Pressure Fit 3 Post User Guide
Contents
1. Before you start Check Requirements and Cautions continued Cautions A Failure to observe cautions listed below could result in serious injury or death Cautions Before installation e The pressure fit system parts should not be loose broken or bend If any part is missing or damaged do not install Contact your local authorized dealer immediately e The Pressure Fit System must be assembled prior to use Should you have any questions during assembly contact your local authorised dealer e Never installed the Bottom foot plate on the top portion of post section or vice versa See section Assembly instructions e Ensure rubber feet are cleaned and dry prior to each use See section General Inspection and mainte nance e Do not install The pressure Fit System to suspended ceiling e Do not install The pressure Fit System on a plaster ceiling e Do not install on a sloped floor greater than 5 degree e Ensure floor area is clear off dirt and debris e Never expose the Pressure Fit directly to water Warranty does not cover any misuse or abuse of the Pres sure Fit system e Any accessories used with the Pressure Fit System including lift and sling s should be checked to ensure that they are in good working order Check for signs of wear or fraying prior to use Report any unusual wear or damage immediately to your local authorised dealer e Ensure that a clear space is maintained around the Pressure Fit S2. Min 1 2 Joist Span should be max 24 FLOOR REQUIREMENTS e Ensure Floor area is cleaned and free of dirt amp debris e Floor should meet the requirements of building code standards e Floor must not have a slope of more than 5 degree See table below to determine the slope of floor FLOOR FLOOR ONE END X OTHER END yr SLOPE OF FLOOR X 6 FEET 7 FEET 8 FEET 9 FEET 10 FEET DISTANCE BETWEEN FLOOR ENDS Y 630 195 837 942 1 047 MAXIMUM SLOPE OF FLOOR AT SPECIFIED DISTANCE 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 7 Read Requirements and cautions before installing the 3 Post Pressure Fit System 1 Examine the room where you plan to install the 3 Post Pressure Fit System Make sure the room meets all the speci fications outlined in Ceiling and Floor Requirements 2 Use the measurements mentioned in the figure below to determine the best spot to place 3 Post Pressure Fit System MIN 7 Feet M MAX 10 Feet T a Peles WIDE 20 Feet MIN 7 Feet MAX 9 Feet HEIGHT Figure 1 3 Install the Pressure Fit system approx 36 40 away 4 Allow 36 1000 mm of open area for transfer from the head of bed or wall of the Room Figure 2 working space Figure 3 36 40 be 99 Away from S wall or i a head board Bed Figure 2 Figure 3 3 Post Pressure Fit System User Guide Rev 2lst September 2011 Page 8
3. damaged Track connector hooks are not sitting right on the post pins Ratchet is not held during disassem bly Lever arm is not engaged with mag net Red button is not pressed in enough Physical damage to safety lock cover Lock latch Spring breaks Top post spacer damaged Bottom post plug damaged Bottom plate foot post damaged or bend Top plate foot post damaged or bend Rivets are broken or loose Rev 2Ist September 2011 Do not use the system Contact your local authorized dealer immedi ately Check Mounting adjustable Track Assem bly instructions in the user s manual Check visually to ensure track connector hooks are sitting at the same height If problem persists contact local authorized dealer immediately Follow Post Disassembly instructions to dismantle the post Follow Post Disassembly instructions to dismantle the post Press in the Red button all the way so that safety lock can be engaged Contact local authorized dealer immediately Contact local authorized dealer immedi ately Contact local authorized dealer immediately to continue the proper functioning of Pressure Fit System Do not use the system Contact your local authorized dealer immedi ately Page 32 General Inspection and Maintenance Failure to follow inspection and maintenance instructions below as instructed may result in serious injury or death Periodic general inspection
4. Adjustment Track is placed in the correct location for transferring The portable lift has been inspected as outlined in it s owners manual The sling s has been inspected as outlined in it s owners manual B Cleaning Rubber Feet Instructions Prior to each use the Top and Bottom rubber feet need to cleaned with wet cloth soaked with water Step 1 Take the Bottom rubber foot and wipe off the dirt with a wet cloth as shown in picture Step 2 Take the Top rubber foot and wipe off the dirt with wet cloth as shown in the picture Note After cleaning Make sure the rubber feet are clean and dry with no residue of dirt or dust left on them Also ensure Floor area is cleaned and free of dirt amp debris 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 34 Service Record History Initial Information Complete the following section Purchase and Service Information as soon as this equipment is installed Use the service record history to record any completed service and repairs Ensure that the service record is signed and dated each time it 1s used Be sure to have this piece of equipment serviced on a regular basis as described in the General Inspection and Maintenance Section PURCHASE INFORMATION Product Name 3 Post Pressure Fit System _ Serial Date of Purchase Date Installed Purchased From Address City Post Code Telephone No Comments SERVICE INFORMATION Conta
