Wall Mounting Bracket
Contents
1. a5 N Use the anchors for wall material of concrete light concrete strong natural stone soft natural stone masonry 0 brick and hallow block that do not crack Z I Check the material of the wall and the thickness of the finishing When installing the product on the wooden wall refer to page 6 When installing the product on wall material not designated install the product so that each fixated location can withstand the pull out load of 7Okgf 686N and shear load of 1Okgf 980N or above Anchor 0 6 Co WADA uu Wall mount screw 0 Emre earns a Use the 8mm drill bit for concrete and hammer Impact drill a Use a drill bit 8mm to drill a hole for the anchor location within a depth of 80mm 100mm b Clean the drilled hole c Insert the sealed anchor to the hole When inserting the anchor use a hammer d Set the wall mount on the wall by aligning to the location of the hole and set the angle adjusting part to face upward e Align the wall mount bolt to the hole and tighten it At this time the bolt must be tightened with torque of 45kgf cm or above How to install the wall mount lt When installing on a masonry wall gt When you separate the 4 screws on the wall mount connected to the wall bracket for use with a wooden wall it is much easier to install the product f Wall mount Se2. gt Product specification 15 15 2 H Unit mm 15 15 2 lt With the bracket removed gt lt With the bracket attached gt Model Name LSW100B LSW100BG Model Name LSW100B LSW100BG Width mm 221 Width mm 435 Height mm 152 Height mm 167 Depth mm 14 Depth mm 20 Weight kg 09 Weight kg W Wall Mount VESA Specification 100 X 100 200 X 100 Wall Mount VESA Specification 100 X 100 200 X 100 Max UL Load Capacity kg 15 Max UL Load Capacity kg 15 ENGLISH LG Life s Good The model and serial number of the Supported Displays product is located on the back or one 19 22 26 32LD side of the product Record it below 19 22 26 32LE should you ever need service 19 22 26 32LX 19 22 26 32Lk MODEL 19 22 26 32LZ 19 22 26 32LW SERIAL 19 22 26 32LV
3. LG Life s Good OWNER S MANUAL Wall Mounting Bracket Please read this manual carefully before operating your set and retain it for future reference LSW100B LSWI1OOBG P NO MFL63640503 1101 REVO3 www lg com 1 Year Warranty the product and effective only in the local area If material or workmanship proves defective under normal use during the warranty period please contact the retailer where you purchased it This warranty is good only to the original purchaser of lt e Component Wallmount anchor Wall mount screw User manual 4 units 8 units oo I PVC Washer Set protection cushion Set screw 4 units 4 units M4 X 10mm 4 units M4 X 14mm 4 units Due to the shallow clearance between the display and the wall the LSW100B Wall Mounts may require the use of the included angled adapters lt Component cable with angled connectors gt lt HDMI angle adapter gt 23 Note that the included angle adapters may block other connections on the back of the TV Make sure the connectors on the cables connected to the display do not press against the wall a IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Warning This wall mount should be installed by a trained and experienced installer designated by the retailer Having the product installed by a non specialized installer is very dangerous a
4. an the drilled hole f Tighten the wall mount screws for the wall bracket on the drilled hole At this time tighten the screw so that the wall wall bracket and the wall mount screw are pressed against one another Drywall can be damaged when tightened with excessive force please be careful When tightening the screw use the driver Manual or motorized or 8mm wrench How to assemble the wall mount support and display Always install the display with 2 or more people After mounting the display insert the safety pin as shown If the safety pin is not fixated as shown in the picture the display can fall After the install is finished pull the bottom part of the display to verify the product is attached securely gt In using cables or accessories not provided with the wall mount make sure to keep a certain distance from the wall so that excessive force is not applied on cables or accessories mn How to level the Display _ Cable arrangement and set protection cushion Arrange the cables as shown in the picture Use some type of cable banding device to hold all the cables together Attach the set protection cushion to mitigate the impact between the wall and the set when adjusting the angle Attach the set protection cushion as shown in the picture If the product is not leveled after the installation you can rotate the display up to 5 degrees
5. ig 1 separate the safety pin from the wall mount as shown in Fig 2 2 Separate the set bracket as shown in Fig 3 Attaching the mounting bracket on the TV Make sure the screws are fully tightened to the bracket and display If the screws will not fully tightened they might be too long or the wrong size VESA 100X100 VESA 200X100 is supported If needed you may refer to the display s user manual to verify the display has one of the supported VESA formats Screws are included for the following models F O M4 X 10mm H A Bracket to attach to 19 22LD 19 22LE 19 22LX 19 22LK 19 22LZ a WN the display 19 22LW 19 22LV 26LE65 T Rn M4 X 14mm pe 26 32LD 26 32LE Excludes 26LE65 26 32LX 26 32LK 26 32LZ 26 32LW 26 32LV VESA 200 Install the PVC washer between the brackets and the display on the following models 32LE53 32LE55 But for 26LE53 26LE55 model this is provided as TV component VESA 100 VESA 100 lt Work procedure gt 1 Check to see if the display has screws already installed into the VESA mounting holes If so remove those 2 Attach the bracket to the back of the display as shown above Use a Phillips head screwdriver to tighten the screws At this time be careful to prevent the set from falling down Make sure the screws are fully tightened to the bracket and display How to attach to masonry walls
