TA Indoor - TA Service
Contents
1. Art nr 95162 TA Service A S Orupgade 32 B Orup DK 4640 Faxe Tlf 45 56 72 57 77 Fax 45 56 72 57 76 www ta service dk Warnings Read the instructions carefully It contains important warnings and instructions Do not reach into or under the chair when the seat lift and seat tilt 1s activated because there 1s a risk of entrapment between the mechanical parts Be aware of others especially children is too close to the chair when the seat lift and seat tilt is activated TA Indoor Wave is not intended for users with a weight exceeding 120 kg TA Indoor Wave should always be turned off when making entry and exit of the chair and when assisted by a helper so that the chair does not accidentally run if the joystick 1s activated The chair is EMC tested However it is possible that the wheelchair can be affected by electromagnetic fields from mobile phones for example Similarly it cannot be excluded that the chair can emit electromagnetic fields that can affect the surroundings such as alarm systems in stores Pay particular attention to late run when driving on ramps When the chair s brakes are disengaged the chair may roll if it is on a sloping surface Slowing down by pressing the On Off button there is a risk that the user s torso could fall over Ultimately the user could fall out of the chair This kind of slowdown should to the fullest extent be avoided on sloping surfaces and ramps By forcing level differ2. Maximum climbing ability over short distances theoretically 12 Maximum climbing ability over long distances 10 Maximum speed forward driving 6 km h Maximum speed revers driving 3 km h Clearance from floor 7cm Maximum level difference that can be forced Forward without run up 3 cm Forward with run up 4 cm Backwards without run up 4 cm Reverse with run up 5 cm Charger Specifications See user s guide included charger Aura 24V 5 A Penny and Giles R Net Drive Control Brakes Motor Brake and Electric Brake Motor brake acts as brake lock brakes and 1s activated when the control stick 1s released From you release the control stick and until the chair stands still there is a small late run on the chair This late run can be adjusted depending on whether you want a soft or a sharp slowdown It is possible to set how fast the chair s slowdown will be If this change is wanted please contact TA Service A S Electromagnetic brake is activated when the chair 1s stationary and serves as a parking brake Operating Instructions Before driving Footplate foot rests can usefully be looked up to facilitate the entry and exit Before you use TA Indoor Wave check the following The chair s speed is sufficiently low Any footrests are properly mounted and locked so they do not swing out while driving The seat lift is set at the lowest possible level and the seat tilt is as close to ho
3. The chair is fully charged 7 bar lights red and yellow The chair must be recharged as soon as possible 3 bar lights or blinks slowly red The chair must be recharged immediately in order not to destroy the batteries Speed Display Shows with graphs and numbers the current speed Tortoise shows that the chair is limited When the seat is lifted above 8 cm the seat can be tilted max 8 When the seat is tilted more than 8 the seat can max lift 8 cm By seat lift more than 8 cm or by seat tilt more than 8 reduces the chair speed automatic with 50 If the seat is not lifted higher than 8 cm the seat can be tilted fully 30 If the seat is not tilted more than 8 the seat can be lifted fully 30 cm Electrical functions Pressing the Mode button to get into the menu from which electrical functions can be operated with a joystick You select function by flipping the pages with the joystick and activate the feature by taking the control stick forward or backward Joystick activated If you activate the joystick before or just when you turn on the symbol will blink Release and center the joystick to use the chair If the joystick is not released and centered within 5 seconds the chair will not run even though the joystick is released Turn on and off the chair again to make it run Driving Profile The chair can be programmed for different driving profiles Contact TA Service A S for further instruction
4. ia id 13 oye aR a E S E E A 13 OO vato o PR e E E E E EE E E E 13 Ss A PE te II 14 ei OOK EATIO I o EIA e E E EE 15 AAA A o III 16 O E o yA 17 CIMA rot 17 TV UTQG Y esac ode carceane A E o II osneseaconeduseeacaeedeads 17 MA e E EE staat eanseennee 18 CAO OL COMO eee en epee tee eeepc anne 19 Technical Data Wheelchair Type Class A Wheelchairs mainly intended for indoor use and are not necessarily doing outdoor hurdles Dimensions Width excl seat 56 cm Length excl footplate foot supports 69 5 cm Length incl Standard footplate 88 5 cm Diagonal excl Standard footplate 90 cm Diagonal inc Standard footplate 105 5 cm Floor clearance measured engine part 7cm Space requirements at turning chair without Standard footplate 90 cm Seat lift 30 cm Seat tilt 34 about 3 to 31 Seat Mounting Height 40 cm The chair s weight with seat approx 102 kg depending on configuration User Weight Maximum user weight 120 kg Tires Solid tires front and rear Tire sizes rear 200 x 5 Tire sizes front 300 x 5 Temperature Storage Temperature 20 C to 50 C Operation Temperature 20 C to 50 C Batteries 2 pes 12V 35Ah Type gas tight lead acid Rekombinationsbattery Capacity 34 Ah Maximum charge current 5 Ah Battery Connection Type Bolt 5 mm Size e Width 13 cm e Length 19 5 cm e Height incl poles 17 cm Driving Data Maximum driving distance theoretical 15 km
