An Antenna Impedance Meter for the High Frequency
Contents
1. Figure 3 shows the input protection circuit of the AIM430 An isolation relay is open except when a measurement is in progress A gas discharge tube GDT protects the input against high voltage due to static charge on the antenna One of the op amp circuits is shown in Figure 4 There are two poles of high frequency attenuation including the R C filter at the out Current Sensor C9 4 Antenna J5 BNC U4 Voltage Sensor SA612AN 0 01 FRef amp _ 100 mV p p C14 QS0611 Clunno3 0 01 C17 0 01 3 75 V dc 100 mV p p Figure 3 Schematic of the voltage and current sensing circuits Two mixers are used to convert the load current and load voltage to the audio range typically 1 kHz put of the mixer A third pole is provided by a sample hold circuit later in the analog signal processing chain The frequency response of the signal path peaks at 1 kHz and is 60 dB down at 100 kHz The op amps provide filter ing and also convert the differential signal to a single ended signal for input to the analog to digital converter ADC Since the desired sig nal is always 1 kHz we do not have to worry about variations in the amplitude and phase response of the low pass filters Identical mixer and amplifier circuits are used for both the voltage and current sensing paths Any small differences in the gain and phase shift of these two paths are taken care of by the calibration process which will be dis2. be in the range of 0 to 1 SWR 1 U 1 U Note the SWR only depends on the mag nitude of p so it is not a complex number If p is zero no reflection the SWR is 1 0 1 Since a term 1 U appears in the denominator the SWR can be very large when the trans mission line is badly matched to the antenna and the magnitude of the reflection coeffi cient U is almost equal to one Applications The analyzer s test conditions are speci fied by entries on the PC These include scan start stop frequencies frequency increment between data points and display scale factors There is also a provision to enter the nominal transmission line impedance so the SWR can be calculated for any value After the scan is complete the mouse can be used to move a cursor along the frequency scale to display the numeric values of several parameters including SWR impedance magnitude and phase equivalent series circuit and equivalent parallel circuit The full scale ranges for measurements are e SWR up to 100 1 e Impedance magnitude 1 Q to 10 KQ e Phase angle 90 to 90 e Frequency scan 500 kHz to 32 MHz Figure 5 shows the scan of a piece of RG 58 coax that is open at the far end The coax is 28 feet long The frequencies at which the phase angle crosses the axis are called reso nant frequencies and are listed across the top of the graph In this case the first frequency corresponds to the 1 4 A of the coax The sec ond
3. crete components and tuned circuits R5232 I O Figure 12 There are two PC boards sandwiched together with 0 1x0 1 inch connectors The top board contains all the RF circuitry and the bottom board has the microprocessor and electronic power switch The 3 3 V regulator is mounted on the rear panel that acts as a heat sink 3 3V REGULATOR ON OFF SWITCH Acknowledgments I would like to thank Dave Russell W2DMR Danny Richardson KOMHE and Paul Collins ZL3PTP for evaluating the AIM and providing suggestions that greatly enhanced the program Thanks also to Bill Cantwell WBS5SLX and Forest Cummings WS5LQU for their proof reading and encouragement Notes J Hallas W1ZR Product Review A Look at Some High End Antenna Analyzers QST May 2005 pp 65 69 2Direct digital synthesizers theory of operation www analog com library analogDialogue archives 38 08 dds pdf 3AIM430 User Manual and demonstration pro gram w5big home comcast net antenna _analyzer htm Data sheet for AD9851 DDS w5dbig home comcast net AD9851 pdf Data sheet for SA612 mixer w5big home comcast net SA612 pdf 6Data sheet for MSP430F149 micropro cessor focus ti com docs prod folders print msp430f149 html Schematic and printed circuit board design software www expresspcb com Bob Clunn W5BIG received his Novice license in 1956 while in junior high and his general license soon after Dur
4. value is the frequency Because of loss in the cable the maximum impedance at the 2 frequency 11 681 MHz is only about 1200 Q at the input end of the coax not infinity At the frequency corresponding to a 1 23 467 MHz the impedance is about 800 Q because of increased loss at the higher frequency The 1 and A frequencies are not exactly in a 2 1 ratio because the velocity of propagation varies slightly with frequency Notice the way in which the phase angle violet trace changes rapidly at 5 765 and 17 532 MHz even though the magnitude of the impedance is changing slowly Finding the phase angle zero crossing makes the loca tion of the 4 A frequencies more accurate than relying on the magnitude of the imped ance The cursor is the light colored vertical line at 11 697 MHz and the data displayed Antenna Analyzer AIM430 File Data Setup Help Min SWR 3 134 17 100 MHz SWR Resonant freq 5 798 11 621 17 431 Antenne Arneabycer AMAA Fie Dyo Setup Help Zmag 0622 05 16 18 31 Scan Rescan Recvele Limits Scales Cable Smith Commenti Halt Quit Figure 7 Scan of 28 feet of RG 58 coax with a 243 resistor termination in the window on the right side of Figure 5 corresponds to this frequency R and X are the series circuit values Rp and X are the parallel circuit values Figure 6 shows a Smith chart of the data from the scan in Figure 5 The small dot at about the 1 o clo
