STRIPE COMFORT
Contents
1. arabiners in place and not damaged functional User manual available Product identification legible Other OK Blocked 16 17 BORNACK EU DECLARATION OF CONFORMITY CE Conformity Declaration BORNACK The manufacturer or his authorised representative located in the EU BORNACK GmbH amp Co KG Bustadt 39 D 74360 Ilsfeld Germany Hereby declares that the following designated personal protective equipment Safety harness BORNACK STRIPE In the following versions without anchor grommets EN 358 EN 813 STRIPE BASIC STRIPE BASIC CLICK STRIPE BASIC CLICK LIGHT with anchor grommets EN 358 EN 813 and hip pad STRIPE COMFORT STRIPE COMFORT CLICK STRIPE COMFORT CLICK LIGHT meets the requirements of the EC Directive 89 686 EEC and if applicable the Norm EN 361 EN 358 EN 813 which has been harmonised into national law according to Article 8 4 The personal protective equipment e is identical to the PPE which is the subject of the CE model certification No P5 12 03 40506 094 e issued by TUV Product Service GmbH Zertifizierungsstelle CE 0123 Ridlerstr 65 D 80339 Munich Germany is subject to the manufacturing monitoring according to Art 11 Point B of the EC Directive 89 686 EEC monitored by the notified testing institute TUV Produkt Service GmbH Ridlerstr 65 D 80339 Munich Germany 10 July 2012 BORNACK GmbH amp Co KG l2. Klaus Bornack Management Notes 18 19 BORNACK Notes Notes BT BORNACK FALLSTOP Equipment for securing and rescue at heights and depths SAFEPOINT Stationary securing systems for architecture and industry BORNACK GmbH amp Co KG Bustadt 39 74360 Ilsfeld Germany Fon 49 0 7062 26 90 0 0 Fax 49 0 70 62 26 90 0 550 info bornack de www bornack de BORNACK Switzerland Oholten 7 5703 Seon AG Switzerland Fon 41 0 62 886 30 40 Fax 41 0 62 886 30 41 info bornack ch www bornack ch BORNACK Subject to technical changes Reprinting or duplication even excerpts are only permitted with written consent Status 10 2013 GAL No 000 012 ebo
3. come into contact with aggressive substances e g oils grease acids chemicals Store the personal protection equipment in the device case or strap bag TRANSPORT Transport the personal protection equipment protected in a device case or strap bag 14 15 BORNACK TEST CARD FOR ANNUAL MONITORING The test card must be completed in full by Type Product name the expert during the annual inspection Manufactured on This test card does not claim to cover all test criteria and does not relieve the expert from Serial no his decision about the overall condition Purchase date Manufacturer BORNACK GmbH amp Co KG Date of first use info bornack de www bornack de Life span at the latest Application range Next Date Signature inspection Reason for inspection Year 1 Year 2 Year 3 Year 4 Year 5 Year 6 Year 7 Year 8 Year 9 Year 10 TEST CARD FOR ANNUAL MONITORING Please complete X Year Year Year Year Year Year Year Year Year Year 10 Strap undamaged Seams undamaged Strap ends secured sewn down Fixture parts complete and undamaged No deformation of metal parts Plastic parts complete and undamaged CLICK BUCKLE EASY GLIDE not deformed and smooth running Harness fasteners CLICK not deformed soiled functional
4. expert or a workshop authorised in writing by BORNACK This must be documented in the test card The rope protection arrester harness is part of the personal protection equipment to prevent falling and should be assigned to a specific person The personal protection equipment may only be used by qualified staff that are familiar with the material They must be proficient in handling the personal protection equipment and must have been briefed about the possible risks associated with its use In accordance with the accident prevention guidelines UVV the users of fall protection equipment Category 3 must attend a theoretical training course and a practical training course Make use of the training competence of the BORNACK training centres hotline bornack de Accessories from other manufacturers may only be used if approved by BORNACK and may not impair the function and safety of the protection equipment Clothing and shoes must be suitable for the task at hand and the weather conditions Only use the equipment if you are fully fit Health impairments can jeopardise the safety of the user when working at heights or depths Protect personal protection equipment during storing use and transportation against the effects of heat e g welding flames or sparks burning cigarettes and chemicals e g acids alkalis oils and mechanical effects e g sharp edges Before starting work the responsible pe
