Gas cooktop user manual - Bellini Cooking Appliances
Contents
1. all due precautions m Never leave the appliance unattended when cooking m Do not modify this appliance Burner panel is not designed to operate from an external timer or separate remote control system m Do not use this appliance if it comes in contact with water Do not operate this appliance with wet hands m Do not use large cloths tea towels or similar as the ends could touch the flames and catch fire m Unstable or misshapen pans should not be used on the appliance as they can cause an accident by tipping or spillage Curing use m Do not use or store flammable m Perishable food plastic items and materials in the storage drawer aerosols may be affected by heat and near this appliance should not stored above or below the appliance m Do not spray aerosols in the vicinity of m Ensure the control knobs are in the this appliance while it is in operaiton position when not in use LY GY m This appliance is intended for domestic cooking only It is not designed for commercial or industrial purposes E Prolonged intensive use of the appliance may call for additional ventilation for example opening of a window or increasing the level of mechanical ventilation where present m Use heat resistant pot holders or gloves when handling hot pots and pans m Do not let pot holders come near open flames when lifting cookware m Take care not to let pot2. be serviced Place the bracket B over the holes that match the size of the screws There are one set of screw holes in each corner of the hob H Slightly tighten a screw C through the bracket B so that the bracket is attached to the hob but so that you can still adjust the position Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out On the underneath of the hob adjust the brackets into a position that is suitable for your worktop Then fully tighten the screws C to secure the hob into position gas connection a This appliance must be installed and connected in accordance with installa tion regulations in force in the country in which the appliance is to be used m This appliance is supplied to run on natural gas only and cannot be used on any other type of gas without modification Conversion for use on LPG and other gases must only be undertaken by a qualified person Statutory requirements This installation must conform with the following m Manufacturer s Installation instructions m Local Gas Fitting Regulations m Municipal Building Codes m Refer to AS NZS 5601 1 for Gas Installations m S A A Wiring Code m Local Electrical Regulations m Any other statutory regulations Preparing to install Refer to AS NZS 5601 1 for piping size details These built in cooktops are intended to be inserted in a benchtop cutout Only an officially authorised technic
3. holders or gloves get damp or wet as this causes heat to transfer through the material quicker with the risk of burning yourself m Only ever use the burners after placing pots and pans on them Do not heat up any empty pots or pans m Never use plastic or aluminium foil dishes on the appliance m When using other electrical appliances ensure the cable does not come into contact with the appliance surfaces of the cooking appliance m f you have any mechanical parts eg an artifical heart in your body consult a doctor before using the appliance Do not use a tea towel or similar materials in place of a pot holder Such cloths can catch fire on a hot burner m When using glass cookware make sure it is designed for top plate cooking If the surface is made of glass cracked switch off the appliance to avoid defeat electrocution m To minimise the possibility of burns ignition of flammable materials and spillage turn cookware handles toward the side or center of the top plate without extending over adjacent burners m Always turn burner controls off before removing cookware m Carefully watch foods being fried at a high flame setting m Always heat fat slowly and watch as it heats m Foods for frying should be as dry as possible Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan m Never try to move a pan of hot fat especially a deep fat fryer Wait until the fat is completel
4. the resulting heat build up may damage the appliance m Do not touch the top plate and trivet whilst in use for a certain period after use m As soon as a liquid starts boiling turn down the flame so that it will barely keep the liquid simmering cleaning and maintenance m Cleaning operations must only be carried out when the appliance IAN is completely cool m The appliance should be disconnected from your mains supply before commencing any cleaning process m Clean the appliance regularly preferably after each use m Abrasive cleaners or sharp objects will damage the appliance surface you should clean it using water and a little washing up liquid Metal Brush TON Brush Edible Oil Neutral Detergent _ 2 3 Abrasive Detergent Thinner Benzene Soft cloth i Acidic Alkali Pan support Control knobs m Take off the Pan support m Clean these and the control knobs with a damp cloth washing up liquid and warm water For stubbon soiling soak beforehand m Dry everything with a clean soft cloth Top plate m Regularly wipe over the top plate using a soft cloth well wrung out in warm water to which a little washing up liquid has been added m Dry the top plate thoroughly after cleaning m Thoroughly remove salty foods or liquids from the hob as soon as possible to avoid the risk of corrosion m Stainless steel parts of the appliance may become discoloured over time This is normal because of the h