5. volt age amplitude divided by the current ampli tude The phase angle of the impedance is the difference in the phase angles of the voltage and current Knowing these two parameters we can calculate the equivalent resistance and reactance of the load impedance R Resistance Impedance_Magnitude x cosine phase_angle X Reactance Impedance_Magnitude x sine phase_angle The external load resistance is found by subtracting the internal 100 6 series resis tance R21 R22 shown in Figure 3 from the calculated resistance The equivalent series circuit is Z R JX where j is the square root of 1 The equivalent parallel circuit is also calculated and displayed in the data window as the cursor moves along the frequency axis Resistance is always a positive number Reactance can be positive or negative Positive JSF November 2006 29 reactance is associated with inductance and negative reactance with capacitance The true sign of the phase angle is determined by the data processing routine so capacitive reac tance and inductive reactance can be distin guished without ambiguity As can be seen from the scan pictures the phase changes rap idly as it passes through zero Critical points in the plot such as maximum or minimum impedances can be located more accurately on the frequency axis using phase rather than by looking only at the impedance magnitude Standing Wave Ratio SWR is probably the antenna s most i
6. An Antenna impedance Meter for the High Frequency Bands When SWR isn t enough here s a tool that you can build Bob Clunn W5BIG SWR meter is a very useful instrument and in many situa An tions provides all the informa tion needed to check an antenna However an impedance meter provides a much more detailed picture of the antenna parameters There are several such instruments on the market with prices in the range to appeal to hams These typically have broadband inputs and use diode detectors The broad band input is subject to incorrect reading due to strong signals such as broadcast radio sta tions even when the frequencies of these sig nals are a long way from the test frequency The diode detectors are subject to nonlinear ity error at low signal levels so their dynamic range may be limited Design Goal My goal was to design an instrument for accurately measuring impedance with magnitude and phase so that all the desired parameters of an antenna can be deter mined and displayed in a graphical format The resulting antenna impedance meter AIM430 measures RF voltage and current and uses these values to calculate complex impedance and other parameters of inter est The AIM430 provides a detailed look at the antenna system Formulas in the design books become more meaningful when you can quickly see how the real and imaginary parts of the impedance vary with frequency The AIM430 continuously co
7. ard to see the difference between them on the graph There is only a small difference in the two phase angle traces shown in violet Interference Rejection The band pass circuits in the AIM430 help to reject interfering signals that are more than about 100 kHz from the desired test frequency Figure 10 shows the result with and without an interfering signal that has an amplitude of 63 dB over S 9 The distur bance of the reading is confined to an interval of about 100 kHz Additional Applications In addition to measuring antennas the AIM430 can be used to measure discrete components such as resistors capacitors and inductors It is particularly interesting to see how the component value varies as a function of frequency Inductors with metal cores are often very frequency sensitive It can also be used for adjusting tuned circuits such as traps and for measuring the parameters of quartz crystals and other resonator devices The output signal from the analyzer can be used as a test signal for checking receiv 32 November 2006 Q54 RELAY T Tr cs IN ISOLATION ali CL abet ts INPUT Ef Y MIXERS ers The output into a 50 Q load is about 35 MV ms The amplitude is not precisely cali brated but the variation over any of the ham bands is less than 0 5 dB The frequency can be set in 1 Hz increments and it can be cali brated against WWV Calibration The AIM430 is calibrated by measuring the resi
