
14. igure Site Survey Screen 10 Network Type Infrastructure Infrastructure Infrastructure Infrastructure Infrastructure Infrastructure Infrastructure ReScan X N Max Wireless USB Adapter Data Site Survey Screen Display PC To PC Ad Hoc Display 802 11b Access Points Display 802 11g Access Points Network Name MAC Address Security WPS CH Signal Frequency Network Type Status Rescan Select this check box to display ad hoc computer to computer networks Select this check box to display 802 110 infrastructure net works Select this check box to display 802 11g infrastructure net works Available wireless networks are listed This is the MAC address of the Access Point or Wireless station if the network is an Ad hoc network Data encryption and authentication methods used on the wire less network This will indicate Y the Access Point with WPS function Y the WPS function of the Access Point is in used or the Access Point without WPS function The channel used by the Wireless network This is displayed as percentage 0 100 The Wireless band used by this Wireless network This will indicate Infrastructure displayed device is an Access Point or Ad hoc displayed device is a Wireless station The area to the left of the Rescan button shows the current status In the example above it shows Connected Click this button to rescan for all
15. mme diately Link Act LED USB Wireless Adapter The Wireless Adapter has a single Link Activity LED Link Act LED Associated with the network Off Not associated with the network e Blinking Data being transferred Introduction To eject the USB connector press the end of the orange button to slide out the USB connector To eject the USB connector press the end of the orange button to slide out the USB connector You should install the supplied software on the CD ROM before inserting the USB adapter Chapter 2 Initial Installation This Chapter covers the software installation of the USB Wireless Adapter e Windows 2000 XP Vista e Available USB port e CD ROM drive EEE802 11b IEEE802 11g or 802 11n Draft Wireless LAN IMPORTANT Do not insert the Adapter into your computer BEFORE installing the supplied software from the LevelOne CD 1 Insert the CD ROM into the drive on your PC 2 The installation program should start automatically it does not run autorun exe program 3 Select the WUA 0601 and click Utility on the screen N Max Wireless USB Adapter one world one brand one level Figure Select the Utility of WUA 0601 N Max Wireless USB Adapter 4 Select the desired installation language on the screen LevelOne WI A 0601 InstallShield Wizard Choose Setup Language Select the language for the installation from the choi
16. onnecting directly to another computer 13 N Max Wireless USB Adapter Wireless Mode Prefer Channel Authentication Mode Encryption Method Create with Pass phrase Enter Key Manually Passphrase Select the desired wireless mode to which you want to connect This option only available under Ad Hoc mode it allows user to select the prefer channel Select the channel you would like to use under Ad Hoc mode Channel 1 13 You MUST select the option to match the Wireless LAN you wish to join The available options are Open System Broadcast signals are not encrypted This method can be used only with no encryption or with WEP Shared Key Broadcast signals are encrypted using WEP This method can only be used with WEP Auto Switch This is another WEP system it will select either Open System or Shared Key as required WPA PSK PSK means Pre shared Key You must enter this Passphrase value it is used for both authenti cation and encryption WPA2 PSK This is a further development of WPA PSK and offers even greater security You must enter this Passphrase value it is used for both authentication and encryption WPA Radius This version of WPA requires a Radius Server on your LAN to provide the client authentication according to the 802 1x standard Data transmissions are encrypted using the WPA standard WPA2 Radius This version of WPA2 requires a Radius Server on your LAN to provide the cl
17. ould be set to use the same Channel However most Wireless stations will still scan all Channels to see if there is an existing Ad hoc group they can join WEP amp WPA PSK Both WEP and WPA PSK are standards for encrypting data before it is transmitted This is desirable because it is impossible to prevent snoopers from receiving any data which is transmitted by your Wireless Stations But if the data is encrypted then it is meaningless unless the receiver can decrypt it WPA PSK is a later standard than WEP and is more secure Wireless LAN Configuration To allow Wireless Stations to use the Access Point the Wireless Stations and the Access Point must use the same settings as follows Mode On client Wireless Stations the mode must be set to Infrastructure The Access Point is always in Infrastructure mode SSID ESSID Wireless Stations should use the same SSID ESSID as the Access Point they wish to connect to Alternatively the SSID can be set to any or null blank to allow connection to any Access Point Security The Wireless Stations and the Access Point must use the same settings for Wireless security Disabled WEP WPA PSK WEP If WEP is used the WEP Key must be the same on the Wire less Stations and the Access Point WEP Authentication Open System or Shared Key must also be the same unless the Access Point supports both methods simultaneously WPA PSK If using WPA PSK the PSK Pre shared Key
18. posure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncon trolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body This device complies with Part 15 of the FCC Rules Operation is subject to the follow ing two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This transmitter must not be co located or operating in conjunction with any other antenna or transmitter CE Marking Warning Digital Data Communications declares that this product Model no WNC 0601 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The CE Declaration of Conformity can be downloaded at http www levelone eu support php ii Table of Contents CHAPTER 1 INTRODUGCTION 2 2 2 232 ae ce booa 1 Package COhItellls ooo ie aa Dave pu Locus o iu eis 1 1 ES 2 CHAPTER 2 INITIAL INSTALLATION 3 te 3 POC CCUG m M 3 CHAPTER USING THE WINDOWS UTILITY eeeee erre eene eene 9 OVEIVIENW uocis IND