5. the leg straps and chest harnesses STRIPE COMFORT Back loading fasteners made of steel STRIPE COMFORT CLICK CLICK fasteners made of stainless steel STRIPE COMFORT CLICK LIGHT CLICK fasteners made of aluminium Strap end storage Comfort padding on hip Universal size XS XL Equipment bag for storage and transport ACCESSORIES Special karabiner HEART LIGHT BRIEF DESCRIPTION PRODUCT IDENTIFICATION The following is attached to the product Logo Product name variant Product type Size Article No Charge year of production Serial No Useful load EN standards QR Code CE symbol Contact _ Y BORNACK STRIPE comfort click Auffang Rettungsgurt Fullbody harness Size Uni Size Art Nr 311 204 Charge mm JJ 0000000 C 0123 www bornack de Read observe the user manual USEFUL LOAD The maximum number of users is 1 person The arrester harnesses of the STRIPE COMFORT series were tested and certified for application cases in which the energy absorbing connecting equipment e g in compliance with EN 354 and EN 355 directs a maximum impact force of 6 kN into the arresting D rings and arresting loops If users weigh more than the standard defined 100 kg the physiological suitability must be explicitly verified Connecting equipment suitable for the weight of the user must be used that despite the weight ofthe user does not exceed an impact force
6. Wy BORNACK ore COMFORT BORNACK STRIPE COMFORT STRIPE COMFORT CLICK STRIPE COMFORT CLICK LIGHT arresting rescue harness Subject to technical changes BRIEF DESCRIPTION INTENDED USE The arrester harnesses of the STRIPE COMFORT series serve exclusively to protect the wearer from falling in fall hazard areas e g ladders scaffolding roofs platforms in hazard zones when abseiling or rappelling application temperature 20 C to 80 C STRIPE COMFORT CLICK VA suitable for seawater areas and similar STRIPE COMFORT CLICK LIGHT alu not suitable in explosive areas Recommended connecting equipment Arrester device in compliance with EN 353 2 or EN 353 1 Energy absorber connecting equipment in compliance with EN 354 or EN 355 Height securing device in compliance with EN 360 All other uses are deemed improper The company BORNACK will not be liable for any ensuing damages The user bears the sole risk USE Arresting Restraining on the fall edge Rescuing active and passive Climbing in vertical fall arrest system EN 353 1 Positioning FEATURES e Rear arresting D ring Front arresting loops Side positioning D rings Ventral attachment D ring Very strong polyester strap Force flow optimised CNC seam patterns CLICK BUCKLE EASY GLIDE made of steel for size adjustment of the shoulder harnesses Harness fasteners with length adjustment of
7. astener and its lock functional BORNACK STRIPE COMFORT IN USE PREPARATION A A Lift the arrester harness on the rear arresting 3 D ring All harness fasteners need to be open a Harness must hang freely and may not be twisted B Put on the arrester harness like a jacket Arms through the shoulder harness Close the chest harness CAUTION If the front arresting loops are used both loops must be placed jointly on the karabiner in compliance with EN 362 C Close the abdominal belt Please observe the instructions about closing the abdominal belt depending on belt variant on page 10 11 D Adjust the shoulder harnesses Adjust the harness to the body so that the seat harness is positioned below your bottom Close the leg loops Pull the leg loops individually between your legs and then close Tighten the harness so that you can place one hand between the strap and your leg Check the fit of the arrester harness The shoulder harness and leg straps should be flush to the body but not too tight The shoulder harness straps should be set to the same length The rear arresting D ring must sit centrally between your shoulder blades If necessary suspend yourself in the arrester harness to test If necessary readjust the harness fitting STRIPE COMFORT IN USE Roll up the excess strap end using the strap end storage feature and secure CAUTION Observe roll up di
