[RTX4002 DECT Repeater]
Contents
1. Auto registration 1 Ensure that the repeater is switched off disconnect the power plug 2 Set the base station in registration mode On most base stations the procedure is started by holding down the Registration or Page key for several seconds Consult your base station user guide for more information 3 Switch on the Repeater connect the power plug 4 The LED on the Repeater flashes After a short while the LED stays on permanently indicating that registration is complete and the unit is ready for operation Note If the registration is not immediately successful the LED will flash continuously In this case repeat the procedure Note Before reinstalling the Repeater e g at an other basestation please reset the Repeater beforehand as described below 1 Switch off the unit disconnect the power plug 2 Switch on for 1 to 5 seconds and switch off again 3 Switch on for 25 to 35 seconds and switch it off again Now the Repeater is ready for a new auto registration Manual registration The repeater registration procedure varies depending on the base station installed The base station a mobile unit handset and the repeater must be accessible before registration can be performed If you are connecting more than one repeater registration must be performed separately for each repeater Preparations The base station and a mobile unit are ready for operation the repeater is not yet connec2. RTX4002 DECT Repeater A repeater is used when you need to extend the range of your cordless DECT telephone to include areas where reception was previously not available All the usual mobile unit functions are supported by the base station in this extended radio range The repeater and base station have wireless connections with each other just as the repeater and handset have wireless connections Signals are exchanged without the user hearing or noticing the difference D System with multiple repeaters Up to 6 repeaters can be registered at a base station The number of mobile units to be operated only depends on the type of the base station installed All repeaters must be installed within the base stations coverage area as shown in the drawings It is not possible to install repeaters in series The repeaters can be used to extend the coverage area in all directions including up and down e g to cover several floors in a building If the repeaters are placed correctly overlapping the coverage area of the base station you can go from one area cell to the other while speaking on the mobile unit The mobile unit will automatically switch from cell to cell without this being noticed during the telephone call Before the repeater is installed it must be registered to the base station The Repeater can be registrated to a basestation in two ways automatic or manual registration a Ge Om of
3. independent of the mobile unit extension numbers Hook off by pressing the key the LED stops flashing Press a number between 2 and 7 When the repeater has accepted the chosen number the LED will flash a corresponding number of times Accept the registration by pressing the key and then the O _ key hook on The repeater is now automatically restarted The LED goes off for 2 seconds flashes for a brief moment and the remains continuously illuminated The registration of the repeater is completed You can now disconnect the power and move the repeater to the selected location disconnecting the power will not delete the registration Placement To get the best operation conditions for the repeater it is important to place it correctly Here are a few tips for placing repeaters Choose a raised position with good base station reception When positioning you should avoid obstacles that can interfere with a radio transmission such as thick walls radiators etc You should avoid interference from other electrical appliances such as micro wave ovens hi fi equipment computers etc close to an electric socket A distance of minimum 10 meter s hould be observed when installing two repeaters in an overlapping reception range To find the best possible location for the repeater you have to try different locations Establish a call and walk around with the handset to determine the base stations cove
4. epends on the type brand of the base station RTX4002 DECT REPEATER Fe E 2 lt
5. rage area You can install the repeater at a location in the edge of the coverage area where you still have a good connection between the handset and the base station A new coverage area will now be available around the repeater Note The LED must remain on constantly after the device has been switched on If the LED flashes the repeater is too far away from the base station or reception is being hindered by thick walls or metal objects e g radiators Verification tone The verification tone enables you to establish whether or not the mobile unit is working in the extended area of the repeater This tone is audible on the activated mobile unit as long as the unit is connected to the repeater Carry out the procedure described below on your repeater in order to switch the verification tone on and off Switch off the unit disconnect the power plug Switch on for 1 5 seconds and switch it off again Switch on again The LED on the unit is flashing slowly switch off again Switch it on again The verification tone is then activated or deactivated Maintenance Simply wipe the repeater with a damp cloth or an antistatic wipe Never use solvents or a dry cloth static discharge Manual 4002_DECT_repeater p65 04 2001 PN95100805 Automatic Registration Base station Switch on Ready for use Manual Registration Base station Switch on Ready for use C 4 EEC Directive No 91 263 and No 93 68 1 D
6. ted to the main supply The following procedure is also shown as a quickguide on the back of this user manual 1 Set the repeater in registration mode Insert the repeaters power plug for 1 5 seconds in the socket and then remove it Insert it once more and leave it there The LED on the repeater flashes slowly after the start You now have five minutes to carry out the registration If the procedure is not carried out within this period you must start over again 2 Set the base station in registration mode On most base stations the procedure is started by holding down the Registration or Page key for several seconds Consult your base station user guide for more information 3 The LED on the front of the repeater flashes If the LED flashes very quickly without interruptions go to step 5 If the LED flashes very quickly with brief interruptions go to step 4 4 Registration of the handset If the base code have been changed it must be set to 0000 You must repeat the registration procedure even if the mobile unit used was already registrated at the base station consult your base station user guide for more information Now the LED flashes very quickly without interruptions 5 Assign a repeater number You must now assign a repeater number to the repeater selection 2 7 for up to 6 repeaters Please note that each number only can be assigned once when using more than one repeater These numbers are
Download Pdf Manuals
Related Search