5. with other commercial wastes for disposal cescniotion of the aopollance BGM604 BGM604 F Model Pan Support Cast Iron Wok pan Support N A Top Plate Stainless Steel Dimension W D H 590 500 95 Ignition device Continuous Ignition Type Gas Connection G1 2 thread Electric supply 240Vac 50Hz 60Hz 2W Burner Feature WOK Semi rapid 2 Auxiliary 1 xQn 8 1kW ae mr vm Model BDGM604 BDGM604 F Pan Support Cast Iron Wok pan Support N A Top Plate Glass Dimension W D H 590 510 105 Ignition device Continuous Ignition Type Gas Connection G1 2 thread Electric supply 240 Vac 50Hz 60Hz 2W WOK Semi rapid 2 Burner Feature Auxiliary 1 8 1kW xQn cescniotion of the appliance Accessories Bracket 4 Self Adhesive Strip 4 Screw 4 NG Regulator 1 Gas cooktop user manual IPEN H ary sf OEP BGMs04 BGMED4 F Injector 4 Test Point Adaptor 1 Gas pipe bend 1 Bellini Instruction Manual 1 Horn ar SZ amp Now to use the appliance The following symbols show on the control panel next to each control knob Black circle gas off A Large flame maximum setting 4 Small flame minimum setting m The minimum setting is at the end of the anti clockwise rotation of the control knob m All operation positions must be selected between the maximum and minimum position m The symbol on
6. Gas cooktop user manual BGM604 BGM604 F BDGM604 BDGM604 F Preface Thank you for choosing the bellini gas cooktop To use this appliance correctly and prevent any potential risk read these instructions before using the appliance Keep these instructions in a place where you can find them easily If you are unsure of any of the information contained in these instructions please contact our customer care centre The manufacturer shall not be responsible for any damages to persons or property caused by incorrect installation or use of the appliance The appliance has NOT been certified for use in countries other than those marked on the appliance The manufacturer also reserves the right to make any modifications to the products as may be considered necessary or useful also in the interests of the user without jeopardising the main functional and safety features of the products themselves The appliance is designed for a domestic environment and not a commercial one contents Preface Safety Warning Instructions for use and maintenance Technical instructions o oaa W 11 12 13 15 16 17 18 20 21 22 23 Safety Instructions Installation Child and People Safety During Use Cleaning and Service Environmental Information Description of the appliance How to Use the appliance Safety and Energy saving advice Cleaning and Maintenance Usin
7. an authorised technician or installer m Prior to installation ensure that the local distribution conditions nature of the gas and gas pressure and the adjustment of the appliance are compatible m The adjustment conditions for this appliance are stated on the label or data plate m This appliance is not connected to a combustion products evacuation device It should be installed and connected in accordance with current installation regulations Particular attention should be given to the relevant requirements regarding ventilaton Before installing turn off the gas and electricity supply to the appliance m All appliances containing any electrical components must be earthed Ensure that the gas pipe and electrical cable are installed in such a way that they do not touch any parts of the appliacne which may become hot m Gas pipe or connector shouldn t be bent or blocked by any other appliances m Check the dimensions of the appliance as well as the dimensions of the gap to be cut in the kitchen unit m The panels located above the work surface directly next to the appliance must be made of non flammable material Both the strati fied surfacing and the glue used to secure it should be heat resistant to prevent deterioration Turn on appliance tap and light each burners Check for a clear blue flame without yellow tipping If burners shows any abnormalities check the following Burner lid on correctly Flam
8. as cooking appliance results in the production of heat and moisture in the room in which it is installed Ensure that the kitchen is well ventilated keep natural ventilation holes open or install a range hood above the gas cook top m Prolonged intensive use of the appliance may call for additional ventilation for example opening of a window or more effective ventilation for example increasing the level of mechanical ventilation where present child and people safety m Do not allow children to play near or with the appliance The appliance gets hot when it is in use Children should be kept away until it has cooled m This appliance is designed to be operated by adults m Children can also injure themselves by pulling pans or pots off the appliance m This appliance is not intended for use by children or other persons whose physical sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safety without supervision or instruction by a responsible person to ensure that they can use the appliance safety quring use m Only use the appliance for preparing food m The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed Ensure that the kitchen is well ventilated keep natural ventilation holes open or install range hood m The heating and cooking surfaces of the appliance become hot when they are in use take