8. e abdominal belts of the STRIPE COMFORT CLICK LIGHT EThread the strap end of the abdominal belt through the rectangular frame on the left end of the padding Feed through the ventral attachment D ring back to the buckle F Open the click slide with your thumb and index finger Feed the abdominal belt strap through the back of the click mechanism arrow marking 1 on the buckle Release the click slide To adjust pull on the loose strap end into the required position Then feed the strap through opening 2 see arrow marking To release the buckle tilt it by 180 and pull the click slide with your thumb and index finder from behind STRAP END STORAGE The strap end storage device serves secure storage of the free strap ends Wind the strap outwards around the storage clip until approx cm from the strap fastener or the buckle Guide the elastic band behind the adjusted strap and place the plastic stopper into the groove CAUTION Observe roll up direction A strap end that is rolled up incorrectly will restrict the clamp effect of the click buckle BORNACK 12 13 GENERAL INFORMATION APPROVAL Conformity with the EC Directive 89 686 EEC Personal protective equipment Type testing and production monitoring by T V S d Product Service GmbH Ridlerstr 65 80339 Munich CE 0123 Quality management system certified to DIN EN ISO 9001 Production monit
9. h EN 355 354 and sliding arrester devices including mobile guides EN 353 2 e g RS SO5 10 11 BORNACK FASTENERS IN USE CLICK BUCKLE EASY GLIDE This buckle only serves to adjust the length of the straps Tilt the buckle Pull the open strap to tighten until the required position is reached Tighten To release loosen the buckle tilt and then pull it When the buckle is let go the strap position is maintained Release BACK LOADING FASTENER The fastener serves to close and adjust the leg straps Insert the backloading frame diagonally and longitudinally through the large frame Ensure that the strap end is at the top Slightly tilt the frame of the buckle Pull the respective strap until the required position is reached When the strap is let go the position is maintained CLICK FASTENER CLICK LIGHT FASTENER This fastener serves to close and adjust the leg straps or the abdominal belt Using your thumbs and index fingers on both hands slightly squeeze the buckle and exert pressure on the lock wings If the CLICK fastener is taut it cannot be opened To tighten pull on the loose strap until the required position is reached To release the setting slightly tilt the buckle and pull on the strap FASTENERS amp STRAP END STORAGE IN USE SLIDE CLICK BUCKLE This fastener serves to adjust th
10. ntact the email hotline hotline bornack de If the personal protection equipment comes into contact with saltwater keep it wet until it can be rinsed with distilled water GENERAL INFORMATION LIFE SPAN Recommendations for the use of personal protection equipment in industrial environments Maximum storage period before using for the first time Harnesses up to 3 years In optimum storage conditions e g protected from light dry normal climate Maximum usage period after being used for the first time Harnesses up to 10 years Regular or intensive use and or in extreme conditions e g sharp edges and chemical influences will reduce the usage period The company owner must ensure and take this into account in the risk analysis of the workplace The company owner must ensure compliance with the maximum usage period by documenting first time use in the test card or the rope log For more information please see the BORNACK brochure Life span of textile personal protection equipment components at www bornack de REPAIRS Only the manufacturer may carry out repairs STORAGE Dry damp personal protection equipment before storing Store away from light in a dry place Do not store personal protection equipment close to radiators Permanent temperatures of over 50 C havea negative impact on the strength of the textile material and will reduce the life span Do not allow personal protection equipment to
11. of 6 kN If this is guaranteed and the securing chain is not overloaded the STRIPE harness may be used by users weighing over 100 kg 415 BORNACK STRIPE COMFORT STRIPE COMFORT CLICK Rear arresting D ring NY lt Shoulder harness Identification label pouch lt Front anchorage loop Chest harness Sy lt Strap end storage optional elastic loop EASY GLIDE gt A for affixing click buckle P lt Side positioning Abdominal belt D rings slide click buckle Ventral attachment Fastener dependingon gt D ring model back loading fastener CLICK fastener Seat harness Leg loops STRIPE COMFORT CLICK LIGHT Rear arresting D ring lt Shoulder harness Identification label pouch Front anchorage loop Chest harness Strap end storage optional elastic loop EASY GLUDE gt for affixing click buckle lt Side positioning Abdominal belt D rings CLICK LIGHT fastener Ventral attachment Fastener depending on D ring model CLICK LIGHT fastener Seat harness Leg loops BORNACK SAFETY INSTRUCTIONS There is a risk to life if these safety instructions are not observed The personal protection equipment may no longer be used even in the case of very minor faults Damaged fall stressed dubious personal protection equipment or safety devices must be immediately withdrawn and not used The equipment may only be inspected by an