5. within 5 seconds the chair will not run even though the joystick is released Power cycle the chair again to use the chair See lockdown joysticks to lock the joystick up CHARGER See enclosed instructions for charger 18 Declaration of Conformity CE Manufacturer TA Service A S Omarksgarden Orupgade 32 B DK 4640 Faxe E mail ta service ta service dk Product TA Indoor Wave elektric wheelchair ISO klassifikation ISO 12 21 27 Art nr 95162 The above aid is hereby declared to be designed and constructed in accordance with the essential requirements of Council Directive 93 42 EEC of 14 June 1993 See the Interior and Health Ministry Order No 409 on medical equipment of 27 May 2003 TA Indoor Wave is tested by Hj lpmedelinstitutet in Stockholm and complies with standard EN 12184 2002 TA Indoor Wave is EMC tested at Delta in Them in accordance with EN 12184 2009 and ISO 7176 21 2003 TA Indoor Wave is Climate tested at Delta in H rsholm according to ISO 7176 09 TA Indoor Wave is Crash tested by Dahl Engineering according to ISO 10542 5 amp 7176 19 2008 Faxe 2011 Torben Andersen Managing Director 19
6. and programming Locking Joystick The system can be locked using the joystick so the chair cannot drive and the system cannot be activated Locking the system When the chair is on press and hold the Power button 1 After 1 second the chair beeps release On Off 2 Press the joystick forward until a beep appears 3 Press the joystick back until a beep appears 4 Release the joystick there is now a long beep In case of lock this symbol appears in 5 The chair is now locked Symbol is shown in display display Locking up the system 1 If the chair is off turn on the chair 2 Press the joystick forward until a beep appears 3 Press the joystick back until a beep appears 4 Release the joystick there is now a long beep 5 The chair is now locked up the symbol disappears Setting Menu In the setting menu it is possible to change the clock brightness backlight and color and odometer To get into the options menu you must hold both buttons speed up and speed down simultaneously See arrow A Figure 1 The following points are then displayed in the menu Set time Adjust the time Press the control stick right to set the time Select exit at the bottom of the menu to come back Display time Selecting time format to display Features 12h 24h Off Backlight Backlight Features 0 to 100 in increments of 10 Background Background Here you can choose background color Set Time B
7. as reference In this manual you will find the information you need to operate the wheelchair If you have questions comments or suggestions please feel free to contact us TA Service A S Omarksgarden Orupgade 32 B DK 4640 Faxe Tel 45 56 72 57 77 Fax 45 56 72 57 76 ta service ta service dk TA Service A S makes continuous product development and we reserve the right to make changes CE TA Indoor Wave is tested by Hj lpmedelsinstitutet in Stockholm and complies with standard EN 12184 1999 TA Indoor Wave is EMC tested by the accredited test lab Delta following standards EN 12184 2002 and DS ISO 7176 21 2003 TA Indoor Wave is Climate tested by Delta in accordance to ISO 7176 09 TA Indoor Wave is Crash tested by Dahl Engineering in accordance to ISO 10542 5 amp 7176 19 2008 This handbook has been prepared in accordance with applicable requirements Contents A APP o Poo A 3 AA toe E EE EE E E E E E E ae 5 Operan tao Sa ose E A yeas E E E sneak suaetan eanseennauee 7 PHOS CV A119 rarr E o A 7 WII islas 7 PR CTI VAIN ala att aunt Neal N AnS 8 9 0110 DOR ata 8 ETS aia PO E 005 A PE E Terie mien free rrer E rere ener fe Serer Caner err ren 9 AAA PP N E E E RE E E E 10 Ac CLC CUS TUNCUONS UNC a sner A E 11 S AI E 1 AAA e Pi II A 12 SCN Up NC Si 0107 y eenean Geneon ce st E coe ENE eeaamis enn deseo EEE 12 Kaporin Wy Lie AVISO satan enla E 13 a PP e Ie 13 Mechanical disencacino the Drakes sensata o
8. e than 8 reduces chair speed automatic with 50 A of others especially children is too close to the chair when the seat lift and seat iltis activated Setting the armrests Armrest height in distance to the seat and armrest cushion distance to the back can be adjusted Armrest cushion position relative to the back is adjusted by loosening four screws A under the armrest with a slotted screwdriver Once the screws are loosened armrest cushion can be pushed forward backward and positioned to the user Armrest height is adjustable by loosening screws B on the armrest stanchion Setting up the legsupport The legsupport is mounted on the chairs seat frame Legsupport position relative to the seat is adjusted by loosening the two hex screws A 6 mm on the inside of the seat frame The legsupports can be adjusted to fit the user s femur length Legsupport length or the distance between the seating surface and base plate is adjusted by loosening the hex screw B 6 mm on the back of the legsupports down tube When the footrest is in the desired distance from the seat tighten hex screw again Footplate angle to the floor is adjusted by loosening the hex screw C 6 mm on the side of the footplate When the footplate is in the desired angle tighten the screw HARD Legsupport angle is adjusted by loosening the thumbscrew by hand set the legsupports in the desired position and tighten the screw Installat
