LACANCHE KITCHEN RANGE HOODS
Contents
1. Do not use abrasive cleaners Epoxy coated casing_ Sponge with soapy solution USER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 26 28 CLEANING AND MAINTENANCE Fluorescent tube replacement Pull to unclip diffuser and replace tube Push diffuser back in place Use PL 15W compact fluorescent replacement tubes for range hood models 15W L2HM 1200 to 1600 PL 11 W tubes for range hood models L2HM 900 L2HM 1700 to 2200 USER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 97 28 Note concerning the disposal of waste electrical and electronic equipment Decree no 2005 829 of 20 July 2005 transposing European Directives 2002 95 EC and 2002 96 EC on hazardous substances in electrical and electronic equipment and on the disposal waste electrical and electronic equipment a Electrical and electronic equipment EEE and waste electrical and electronic equipment WEEE are regulated at European level by two directives which aim on the one hand to limit the use of certain hazardous substances in EEE and on the other hand to promote the reuse recycling and other forms of recovery of WEEE so as to reduce the disposal of waste All electrical and electronic equipment put on the market after 13 August 2005 must be marked with this symbol This symbol indicates that the equipment may not be disposed of with other waste and that it is the object of separate collection w2. remaining screws on covers and f INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 22 28 HOTTES USER S MANUAL IMPORTANT This appliance is intended for professional use and must be used by qualified persons It must be installed in accordance with the applicable regulations and standards in an adequately ventilated room Any changeover to a gas other than that for which the appliance is set up must be carried out by a qualified installer Any changeover to a voltage other than that for which the appliance is set up must be carried out by a qualified installer WARRANTY The warranty is stated on the sales contract Please contact your approved Dealer if any work has to be carried out under warranty This warranty excludes damage resulting from incorrect installation improper use or inadequate servicing Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 23 28 USER S MANUAL USE 25 CLEANING AND MAINTENANCE 26 Note concerning the disposal of waste electrical and electronic equipment 28 This range has the C marking i e it meets the essential requirements of the Euro pean safety directives to which it is subject Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 24 28 USE Operating principle LACANCHE range hoods are available with a single LHM 900 or two 600 m h blower units other models and are supplied complete with grease filters T
3. the 4 screws on either side of the unit fig see assembling the unit s section n jjj i D j Put the sheath in place figure Aa Adjust the grip ring figure 45 19 28 Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 INSTALLER S MANUAL INSTALLING THE EXTRACTOR HOOD EXTENSION See rating of 250 from your ceiling and adjust the media hides sheath in boutonni ress provided for this purpose and adjust the height of the plastic cylinders by screwing or unscrewing figure 46 A INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 20 28 INSTALLING THE EXTRACTOR HOOD EXTENSION S y ACANCH E gt S OP Then adjust the jacks until the extractor hood extension is pressed against the ceiling figure 49 Caution Do not force the jacks when tightening Replace the media cover and secure Replace the front facing of the extractor hood by performing the above operations in reverse order aches beams Right and Left Cache front beam INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 21 28 INSTALLING MOUNTING CHANNEL COVERS Hold cover lt in place and fasten back of cover using a stainless steel M5 screw Hold cover 1 in place and fasten back of cover using a stainless steel M5 screw Install third cover nd fasten to blower unit mounting bracket using 2 stainless steel M5 screws Install