8. can of Figure 7 configuration referred to antenna cable loss increases with frequency Reference Transformation Sometimes it is desirable to know the impedance directly at the antenna terminals After a calibration phase during which the properties length and loss of the cable are determined at each measurement frequency measurements made at the transmitter end of the line can be transformed to the antenna terminals This is done in real time during the scan and the displayed data is very close to what would be measured if the analyzer were actually mounted at the antenna The calibration is done by disconnecting the far end of the transmission line from the antenna and then scanning the cable input impedance with two different resistive termi nations One terminating resistor is typically in the range of 20 to 100 Q and the other can be in the range of 1 KQ to 2 KQ The resis tor values are not critical as long as they are accurately measured with a digital ohmme ter When the transmission line calibration is performed the exact resistor values are entered in the program via dialog boxes The terminating resistors can be low power film devices since they don t have to handle the transmitter power After the cable calibration is finished the data are saved to disk so they can be recalled anytime later Using the Impedance Transformation Feature Figure 7 shows a conventional scan with the 243 Q resistor at the end of 28 f
9. ck position is a marker that Antena Analycer AMAU Fig Cate Soiup Help bin SWR 77 680 13 500 MH Hel to Antonina Resonant freq 14 906 Circuit at the end of the coax Circuit connected directly to analyzer 6 72 05 Fa Scan Rescan Recvele Limits Scales A L C circuit at analyeer and then at the end of 40 feet of coax Cable Smith Commenti Xs Theta wT 100 s 400 100 E225 tAr Scan Rescan Re terminals moves along the Smith chart as the cursor moves along the frequency axis In this pic ture the cursor is at 9 515 MHz The equiva lent series and parallel circuit values are shown on the Smith chart along with the real and imaginary parts of the reflection coef ficient The trace spirals inward because the Figure 9 Two scans of a series L C tuned circuit termination The first is with the circuit connected directly to the AIM430 the second is referenced to the end of the coax In the ideal case they would be identical 14 00 FREQ MHz B Figure 10 Scans with and without interfering signal At A a scan without interference The SWR reading red trace is 3 1 in this example At B a scan with a CW interference level of 63 dB over S 9 injected directly into the input Min DWR 5 351 12 500 Biz SWR Resonant frog 3460 3 969 4 019 5 109 5 24 Ref to Antenna 17 00 FREQ 1 00 Miz div Figure 8 S
10. cussed later After the RF signals are converted to the audio range it is much easier to measure their amplitude and phase This is done by digitizing the two signals with a 12 bit ADC that is contained in the Texas Instruments MSP430F149 microprocessor This micropro cessor runs at 7 MHz and the ADC samples are precisely timed by its internal clock Both the current and the voltage channels are sam pled with 16 samples per cycle The raw data is sent to a PC through the RS232 serial port an RS232 USB converter can also be used The PC calculates the impedance and all the other desired param eters The PC then graphically displays a detailed view of the parameters as the fre quency range is scanned The software has been used with Windows 95 98 2000 and XP There is no definite speed requirement although faster is bet ter because the program is computation ally intensive I ve run it successfully on a 300 MHz laptop using Windows 95 The program doesn t require an installation pro cedure just click on the exe file and it runs It can be copied to a hard drive or run directly from a floppy or a CD Data Analysis The two sets of digital data from the volt age and current sensors are analyzed using the discrete Fourier transform This produces the amplitude and phase of the 1 kHz fundamental signal and cancels out any dc component due to offsets in the operational amplifiers The magnitude of the load impedance is the
11. dual capacitance and inductance in its output circuit The phase shift and amplitude differences in the voltage and current amplifi ers are also measured This calibration data is then used to compensate each reading Stray capacitance and inductance associated with an external test fixture if used are also taken into account by this procedure Calibration is performed by using a short circuit and an open circuit First a short cir cuit is connected to the analyzer and several measurements are taken Then the short is removed and the open circuit properties are measured This data is saved in a file that is automatically loaded each time the program is run The whole calibration process takes only a few seconds Since the analyzer does not have any internal adjustments no pots or trim caps the calibration is very stable It only needs to be done when the external test fixture or cable adapter is changed Construction The microprocessor is initially pro grammed through a 14 pin JTAG interface Subsequently the program can be updated through the standard RS 232 interface Conclusions The operation of an affordable vector impedance meter for measuring antennas in the high frequency range has been presented Using state of the art components for signal generation and analysis the AIM430 provides a high level of accuracy and wide dynamic range for complex impedance measurements The unit is also quite useful for measuring dis