5. is dry and free of debris If problem persists contact your local authorized dealer immediately Press in the Ratchet and hold it Grab the lever and push up to the magnet label Contact local authorized dealer immediately Ensure lever is cleaned and free of grease or dirt If problem persists contact your local authorized dealer immediately Set up the post following post assembly In structions Tight the barrel nut with Flat Screw Driver Contact local authorized dealer immediately Check for physical damage to track If so contact local authorized dealer immediately Clean the track slots with cloth and wipe out the dirt or debris Again try extending the tracks If problem persists contact your local authorized dealer immediately 1 visually make sure tracks and wheels are fine and are free of obstacles 2 Ensure that tracks are cleaned with cloth and free of dirt If problem persists contact local authorized dealer immediately Page 31 The adjustable track is not locking on the Post Pins Misalignment of adjustable track on the Post Pins for Example track is not sitting straight on the post as sembly Post cannot retract Safety Lock Not working Difficult to insert top and bottom foot into Post assembly Track Connector Bracket are loose 3 Post Pressure Fit System User Guide One or more track connector Bracket s are damaged or broken Track lock pin s is are broken or
6. Cleaning Rubber Feet Instructions Should anything look unusual contact your local dealer prior to use Failure to comply with this caution could result in serious injury to the operator the in dividual being lifted and or damage to the Pressure Fit and or portable lift unit Assemkiing the Support Posts Step 2 Tilt the supporting post to the side to facilitate the installation of the top foot Insert the top plate through the top opening of the supporting post Placed the bottom foot on the floor Insert the bottom plate through the opening located at the bottom of the supporting post NOTE Never install Bottom Foot at the Top section of Post Never install Top Foot at the Bottom section of Post 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 11 Assembly Assembling the Support Posts Continued Step 3a Step 3b Press the red button down to release Safety Lock Released the safety lock Note Pushing down the Post will help in pulling out the lever Step 4a Step 4b While pushing with two hands the Grab and Push down on the top section l Cr lever will move out as shown in picture of post with two hands as shown in Picture 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 12 Assembly Assembling the Support Posts Continued Step 5a Step 5b Press in and hold the Ratchet Push the lever up to engage with the while pulling out the lev
7. If not contact dealer for replacement e Record the service record history form for any completed service and repairs e Ensure that the service record is signed and dated each time it is used Follow the general inspection and maintenance instructions for portable lift as mentioned in it s manual FAILURE TO COMPLY WITH THIS MAY RESULT IN INJURY TO THE INDIVIDUAL BEING LIFTED AND OR THE CAREGIVER OR DAMAGE TO THE LIFT AND OR THE PRESSURE FIT SYSTEM 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 33 General Inspection and Maintenance A Each Use To be completed by User Prior to each use the 3 Post Pressure Fit System and associated lift accessories and sling s must be visu ally inspected Refer to the lift accessory and sling user guides for specific details regarding their inspection Should any of the these items below fail the inspection do not use the Pressure Fit System Contact your local authorised dealer for service Visually check for the following The 3 post pressure fit system parts should not be loose broken or bend Ensure ceiling area is rigid and without cracks dust grease and any slippery substance The Bases are on a stable level surface and the Side Support Assemblies are secure The Trolley moves easily along the track The Top and Bottom Foot must be cleaned with wet cloth before installation in order to remove dirt on rubber moulds see cleaning rubber feet The