9. ce that may be installed underneath or next to the hotplate The hose should not be subjected to abrasion kinking or permanent deformation and should be able to be inspected along its entire length with the cooktop in the installed position Unions compatible with the hose fittings must be used and all connections tested for gas leaks The supply connection point shall be accessible with the appliance installed WARNING Ensure that the hose assembly is restrained from accidental contact with the flue outlet of an underbench oven gas specification Gas type amp Electrical Heat input and orifice size marked mm Model No Total Heat input pressure power Work burner Rapid burner Semi rapid Auxiliary rapid 12 96 MJ h 6 3 MJ h 3 6 MJ h 29 16 MJ h LPG 0 97 0 72 0 53 2 75kPa 240V BDGM604 B DGM604 F 50 60Hz N Natural Gas 1 60 1 15 0 85 1 0kPa Gas type amp Electrical Heat input and orifice size marked mm Model No Total Heat input pressure power Work burner Rapid burner Semi rapid Auxiliary rapid 12 96 MJ h 6 3 MJ h 3 6 MJ h 29 16 MJ h LPG 0 97 0 72 0 53 2 75kPa 240V BGM604 B GM604 F 50 60Hz NA Natural Gas 1 60 1 15 0 85 1 0kPa 20 electrical connection m This appliance must be earthed m This appliance is designed to be connected to a 220 240V 50 60Hz AC electricity supply m The wires in the mains lead are coloured in accordance with
10. cifications without incurring obligation Whilst every effort is made to ensure that descriptions specifications and other information in this publication is correct no warranty is given in respect thereof and the company shall not be liable for any errors therein Purchased from Co Name Address Date of Purchase Serial number NOTE Consistent with our continuing product development policy improvements may have been made which render the contents of this packaging slightly different to that shown FOR WARRANTY SERVICE CALL 1300 373 199 AUSTRALIA OR 0508 123 108 NEW ZEALAND TO CONNECT YOU TO THE NEAREST AUTHORISED SERVICE CENTRE G SiM GSM Sales Pty Ltd The GSM Sales Pty Ltd Group of Companies has a policy of continual improvement throughout the product range As such the unit contained within may differ slightly from the unit Mustrated on the pack MADE IN CHINA for the GSM Sales Pty Ltd Group of Companies 25
11. e alien substance with a dry with alien substance cloth The holes in the flame spreader are Clean the flame spreader clogged Noise made when The burner lid is badly assembled Assemble the burner lid combusted and ignited correctly Flame goes out when The flame supervision device is Clean the flame supervision in use contaminated with alien substance device Product being cooked has boiled Turn off burner knob Wait one over and extinguished the flame minute and reignite zone A strong draught may have blown Please turn off zone and check the flame out cooking area for draught such as open windows Wait one minute and reignite zone Yellow Flame The holes in the flame spreader are Clean the flame spreader clogged Different gas is used Check the gas used Unstable Flame The burner lid is badly assembled Assemble the burner lid correctly Gas Smell Gas leakage Stop using the product and close the middle valve Open the window to ventilate Contact our service centre by using a phone outside a If problem is not solved please contact our service centre details 23 1 1 In this warranty 1 1 1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and Consumer Act 2010 1 1 2 Company means GSM Sales Pty Ltd ABN 53 007 682 475 of 142 144 Fullarton Road Rose Park SA 5067 Email admin gsmsales com au Australia 1300 373 199 or New Zealand 0508 123 108 1 1 3 Consumer means a co
12. e control knob a Make sure that the flame does not go out by quickly ap turning from maximum flow to minimum flow If it does then remove the control knob and make further by pass screw adjustments to the gas flow testing it again once the adjustment has been made Repeat this process for each one of the gas taps Do not dismantle the tap shaft AN in the event of a malfunction change the whole tap E Before placing the burners back on the top place make sure that the injector is not blocked a A full operational test and a test for possible leakages must be carried out after gas conversion such as soap water or gas detector After completing conversion a qualified technician or installer has to mark V on the right gas category to match with the setting in rating plate Remove the previous setting V mark 22 trouble shooting m Repairs should be performed by a licensed technician only Improper repair may resultin considerable danger to you and others m However some minor problems can be resolved as follows Probable cause Solution Not ignited No Spark Check the electricity supply The burner lid is badly assembled Assemble the lid correctly The gas supply is closed Open the gas supply completely Badly ignited The gas supply is not completely Open the gas supply completely open The burner lid is badly assembled Assemble the lid correctly The ignition plug is contaminated Wip
