SUMMARY OF SYSTEM COMMANDS
Contents
1. AWAY Arming Stay Enter code 3 STAY all zones designated as zone types 4 and 10 will be automatically bypassed Arming Instant Enter code 7 INSTANT same as STAY without entry delay Arming Maximum Enter code 4 MAXIMUM same as AWAY without entry delay Disarming Enter code 1 OFF Bypassing Zones Enter code 6 BYPASS zone number To automatically bypass all faulted zones use Quick Bypass method Enter code BYPASS Chime Mode Enter code 9 CHIME To turn chime mode off enter code CHIME again 161 162 Quick Arming Note that if QUICK ARM is enabled field 29 the key can be pressed instead of entering the security code for any of the arming procedures Away Stay Instant Maximum etc aa User 02 must be programmed into the system in order for the Quick Arm feature to work Global Arming SUMMARY OF ARMING MODES Features For Each Arming Mode Mode tf Entry Perimeter Interior Delay Delay Armed Armed MAXIMUM ys e e Yes If enabled for the user the keypad will display the following ARMALL 10 NO 1 YES If NO the keypad prompts for arming each partition individually If YES the system attempts to arm all partitions allowed by this user If there are any faults open doors windows etc the keypad will display them See notes below These faults must be corrected or2. by 1 or 2 hours This is useful if a user must stay on the premises later than usual The user must have authority level of manager or higher To extend the closing window enter user code 82 Closing Delay Enter the number hours 1 or 2 by which the end of the Hit 0 2 Hours closing window should be extended Note that the delay is from the scheduled closing time not from the current time Press to accept entry and exit this mode Press to exit this mode without changes The system will send an Access Schedule Change message to the central station when the closing window is extended if programmed in fields 2 13 and 2 14 K An extension of the closing window cannot be reduced once it is set However a 1 hour delay can be increased to 2 hours This is to prevent the user from deleting the delay after the normal window expires thereby missing the end of the window Partition GOTO Commands Each keypad is assigned a default partition for display purposes and will show only that partition s information To see information for another partition or perform system functions in another partition use the GOTO command code partition number 0 8 The keypad will remain in the new partition until directed to go to another partition or until 120 seconds has elapsed with no keypad activity To return to your home partition enter partition number 0 2h You must progra
3. SUMMARY OF SYSTEM COMMANDS Event Logging Commands Alpha keypad only Wireless System Commands User Code Commands Alpha keypad only Arming Functions Alpha keypad only Alpha keypad only Alpha keypad only Programming Commands Scheduling Commands Alpha keypad only Output Device Control Alpha keypad only Event Log Display Code 60 Event Log Print Code 61 Installer Only Clear Event Log Code 62 Installer Only House Id Sniffer Mode Code 2 Installer Only Transmitter Id Test Code 3 Installer Only Go No Go Test Code 5 Test Key Add A User Code User Code 8 New User Number New User s Code Change A Code User Code 8 User Number New User s Code Delete A User s Code Your User Code 8 User Number To Be Deleted Your Code Again View User Capability User s Code Set Real Time Clock Installer Master Only Code 63 Arming Away Enter Code Away 2 Arming Stay Enter Code Stay 3 Arming Instant Enter Code Instant 7 Arming Maximum Enter Code Maximum 4 Quick Arm Use Key Instead Of User Code Followed By Any Of The Above Arming Mode Keys Global Arming If Enabled For The User The Keypad Will Display A Prompt Answer The Prompted Questions Disarming Enter Code Off 1 Bypassing Zones Enter Code Bypass 6 Zone Number To Automatically Bypass All Faulted Zones Use Quick Bypass Quick Bypass Method Enter C
4. ay Activation mode General Information The keypad allows the user to arm and disarm the system and perform other system functions such as bypassing zones viewing messages from the central station and displaying zone descriptors Zone and system conditions alarm trouble bypass are shown in the display window When an alarm occurs keypad sounding and external sounding will occur and the zone s in alarm will be displayed on the keypad Pressing any key will silence the keypad sounder for 10 seconds Disarming the system will silence both keypad and external sounders When the system is disarmed any zones that were in an alarm condition during the armed period will be displayed memory of alarm To clear this display simply repeat the disarm sequence enter the security code and press the OFF key The keypads also feature chime annunciation and 3 panic keys for silent audible fire or personal emergency alarms which can notify the central station of an alarm condition if that service is connected Arming Functions The following is a brief list of system commands For detailed information concerning system functions refer to the User s Manual Display Faulted Before arming the system must be in the READY Zones condition all zones must be intact If the NOT READY message appears press the READY key to display faulted zones Arming Away Enter code 2