6. nd can cause damage or injury Use a trained and experienced installer to move or replace the wall mount if needed Installation requires special techniques and moving or installing the product on your own can cause serious safety issues When installing the wall mount never hang the power or signal cable on the rear side the TV The cord can be damaged and cause a fire an electric shock or damage to the product 2 Do not install the product where the weight cannot be supported If the strength of the location where the wall mount is installed is not strong enough it can fall off and cause an injury After installing the wall mount do not hang on the product or apply severe impact to the product The product can fall off and cause injury Caution Install the product according to the directions in the user manual If the product is not installed based on the directions in the user manual it can cause a serious injury or damage to the product During the installation check the type of wall material and use the sealed anchor and screw if the conditions comply If you do not use the designated anchor or screw the mount may not be able to withstand the weight of the product and cause a safety issue Do not wipe the product with a wet towel and do not use any heater or humidifier below where the product is installed If water flows into the product or if moisture and heat are applied to the product it can cau
7. oduct and contact the dealer to have a specialized installer install the product for you Even if you are not a specialized installer it is advantageous to have experience in mechanical or construction field in completely understanding this manual and installing the product This product is designed to be mounted to walls that use standard intervals between the studs Install the screw to attach the wall mount so that it can be assembled at the center from both ends of the studs Use of stud finder a separate device is recommended Install the product only on a vertical wall The manufacturer is not responsible for issue from installing the product on severely wall or on the ceiling Keep the included accessories out of reach of babies or children as it can cause safety issues including suffocation from swallowing the parts Make sure screws are tight against the wall but do not overtighten Be careful not to install a TV that exceeds the weight restrictions of the wall mount Be careful with the tools used during installation to prevent accidents or damage ENGLISH a Installation method Tools you will need Phillips head driver Manual or motorized 4mm drill bit for wood or steel Level Stud finder Drill You may also need an 8mm socket wrench or an 8mm drill bit for concrete Separating the TV bracket lt Work procedure gt 1 After expanding the wall mount forward as shown in F
8. parate the wall mount screw f the screw cannot be assembled in the designated location inevitably it can be assembled by rearranging to the closest location But do not change 2 or more locations from the designated spot Assemble the wall mount screw on 1 left and 1 right location on the top part and 1 left and 1 right location on the bottom part At this time use a driver Manual or motorized or 8mm wrench to tighten the screw so that the wall wall bracket and Use a level to check whether the wall mount is level screw are completely pressed against one another gt When installing the product on a masonry wall turn the 4 screws on the A part counterclockwise to separate the screw and bracket After aligning the wall bracket to the location to install mark the part to screw on the wall and then remove the wall bracket Refer to page 4 to attach the wall bracket lt When mounting to wooden studs gt Temm drywall 2 wood stud drywall a Locate and mark the centers of the wall studs using a stud finder b After aligning the wall bracket on the wall where the center of the wood stud is marked mark the location of the screws and then remove the wall bracket c Use a level to make sure your screw marks are level d Use the 4mm drill bit for wood to drill holes with the depth of 76mm or above where the wall mount screw location is marked on the wall e Cle
9. se a fire an electric shock or problem to the product Unplug the power cord from the power outlet before installing the product If you install the product with the power cord plugged it can cause an electric shock or a fire Do not allow the video connectors connected to the display to press against the wall Use the included right angle adapters if needed Only use attachments accessories specified by the manufacturer Yo Before installation When installing the product or adjusting the height of the product after installing always do so with 2 people Working alone can cause the product to fall off and result in injury or damage to the product When drilling holes in the wall always use a drill bit and drill of designated diameter Also follow the designated directions for the depth of the hole If the product is installed without following the designated method the product may be unstable and cause a safety Issue Do not install the product near any object that may cause vibration Do not install the product near any high voltage power cable or power source Do not install the product with bare hands Always wear proper work gloves It can cause an injury Do not use the product for purposes other than mounting a display on the wall When installing using the wall mount be cautious of product damage and avoid accidents If you have not fully read and understood the installation manual do not install the pr
Download Pdf Manuals
Related Search