13. e spreader positioned correctly Burner vertically aligned with injector nipple m A full operational test and a test for possible leakages must be carried out by the fitter after installaion m The flexible hose shall be fitted in such a way that it cannot come into contact with a moveable part of the housing unit and does not pass through any space susceptible of becoming congested m Grease cranes produced at the factory to meet the requirement of all life hob oositioning CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE omm BGM604 BGM604 F BDGM604 BDGM604 F FO 0813 m This appliance is to be built into a kitchen unit or 600mm worktop providing the following minimum distances are allowed o The edges of the hob must be a minimum distance of 60 mm from a side or rear wall o 700 mm between the highest point of the hob surface including the burners and the underside of any horizontal surface directly above it o 400 mm between the hob surfaces providing that the underside of the horizontal surface is in line with the outer edge of the hob If the underside of the horizontal surface is lower than 400 mm then it must be at least 50 mm away from the outer edges of the hob o 50mm clearance around the appliance and between the hob surface and any combustible materials o You must have a gap of at least 25mm and at most 74 mm between the underneath of the appliance and any surface that is b
14. elow it 25 mm MIN An oven must have forced ventilation to install a hob above it Check the dimensions of the oven in the installation manual The cut out size must obey the indication Installing the appliance 1 Remove the pan supports the burner lid and flame spreader and carefully turn the appliance upside down and place it on a cushioned mat Take care that the Ignition devices and flame supervision devices are not damaged in this operation 2 Apply the Self Adhesive strip provided around the edge of the appliance 3 Do not leave a gap in the Self Adhesive strip or overlap the thickness Bottom view T BGM604 BGM604 F The thickness of the Self Adhesive strip is 1 5 mm The width of the Self Adhesive strip is 10 mm sie BDGM604 BDGM604 F The thickness of the Self Adhesive strip is 3 mm The width of the Self Adhesive strip is 10 mm A Do not use a silicon sealant to seal the A SEALING STRIP OA B BRACKET appliance against the bench top This will make it difficult to remove the appliance from the aperture in future particularly if it needs to
15. g instructions Positioning Installing the appliance Gas Connection Gas Specifition Electrical Connection Gas Conversion Troubleshooting Safety instructions m Please take the time to read this Instruction Manual before installing or using the appliance m This instruction booklet must be kept with the appliance for any future reference If the appliance is sold or transferred to another person ensure the booklet is passed on to the new user m The manufacturer declines any liability should these safety measures not be observed m The following marks are made to be easily understood so that you can prevent any accident caused by misuse in advance and use the appliance more conveniently m Read the following contents thoroughly and ensure you understand them A Danger Warnin g a of this mark may result in severe personal injury or AN Caution Neglect of this mark may result in minor personal injury or property damage The following marks are used in the Instruction Manual as follows N caution S No Access amp No Fire Tool Must Do u If gas seems to leak take the actions as follow Do not turn on the light Do not switch on off any electrical appliance and do not touch any electric plug Do not use a telephone 1 Stop using the product and close the middle valve 2 Open the window to ventilate 3 Contact our service centre by using a phone outside The fuel gas contains me
16. ian should connect the appliance Before you begin turn off the gas and electricity supply Natural gas connection LPG gas connection pressure test point pressure test point m A full operational test and a test for possible leakages must be carried out VAN by the fitter after installation Access to the whole length of the connection hose must be possible and the gas hose must be replaced before its use before the end of service life indicated on the hose BeforeLeaving Check all connections for gas leaks with soap and water DO NOT useanakedflame for detecting leaks Ignite all bumers both individually and concurrently to ensure correct operation of gas valves bumers and ignition Turn gas taps to low flame position and observe stability of the flame for each bur ner individually and all together Adhere the duplicate data plateto an accessible location near the hotplate When satisfied with the hotplate please instruct the user on the correct method of operation In case the appliance fails to operate correctly after all checks have been carried out refer to the auth orised service provider in your area gas connection Flexible Hose If installing with a hose assembly it must comply with AS NZS 1869 10 mm ID class B or D no more than 1 mm long and installed in accordance with AS NZS 5601 1 Ensure that the hose does not contact the hot surfaces of the hotplate oven dishwasher or any other applian