8. PRISM MEDICAL 3 Post Tw iE Pressure Fit System Owner s Manual Use and Care Trouble Shooting Warranty Information Table of Contents 3 Post Pressure Fit System SCI OCGUGC COIN eisai eee E TTE ETT E T EEPE TTET EAT 3 Overview of the 3 Post Pressure Fit System 0 3 Placement of the 3 Post Pressure Fit System 4 Components of 3 Post Pressure Fit System 5 Gomponent IST pp 6 Specifications of the 3 Post Pressure Fit System 6 Requirements and Cautions rrrrrrarrnnrrarrnrrrarrarrnnrrarrnnnnarnnnnnr 7 Assembly Assembling the Support Posts rrarorrrrarrnrrrarrnnerennnrr 11 Mounting the Adjustable Track rrorrrarrarrnrrrarvnrrnarnnnnnr 16 Assembly 3rd POSt u nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnunnnnnnnn 18 Assembly 3rd post and Middle tracK nnnnnnnnnnnnnnnnnnnnnnnnun 19 Completed Pressure Fit System 21 Final Inspection Prior to Use rmrrrarrarrarrarrarrnrrarrnnrnnnner 23 Mounting the Portable Lift 24 Disassembly Middle track Disassembly nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnuuun 25 Track Disassembly Instructions rrarrrarrarrrrrarrnrrrarnnrr 26 Support Post Disassembly Instructions 27 Trouble Shooting arrarerrrrarrnrerarrarrnerrarrnnrrarrnnnnernannnnnnannannnennnsnnn 29 General inspect
9. Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 2Ist September 2011 Page 36 Service Record History Service Type o Periodic Inspection oc Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken 3 Post Pressure Fit System User Guide Complete this section after each service repair inspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Si
10. and maintenance should be performed by a person who is properly qualified and trained with the use and care of The Pressure Fit System Any defects and damage to the Pressure Fit System that have lead to corrective actions should be noted and dated by the inspector The defects and corrective actions report should be submitted in written form to the dealer Upon Receipt of The pressure Fit system e Ensure all the received components are according to the component list e Ensure the user manual is present other wise do not install the pressure fit system e Ensure all the components are in working condition and not damaged e Ensure service record history forms are included in the package to record any completed service and re pairs e Complete the Purchase and Service Information as soon as this equipment is installed Periodic maintenance e Ensure all the components of Pressure Fit System are in working condition If damaged please contact the dealer for replacement before use e Inspect all the joints and components for wear and fatigue If the parts are damaged then contact dealer for replacement of parts e Clean the rubber feet according to Cleaning Rubber Feet Instructions e Check rubber feet for damages If damage is noticed please contact dealer for replacement e Check the Track and trolley for dirt and debris It should be cleaned with cloth during every use e Ensure the labels are legible and in good condition
11. cations of the Pressure Fit System e High strength lightweight Aluminum e Portable or semi permanent installation e Eliminates the mounting of a connection system in the ceiling e Pressure gauge indicator to help ensure proper installation e Quick attachment with secure fixings e Addresses a number of different bedroom amp bathroom situations e Weight capacity 440 lbs e Adjustable in length e Built in easy slide trolley e Exerting pressure between Floor and Ceiling is 80 to 100 Ibs e Specially designed and engineered rubber molded feet for ultimate grip e Leveling indicators on posts e One 1 year warranty Minimum Maximum Dimensions Model Table for the Pressure System l Se lt i 341502 3 Post Pressure Fit System 3 Post Pressure Fit System User Guide Rev 2lst September 2011 Page 6 Before you start Check Requirements and Cautions Requirements A Failure to meet the requirements listed below could result in serious injury or death CEILING REQUIREMENTS e Install the Pressure fit system to a rigid ceiling structure e Ceiling structure must have joists that are spanned maximum up to 24 between the trusses e Ceiling made of wood must be at least 12 7mm 1 2 thickness e Ensure the ceiling structure is not suspended by wires or rods e Ensure ceiling should be clear of any cracks grease water or any other slippery substance Joist framework Above ceiling Ceiling Thickness
12. ct the following company for service Company Address City Post Code Telephone No Comments 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 35 Service Record History Service Type o Periodic Inspection oc Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken 3 Post Pressure Fit System User Guide Complete this section after each service repair inspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o
13. e finger into the Ring from underneath Ring should be pulled down all the way and the track and pull the Ring all the way down slide the track slightly until the pin is under the trolley and Release the Ring 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 22 Assembly 3rd post and Middle adjustable track Keep sliding the track E amp GE ee i EE Step 20 Step 21 Slide the track through the trolley Slide the track until the pin is out as shown in figure F ET nn Fae gt 7 7 cl Completed Assembly 3 Post Pressure Fit System 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 23 Assembly 3rd post and Middle adjustable track Note Make sure track goes Note Make sure track goes all the way to the end all the way to the end Step 22 Step 23 Grab the middle track and slide the track to one Repeat the same step for the other end also end as shown in figure Make sure track goes all the way to the end Note While moving the middle track there will be some resistance Slightly push to go all the way Track end is away from wall Note There must be enough room to move the middle track smoothly See requirements page 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 24 Final Inspection Prior to Use JANGER RESSURE REQ DICATOR IN RED Ensure Pressure Gauge 1s in the Safe Zone SAFE N