12. oring by notified body Category Ill REGULAR INSPECTIONS This personal protection equipment must be inspected at least once a year by an expert The result must be documented in the test card at the end of this user manual SALES The dealer must ensure that the user manual is supplied in the applicable national language The respective translation must be authorised by BORNACK SERVICE If you have any questions about safe use of this personal protection equipment or any other services provided by BORNACK please contact hotline bornack de We will be happy to help Expert inspections Risk analysis Rescue plans Training courses MAINTENANCE Keep mobile parts e g on karabiners click fasteners and other devices clean If necessary carefully oil joints with resin free sewing machine oil Maintenance may only be performed by trained specialists The instructions in this user manual and any instructions in the maintenance manual must be strictly observed Protective equipment that is well looked after will last longer CLEANING Dry damp personal protection equipment in the air not on artificial heat sources Dry metal components with cloths Clean soiled textile components e g arrester harnesses and ropes with lukewarm water and a little detergent for delicates Then rinse thoroughly and allow to dry in the air No other cleaning agents may be used For information about disinfection please co
13. rection A strap end that is rolled up incorrectly will restrict the clamp effect of the click buckle CLIMBING WITH VERTICAL FALL ARREST EQUIPMENT Application with sliding arrester devices on a fixed guide EN 353 1 The two combined front arresting loops must be used as the primary attachment type for sliding arrester devices in compliance with EN 361 If other vertical fall arrest runners than the RS So5 or RS Hos that have been approved by BORNACK are used the user must carry out a risk assessment compatibility check for the use of the ventral attachment D ring tested in compliance with EN 813 section 5 3 and section 5 4 Use with sliding arrester devices on mobile guide EN 353 2 Sliding arrester devices on mobile guides must be attached on the two combined front arresting loops or the reararresting D ring When instructing users special attention should be drawn to the potentially fatal risks of foreseeable wrong operation e g sliding down ladders by manipulating the sliding arrester device including the fixed guide ladder surfing negligent adornment of the harness Special official local and statutory information and any instructions issued by the accident insurance institutions should also be observed The ventral attachment D ring may not be used with rescue or rescue lifting equipment in compliance with EN 341 EN 1496 rope adjustment devices in compliance with EN12841 fall arresters in compliance wit
14. rson must draw up a plan of rescue measures that defines how to rescue casualties quickly and safely and ensures first aid measures Casualties must be rescued within 10 to 30 minutes BORNACK can help you draw up tailor made rescue plans in specific training courses hotline bornack de The local safety guidelines e g in Germany the guidelines issued by the professional associations BGR 198 and BGR 199 and the accident prevention guidelines for the specific industry UVV must be observed INFORMATION BEFORE USE Always check every time before using A If during the inspection even the slightest of faults is detected this protection equipment may not be used Faulty protection equipment components may only be tested and repaired in a workshop authorised by the company BORNACK The compatibility and use of the ventral attachment D ring must be checked against the user manual for the arrester device on a fixed guide that is to be used For more information please see page 9 VISUAL INSPECTION Check that the equipment is undamaged and complete Are all seams complete and undamaged Can you see or feel any damage in the textile components Are there any signs of damage to the fittings D rings buckles karabiners Are they bent Is the product identification legible Was the last expert inspection less than 1year ago Do the fasteners run smoothly Is the karabiner f
Download Pdf Manuals
Related Search