17. igh temperatures Each time the appliance is used these parts should be cleaned with a product that is suitable for stainless steel cleaning and maintenance BURNERS m Remove the burner lids and Flame Spreaders by pulling them upwards and away from the top plate m Soak them in hot water and a little detergent or washing up liquid m After cleaning and washing them wipe and dry them carefully Make sure that the flame holes are clean and completely dry m Wipe the fixed parts of the burner cup with a damp cloth and dry afterwards m Gently wipe the ignition device and flame supervision device with a well wrung out cloth and wipe dry with a clean cloth m Before placing the burners back on the top plate make sure that the injector is not blocked u Re assemble the Auxiliary Semi Rapid Rapid and burners as follows 1 Place the flame spreader 4 on to the burner cup 5 so that the ignition device and the flame supervision device extend through their respective holes in the flame spreader The flame spreader must click into place correctly 2 Position the burner lid 1 2 3 onto the flame spreader 4 so that the retaining pins fit into their respective recesses Replace parts in the correct order after cleaning Do not mix up the top and bottom The locating pins must fit exactly into the notches USING INstruCctIONS m Do not modify this appliance This appliance must be installed by
18. ill not apply to any Bellini product 1 7 1 Installed by any person other than a qualified tradesperson or 1 7 2 Subjected to misuse neglect negligence or accidental damage or 1 7 3 Operated in any way contrary to any operating or maintenance instructions or 1 7 4 Improperly handled installed or maintained or 1 7 5 Altered or modified prior to or after installation or 1 7 6 Damaged directly or indirectly by power surges electrical storm damage or connection to incorrect power supply The Australian Consumer Law requires the inclusion of the following statement with this warranty Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY THE CONSUMER MUST CALL 1300 373 199 AUSTRALIA OR 0508 123 108 NEW ZEALAND TO CONNECT TO THE NEAREST AUTHORISED CENTRE 24 1 8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain the benefit of this warranty 1 9 If you live outside the service area of the Company or one of its service agents this warranty does not cover the cost of transport of the Bellini product for
19. nsumer as that term is defined in Section 3 of the Australian Consumer Law as the original purchaser of a Bellini product 1 1 4 Consumer Guarantees means the guarantees under the Australian Consumer Law 1 1 5 You means the Consumer 1 2 Nothing in this warranty affects any person s rights under the Australian Consumer Law The benefits to any Consumer under this warranty are in addition to the rights and remedies available under any Consumer Guarantees 1 3 Subject to the other clauses of this warranty the Company warrants to the Consumer that the Bellini product will be free of manufacturing defects and will perform to the Company s specifications 1 4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which is installed in a residential property 1 5 This warranty commences on the date of purchase of the Bellini product by the Consumer and continues for the benefit only of the Consumer until the expiry of two 2 year Warranty Period 1 6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform to the Company s specifications as a result of some defect in materials components or workmanship Defect then the Company will at its option repair the Bellini product or supply a replacement Bellini product free of charge A replacement Bellini product may differ from the original product purchased by the Consumer 1 7 This warranty w
20. rcaptan so that you can smell the gas leak smell of rotten garlic or egg even where only 1 1000 of the gas is in the air installation m This appliance shall be installed in m Prior to installation ensure that the accordance with regulations in force gas and electrical supply complies and only used in a well ventilated with the type stated on the rating space plate a m Where this appliance is installed in m The gas pipe and electrical cable marine craft or in caravans it should not must be installed in such a way that be used as a space heater they do not touch any parts or the appliance N m This appliance should be installed by a qualified technician or installer m The adjustment conditions for this appliance are stated on the label or data plate m Remove all packaging before using the appliance m After unpacking the appliance make sure the product is not damaged and that the connection cord is in perfect condition Otherwise contact the dealer before installing the appliance m The adjacent cabinetry and all materials used in the installation must be able to withstand a minimum temperature of 85 C above the ambient temperature of the room it is located in whilst in use m In the event of burner flames being accidentally extinguished turn off the burner control and do not attempt to re ignite the burner for at least one minute m The use of a g
21. respond to that of the burner PANS BURNERS Do not use cookware that overlaps the edge of the Semi Rapid Sumer Do not use small diameter cookware on Always use cookware that is large burners suitable for each burner to The flame should never come up the avoid wasting gas and sides of the cookware discolouring the cookware Avoid cooking without a lid or with the Place a lid on the cookware lid half off as this wastes energy Do not use a pan with a convex or Only use pots saucepans and concave bottom frying pans with a thick flat bottom burner as it could tip over right over the burners not to Do not use cookware with a large diameter one side on the burners near the controls which when placed on the middle of the burner may touch the controls or be so close to them that they increase the temperature in this area and may cause damage Never place cookware directly on top of Place the cookware on top of the burner the trivet Do not place anything eg flame tamer between pan and pan support as serious damage to the appliance may result Do not use excessive weight and do not Handle cookware carefully hit the cooktop with heavy objects when they are on the burner m It is not recommended to use roasting pans frying pans or grill stones heated simultaneously on several burners because