12. eet of RG 58 coax The green trace is the magnitude of the measured impedance As expected the value varies over a wide range as a func tion of frequency At the frequency 11 621 MHz the indicated impedance is close to 243 because the same impedance is seen at both ends of a half wave line Now we click SETUP and REF TO ANTENNA The legend REF TO ANTENNA is js November 2006 31 Figure 11 The enclosure is 5x5x2 inches which leaves room inside for an optional battery pack The dc current required is about 150 mA while taking a measurement and 30 mA if idle After 10 minutes of inactivity the dc power is turned off automatically Two LEDs on the front panel indicate POWER ON green and TEST IN PROGRESS red displayed in red at the top of the graph while this feature is enabled The resistor 243 Q and the cable are the same as used in the previous graph The Zmag plot shown in green is relatively flat across the frequency range The measured resistance now varies only from 243 to 248 Q a range of 2 The phase angle and the reactive component are nearly zero Figure 9 shows that the transformation also works quite well with a complex load circuit A series L C tuned circuit was used for the load For the first scan it was con nected directly to the BNC connector on the AIM430 Then it was rescanned with the load at the end of 28 feet of coax The impedance and reactance curves almost coincide it s h
13. ing high school he was very active on 40 and 20 meter CW During this time he made the decision to study electrical engineering in college Bob received his BS degree in electrical engi neering from Rice University in 1965 and his MS from Southern Methodist University in 1969 He was employed at Texas Instruments in Dallas from 1963 until 1991 His work there involved the design of computer controlled test equipment for transistors and integrated circuits From 199 to the present he has been working as a consul tant for several companies in the fields of elec tronic circuit design and machine vision In 2002 Bob renewed his interest in ham radio and obtained his Amateur Extra class license Soon afterward he got interested in equipment to evaluate antennas and began the design of this antenna analyzer He can be reached at 509 Carleton Dr Richardson TX 75081 or at w5big comcast net OS
14. is case 120 32 or 88 MHz Therefore to get good attenuation at 88 MHz and beyond the DDS low pass filter cutoff is set at 45 MHz The filter attenuation is greater than 60 dB above 88 MHz After the DDS output is filtered it is used directly to provide the stimulus signal for the QS0611 Clunn01 DDS AD9851 impedance measurement There is no buffer amplifier This eliminates the harmonic dis tortion of an amplifier and keeps the output signal amplitude low to reduce the interfer ence to nearby radio receivers The maximum output power is less than 50 uW The output amplitude of the DDS goes down slightly as the frequency goes up The variation over the entire operating range of the analyzer is only about 3 dB This is no problem since we are using the ratio of two RF signals to calculate impedance and the amplitude of the stimulus cancels out in this ratio To calculate impedance we need two values voltage and current Both the magni tude and the phase are measured These two parameters are sensed using 1 resistors There are no transformers in the AIM430 The voltage across one resistor 1s proportional to the voltage being applied to the circuit under test and the voltage across another resistor is proportional to the current flowing into the circuit connected to the analyzer s test port The ratio of these two voltages cor responds to the impedance we want to mea sure Figure 2 sho