14. elephone 905 850 0093 Fax 905 850 8377 Toll Free 1 800 265 0677 This document conforms to EN ISO 10535 requirements TM Trade mark of Corven Health Care Inc Used under licence Printed in Canada E amp O E 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 39
15. em User Guide Rev 2lst September 2011 Page 15 Mounting the Adjustable Track A Caution Before installing the adjustable track ensure lifting height is sufficient to lift the patient See Below different heights adjustment for all versions of Pressure Fit System Note You need a Step Ladder to do this assembly Ask for assistance if you require help in installing the tracks Failure to comply with this caution could result in serious injury to the operator the individual being lifted and or damage to the Pressure Fit and or portable lift unit Traverse Track Bottom Pin gt Working Heights for all versions of Pressure Fit System are as follow 1 For 341500 2 Post Pressure Fit System All 3 Hook Pins of both Post assemblies can be used for the Adjustable Track to adjust the lifting height 2 For 341505 3 Post Pressure Fit System Only Top and Middle pin of Ist and 2nd Post Assembly can be used for the Adjustable Track to adjust the lifting height while Middle and bottom pin of 3rd Post Assembly can be used to hook the Traverse Pivoting track 3 For 341510 4 Post Pressure Fit System All 3 Hook Pins of all 4 Post Assemblies can be used for the Adjustable Track to adjust the lifting height A Note Drop in height per Hook pin is 6 360 3 Post Pressure Fit System User Guide Rev 2lst September 2011 Page 16 Mounting the Adjustable Track Caution Before installing the adj
16. er magnet NOTE SEE MAGNET LABEL Step 6 Step 7 Push the top section of post up towards the ceiling Swing open post level Please ensure the with Top foot Upon contact with the ceiling con level is fully open tinue pushing up until you hear one or two more clicks Note At this point the post should be exerting pressure between the floor and ceiling 3 Post Pressure Fit System User Guide Rev 2lst September 2011 Page 13 Assembly Assembling the Support Posts Continued Step 8a Step 8b Grasp bottom section of post lift slightly and Bubble centered adjust until bubble is centered and post is perpendicular to floor and ceiling Step Ya Step 9b Push the lever down until it clicks into place Push the lever in to secure it until you hear a click sound Note Lever must rest in vertical position 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 14 Assembly Assembling the Support Posts Continued SAFE PTABLE PRESS SSS gt CATOR IS IN GRE Step 10 Step la Ensure Pressure Gauge is in the Safe Zone Swing back the safety lock and level to the original Note Green must be visible on both sides position Step 12 Install the second post repeating steps 1 though 11 Note The distance between the two posts should be between 7 to 10 feet Step 1 1b Safety Lock and Level must be firmly Engaged in housing 3 Post Pressure Fit Syst
17. essure Fit System User Guide Rev 2Ist September 2011 Page 26 Middle Track Disassembly Instructions Note You need a Step ladder to do this disassembly Ask for assistance if you require help in disassem bly the tracks A Warning Failure to read and follow these instructions carefully may result in serious Injury Ask for assistance if needed Step 1 Step 2 Slide the track till pin hits the trolley Pull the ring and hold it and Slide the track Slightly till the pin goes under the trolley Release the Ring Step 3 Slide the Track through the Trolley Hold the track Step 5 Step 6 Unhook the Track from Pin position Store the removed adjustable track in a safe place 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 27 Track Disassembly Instructions A Warning Failure to read and follow these instructions carefully may result in serious Injury Note You need a Step ladder to do this disassembly Ask for assistance if you require help in disassem bly the tracks Step 2a To Unhook the track assembly lift the track up from one post end Step 1 Remove the end caps from both posts Step 2b Squeeze the track and unhook from the other post Step 2c end Store the removed adjustable track in a safe place 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 28 Supporting Post Disassembly Instructions A Warning Failure to read and follow
18. gnature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 2Ist September 2011 Page 37 Service Record History Service Type o Periodic Inspection oc Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken 3 Post Pressure Fit System User Guide Complete this section after each service repair inspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection
19. ion and maintenance merraronnrnannnnrnannnnn 31 Service record history cece cece cece cece eeeeeeeseeeseeeseeeaes 33 Warranty or ee eo eee 37 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 2 CAUTION DO NOT ATTEMPT TO USE THIS EQUIPMENT WITHOUT FIRST UNDERSTANDING THE CONTENTS OF THIS MANUAL Introduction Before using this equipment and to ensure the safe operation of your Pressure Fit System carefully read this entire manual especially the section on Requirements amp Cautions The Pressure Fit System is designed to be used in conjunction with Prism Medical Ltd portable lift units accessories and slings Please refer to any user guides supplied with these components and reference them while reviewing this manual Should any questions arise from reviewing this manual contact your local authorised Prism Medical dealer Failure to comply with warnings in this manual may result in injury to the operator or the individual being lifted transferred Damage to the lift and or related components may occur Be sure that the contents of this manual are completely understood prior to using this piece of equipment Store this manual with the documents included with the lift system and sling s Contents of this manual are subject to change without prior written notice Overview of the 3 Post Pressure Fit System The Pressure Fit System is a lifting aid used by health care profes
20. lation Lever is not engaged with magnet Pressure gauge is not in safe zone The Adjustable Track does not ex tend smoothly or doesn t extend up to required limit Trolley does not move smoothly along the adjustable track 3 Post Pressure Fit System User Guide Level is not working Floor is not leveled Level is damaged Post was knocked with impact Feet are not cleaned Floor is not cleaned Post Assembly instructions not fol lowed Clutch bearing function fails Lever not cleaned Post assembly instructions not fol lowed Barrel nut is loose or not secured tightly Top plate Spring broken or bend Physical damage to track Track slots are not cleaned Physical damage to track or trolley wheels Track slots or trolley wheels are not cleaned Rev 2Ist September 2011 1 Set up the post following Post Assembly instructions Check visually and with master level to ensure the post is aligned straight Note Never unlock the post with the track connected Check the floor with master level for flat ness Visually check the level is fine Dismantle the post following Post Disas sembly Instructions and set up the Post again following Post assembly instruct tions Note Never unlock the post with the track connected If problem persists contact your local authorized dealer immediately 1 Clean the feet as per Cleaning Rubber Feet Instructions 2 Ensure floor area
21. o Repair o Yearly Inspection o Other Signature Rev 2Ist September 2011 Page 38 Warranty This Warranty does not affect or in any way limit your Statutory Rights 1 Subject to the exclusions set out in Clause 2 the conditions set out in Clause 3 and the limitations set out in Clause 4 Waverley Glen Systems Ltd as sole licensed representative of Corven Healthcare Inc guarantees all equipment supplied as new against failure within the period of 1 year from date of purchase by virtue of defects in material or workmanship 2 This guarantee does not apply to failure attributable to normal wear and tear damage by natural forces user neglect or misuse or to deliberate destruction or to batteries more than 90 days after original purchase 3 This guarantee shall be void if the equipment is not serviced by Prism Medical Ltd or its authorised service agents in accordance with the manufacturer s recommendations or if any unauthorised person carries out works on the equipment 4 The liability of Prism Medical Ltd under the terms of this guarantee shall be limited to the replacement of defective parts and in no event shall Prism Medical Ltd incur liability for any consequential or unforeseeable losses If you have any questions about the manufacture or operation of this equipment please contact Prism Medical Ltd or your local authorised dealer PRISM MEDICAL Prism Medical Ltd 87 Sharer Road Vaughan ON L4L 8Z3 Canada T
22. ost 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 19 Assembly 3rd post Step 16 Install the 3rd post with 3 pin holes repeating steps 1 though 11 Use the 3rd foot with white Plastic washer to install the 3rd post Note The distance between the 3rd post and other 2 posts should be 7 to 8 feet Foot with plastic washer on it oi Te a et A Y i wae Art R A Nae AA g re eke 4 Pr f N i Te e 1 ME Mg Qn Cee ere pe Mu th s l i d ya wie a ae D JERN gt Be ioe 4 ee F f ot Mocks E Wan Rice d J i y na an i E vr i F E d gt i 4 p i 7 A BE li d f i f ar i 3 Post Pressure Fit System User Guide Rev 2lst September 2011 Page 20 Assembly 3rd post and Middle adjustable track Note You need a Step Ladder to do this assembly AN Ask for assistance if you require help in installing the middle track One hook on the Middle adjustable track Step 17 Take Middle adjustable track with one hook Middle P 4 E gt ar dA E 3 MA A p lt a Step 19a Hook the track to the middle pin of the 3rd Post Grab the other end of the track and slide into the trolley 3 Post Pressure Fit System User Guide Rev 2lst September 2011 Page 21 Assembly 3rd post and Middle adjustable track Pin Hits the trolley Pull Ring Down With Finger Step 19c Step 19d Put th