22. service nor the service agent s traveling costs to and from your home 1 10 If you are required to transport the Bellini product to the Company or its service agent you must ensure it is safely disconnected by a qualified tradesman and securely packed and insured The Company does not accept any responsibility for loss or damage of the Bellini product prior to it being received by the Company or its service agent 1 11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the Bellini product by the Company whether it is the original or a repaired and or a replacement Bellini product and for any other expenses you incur in claiming under this warranty 1 12 The Company or its service agent will examine any Bellini product and if the Company determines that it is defective through no fault of the Owner and is otherwise undamaged the Company will repair or replace the Bellini product in accordance with this warranty DO NOT SEND IN THIS WARRANTY Fill out the following details and file with your purchase invoice RETAIN amp FILE WITH YOUR RECEIPT Your Purchase Receipt Invoice is proof of date of purchase If you are unable to establish the date of purchase or if the fault is not covered by this warranty or if the product is found to be in working order you will be required to bear all service call charges GSM Sales Pty Ltd reserves the right to discontinue items modify designs and change spe
23. the control panel next to the control knob will indicate which burner it operates Automatic ignition with flame failure safety device The appliance is fitted with a flame failure safety device on each burner which is designed to stop the flow of gas to the burner head in the event of the flame going out Now to use the appliance LO O10 WS Automatic ignition with flame failure safety device To ignite a burner O Press in the control knob of the burner that you wish to light and turn it anti clockwise to the maximum position If you keep the control knob depressed the automatic ignition for the burner will operate You should hold down the control knob for 15 seconds after the flame on the burner has lit If after 15s the burner has not lit stop operating the device or wait at least 1 min before attempting a further ignition of the burner After this 15 second interval to regulate the flame you should continue turning the control knob anti clockwise until the flame is at a suitable level The operating position MUST be at a position between the maximum and minimum position To switch the burner off turn the control knob fully clockwise to the gas off position In the event of a power failure the electronic ignition will not function but you can light the gas burners in this instance with a match or separate gas ignition device Safety and energy saving advice The diameter of the bottom of the pan should cor
24. the following code Green yellow Earth Blue Neutral Brown Live m The wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol u WIRING DIAGRAM Switch 2 L ACINPUT swich 3 N ei Switch 4 IGNITION When the power cord is damaged it must be replaced by the manufacturer to produce customer service agent or similarly qualified personnel 21 gas adustment m Take precautions on the operations and adjustments to be carried out when converting from one gas to another a All work must be carried out by a qualified technician Before you begin turn off the gas and electricity supply to the appliance Change the injector of the burners Remove the pan support Burner lid and Flame spreader Unscrew the injector using a 7 mm box spanner and replace it with the stipulated injector for new gas supply Carefully reassemble the all components After injectors are replaced it is advisable to strongly tighten the injector in place Turn the taps down to minimum Remove the knob from the tap and place a small os bladed screwdriver in the centre of the tap shaft lt Controlhandle The correct adjustment is obtained when the flame has a length of about 3 4 mm For LPG gas the adjusting screw 2 Adjustment of minimum level of the flame Tap ae must be tightly screwed in D ee Refit th
25. y cool cleaning and service m Never use abrasive or caustic m This appliance should only be cleaning agents repaired or serviced by an authorised Service technician and only genuine approved spare parts should be used m Before attempting to clean the appliance it should be disconnected from the mains and cooled m You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance environmental information m After installation please dispose of the packaging with due regard to safety and the environment D m When disposing of an old appliance make it unusable by cutting off the cable Correct Disposal of This Product m Waste Electrical amp Electronic Equipment m This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources m Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling m Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed
Download Pdf Manuals
Related Search