JMY611G User`s Manual
Contents
1. amp ISO7816 Module http www jinmuyu com Antenna model Size of antenna Card operating distance TX600 70mm 70mm 90mm TX601 50mm 50mm 70mm TX602 30mm 30mm 60mm 3 5 Model available e JMY611GT UART interface TTL level e JMY611GS RS232C UART interface RS232 level e JMY611GU USB USB to RS232C Bridge 3 6 Model rule 3 6 1 Model format 1 2 3 4 JMY 611 X X 1 company code 2 product series code 3 card operating type 4 communication port type 3 6 2 Card operating type M PCD is RC500 support Mifare Class A PCD is RC500 support ISO14443A and Mifare Class C PCD is RC531 support ISO14443A ISO14443B and Mifare Class G PCD is RC400 support ISO15693 H PCD is RC632 support ISO15693 ISO14443A ISO14443B and Mifare Class D PCD is RC500 support ISO14443A and Mifare Class with 511 bytes communication buffer E PCD is RC531 support ISO14443AB and Mifare Class with 511 bytes communication buffer F PCD is RC632 support ISO15693 ISO14443A ISO14443B and Mifare Class with 511 bytes communication buffer 3 6 3 Communication port T UART S RS232C U USB Copyright 2003 2014 Jinmuyu Electronics Co LTD All rights reserved 5 62. D All rights reserved 2 6 ISO15693 amp ISO7816 Module http www jinmuyu com 3 Physical parameter and pin outs 3 1 Photo CZ RISRIBRII a2 C24C26C27C25 QUIE ms kJ LE wowi Be p Cice Eaz fe aema RU nies 8 ri l n IO C4 2 j qeu ire Ait E SESInIm epi rr e Li 5 o gt quii _ V gt i UL TITTEN Leeeceereretecee ul A M A R m aeri 4 as Copyright 2003 2014 Jinmuyu Electronics Co LTD All rights reserved lt ISO15693 amp ISO7816 Module 3 2 Dimension 3 3 Pin configurations and pin outs http www jinmuyu com 11 0 0 2 7 25 2 4 15 40 5 5 30 Pin number Function Type Description 1 TXD D Output RS232C TXD USB D 2 RXD D Input RS232C RXD USB D 3 VCC Power VCC 4 GND Power GND 5 GND Power GND 3 4 Outside Antenna Normally as the size of TX600 series antenna may not meet the actual demands the antenna needs to be customized especially in some compact systems The following information for customization is needed 1 Dimension of the antenna PCB 2 the position and direction of the antenna outlet and the connector 3 the description of the antenna periphery Jinmuyu will design the most proper antenna according to the user s exact requirements Copyright 2003 2014 Jinmuyu Electronics Co LTD All rights reserved 4 6 lt ISO15693
3. JMY611G User s Manual Revision 3 50 Jinmuyu Electronics Co LTD 2011 6 27 A Please read this manual carefully before using If any problem please mail to Jinmuyu vip sina com ISO15693 amp ISO7816 Module Contents Produ ctintroductlODo un diii sepes reete rettet rette cevesecaceresecsstessevscensceess 2 ChatacteristlCs 21 e eere oer Eh oe Rino t e I ova nva e I atu seubdesdadbactdasceaaueas 3 1 IPD OL sgt EE 3 2 ISSUE 3 3 Pin configurations and pin outs esse 3 4 Outside Antenna 5 n rrr t eee eere tere ens 3 5 Model available ieri rti I e Re eir RARE IRE 3 6 ibn bur A 3 6 1 Model format uesite enanas 3 6 2 Card operating type essere 3 6 3 Communication port eseeseeseeseeeeeeee eren Copyright 2003 2014 Jinmuyu Electronics Co LTD All rights reserved http www jinmuyu com 1 6 lt ISO15693 amp ISO7816 Module 1 Product introduction http www jinmuyu com JMY611G is a RFID read write module with UART RS232C or USB port JMY611G has various functions and supports multi ISO IEC standard of contactless card The RF protocol is complex but the designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module The modules build in SAM slot It could operate contact smart card according to ISO7816 The module and outside ant
4. enna are linked by 50ohm coaxial cable The impedance between RF module and antenna was tuned by impedance analyzer so it has excellent read write performance and stability Though the cable can reach 10m the performance is still good Normally the cable should be 60cm that is the module s best performance and stability 2 Characteristics PCD model Working frequency Supported standard Card supported NXP RC400 13 56MHz ISO15693 1507816 TI Tag It I Code SLI ST LRI and other tags according to 18015693 and ISO7816 SAM cards both T 0 amp T 1 Ant collision ability Full function anti collision be able to process multi cards be able to set operate single card only Auto detecting card SAM slot SAM baud rate ISO7816 PPSS set EEPROM Power supply Interface Communication rate Max command length Interface level Static power consumption Operating distance Dimension Weight ISP Operating temperature Storage temperature RoHS Supported default OFF The default status can be set 2 slot 9600bps 38400bps 19200bps default 115200bps 57600bps supported 512 Bytes DC 5V 0 5V UART RS232C USB select when place order UART RS232C USB 19 2Kbps 115 2Kbps 254 Bytes UART IIC 3 3V TTL level 5V tolerance 150mA 80mm depending on card 80mm 60mm 11mm About 70g Supported 25 to 85 C 40 to 125 C Compliant Copyright 2003 2014 Jinmuyu Electronics Co LT
Download Pdf Manuals
Related Search