9. ences it is important that the chair runs perpendicular to the obstacle in order to minimize the risk that the chair should tilt By forcing level differences with the seat tilted or hoisted there is a risk that the chair can tip over By forcing level differences it is therefore important that the seat is elevated as little as possible and is as close to an upright position as possible to minimize this risk Driving on slopes should be avoided because a slope to the site will give a risk that the chair can tip over When driving on slopes seat should not be lifted to keep the chair s stability Avoid touching leaky batteries as the contents can be harmful Repairs must be performed by TA Service A S or repairer who is authorized by TA Service A S Only original parts or parts that are approved by TA Service A S can be used Preface TA Services A S hope you are satisfied with your new TA Indoor Wave TA Indoor Wave is designed to facilitate your daily movement indoors and outdoors close to your home It has been very important to design the chair as small and compact as possible without reducing the chair s stability and handling Read the instructions carefully Tt contains important warnings and instructions Operating the wheelchair has been attempted designed simple but it is nevertheless important that you read through this manual so you re sure to get the most out of your TA Indoor Wave Keep this manual you can later use it
10. f the chair s stability by forcing different levels it is important that the seat is elevated as little as possible and is as close to an upright position as possible to minimize this risk Driving on slopes TA Indoor Wave can clear terrain rises up to 12 Driving on sloping surfaces should be carried out forward and at a slow pace 14 Transportation by car TA Indoor Wave is crash tested with 4 point car tiedown accessories and Dahl Docking System accessories so 1t can be used as a seat in the car bus or similar The user can use the TA Indoor Wave during transport by car bus or similar if the TA Indoor Wave is equipped with TA 4 point car tiedown and or Dahl Docking system If a belt is mounted on the wheelchair it will not replace the cars seat belt The cars seat belt must always be used 4 point car tiedown 4 attachment eyes are mounted on the wheelchair which can be used together with an approved 4 point car tiedown system These eyes are marked with a hook symbol se red arrows on the pictures V Contact TA Service for more information Dahl Docking System If Dahl Docking System should be used a plate is mounted in the bottom of the wheelchair which will lock into the docking system Contact TA Service for more information 15 Charging TA Indoor Wave is equipped with a battery level indicator at the top of the control box the long series of LEDs As the chair 1s used t
11. he battery level falls and the LEDs turn off See the following explanation Battery indicator All 10 bar lights Red yellow and green The chair is fully charged 7 bar lights red and yellow The chair must be recharged as soon as possible 3 bar lights or blinks slowly red The chair must be charged up immediately so not to destroy the batteries The charging plug from the charger A is connected to TA Indoor Wave in the front of the control box in the charger socket B The battery charger is switched on BOTH the 0 1 switch on the charger AND on the power point on the wall TA Indoor Wave should be turned off when batteries are charging RECOMMENDATION It s a good idea to put the chair for charging when not in use this will make sure that the batteries are always fully charged When charging is finished the charger automatically turns off There is thus no risk that the charger is connected to a charged battery RECOMMENDATION TA Services A S recommends that batteries be recycled PP Fuses Under the back shield in the left side is an overload protection Fig 1 Fuse cuts power if the wheelchairs maximum consumption exceeds 50A The fuse is a circuit breaker that switches off at overload To reconnected the fuse button is pressed which sits inside the shield arrow A Figure WA al Cleaning TA Indoor Waves shield can be cleaned with a cloth dampened in household detergent Do not use solvents