4. E 4 4 4 8 8 8 8 4 4 4 4 8 L2HM 1000 E L2HM 1100 E L2HM 1200 E L2HM 1300 E L2HM 1400 E L2HM 1500 E L2HM 1600 E L2HM 1700 E 8100 20 L2HM 1800 E 810 L2HM 2000 E T 7 T 7 T f T 7 T 7 7 T 8 8 8 8 8 8 TECHNICAL DATA SHEETS MEASUREMENTS AND DIMENSIONS Connecting exhaust duct Attention Cut exhaust duct s and make sure duct when run through the hole in the base of the installed hood protrudes far enough to be connected to the fan s Electric connection Finish cable with an earthed 2 pole plug suitable for 230V 1N 50Hz Hood must be earthed Power input L2HM 900 1100 120 Watt when lit L2HM 1101 1601 235 Watt when lit L2HM 1701 2002 240 Watt when lit L2HM 2102 2202 470 Watt when lit Directives Low Voltage 2006 95 CEE CEM 2004 108 CEE INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 5 28 L2HM 900 L2HM 1000 L2HM 1100 L2HM 1200 L2HM 1300 L2HM 1500 L2HM 1600 L2HM 1700 L2HM 1700 L2HM 1800 L2HM 2000 L2HM 2100 L2HM 2200 L2HM 2400 INSTALLER S MANUAL Appliances must be installed in a workmanlike manner in accordance with the instructions in this manual and locally applicable regulations This manual will be handed over to the user after installation Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 7 28 SITTING bs y ACANCH E gt S OQ
5. LACANCHE KITCHEN RANGE HOODS L2HM 900 L2HM 1000 L2HM 1100 L2HM 1200 L2HM 1300 L2HM 1500 L2HM 1600 L2HM 1700 L2HM 1700 L2HM 1800 L2HM 2000 L2HM 2100 L2HM 2200 L2HM 2400 Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 1 28 TECHNICAL DATA SHEETS MEASUREMENTS AND DIMENSIONS INSTALLER S MANUAL 7 SITTING SETTING UP THE HOOD SETTING UP OF GROUPS INSTALLING THE EXTRACTOR HOOD EXTENSION INSTALLING MOUNTING CHANNEL COVERS USER S MANUAL 23 USE CLEANING AND MAINTENANCE Note concerning the disposal of waste electrical and electronic equipment Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 13 17 20 22 25 26 28 2 28 TECHNICAL DATA SHEETS MEASUREMENTS AND DIMENSIONS 305 Axe de sortie centrale L Hotte LHM 22b Axe de sortie centrale Hotte LHME Axe de sortie murale E LO CTS Hotte LHME NE LO e ECH Raccordement lectr Hotte LHM LHME 580 Axe de sortie murale ca Hotte LHM LHME Se eee mmm m 1820 UJ rr e A B L2HM900 900 385 INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 3 28 TECHNICAL DATA SHEETS MEASUREMENTS AND DIMENSIONS gt LACANCHE KITCHEN RANGE HOODS Decorative single and double blower unit kitchen range hoods in canopy widths from 900 to 2 000 mm CAUTION Under no circumstances shall the distance between the exhaust hood and the
6. The purchaser undertakes to install or arrange for his her equipment to be installed in a workmanlike manner and in accordance with the applicable regulations and standards Any servicing or repair work on appliance must be performed by a qualified technician Cautions Shipment Packaging Carton packing crate on wooden palette Unpack and check the appliance is in good condition In case of damage note any reservations on the delivery note and confirm them within 48 hours by registered letter with confirmation of delivery to the carrier Recommendations Check hood overhead clearance Install elbow over hood when mounting a complete range hood connected to a wall exit Do not connect exhaust duct to central ventilation system or service duct Choose shortest and straightest pathway for exhaust duct In case of insufficient air renewal rate blower may create low indoor pressure causing up to 50 performance loss Provide and install proper damper when connecting fan exhaust to wall exit INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 9 28 SITTING LACANCHE range hoods install horizontally at a minimum distance of 65 cm over electrical range 80 cm over gas range Make sure hood is installed perfectly horizontal and cannot dip forward Use aluminum duct and choose shortest and straightest pathway Do not connect to smaller diameter duct use no roof caps or exhaust s
7. creens A Z M R N SC BAD MEDIUM GOOD Extractor hood extension Attachment plate Plastic jack x 4 Front INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 10 28 INSTALLATION Preparing the extractor hood 1 Turn the extractor hood onto its back figure 1 INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 11 28 INSTALLATION 3 Stand the extractor hood upright 4 Remove the front cover by lifting it slightly and pulling it toward you figure 3 INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 12 28 SETTING UP THE HOOD Installing hood 1 Trace and drill holes figure 4 2 Positioning and securing the two brackets to hood screw type M5 Axis of the hood nod 100 100 1100 100 100 60 60 length of the hood 420 mm to position if back panel 2356 1799 INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 13 28 SETTING UP THE HOOD NOTE If a back cover is used install the back cover before mounting the hood 5 O O Axis of the hood 2356 1820 Attach the trim back the hood before INSTALLERS MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 14 28 SETTING UP THE HOOD 3 Hang the hood to hood profile support 4 Insert the screws 6532570 and 6535377 figure 6 and 7 5 Tigh
