Home
BCM91101 911 Antenna tuner
Contents
1. 911 automatic antenna tuner External GPS receiver option Feed through insulator P N BCA91701 Connection for external fan unit option If required Antenna Auxiliary connector 6 metre power cable supplied with transceiver Optional 6 or 10 metre extension cable with connectors P N BCA90032 40 Heavy duty fuse amp holder P N BCA20021 Coaxial control cable PIN BCA90032 2050 transceiver body Microphone Extension speaker supplied standard with 2050 transceiver BASE STATION INSTALLATIONS Antenna Various antenna configurations such as vertical whips long wires and loops can be used for base station installations using the Barrett 911 Automatic Antenna Tuner In general however the following points should be considered 1 The antenna should be mounted as far away as possible from buildings trees vegetation and sources of electrical interference If metallic masts or supports are used arrange insulators to ensure the antenna is spaced at least 2 metres from the mast 2 Remember the radiating part of the antenna starts at the tuner The location of the bottom portion of the antenna is very important 3 Horizontal wire antennas have maximum radiation broadside to the antenna when the frequency is less than 1 4 wavelength Radiation is at a minimum at the end points of the antenna 4 Inverted V installation of horizontal antennas minimises the directivity and is recommend
2. KD BARRETT COMMUNICATIONS 911 Automatic antenna tuner Installation instructions 90 0 38 38 Antenna 2a A ja Diameter 6mm Connection ry o o qd E gt Kee 2 e feol 8 ole BARRETT 911 AUTOMATIC ANTENNA TUNER ie o co o o ad 230 68 e a 285 Control Cable Gland Ground Connection General The Barrett 911 Automatic Antenna Tuner is designed for use in land base station and maritime HF services Primarily designed for operation with end fed un balanced antennas such as whips and long wires the tuner is built in a waterproof impact resistant moulded ABS plastic enclosure Specifications Frequency range 1 6 to 30 MHz Maximum power input 150 Watts PEP Input impedance range 50 Ohms nominal DC power requirement 13 8V DC Input current average 0 9Amps Random tune time Recurrent tune time Typically less than 2 seconds Typically less than 10 milliseconds Minimum antenna length 2 6 metres 3 3 to 30 MHz 7 0 metres 1 6 to 30 MHz Operating temperature 10C to 60C Dimensions 350 x 284 x 70mm Weight 3 4 Kg BCM91101 2 nc YD MARINE INSTALLATIONS Antenna On sailing vessels the antenna can either be an insulated backstay or a whip antenna mounted vertically usually on the stern Best performance will be achieved by using an insulated backstay as the radiating length will be longer than that available when using a whip The
3. system operation An inadequate ground system is the primary cause of poor performance and tuning problems There is little point in installing the antenna unless a good ground system can be provided Metal hulled vessels provide an almost perfect ground The tuner ground terminal should be connected directly to the hull using the shortest possible ground strap The point of connection to the hull should be prepared so that it is free of paint and rust to ensure a good contact area with minimum electrical resistance Wooden or fibreglass vessels present more of a problem to ground Ideally the vessel should be fitted with an external copper ground sheet connected to the interior of the vessel by suitable stud or an earth plate If the vessel is yet to be constructed then in the case of fibreglass vessels a thin copper sheet with an area of not less than 4 square metres should be moulded into the hull during lamination Asuitable heavy strap should be connected to the sheet and left free for earth connection Should neither of these methods be available it will be necessary to bond as many large metallic objects such as the engine and propeller shaft together to form a ground Which ever method is used the ground run from the ground system to the antenna tuner should be as short as possible and use copper strap at least 50mm wide wider if available Consideration must always be given to the problem of electrolysis Severe structural damage
4. 10 or 6 metre extension cable Extension speaker and microphone supplied with connectors P N BCA90032 40 standard with remote head QO Standard interface supplied with 911 l antenna tuner Remote control head supplied standard with 930 950 remote control trunk mount transceiver Note The 500 900 series transceiver can be powerd with a 522 922 power supply if mains power is available Barrett 2050 connection detail for base station installation a 7 al O 13 8 VDC 9 O GND BLACK J 1 l 13 8 VDC P Extension speaker supplied standard with 2050 transceiver 911 automatic antenna tuner Antenna External GPS receiver option Microphone Connection for external fan unit option Heavy duty fuse amp holder P N BCA20021 Auxiliary connector 6 metre power cable supplied Coaxial control cable P N BCA90032 with transceiver Optional 6 or 10 metre extension cable with connectors P N BCA90032 40 O00000 000000 2050 transceiver body Note The 2050 transceiver can be powerd with a 2022 power supply if mains power is available BCM91101 2
5. in the pipe that will increase the resistance path to ground 3 The water pipe enters soil with good conductivity 4 Alow resistance joint is made with the water pipe Frequently the ground conductivity will not be sufficient to provide a satisfactory ground for the Barrett 911 Tuner This will almost certainly be the case in well drained sandy soils or on rock In these cases a counterpoise must be used as a ground system This will also be the case in rooftop installations where no existing ground plate such as metal roofing exists A counterpoise can consist of radial wires or a mesh made of materials such as chicken wire If radial wires are used the counterpoise should consist of at least 8 to 10 radial wires When radials or mesh are used at ground level it is recommended that they be buried a few centimetres below the surface ELECTRICAL CHECKOUT After mechanical installation is complete select the highest frequency to be used on the transceiver Adirectional watt meter such as a Bird Model 43 should be inserted in the coaxial transmission line between the transceiver and the tuner The tune mode on the transceiver is then energised refer to the transceiver user manual Upon application of RF energy the tuner should start to tune indicated by the clattering of the tuner relays After a few seconds the relay noise will cease and the transceiver should indicate a successful tune and the wattmeter reflected power should indicate