23. ote Green must be visible TABLE PRESS on both sides Safety Lock and Level must be firmly Engaged in housing End covers are installed properly 3 Post Pressure Fit System User Guide Rev 2lst September 2011 Page 25 Mounting the Portable Lift Figure 1A FULLY ASSEMBLED PRESSURE FIT SYSTEM Prior to mounting the portable lift onto the trolley of the Pressure Fit System please read the owners manual of the portable lift Be sure that the instructions on the use of the lift and any accessories such as slings are thoroughly understood before attempting to use them with the Pressure Fit System FAILURE TO COMPLY WITH THIS MAY RESULT IN INJURY TO THE INDIVIDUAL BEING LIFTED AND OR THE CAREGIVER OR DAMAGE TO THE LIFT AND OR THE PRESSURE FIT SYSTEM Following the instructions for the portable lift attach the carabiner or other similar attaching device Note Portable reacher arm doesn t work located at the end of the lift strap to the hole of the Pressure Fit trolley Be sure that the carabiner is securely attached to the trolley prior to proceeding with the transfer FAILURE TO COMPLY WITH THIS MAY RESULT IN INJURY TO THE INDIVIDUAL BEING LIFTED AND OR THE CAREGIVER OR DAMAGE TO THE LIFT AND OR THE PRESSURE FIT SYSTEM Proceed to transfer the individual in the manner described in the owners manual for the portable lift and sling When the transfer is completed the lift may be removed from the trolley 3 Post Pr
24. sionals and those providing care in the home to lift position and transfer clients or a disabled family member The Pressure Fit System is part of what is termed overhead lift technology which takes advantage of lifting from above and not from below or the side The Pressure Fit System makes it possible to move mobility impaired individuals with minimal strain or risk to the caregiver while providing complete safety dignity and comfort for the client or family member The Pressure Fit System is designed to work with a Prism Medical portable lift system such as the P 440 Use of other portable lift units with this system may be possible but not P 600 because capacity of pressure fit system is 440 Ibs However please contact your local authorised Prism Medical Ltd dealers in or der to obtain approval before use The Pressure Fit System can be used to lift and transfer individuals from a bed chair or similar fixture The length is adjustable and thus can be assembled to suit a wide range of applications The Pressure Fit System is easy to assemble and can be completed by just one person in a short period of time Additionally no tools are required It is also light in weight and once dismantled can be moved to another location such as a hotel or cot tage Please review the following pages that outline the parts included with your package Should you have any questions about this product or its use contact your local authorized dealer 3 Post Pre
25. ssure Fit System User Guide Rev 2Ist September 2011 Page 3 Placement of the 3 Post Pressure Fit System in a Room MIN 6 FEET MAX 8 FEET i SWIVEL a TROLLEY ADJUSTABLE LIFT TROLLEY TRACK z SIDE SUPPORT P ASSEMBLY 1 MIN 7 FEET MAX 9 FEET HEIGHT Figure 1 A shows 3 post pressure fit system set up in a room In this drawing arrangement a gen eral placement of a bed is shown in relationship to the Pressure Fit System Notice that there is still room for a wheelchair to be placed beside the bed The view shows min and max height and width of the pressure fit system for which it can be set up DO NOT USE THE SYSTEM OUTSIDE OF THIS RANGE OF PLACEMENT OTHERWISE A SERIOUS INJURY MAY OCCUR TO THE OPERATOR OF THE LIFT AND OR THE INDI VIDUAL BEING TRANSFERRED AND OR THE PRESSURE FIT SYSTEM 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 4 Components of the 3 Post Pressure Fit System Si sn Swivel Trolley Track gt 4 Lift Trolley Supporting Post Sections Figure 1B DISASSEMBLED 3 POST PRESSURE FIT SYSTEM 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 5 Component List The following components are included with your new Pressure Fit System Description Quantity Bottom Foot Top Foot Supporting Post Swivel Trolley Lift Trolley Owners Manual Warranty Card eo Adjustable Track Specifi
