CS210 - Campbell Scientific
Contents
1. Mass 1 oz ounce 28 35 g 1 Ib pound weight 0 454 kg Length 1 in inch 25 4 mm 1 ft foot 304 8 mm Pressure 1 psi Ib in 68 95 mb 1 yard 0 914 m 1 mile 1 609 km Volume 1 UK pint 568 3 ml 1 UK gallon 4 546 litres 1 US gallon 3 785 litres In addition while most of the information in the manual is correct for all countries certain information is specific to the North American market and so may not be applicable to European users Differences include the U S standard external power supply details where some information for example the AC transformer input voltage will not be applicable for British European use Please note however that when a power supply adapter is ordered it will be suitable for use in your country Reference to some radio transmitters digital cell phones and aerials may also not be applicable according to your locality Some brackets shields and enclosure options including wiring are not sold as standard items in the European market in some cases alternatives are offered Details of the alternatives will be covered in separate manuals Part numbers prefixed with a symbol are special order parts for use with non EU variants or for special installations Please quote the full part number with the when ordering Recycling information At the end of this product s life it should not be put in commercial or domestic refuse but sent for recycling Any batteries contained2. 1 Batt Voltage P10 1 1 Loc Batt_Volt 2 Panel Temperature P17 1 2 Loc PnITempC Turn the CS210 on and leave it on The CS210 needs approximately 10 seconds to stabilize First scan will be low 3 Do P86 1 41 Set Port 1 High 4 Volt SE P1 1 Reps 15 5000 mV Fast Range 1 SE Channel 3 Loc Enc _RH 0 1 Multiplier 0 Offset 5 If time is P92 1 0 Minutes into a 2 1440 Minute Interval 3 10 Set Output Flag High 6 Set Active Storage Area P80 1 1 Final Storage 2 100 Array ID 7 Real Time P77 1 1220 Year Day Hour Minute midnight 2400 8 Minimum P74 1 Reps Value Only Loc Batt_Volt 9 Minimum P74 1 Reps 0 Value Only 2 Loc PnITempC 10 Maximum P73 Reps 0 Value Only 2 Loc PnITempC 11 Maximum P73 0 3 Table 2 Program 02 0 0000 Table 3 Subroutines End Program User Manual Reps Value Only Loc Enc_RH Execution Interval seconds 6 Enclosure Humidity 7 Maintenance Change the enclosure desiccant packs model number 4905 when the enclosure relative humidity exceeds 40 Campbell Scientific recommends that all cable entry ports that do not use a sealed bulkhead connector be sealed with plumbers putty and that desiccant packs be placed inside the enclosure Spikes in the enclosure humidity are a result of opening the enclosure door and allowing ambient air inside the enclosure The enclosure relative hu
3. CS210 Black C2 White SEI Clear G Declare Public Variables Example Public batt_volt Public Enc_RH Define Data Tables DataTable Daily 1 1 Datalnterval 0 24 hr Minimum 1 batt_volt 0 0 Maximum 1 Enc_RH False 0 EndTable User Manual Main Program BeginProg Scan 10 Sec Battery Batt_volt Power the CS210 using C2 and leave it on PortSet C2 1 VoltSe Enc_RH 1 1 0 1 0 Set the sensor to 100 if it exceeds 100 If Enc_RH gt 100 Then Enc_RH 100 CallTable Daily NextScan EndProg 5 2 Edlog Examples Example 3 is a portion of a CR10 X program but our CR500 CR510 and CR23X dataloggers are programmed similarly Wiring used for the CR10 X program is included in Table 3 Example 4 is an Edlog program written for a 21X Micrologger wiring used for the 21X program is included in Table 3 The 21X program turns on control port 1 to power the CS210 Notice that the scan rate is set at 10 seconds The sensor won t give a good reading until the second scan e Table 3 Wiring for Examples 3 and 4 Example 3 Sample CR10 X Program Measure the CS210 relative humidity 01 V olt SE P1 1 Reps 2500 mV Slow Range CR510 2500 mV CR23X 1000 mV SE Channel White wire SE 6 Clear wire G Loc RH_enc Mult Offset CS210 Enclosure Humidity Sensor Example 4 Sample 21X Program 21X Table 1 Program 01 10 Execution Interval seconds
4. IVANVIA JASA TE CAMPBELL E SCIENTIFIC eo WHEN MEASUREMENTS MATTER CS210 Enclosure Humidity Sensor nr dI Issued 21 10 13 Copyright 1996 2007 Campbell Scientific Inc Printed under licence by Campbell Scientific Ltd CSL 1007 Guarantee This equipment is guaranteed against defects in materials and workmanship This guarantee applies for twelve months from date of delivery We will repair or replace products which prove to be defective during the guarantee period provided they are returned to us prepaid The guarantee will not apply to e Equipment which has been modified or altered in any way without the written permission of Campbell Scientific e Batteries e Any product which has been subjected to misuse