8. he glass center intake panel defines the air path into the hood For normal operation Place pans on range so hood catches all vapor and smoke Avoid cross drafts Match fresh air intake to exhaust volume to avoid loss of performance Controls The control panel of each blower unit features a 5 position rotary switch O Off light I Il and III blower speeds Select required blower speed CH 1 P een EUM A Fr gt E a Es dh k A v d a i 1 _ N E 7 v H CAUTION NEVER FLAME UNDER HOOD USER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 25 28 CLEANING AND MAINTENANCE BEFORE ANY CLEANING OPERATION CHECK THAT THE APPLIANCE IS DISCONNECTED FROM THE SUPPLY CAUTION Do not use a steam cleaner to clean the appliance Carefully read the precautions and recommendations for applying the products you use to clean and maintain the range Follow the instructions for use Clean grease filters at least once a month and more frequently in case of intensive use Unclip bottom A and pull filter tabs P Soak grease filters a few minutes in a hot water and ammoniated detergent or soda solution then hold filters by pin and tap to dislodge particles Rinse and hold against light to inspect for residual clogging Install filters and run blower to dry Stainless steel casing_ Use special stainless steel cleaners ZIP INOX JOHNSON INOX PPZ INOX for instance
9. ith the purpose of recovery reuse and recycling a Users of electrical and electronic equipment are required not to dispose of WEEE as unsorted municipal waste a Appropriate systems of separate collection are available to users a To meet these regulations as a manufacturer of electrical equipment Lacanche has joined and participates in the green scheme operated by ECO SYSTEMES FRANCE It is by observing these regulations that users of electrical and electronic equipment avoid the potentially harmful effects on the environment and human health whilst contributing also to the preservation of natural resources INSTRUCTION MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 28 28
10. ten the screws lightly to flatten 6553377 hood to the wall 6 To level by tightening or loosening the 2 screws 6532570 and 6535377 7 End of the hood to the wall plate by tightening the screws 6535377 6535377 6532570 NGGI Fee GE E See _ Tf lS a oe INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 15 28 SETTING UP THE HOOD Ce ce nean de ra mandatory attachments INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 16 28 SETTING UP OF GROUPS Installing blower unit s figure and 9 Remove glass center intake panel Loosen black side cover screws T Loosen 8 screws Push blower unit s into cutout until they bottom with rotary switch facing forward and to the right Make sure locking lugs hold blower unit s securely in place Tighten screws item and 1 INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 17 28 SETTING UP OF GROUPS Setting up in the hood fi ure 40 Remove the 4 screws on media panels and drop media panels y Media panel Prepare the extractor unit and use the locking brackets to position it item figure D and 42 see RS g assembling the unit s section 18 28 Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 INSTALLER S MANUAL SETTING UP OF GROUPS Fasten the extractor unit s to the hood by tightening
11. wall or ceiling exhaust opening exceed 9 metres Make sure that the support surface and fixings used are able to take the weight of the hood Before drilling any holes make sure that there are no electric cables gas pipes or other ducts or piping running through the wall in the areas concerned As far as possible it is advisable to mount the hood on a solid support surface Stainless steel or black white or color epoxy coated shell Adjustable duct cover Single L2HM 90 1100 or double blower units other models featuring Max sound levels of 52 dB A at 1 m of unit Top or side exhaust Blowers Blower units Exhaust duct Air flow pressure ratio diameter 327 m 384 Pa 327 m 384 Pa 327 m 384 Pa 627 moi 383 Pa 627 moi 383 Pa 627 moi 383 Pa 627 m 383 Pa 654 m 384 Pa 654 m3 384 Pa 654 moi 384 Pa 654 m 384 Pa 576 m 380 Pa 576 m 380 Pa 655 m 364 Pa 655 m 364 Pa 655 m 364 Pa 655 m 364 Pa 655 m 364 Pa 655 m 364 Pa 1152 m 380 Pa 1152 m 380 Pa L2HM 2100 E 1152 m 380 Pa L2HM 2400 E 1310 m3 364 Pa INSTALLER S MANUAL Hottes Ft 118a GB R v 08 Modifi le 06 07 2015 4 28 L2HM 900 874 L2HM 1000 874 L2HM 1100 874 L2HM 1200 878 L2HM 1300 878 L2HM 1500 878 L2HM 1600 878 L2HM 1700 874 L2HM 1800 874 L2HM 2000 874 L2HM 2100 874 L2HM 2400 878 8 8 8 8 8 8 8 8 8 8 8 8 L2HM 900
Download Pdf Manuals
Related Search