5. es Users may occasionally receive a message from their installation company displayed on an alpha keypad When this occurs the keypad will display Message Press 0 for 5 secs Instruct the user to press and hold the 0 key to display the central station s message Note that the system must be in the READY state to view these messages Using The Built In User s Manual Panic Keys An abbreviated User s Manual is stored in the system s memory and can be particularly useful to the end user if the printed User s Manual is not conveniently accessible when the user needs to perform a seldom used and unfamiliar system procedure The Built in User s Guide is displayed only on an alpha keypad by simply pressing any of the function keys e g OFF AWAY STAY MAXIMUM BYPASS INSTANT CODE TEST READY and CHIME for approximately 5 seconds and then releasing it Abbreviated instructions relative to the key that has been pressed will then be displayed 2 lines of text are displayed at a time This function operates in either the armed or the disarmed state There are three panic key pairs shown below that if programmed can be used to manually initiate alarms and send a report to the central station Each key pair can be individually programmed for 24 Hour Silent Audible or Auxiliary Emergency responses as well as Fire The panic function is activated when the appropriate key pair is pressed at the same time The panic functions are ident
6. ified by the system as follows PANIC Displayed as Zone 14 95 For alpha keypads these panic keys can also be programmed with an alpha 13 96 descriptor 99 2h For the Panic functions to be of practical value the system must be connected to a central station Speed Key D Macros The D key can be used to activate a string of up to 16 keystrokes These keystrokes are known as a macro and are stored in the system s memory Each partition may have its own macro Typical Speed Key functions include e Arming sequences that involve first bypassing certain zones before arming Seldom used but repeatable sequences e Relay activation sequences To program a macro enter your user code D The following appears ENTER SPEEDKEY D existing sequence displayed Enter up to 16 keystrokes A speed key sequence can include different commands Press the D key to separate different commands For example you may want to perform the following sequence Desired function Keystrokes GOTO partition 2 Enter 2 Bypass zones 10 amp 11 Press bypass 6 then the zone numbers 10 amp 11 Arm in maximum mode Press maximum 4 key Return to partition 1 Enter 1 To program that speed key sequence type the following 2 D 61011 D 4 D 1 D D Note that the D key is pressed after the 2 the last 1 and the 4 separating the different command
7. m data field 2 18 to enable the GOTO function This is a partition specific field that must be set for each partition the user wants to access from another partition s keypad Viewing Capabilities Of A User The keypad will display the partitions that a user is authorized for the user number and the authority level for all partitions authorized Enter code The user s capabilities in each authorized partition will typically be displayed as follows Part 1 AO WHSE The user s Open Close report capability is shown by the User 01 Auth 1G dot following the authority level If Open Close is not enabled for a user the dot will not appear Viewing Zone Descriptors The Alpha Keypads can display all programmed descriptors which is useful to the installer when checking entries and can be helpful to the user when there is a need to identify zones To display descriptors the system must be disarmed and ready to arm Press and hold the READY key until the built in instructions for that key appear then release the key The zone descriptors will appear one at a time for about 2 3 seconds each For faster viewing press the READY key to display the next descriptor in numerical order and so on When all descriptors have been displayed the control will exit display mode To exit display mode before all descriptors have been displayed enter the security code and press the OFF key 163 164 Viewing Downloaded Messag