neglect acts of God or damage in transit Campbell Scientific will return guaranteed equipment by surface carrier prepaid Campbell Scientific will not reimburse the claimant for costs incurred in removing and or reinstalling equipment This guarantee and the Company s obligation thereunder is in lieu of all other guarantees expressed or implied including those of suitability and fitness for a particular purpose Campbell Scientific is not liable for consequential damage Please inform us before returning equipment and obtain a Repair Reference Number whether the repair is under guarantee or not Please state the faults as clearly as possible and if the product is out of the guarantee period it should
5. ampbell Scientific dataloggers are given in Table 1 and Figure 2 The probe is measured by a single ended analogue input channel Table 1 Datalogger Connections CR800 CR850 CR1000 CR3000 CR5000 CR9000 X Description Colour CR200 series CR10 X CR500 CR510 CR23X 21X Input Reference C G Power Black cC2 5w Control Port Signal and Power Reference Clear 5 VDC Power Black Signal White Figure 2 CS210 Wiring User Manual 5 Programming This section is for users who write their own datalogger programs A datalogger program to measure this sensor can be created using Campbell Scientific s Short Cut Program Builder Software You do not need to read this section to use Short Cut The relative humidity signal from the CS210 is measured using a single ended analogue measurement CRBasic instruction SEVolt or Edlog Instruction 1 The CR200 series and 21X use a control port to power the CS210 At the beginning of the program the control port needs to be turned on and the port should remain on It takes the CS210 approximately 10 seconds for the reading to become stable after the port has been turned on Depending on the scan rate the first few measurements from the CS210 could be low The probe output scale is 0 to 1000 millivolts for the relative humidity range of 0 to 100 Table 2 provides calibration information for relative humidity Table 2 Calibration for Relative Humidity Units a Offs
6. ative humidity inside an equipment enclosure deployed in the field The CS210 was once known as the 10162 2 Specifications 3 Installation NOTE Sensor Elan HM2000 series precision bulk polymer Relative Humidity Measurement Range 0 to 100 non condensing RH Output Signal Range 0 to 1 0 VDC Accuracy at 25 C unspecified 0 to 10 Relative Humidity 3 RH 10 to 90 Relative Humidity unspecified 90 to 100 Relative Humidity Typical Long Term Stability Better than 3 RH per year Response Time at 25 C 90 response 10 seconds for a 30 to 90 RH step change Operating Temperature 0 C to 50 C Storage Temperature 40 C to 80 C Probe Length 2 6 cm 1 02 in Probe Cross Section Area 0 6 cm x 1 1 cm 0 23 in x 0 43 in Current Consumption lt 0 5 mA Supply Voltage 5 0 25 VDC Settling Time 10 seconds Mount the CS210 inside the environmental enclosure or onto a datalogger using the mounting block and the wire tie included with the sensor Figure 1 The black outer jacket of the cable is Santoprene rubber This compound was chosen for its resistance to temperature extremes moisture and UV degradation However this jacket will support combustion in air It is rated as slow burning when tested according to U L 94 H B and will pass FMVSS302 Local fire codes may preclude its use inside buildings CS210 Enclosure Humidity Sensor Figure 1 CS210 Installed on a CR1000 Connections to C
7. be accompanied by a purchase order Quotations for repairs can be given on request It is the policy of Campbell Scientific to protect the health of its employees and provide a safe working environment in support of this policy a Declaration of Hazardous Material and Decontamination form will be issued for completion When returning equipment the Repair Reference Number must be clearly marked on the outside of the package Complete the Declaration of Hazardous Material and Decontamination form and ensure a completed copy is returned with your goods Please note your Repair may not be processed if you do not include a copy of this form and Campbell Scientific Ltd reserves the right to return goods at the customers expense Note that goods sent air freight are subject to Customs clearance fees which Campbell Scientific will charge to customers In many cases these charges are greater than the cost of the repair CAMPBELL SI SCIENTIFIC Campbell Scientific Ltd Campbell Park 80 Hathern Road Shepshed Loughborough LE12 9GX UK Tel 44 0 1509 601141 Fax 44 0 1509 601091 Email support campbellsci co uk www campbellsci co uk PLEASE READ FIRST About this manual Please note that this manual was originally produced by Campbell Scientific Inc primarily for the North American market Some spellings weights and measures may reflect this origin Some useful conversion factors Area 1in square inch 645 mm