15. nteresting parameter This is calculated by first determining a parameter called reflec tion coefficient When a signal travels down a transmission line with a characteristic imped ance of Zp and arrives at the antenna with a different impedance some of the signal is reflected back toward the transmitter This reflection occurs even if the transmission line is of the highest quality and the antenna is a perfect radiator The reflection coefficient is the fraction of the voltage that is reflected Antonin fob AKAJO Fia f rps Gaby rti Bate Min GAR Hiit 1300 Miir 5 Resonaed treg 564 a Tenet mik el ee FREO 1 00 MHE dh DA Dea ACAD Opon eireuit 78 inet lang lel Limits Antenna Analyzer AIM430 File Data Setup Help Min SWR 14 462 17 300 MHz SWR Resonant freq 5 765 11 681 17 532 23 467 10 15 00 EQ 1 00 MHz di Zo 50 0 at the antenna back toward the transmitter Its magnitude is also equal to the square root of the ratio of reflected power to inci dent power If there is no reflection 1 e the reflection coefficient is zero then all the power from the transmitter is absorbed by the antenna which is usually the desired case If the transmission line is open at the antenna perhaps due to a broken wire all the power arriving at the break point is reflected back toward the transmitter none is radiated so the reflection coefficient has its maximum value of unity If the transmi
16. ssion line is open the reflection coefficient is plus one if the line is shorted the reflection coefficient is minus one Reflection_coefficient p ZL Zo ZL Zo where Z Impedance of the load Zo Impedance of the transmission line Z is a complex number therefore p is in general a complex number with a magnitude between 0 and 1 and a phase angle in the range 90 Since the reactive component of Zo is lol x imag AVG OM r oo Freg 11 697 Zo 50 SWR 242505 Fmacy 1202971 Thel 5 597 Rell Coel 0 321 Return Loss 072 db Figure 5 Scan of 28 foot unterminated coax shartgpen Circuit Cable Loss 036 db Eguw algni Arcu Rs 1197245 xg 117 230 s 116 067 pF Rp 1208 774 Ap 1234 450 Cp 1 102 pF Scales Gable Smith Gommentl_ Halt Gut Smith Chart Freq 9 515 07 29 05 09 42 12 RG58 Open circuit 2 Scan Rescan Recvecle Limits Scales Ce Rs Real Gamma Imag Gamma 6 920 Xs 79 389 0 397 0 835 Rp 917 656 Xp 79 992 Figure 6 Smith chart of 28 foot unterminated coax 30 November 2006 JSF usually very small it is often ignored and Zo is considered to be a real number such as 50 Q or 75 Q The value of Zo can be entered from the program s main menu so the SWR can be calculated for any value of transmission line impedance For the SWR calculation let U equal the magnitude of p U will
17. vers the frequency range of 500 kHz to 32 MHz and operates in conjunction with a PC which allows easy control through a graphical user interface It can also be battery powered and connected to a laptop computer for com pletely portable operation Basic Operation The AIM430 uses two frequency sources that are heterodyned to produce a low fre quency signal in the audio range that can be easily amplified filtered and analyzed The Notes appear on page 32 28 November 2006 Q54 required frequencies are generated by two AD9851 direct digital synthesizer DDS inte grated circuits made by Analog Devices One DDS operates at the specified test frequency and the other is programmed to operate 1 kHz above it These are both driven by a crystal controlled oscillator running at 20 MHz The DDS chips internally multiply this clock by a factor of six so the effective clock rate seen by the DDS is 120 MHz In general the DDS can be used to produce an output up to about one third of its clock frequency A block diagram of the AIM430 is shown in Figure 1 The output of each DDS is followed by a low pass filter with a cutoff frequency of 45 MHz These filters remove the spurious high frequency components that appear in the out put The DDS generates many frequency com ponents in addition to the one that is desired For example if the DDS is programmed for 32 MHz there is a strong signal at the clock fre quency minus 32 MHz in th
18. ws the voltage and current waveforms In Figure 3 there are two mixers one for 0 5 32 MHz Antenna Digital CPU MSP430 Figure 1 Block diagram of AIM430 antenna analyzer Reprinted with permission copyright ARRL Zload V I ma Voltage applied to a load m Current flowing into the load 8 Phase angle between V and QS0611 Clunn02 Figure 2 Voltage and current waveforms with complex load Reference SIGA R57 TLV23721DR 10k QS0611 Clunn04 Figure 4 One of the two 1 kHz differential amplifiers and band pass filters sensing the current flowing into the load and the other for sensing the voltage applied to the load FDRV is the programmed test signal from one of the DDSs This is the stimulus signal for the load under test FREF is the out put of the other DDS which is 1 kHz higher in frequency than FDRV This second DDS is the local oscillator The SA612 has dif ferential inputs which make it very handy to directly measure the voltage across a current sensing resistor Therefore we don t have to use transformer coupling The output impedance of the SA612 is about 1500 Q A 0 01 uF capacitor to ground filters out the high frequency component the sum of the input and local oscillator leaving the kHz difference signal The differential outputs of the mixers are connected to op amps through dc blocking capacitors These capacitors also provide attenuation at low frequencies
Download Pdf Manuals
Related Search