DEFENDER WIRELESS GSM BURGLAR ALARM
Contents
1. and the alarm system will start the auto dial process 2 To disarm your alarm system please press the open padlock button Once pressed the system will disarm and you will be able to move around freely inside the property without triggering the alarm system Please note that if you have one of our smoke detectors even in disarm mode they will activate the alarm system and sound the siren and auto dial the phone numbers 3 Should you wish to activate the panic feature of the alarm please press the bell button and hold it in the alarm will now sound and also call and or text you WHEN THE ALARM IS ACTIVATED 1 When one of the sensors is activated the alarm panel LED in the lower right hand area next to the words Alarm will light up at this time the alarm will start to make its auto dial call to the first number you have entered into the system It will then play back the message you recorded and at the same time if you have set it up it will send the text message to the phone number of your choice 2 If the first telephone number does not answer in 40 seconds the alarm will try the second third and so on until someone answers the call Once the call is answered it will no longer try the numbers after it 3 When the alarm connects the call to you you MUST press the button to acknowledge the call this will terminate the call and stop the alarm system otherwise it will try to call the other numbers in the sequence This is in2. case the alarm calls a mobile or landline number and gets to an answer phone Thus if the call is connected to an answer phone and the button is not pressed it will move onto the next number and so on 4 You can disarm the alarm system by pressing the number 5 on your phones key pad Pressing the number 1 on your phone will then enable you to listen into the room and hear what is happening in the property Press the number 2 to turn on the siren and press the number 3 to turn off the siren or press the number 4 to turn the alarm system back on again You can also play back the recorded message if you wish by pressing the button on your phones key pad PHONING YOUR ALARM SYSTEM 1 The alarm system can be operated by remote control via text message or by pressing the buttons on your phones key pad 2 Tocontrol your alarm by telephone key pad you must telephone the number of the SIM card inside the alarm system After 3 4 rings the alarm will connect the call and make a BEEP sound When you hear this BEEP please enter your 4 digit password if this is entered correctly it will BEEP 2 times if incorrect it will make a long BEEP sound You have 3 attempts to enter the number after which it will disconnect the call You can press the following buttons to control the alarm system from your telephone 1 will enable you to listen in 2 will turn the siren on 3 will turn the siren off 4 will turn your alarm system on an
3. Global Gadgets DEFENDER WIRELESS GSM BURGLAR ALARM USER MANUAL This burglar alarm system works with a mobile phone pay as you go SIM card You can use any provider apart from 3Network However we have found that the best SIM to use is a Virgin SIM Virgin is one of the only providers to keep the SIM active even if not used they also do not have SIM security setting turned on by default If you use another providers SIM you may need to put the SIM into a mobile phone and turn off all SIM security options The alarm will call up to 6 phone numbers to inform the person at the other end of the phone that your alarm has been triggered Additionally it has the option to send a text message as well If you find the GSM won t call you as expected please make sure that all SIM security settings are set to either OFF NO or NONE as all SIM security options must be turned off If you can call the alarm or text the alarm OK then SIM security options ARE still active INSTALLTION INSTRUCTIONS First please purchase from your local shops either a pay as you go SIM card It cannot be a contract SIM only a pay as you go SIM will work Please make sure that the SIM is active and has credit on it Most SIM cards need to be placed in a mobile phone first to then be enabled Also please make sure you turn off any PIN request and security codes as this will stop the alarm auto dialling 1 Place the SIM card in the slot on the top side of the GSM alarm system by
4. as follows 9 43 If you want the siren to sound continually when activated until the alarm is disarmed by the key fob or by you disarming it from your phone please enter the following 9 4 Be careful doing this as you could upset neighbours very quickly if left sounding for a long time To change the default password from 1234 to your own number please complete the following on the white key pad let s say the number you want it to be is 6666 7 66666666 If you want to set your alarm system up so that it sends a text message please complete the following on the white key pad 0 phone number If the system is then activated the alarm will send out a short text message to inform you that either a sensor has been triggered or the power has been lost To turn this feature off please enter the following 0 10 To set up a exit delay so that you can arm the system and then have time to exit the property please do as follows 9 50 the delay time in seconds 10 99 11 To set up a entry delay so that you can open the door and then have time to enter the property to then disarm the system please do as follows 9 51 the delay time in seconds 10 99 ARMING YOUR ALARM and the key fobs 1 To arm your alarm system using the key fobs please press the closed padlock button This will put the alarm system in armed mode From here if any sensor is activated the siren will sound