8. et mV 5 1 CRBasic Examples Example 1 is a sample CRBasic program written for a CR1000 but our CR800 CR850 CR3000 CR5000 and CR9000 X dataloggers are programmed similarly Example 2 is a CRBasic program written for a CR200 datalogger The CR200 program turns on control port 2 to power the CS210 Notice that the scan rate is set at 10 seconds The sensor won t give a good reading until the second scan Example 1 Sample CR1000 Program CRI000 Series Datalogger SENSOR WIRING CS210 Black 5V White SEI Clear G Declare Public Variables Public PanelTempC Public Batt_Volt Public Enc_RH CS210 Enclosure Humidity Sensor Define Data Tables DataTable Daily 1 1 Datalnterval 0 1 Day 10 Minimum 1 Batt_Volt FP2 0 False Minimum 1 PanelTempC FP2 False False Maximum 1 PanelTempC FP2 False False Maximum 1 Enc_RH FP2 False False EndTable Main Program BeginProg Scan 10 Sec 0 0 PanelTemp PanelTempC 250 Battery Batt_volt Measure CS210 Sensor is on all the time Don t need a delay VoltSe Enc_RH 1 mV2500 1 1 0 250 0 1 0 Set the sensor to 100 if it exceeds 100 If Enc_RH gt 100 Then Enc_RH 100 CallTable Daily NextScan EndProg Example 2 Sample CR200 Program CR200 Series Datalogger To create a different opening program template type in new instructions and select Template Save as Default Template date program author SENSOR WIRING
9. midity will return its nominal values values before the enclosure door was opened in approximately three to four hours The CS210 does not have any user serviceable parts nor does it require any routine maintenance Replace the CS210 probe every three to five years of continuous use If the probe fails replace it with a new one CS210 Enclosure Humidity Sensor CAMPBELL SCIENTIFIC COMPANIES Campbell Scientific Inc CSI 815 West 1800 North Logan Utah 84321 UNITED STATES www campbellsci com e info campbellsci com Campbell Scientific Africa Pty Ltd CSAf PO Box 2450 Somerset West 7129 SOUTH AFRICA www csafrica co za e sales csafrica co za Campbell Scientific Australia Pty Ltd CSA PO Box 8108 Garbutt Post Shop QLD 4814 AUSTRALIA www campbellsci com au e info campbellsci com au Campbell Scientific do Brazil Ltda CSB Rua Luisa Crapsi Orsi 15 Butant CEP 005543 000 S o Paulo SP BRAZIL www campbellsci com br e suporte campbellsci com br Campbell Scientific Canada Corp CSC 11564 149th Street NW Edmonton Alberta TSM 1W7 CANADA www campbellsci ca e dataloggers campbellsci ca Campbell Scientific Centro Caribe S A CSCC 300N Cementerio Edificio Breller Santo Domingo Heredia 40305 COSTA RICA www campbellsci cc e info campbellsci cc Campbell Scientific Ltd CSL Campbell Park 80 Hathern Road Shepshed Loughborough LE12 9GX UNITED KINGDOM www campbellsci co uk e sales campbellsci co
10. uk Campbell Scientific Ltd France 3 Avenue de la Division Leclerc 92160 ANTONY FRANCE www campbellsci fr e info campbellsci fr Campbell Scientific Spain S L Avda Pompeu Fabra 7 9 Local 1 08024 BARCELONA SPAIN www campbellsci es e info campbellsci es Campbell Scientific Ltd Germany Fahrenheitstrasse13 D 28359 Bremen GERMANY www campbellsci de e info campbellsci de Please visit www campbellsci com to obtain contact information for your local US or International representative
11. within the product or used during the products life should be removed from the product and also be sent to an appropriate recycling facility Campbell Scientific Ltd can advise on the recycling of the equipment and in some cases Sz arrange collection and the correct disposal of it although charges may apply for some items or territories For further advice or support please contact Campbell Scientific Ltd or your local agent fz CAMPBELL E SCIENTIFIC Campbell Scientific Ltd Campbell Park 80 Hathern Road Shepshed Loughborough LE12 9GX UK Tel 44 0 1509 601141 Fax 44 0 1509 601091 Email support O campbellsci co uk www campbellsci co uk Contents PDF viewers note These page numbers refer to the printed version of this document Use the Adobe Acrobat bookmarks tab for links to specific sections 1 General 2 Specifications cui ledere 3 Installation 5 Programming dai 3 5 1 CRBasic Examples 5 2 Edlog Examples 6 Enclosure Humidity nennen 7 7 Maintenance Figures jean CS210 Installed on a CR1000 2 CS210 Wiring Tables Datalogger Connections 25208002 snetstensensniiksss Calibration for Relative Humidity 3 Wiring for Examples 3 and 4 N m CS210 Enclosure Humidity Sensor 1 General NOTE The CS210 Enclosure Humidity sensor contains an Elan HM2000 series precision bulk polymer relative humidity sensor It is used to monitor the rel
Download Pdf Manuals
Related Search