8. ode Bypass Chime Mode Enter Code Chime 9 To Turn Chime Mode Off Enter Code Chime Again Partition Goto User Code Partition Number 0 8 GOTO Home Partition User Code 0 Panics 1 Zone 95 A Key Zone 99 B Key 4 3 Zone 96 C Key View Downloaded Messages Press 0 For 5 Seconds Display All Zone Descriptors Press For 5 Seconds Display User Self Help Hold Any Key For 5 Seconds Site Initiated Download User Code 1 Direct Wire Download Enable User Code 5 Enter Program Mode Installer Code 800 Exit Program Mode 99 Or 98 Installer Programmed Schedule Events Installer Code 80 Temporary Schedule Editing User Code 81 Installer Master Manager Only Extend Closing Window User Code 82 Installer Master Manager Only End User Output Device Programming User Code 83 Activate Output Device As Programmed User Code 71 Activate Output Device As Programmed User Code 72 Activate Access Relay For Current Partition User Code 0 Activate Output Device Manually User Code 70 177 Section 25 KEYPAD FUNCTIONS This section provides the following information e General information about keypad usage Basic keypad functions Global arming Access control Delaying closing time Executing the Go To command Viewing A user s capabilities Zone descriptors Downloaded messages Built in user s guide e Speed key macro commands e Executing 70 Manual Rel
9. riptor DEVICE nn ON OFF FOR HIT O OFF 1 ON voice descriptor ON ENTER 1 FOR voice descriptor OFF ENTER 0 Press 0 or 1 to turn the device off or on respectively nn represents the 2 digit relay X 10 module number and voice descriptor is the relay voice descriptor programmed by the installer see relay descriptor programming section nn DEVICE IS OFF Voice voice descriptor DEVICE nn ON OFF TO EXIT HIT THE KEY ENTER 00 NOW From a keypad press to continue The ENTER DEVICE NO prompt will appear From a telephone keypad enter 00 to exit or enter the next relay number to be programmed The current on off state of that relay will be annunciated as described above Alternatively if 6 seconds elapses with no key depression the voice module will annunciate the ENTER DEVICE CODE NOW message 165
10. s Press D twice to complete the entry and exit To execute a speed key sequence press the D key The following appears ENTER USER CODE Enter your user code The programmed speedkey sequence will begin automatically When defining speedkey sequences do not use the key to represent Quick ae Arming The system uses the code entered in response to the prompt to initiate commands in a speedkey sequence so the quick arm key is unnecessary The system interprets the use of the key in a spoeedkey sequence as its designated function only e g 2 is not interpreted as arm in away mode but rather as enter house ID sniffer mode Manual Relay Activation Mode 70 Mode The system allows users to manually activate relays X 10 modules by keypad command using either the keypad or a telephone keypad if VIP module is used The user will be prompted either by keypad alpha display or telephone voice module To activate relays from a keypad enter 4 digit security code 70 To activate relays using a telephone and VIP module first dial the 2 digit phone access code When the system acknowledges the access enter 4 digit security code 70 The following prompts voice responses will begin ENTER DEVICE NO Voice ENTER DEVICE CODE NOW 00 QUIT 01 Enter the 2 digit number of the relay X 10 module to be activated nn DEVICE IS OFF Voice voice desc
11. the zone bypassed before arming will occur When faults are corrected repeat the arming procedure 1 When using the Global Arm feature if there are faults in any of the selected partitions the system will enter a summary mode in which the faulted zones of all of the selected partitions will be displayed These faults must be corrected or bypassed code BYPASS will attempt to bypass the faults in all of the selected partitions This summary mode will end in approx 120 seconds if no keys are pressed If when disarming the system using a Global Disarm any of the selected partitions has a condition which would cause the keypad to beep such as alarm memory or a trouble condition the system will cause the keypad to beep and will enter a summary mode in which the alarm memory or trouble conditions of all of the selected partitions will be displayed This mode will continue until either approx 120 seconds elapses or a second disarm occurs which clears the beeping whl keypad Global arming cannot be performed from a wireless keypad or a non alpha E Access Control If programmed one relay may be used for access control in each partition The relay is programmed in data field 1 76 To activate this relay the user enters his user code o The relay will pulse for 2 seconds Delaying Closing Time If Open Close schedules are used end users can manually delay closing time by extending the closing window
Download Pdf Manuals
Related Search