12. ion of the lap belt There can be fitted lap belt on the TA Indoor Wave TA Services A S recommends that the lap belt is fastened either by the back mount C or on a bracket in the chair seats C profile 12 Important when driving Braking The chair brakes by releasing the control stick so 1t returns to the vertical position It is possible to adjust how fast the chair 1s slowing down and thus reduce any late run on the chair This adjustment is carried out by TA Service A S At a short late run braking will be experienced very sharp Mechanical disengaging the brakes The electric brake can be disengaged by the need for manual towing This is done by twisting the brake handles away from TA Indoor Wave logo onto the wheels indoor When the electric brake is released the chair cannot be moved with the control stick This can only be done again when the brake handles is twisted back in vertical position away from the center and the electric brake 1s engaged again Emergency brake The chair can emergency brake by pressing the On Off button This brake method results in a very abrupt deceleration and should only be performed in an emergency and only 1f the user of the chair 1s prepared Force of obstacles TA Indoor Wave can climb obstacles up to 5 cm making it able to run over smaller doorsteps and the like At very steep increases may be necessary inlet and a certain speed In the interest o
13. lue blue light in all profiles White White background in all profiles The display is more visible with a white background in bright sunlight Auto The chair can be programmed to display different backgrounds at different profiles Contact TA Service for special adaptation Distance following submenu appears Total distance total distance power module has been running Total Distance 0012345 Trip distance Trip odometer can be reset Display distance option on the trip or total to be shown in display Clear Trip distance Resetting the trip odometer Exit Exit the menu 10 Setting the power functions The wheelchair may depending on model have the following power functions Seat lift Seat tilt Back Right legsupport Left legsupport The functions are activated by pressing the Mode button on the control box then there s a picture of power features Find the function to be used by flipping the pages of the control stick When the feature is found activate it by taking control stick forward or backward depending on which way the function should run Note When the seat is raised above 8 cm the seat can tilt max 8 If the seat 1s not lifted higher than 8 cm the seat can be tilted fully 30 When the seat is tilted more than 8 the seat can max be lifted 8 cm If the seat is not tilted more than 8 the seat can be lifted fully 30 cm By seat lift more than 8 cm or by seat tilt mor
14. on the shield Warranty There is 2 year warranty on TA Indoor Wave Valid from date of purchase Any warranty repairs will be performed free of charge with regard to working hours and spare parts The warranty period on batteries and tires supplied by TA Service A S is 1 year from purchase date If there is doubt about whether a particular battery charger can be used contact TA Services A S 17 Troubleshooting The chair cannot run 1 Charging connector is connected Remove the charging plug to the control box pF 2 Motor brake is disengaged Connect the motor brakes Po 8 Other cause Contact authorized service center The chair drives slowly Symbol appears in display Symbol appears in display 4 2C00 PM Low Battery 1 Speed Lower transferee is activated because of lifted and or tilted seat 1 The system has reduced power to the engines to prevent overheating 1 The system has generated an error and displays a text module and an error code 1 Joystick activated If you activate the joystick before or just when you turn on the symbol will blink 1 joystick is locked Lower the seat and or tilt the seat back to nearly horizontal Stop running and let the engines cool The engines were overloaded and exposed to more load than they are intended for Contact authorized service center Release and center joystick to use the chair If the joystick is not released and centered
15. rizontal neutral position as possible NB When the seat is raised above 8 cm the seat can tilt max 8 If the seat is not lifted higher than 8 cm the seat can be tilted fully 30 When the seat is tilted more than 8 the seat can max be lifted 8 cm If the seat is not tilted more than 8 the seat can be lifted fully 30 cm By seat lift more than 8 cm or by seat tilt over 8 reduces chair speed automatic with 50 The first drives in TA Indoor Wave should be conducted where there is plenty of room around the chair and the chair s speed should be low While driving TA Indoor Wave s driving characteristics including braking maximum speed and acceleration can be set to suit the individual needs Setting the chair s driving characteristics is performed by TA Services A S TA Indoor Wave is switched on by a light pressure on the Power button The chair s speed is increased by pressing the speed up button The chair s speed is decreased by pressing the speed down button After driving Always leave the chair off and put on lowest speed NB Leaving the chair turned on will draw power from batteries with reduced remaining driving distance to follow l 1 Power button 3 Display 4 Driving Profile 3 5 Speed up button 6 Switching between driving and menu 4 7 Speed down button 1 Battery indicator 2 Main Screen 3 Profile indicator Battery indicator All 10 bar lights red yellow and green
Download Pdf Manuals
Related Search