5. d lastly 5 will turn your alarm system off CONTROLLING THE ALARM BY TEXT MESSAGE 1 You can control your alarm system by text message if you wish However to do this you must use the text code below and all text must be in capital letters UPPER CASE The message string must contain your current password as well as the required commands as below Default password is 1234 for this example we will use 1234 1234ARM This will arm the alarm system and the reply message will be Host is activated 1234DISARM This will disarm the system and the reply message will be Host is deactivated 1234ONSIREN This will turn the siren on and reply message will be The siren is opened 1234OFFSIREN This will turn the siren off and the reply message will be The siren is closed 1234CHECK This will either turn the alarm system on or it will turn the alarm system off depending on its current state the reply message will be either Host is activated or Host is deactivated A C POWER SUPPLY amp BACKUP BATTERY 1 The alarm system is supplied with a lithium backup battery which will provide your alarm with around 72 hours of power should the properties power be cut or removed If this does happen the alarm will send a text message to the designated mobile phone with the message AC POWER SHUT OFF once the power is reconnected the alarm will automatically send the message AC POWER RECOVERED You mu
6. e the first number 1 with number 2 ie 2 0123412345678 Please repeat this up to 6 times To delete an auto dial telephone number please enter the following on the white key pad 1 to remove the second place number please do as follows pad 2 and so on All sensors and remote key fobs have been pre linked for you by our staff unless otherwise requested However should you wish to change this or link other devices in please complete the following on the white key pad 9 90password then add zone number 01 16 then activate the sensor one time If a door contact place the magnet on the sensor and then move it away if it is a sensor please wave your hand in front of the sensor if a smoke detector please press the test button You should hear a BEEP from the alarm system to confirm the link has been received lastly please press the button again to save the settings To cancel a key fob from the system Be careful doing this 9 91password To cancel a detector from the system Be careful doing this 9 92password This will delete all your sensors from the system so if you do this all sensors will need to be inked in again To set the sirens run time Default run time is 1 minute please enter the following commands on the white key pad 9 4 The indicates how many minutes you want the alarm to sound for for instance if you want it to sound for 3 minutes please do
7. he Defender alarm system can have other devices linked to it please find below details of the extras you can add to the system These cost extra unless stated in your purchased kit Wireless arm disarm keypad 1 How to use wireless doorway keypad Default password 1234 FUN password ARM Arm the host FUN password DIS Disarm the host FUN password BYP Bypass the host FUN password SOS Host emergency alarm 2 How to change wireless keypad s default password If you change the GSM panel s default password 1234 into 5678 you should then change the password of this keypad into 5678 or it won t work with GSM panel gt press FUN key then all the LED light up press 2 and FUN together gt enter new password two times 56785678 gt two BEEP sound indicates changing ok 3 How to link the key pad to your alarm Using your programming key pad please enter 9 901234 then quickly on the new arm and disarm key pad press FUN1234 SOS The main alarm panel will beep at you now back on the programming pad please press the button 4 Parameters Built in battery 3 7V 500mA lithium battery Working current 30Ma Static current 5uA Standby 1 000minutes Recharge time 12 24hrs Power adapter 6V 1A