19. pter Model LevelOne WUA 0601 Wireless USB Adapter Bus Type USB 2 0 20 MHz BW 130 117 104 78 52 39 26 13 802 11n 40 MHz BW 300 270 243 216 162 108 81 54 27 Data Rates 54 48 36 24 18 12 9 and 6 Mbps 802 119 11 5 5 2 1 Mbps 802 11b Frequency Band 2 4GHz to 2 5GHz Wireless Medium 0555 and OFDM ipi Access Proto CSMA CA Draft 802 11n BPSK QPSK 16 QAM 64 QAM 802 11g OFDM CCK QPSK BPSK Access Proto CSMA CA 14 1 dBm 14 1 dBm 17 1 dBm WEP 64 128 WPA PSK WPA2 PSK WPA Radius WPA2 Radius 22 About Wireless LANs This Appendix provides some background information about using Wireless LANs WLANSs Wireless LANs can work in either of two 2 modes e Ad hoc e Infrastructure Ad hoc Mode Ad hoc mode does not require an Access Point or a wired Ethernet LAN Wireless Stations e g notebook PCs with wireless cards communicate directly with each other Infrastructure Mode In Infrastructure Mode one or more Access Points are used to connect Wireless otations e g Notebook PCs with wireless cards to a wired Ethernet LAN The Wireless Stations can then access all LAN resources Access Points can only function in Infrastructure mode and can communicate only with Wireless Stations which are set to Infrastructure mode 55 55 55 group of Wireless Stations and a single Access Point all using same ID 5510 form
20. s accessed by clicking the Profile Manager tab on the main screen LevelOne Wireless Utility WU A 0601 Site Survey Profile Manager Network Status Profile Setting Profile N ame Security WUA DBUT Authentication Mode WPA PSK Network Name SSID Encryption Method AES WBR 6000 v2 Advance Settings WPS Function Enter 8 63 Characters Network Type Passphrase eeeeeces 9 Infrastructure Ad Hoc Confirm 00000000 Import Profiles Export Profiles Delete Profile Save Profile Apply Profile Auto Profile Connect x Close Figure Profile Manager Screen Data Profile Manager Screen Profile Name Enter or select a suitable name for this profile Each profile must have a unique name before user can actually save the profile Network Name If the desired wireless network is currently available you SSID can select its SSID Otherwise type in the SSID of the desired wireless network Advanced Settings On the resulting sub screen enter the required data for the advanced settings Advanced settings only available under 11b g wireless environment WPS Function WPS Wi Fi Protected Setup can simplify the process of connecting any device to the wireless network by using the push button configuration PBC on the Wireless Access Point or entering an 8 digit PIN code Network Type select the desired option e Infrastructure Select this to connect to an Access point Ad Hoc Select this if you are c
21. tori Radio Off WZC On Exit Figure Wireless Adapter menu N Max Wireless USB Adapter Connecting to a Wireless Network Double click the Icon to open the Site Survey screen when you can select the Wireless network you wish to join Auto Connect Normally this option should be enabled The adapter will then connect to an available network which was connected successfully last time There are various methods to specify the required network e Profile Manager tab select the desired profile in the list and click the Apply Profile button Site Survey tab either double click the network in the list or select the network and click the Connect button Site Survey Screen This screen is displayed when you double click the system tray icon You can also click the Site Survey Tab in the screen LevelOne Wireless Utility WUA 0601 pu Site Survey Profile Manager Network Status Wireless Site Survey Filter Display PC To PC amp d Hoc Network Name Address WBR 6000 00 0 02 4 0 ig 00 11 6B 22 17 6E WA amp P 0003 00 11 66 60 64 C5 WPG 1000 00 01 36 0 4 gn 000002123589 00 0 02 1 2 35 88 default ssid 00 11 68 39 05 86 camera 00 19 58 43 29 8 Security WEP WEP WEP WEP WEP None WEP C Auto Profile Connect Display 802 11b Access Points Display 802 119 Access Points CH 11 11 5 DisConnect F
22. ue Anyway Hardware Installation AN The software you are installing for this hardware Level ne WUA 0601 Max Wireless USB Adapter has not passed Windows Logo testing to verify its compatibility with Windows Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Figure Windows XP Warning N Max Wireless USB Adapter If the wizard can not Install the driver automatically please search for driver in the default location The driver is located in C Program Files LevelOne WUA 0601 Driven directory 12 When the Wizard has finished installing the software click Finish Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for Hia LevelOne WUA 0601 Max Wireless USB Adapter Click Finish to close the wizard Figure Complete the Found New Hardware Wizard 13 When the Windows wizard is complete you will now have a new icon in your sys tem tray as shown below 2 26 AM Figure System Tray Icon USB Wireless Adapter Icon Table Connection to the USB Wireless Adapter is established The length of green color indicates the
23. y that the wireless network is using It shows the current wireless connection speed It shows if the IP address was automatically obtained from a DHCP server It shows the current IP address on the wireless interface Subnet mask for the current IP address Gateway IP address associated with the current IP ad dress 19 N Max Wireless USB Adapter DHCP Server It shows the IP address of the DHCP Server Channel Performance Channel Perfor It graphically presents the Transmission Tx rate and mance Receiving Rx rate over time Signal Signal It graphically presents the Signal strength The Channel Performance diagram indicates the real time TX and RX 20 N Max Wireless USB Adapter About Screen This screen displays details of the traffic sent or received on the current Wireless network LevelOne Wireless Utility WI A 0601 Site Survey Profile Manager Network Status Visit LevelOne Website Wireless Adapter Information Firmware Version Driver Version 1100 11 15 2007 MAC Address 00 0 02 FF C5 B4 Utility Information LevelOne DLL Version 18 1 40 2 14 2008 LevelOne Utility Version 1 8 2 36 2 14 2008 Auto Profile Connect Figure About Screen This tab shows the following information e Regional Domain e Firmware Version e Driver Version e MAC Address e LevelOne DLL Version LevelOne Utility Version 21 Appendix Specifications USB Ada
Download Pdf Manuals
Related Search