Field Guide
Contents
1. Hand tighten only Using tools could damage equipment d Verify that the red dot is present by turning the rotary switch clockwise Mounting Procedure a Select a groove on the rail that will give you a correct position for the sight Ensure that the groove is undamaged and clear of dirt and sand b Loosen the torque knob 10 by turning it counterclockwise c Install the mount and sight on the rail fig 2 Make sure that the mount is correctly positioned and that the recoil stop is in the selected groove d Push the mount forward fig 3 The recoil stop shall be in contact with the front edge of the groove e Tighten the torque knob fig 4 clockwise until it snaps twice This ensures that the mount is secured NOTE Grasp the checkered portion of the knob only to prevent pinching of fingers when the shaft opens and snaps shut f Test fire the weapon with the sight mounted Retighten the torque knob 10 after a few rounds if necessary g Perform complete zeroing procedure according to 2 2 12. battery Remove and reinstall battery with toward cap Battery is not making good contact Clean contact surfaces and reinstall battery Defective rotary switch Notify gunsmith or local Aimpoint Dealer 4 2 Impossible to zero Adjustment screw is at its limit Check alignment of mount to barrel Impact point is moving Check mount stability CHAPTER V MAINTENANCE a This reflex sight does not require any particular maintenance when used under normal conditions b Under severe weather conditions please refer to chapter Ill c Keep lens covers closed whenever the sight is not in use d Long term storage Remove battery from sight Allow lens surfaces to dry completely if wet before closing the lens covers e To clean lenses refer to caution in CHAPTER III lt j Q Dx Aimpoint User s manual for Aimpoint PRO Patrol Rifle Optic Aimpoint AB Aimpoint Inc Jagershillgatan 15 14103 Mariah Court SE 213 75 Malm Sweden Chantilly VA 20151 2113 USA Phone 46 0 40 671 50 20 Phone 1 703 263 9795 Fax 46 0 40 21 92 38 Fax 1 703 263 9463 e mail info aimpoint se e mail info aimpoint com www aimpoint com www aimpoint com THE FUTURE IN SIGHT Copyright 2014 Contents property of Aimpoint All rights reserved 13648 1 CHAPTER 1 1 PRESENTATION The Patrol Rifle Optic PRO is a rugged precision electronic red dot sight developed for civilian military and law enforce
3. 2 2 OPERATING PROCEDURES 2 2 1 Zeroing Aimpoint sights are delivered in a centered position Normally this means that only small adjustments are necessary providing that the sight base is properly aligned with the rail CAUTION To prevent damage to your sight do not continue to adjust windage and elevation mechanisms if you encounter resistance The elevation adjustment screw is located on top of the sight while the windage screw is located on the right side of the sight pos 4 and 5 a Open front and rear lens covers b Turn the rotary switch clockwise until the red dot has sufficient intensity to contrast against the target c Remove the windage and elevation adjustment caps NOTE Each click of the adjustment screw corresponds to a 10 mm movement of the point of impact at 80 meters 3 mm at 25 meters 13 mm at 100 meters and 25 mm at 200 meters or 1 4 at 50 yds 1 2 at 100 yds and 1 at 200yds d Insert adjustment tool coin screwdriver knife or empty cartridge casing in adjustment screw slot and turn as follows e To move the point of impact to the right turn windage adjustment screw counterclockwise e To move the point of impact to the left turn windage adjustment screw clockwise e To move the point of impact up turn elevation adjustment screw counterclockwise e To move the point of impact down turn elevation adjustment screw clockwise e Confirm zeroing by firing at least three shots at a zer
4. ature 130 mm 5 1 55 mm 2 2 55 mm 2 2 220 grams 7 8 oz 330 grams 11 6 oz including mount and spacer Range 2 m at 100 meters in windage and elevation 1 click 10 mm at 80 meters 13 mm at 100 meters 1 2 at 100 yards 45 C to 71 C 50 F to 160 F Submersible to 45 m 150 ft water depth MOA Minute Of Angle 1MOA 30 mm at 100 meters 1 at 100 yards NVD Night Vision Device 1 3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS AND FUNCTIONS 1 Battery Cap 9 QRP2 Mount 2 Battery DL1 3N or similar 10 Torque knob 3 Cover for adjustment screw 11 Mounting Screw 4 Adjustment Screw elevation 12 Ring Mount 5 Adjustment Screw windage 13 Rotary Switch 6 Lens Cover rear 14 Strap 7 Lens Cover front 15 Mounting Screw short 8 Removable Spacer 16 Allen Wrench for screws 15 CHAPTER II 2 1 OPERATION UNDER NORMAL CONDITIONS Assembly and preparation for use WARNING Ensure the weapon is cleared unloaded and the safety selector is in the safe position before attempting to install remove or perform maintenance on the sight Installing Battery a Remove battery cap by turning it counterclockwise b Insert battery with positive end toward cap Before installing battery cap inspect that the o ring is present and not damaged Failure to do so could result in water leakage into the battery compartment c Install battery cap by turning clockwise until snug
5. ment applications Aimpoint sights are designed for the both eyes open method of sighting which greatly enhances situational awareness and target acquisition speed Thanks to the parallax free design the dot follows the movement of the user s eye while remaining fixed on the target This eliminates any need for centering the dot in the sight tube The sight is designed for unlimited eye relief allowing the sight to operate at any distance from the user s eye The PRO is compatible with 1st 2nd and 3rd generation night vision devices NVD If you have further questions please contact your gunsmith or local Aimpoint Dealer 1 2 SPECIFICATION Material housing Material lens covers Surface finish Optical magnification Eye relief Optical coating Dot size Switch dot brightness Battery Battery life Length incl lens covers Width Height Weight sight only Weight with integrated mount Adjustment Max temperature range Water resistance Extruded high strength aluminum anodized Thermoplastic elastomer black non glare Hard Anodized Dark Graphite Grey matte 1X Unlimited no centering required Anti Reflex coating all surfaces Multi layer coating for reflection of dot Band Pass coating for NVD compatibility 2 MOA 10 positions 4 NVD 6 daylight of which 1 Extra Bright One 3 Volt Lithium battery type 2L76 or DL1 3N 3 years on setting 7 out of 10 at room temper
6. oing target Check impact points on zeroing target to confirm accuracy and repeat above procedure if required f After initial firing ensure that the mount and sight are secure g Turn rotary switch to OFF position counterclockwise h Close front and rear lens covers i Replace adjustment screw caps CHAPTER III OPERATION UNDER EXTREME CONDITIONS a Extreme heat moist or dry No special procedures required b Extreme cold Extreme cold might shorten battery life c Salt air No special procedures required d Sea spray water mud and snow Ensure that battery cap and both adjustment screw caps are tight before exposing the sight to sea spray mud snow or before immersing the sight in water Hand tighten only Keep lens covers closed when sight is not being used Clean lenses with lens paper cloth and wipe the sight dry as soon as possible after exposure to water sea spray mud or snow e Dust storms and sand storms Keep lens caps closed when sight is not being used f High altitudes No special procedures required CAUTION The lenses should never be cleaned with fingers use a lens paper cloth If no lens paper cloth available To clear away debris sand grass etc blow away the dirt To clean lenses mist up the lenses and dry them with a clean and soft piece of cloth CHAPTER IV TROUBLE SHOOTING PROCEDURES 4 1 Red dot does not appear Discharged battery Battery installed incorrectly Replace
Download Pdf Manuals
Related Search