26. these instructions carefully may result in serious Injury Keep Holding the Lever Step 3 Press the red button to release the Step 4 safety lock Press the lever in all the way to release the pressure from the ratchet NOTE Lever May Swing Out Always keep one hand on the lever Step 5 Step 6 While pressing in the lever push and hold While holding the ratchet pull out the the ratchet lever 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 29 Supporting Post Disassembly Instructions Step 7a Push the lever up to engage with magnet Push in and hold the ratchet while pushing the top section of post down Step 7d Bring back the lever to vertical posi tion Step 7c Make sure the bottom pin touches the plastic cover Step 9 Take off top and bottom Foot Store the components in a safe place Step 8 Bring back the level and safety lock to Repeat steps 3 to 9 for the other 2 original position Posts disassembly 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 30 Trouble Shooting Should problems arise with the use of the Pressure Fit System review the following chart Find the fault and complete the recommended solution If the fault is not found and or the solution does not correct the problem contact your local authorized dealer for service immediately Visually the system is not aligned straight Feet are slipping after instal
27. use neglect or pur poseful destruction of the lift and or its associated components e Under no circumstance should the track lift and sling s or entire system be put in control of a person who has not been properly trained in the use and care of this equipment Failure to adhere to this warning may result in serious injury to the operator and or the individual being lifted transferred e In places where more than one operator will be responsible for using the Pressure Fit associated lift and sling s it is imperative that all operators be trained in its proper use e The Pressure Fit System and associated lift and sling s are not toys Do not use them for unsafe practices Do not allow children to play with the this equipment or any of its components e To maintain optimum function the Pressure Fit should be inspected and maintained on a regular basis See the section titled General Inspection and Maintenance e The manufacturer s warranty is void if persons unauthorized by Prism Medical ltd perform work on the Pressure Fit System 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 10 Assembly Caution Before using the Pressure Fit System the top plate bottom plate support ing posts and adjustable track must be visually checked to ensure that there are no missing parts or unusual wear and tear Top plate and Bottom plate should be cleaned and dried with wet cloth before installation See
28. ustable track ensure lifting height is sufficient to lift the patient See Below different heights adjustment for all versions of Pressure Fit System Note You need a Step Ladder to do this assembly Ask for assistance if you require help in installing the tracks Failure to comply with this caution could result in serious injury to the operator the individual being lifted and or damage to the Pressure Fit and or portable lift unit MIN 7 Feet MAX 10 Feet WIDE MIN 7 Feet MAX 9 Feet HEIGHT 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 17 Mounting the Adjustable Track with swivel trolley Note You need a Step Ladder to do this assembly Ask for assistance if you require help in installing the tracks Step 13a Hook one end of the track to post pin Note Ensure track connector is sitting properly on the spring pin as shown above Step 14a Attach the track end cap as shown above 3 Post Pressure Fit System User Guide Step 13b Extend the track and hook to the other post Note Don t leave the track connector on the spring pin as shown above Step 14b Install the other end cap Rev 21st September 2011 Page 18 Completed Adjustable Track with swivel trolley aa Note Mount the adjustable track on the top pin only of the Post Measure 8 feet from the Post Use measuring tape Step 15 Measure 7 8 feet from post to set up 3rd p
29. ystem Remove all furniture and other obstacles out of the way before performing a transfer 3 Post Pressure Fit System User Guide Rev 2Ist September 2011 Page 9 Before you start Check Requirements and Cautions continued Cautions After Installation e Ensure that the pressure gauge is in the safe zone during set up e Ensure Posts are level both visually and with the built in level If unsure use a master level to verify the straightness of the Posts e Make sure track is sitting properly on the posts e Make sure trolley is sliding smoothly on the track e Make sure safety lock button and level are locked e Make sure the end stop for swivel trolley is working properly e Never unlock the Post when Track is attached e Do not under any circumstance exceed the maximum load rating for this piece of equipment Refer to the Specifications section of this manual Do not use P 600 lift e The installation of the Pressure Fit System lift accessories and sling are certified to a maximum load Do not exceed the maximum rated load of any of the components e The Pressure Fit System has been designed to lift vertically at its maximum load and at its maximum height Do not attempt to lift an individual at an angle to the track e The Pressure Fit System and associated lift and sling s are intended only for lifting and transferring of a person Prism Medical Itd will not be responsible for any damage caused by the mis
Download Pdf Manuals
Related Search