6. may occur if electrolysis is present Corrosion All connections in marine situations are subject to corrosion and oxidation To minimise this all joints should be cleaned and have silicon grease applied before assembly Under severe conditions joints should be protected with self vulcanising rubber tape Barrett 950 or 930 connection cetail for marine installation Na oe oo ssa ee L IO GND BLACK 6 metre cable amp connectors supplied with 911 911 automatic antenna tuner 8 antenna tuner Feed through insulator P N BCA91701 If required Heavy duty fuse amp holder P N BCA90018 Antenna 6 metre power cable supplied with transceiver P N BCA90016 900 series transceiver body Cable amp connectors supplied with 12 Extension speaker and microphone supplied 911 antenna tuner standard with remote head Optional 10 or 6 metre extension cable with connectors P N BCA90032 40 Standard interface supplied with 911 antenna tuner Remote control head supplied standard with 930 950 remote control trunk mount transceiver Q _Lplional accessory interface 7 Barrett 2050 connection detail for marine installation Camm O A 13 8 VDC 0 BLACK o k 13 8 VDC
7. a low value consistent with a VSWR of better than 2 1 If the cover of the tuner is removed the PCB mounted TUNED LED should be illuminated Now select the lowest desired frequency on the transceiver and repeat the above procedure The result should be the same except that the tune cycle may take somewhat longer If the above procedure does not give the results as indicated check that the antenna length and connections are correct and re check all ground earth connections Note When received the Barrett 911 Automatic Antenna Tuner memory system will usually not have any pre stored tuning information appropriate to your installation To allow the 911 to learn its tuning information simply proceed from one channel to the next allowing the normal tune cycle to take place Each successful tune is memorised so that when that channel is re selected the tuner will almost instantaneously re tune to that frequency Barrett 950 or 930 connection detail for base station installation ihc al ae on a bo aee oy 13 8V ro f gs sa D AA GND BLACK D 911 automatic antenna tuner 6 metre cable amp connectors supplied with 911 antenna tuner Antenna Heavy duty fuse amp holder P N BCA90018 Optional interf BN BCAGOI mamaca 6 Metre power cable supplied with transceiver 4 a ERN supplied with 10 500 or 900 series transceiver body 6 Optional
8. ed for omni directional coverage 5 High voltages are present on the antenna system The antenna tuner and antenna should be located or protected so that there is no possibility of accidental contact Transceiver and Tuner Mounting The transceiver should be mounted in a suitable position allowing easy operator access The antenna tuner should be mounted preferably out of the weather and as close to the ground earth point as possible The interconnect cable supplied with the antenna tuner should be routed back to the transceiver away from other cables and connected as indicated in the diagram Ground Earth System The ground earth system is a key part of the overall antenna system and consequently the system operation An inadequate ground system is the primary cause of poor performance and tuning problems There is little point in installing the antenna unless a good ground system can be provided In areas of good ground conductivity ie ground always damp an effective ground can be made through a grounding rod This should be approximately 3 metres in length and should be installed as close to the tuner as possible Several rods bonded together will improve the ground contact Aleased preferred method and one that should be avoided if possible is to use existing metal water pipes as a ground providing 1 The water pipe is close to the tuner and the water pipe enters the ground close to the tuner 2 There are no joints or couplings
9. top insulator on the backstay should be approximately 300mm from the mast and the bottom insulator should be at eye level above the deck The distance between insulators should be greater than 10 metres and less than 35 metres Awhip antenna is generally used on small to medium sized power vessels There are different length whips to suit the vessel length Transceiver and Tuner Mounting Select a suitable position in the vessel to mount the transceiver It should be a position that is out of the weather and easily accessible to the operator whilst as close as practical to the 13 8V DC power source Mount the transceiver to a solid fixing point using the mounting cradle Make sure there is sufficient space at the rear of the transceiver to connect the power and antenna cables The antenna tuner should be mounted as close to the antenna feed point as possible In metal vessels the length of the feeder from the antenna tuner to the feed through insulator inside the vessel should be keptless than 1 metre The antenna feed cable should be a suitable high voltage cable Care should be taken to avoid sharp points when terminating the cable to prevent corona discharges The interconnect cable supplied with the antenna tuner should be routed away from other cables back to the transceiver and connected as indicated in the diagram overleaf Ground Earth System The ground earth system is a key part of the overall antenna system and consequently the
Download Pdf Manuals
Related Search
Related Contents
Archives nationales du monde du travail Sony DSC-H20/B User's Manual STYLO MARQUEUR PERMANENT Direction générale Environnement Berkem S.A. Le Marais Ouest F BENUTZERHANDBUCH ペツル プロフェッショナル カタログ 2013 技術情報 屋根とスロープ アイガモンの取扱い説明書はこちら (PDFファイル) Istruzioni d`uso VEGABAR 81 Cabstone 95122 soundbar speaker Copyright © All rights reserved.