8. ion and make sure that the tamper switch on the back of the siren is pressed in and secure If this is not pressed in the siren will not function and will sound Lastly using the supplied power adaptor for the wireless strobe siren connect this and plug the transformer into your wall socket i Quick Guide Learn the remote control 9 901234 Delete the remote control 9 911234 Learn the door contact 9 90123403 Learn the PIR 9 90123402 Learn the smoke sensor 9 90123404 Learn the panic button 9 90123401 Delete accessory 9 921234 Mute alarm 9 0 Sound alarm 9 1 Arm notification sound off 9 2 Arm notification sound on 9 3 Time for siren s sounding 9 4 1 9 Exit delay 9 50 00 99 Entry delay 9 51 00 99 Code for wireless black siren and flashing siren 9 93code Recording voice message 9 801234 SMS 0 number Phone number 1 number 2 number NOTICE The use of an alarm system is subject to a wide variety of factors which can affect the utility and effectiveness of the alarm system It is important that the user of the alarm system installs the alarm correctly and safely Most importantly do not set the alarm system up directly next to another electrical device SPECIFICATIONS GSM control panel 100 240AC 12DC Stand by current lt 90mA Alarm current lt 200mA Power consumption 0 5Watts Built in lithium battery 1800mA 3 6Volts ADD ON DEVICES T
9. k button If initialisation is successful the RED network LED will flash continually If this does not flash please check the SIM is installed correctly and has credit on it Y ed D 1 ALARM SETUP You have the option of setting up a 10 second pre recorded message on this alarm so that it can play this back to the people it calls when activated We suggest you say something like Dave amp Sue s alarm activated the house the street the town please help As remember the alarm might not just be calling you you may have set it up to call friends and family To record your play back message please input the following commands on the white key pad supplied with the alarm system 9 80 password The default password is 1234 Now facing the GSM alarm panel please speak towards it at a distance of around 12 inches then when you have finished speaking please press the button again to save You will hear a short BEEP from the system to confirm this operation is complete You can setup 6 auto dial phone numbers for the alarm to call when activated To program the first number in the sequence of numbers to call please do as follows on the white programming key pad For example the number we will enter is 0123412345678 1 0123412345678 The alarm will make a short BEEP to confirm the operation is successful To enter the next number you want the alarm to call if the first one is not answered please replac
10. pressing the small eject button inwards It will only fit in one way so please do not force the card in The copper sides of the SIM should point downwards Install your alarms sensors in the required positions that best protect your property Extra sensors are available and can be added at any time please contact us at sales global gadgets com or visit us at www global qadgets com to view the extras that are available You can fit a door contact sensor or magnet on either the fixed part of the frame or the moving part it does not effect the sensors operation PIR are best located in corners of rooms to give best protection but this is down to you to decide what is best 3 Next on the top edge of the alarm system you will find a small switch this is the backup battery switch Please be sure to switch this on This will then give you backup power should the properties power fail The alarm is fitted with a lithium battery so you should get around 72 hours of battery life Lastly please connect the alarm power adaptor to a 13amp socket The green power light will come on and the system will enter into self test mode Once it has completed this the alarm will automatically arm itself The alarm will now initialise and you will here a BEEP sound It will then auto search for a GSM signal from the SIM card This will take around 1 minute to complete Once completed please disarm the system using the remote key fob by pressing the open padloc
11. st have text alert setup for this to work Wireless Strobe Siren Setup If you have purchased the Defender bundle or have added an external strobe siren to your alarm system you will need to do the following to set the wireless strobe siren Please note that the siren has been tested and linked to the wireless sender device already for you 1 First remove the sirens front cover and connect the backup battery You will see the batteries in a green cover and there will be a black and red wire with a white connection block plug this into the socket on the circuit board in the bottom left hand corner You will also find a wire that is not connected at one send do not worry this is the aerial If you have upgraded to the LX siren you will need to remove the screw cover from the front of the siren This can be located at the centre of the siren where the blue plastic joins to the white cover Use a small flat head screwdriver to prise the flap open and remove the screw to gain access Along with the siren is a small white sender device this sends the wireless signal to the strobe siren and must be plugged into the socket on the alarm panel marked Siren If you wish to use both the wireless strobe siren and the supplied wired siren you will need to purchase an audio splitter that will convert the single siren socket into two sockets We do not sell these but they can be bought for around 1 50 3 Attach the siren to its required locat
Download Pdf Manuals
Related Search