MODEL D7400 Online User Manual
Contents
1. DYNATRON 2L Simply The best Incar Security MODEL D7400 Online User Manual alar d Sec Cunty j 1 nc 3 RAATI 3 7 07 2008 The D7400 have been tested and meets AS NZS 4601 2003 and AS NZS 3749 1 2003 Part B ARMING AND DISARMING To arm or disarm the system press the larger button on the remote control Arming the system is accompanied by two flashes from the indicators and one flash for disarming If the horn confirmation option is enabled not recommended the system will also sound the horn twice for arming and once for disarming ARMING AND DISARMING TRANSPONDER The Transponder is able to communicate with the module via an aerial loop inside the steering column and where the immobiliser has automatically disabled the vehicle by turning the ignition key to the ON position the transponder will cancel the immobilisers and allow the vehicle to start normally In cases where the remote battery is very low the transponder MAY have enough power to disable both the Alarm and the Immobilisers after entering the vehicle by manually unlocking the doors to gain entry PANIC If the primary button on the remote control is pressed and held down for more than two seconds the system will go into a panic mode In this mode the indicators will flash and the horn will sound The panic mode will continue for thirty seconds If you wish to cancel the panic signal before the thirty seconds then simply press the larger button of the rem2. RON NZ Ltd P O Box 302 384 North Harbour Auckland New Zealand Subject to the conditions stated below to be free from manufacturing defects and faulty material within the warranty period stated below CONDITIONS That the warranty registration has been completed in full at the time of purchase and or installation and is produced when warranty service is sought The warranty does not cover general maintenance such as cleaning of bonnet switches door switches light switches etc nor replacement of consumable items such as pilot lamps or transmitter batteries Should a product defect become apparent within the warranty period DYNATRON NZ LTD will repair the product free of charge for parts only Labour to remove and install the serviced product will be the responsibility of the original installer and their prescribed labour warranty terms and conditions This is a return to base warranty and should a mobile service be required a call out charge will apply Ihi hall Land void it The product has been repaired by any other person other than by an authorized DYNATRON service centre The product has been altered or tampered with in any way or the serial number altered defaced or removed The defect has been caused by negligence by the owner or their agent The product has not been operated correctly installed by an authorized DYNATRON installer or has been subjected to misuse or undue wear and tear 5 The control module is dam
3. age Optional Each zone will trigger a maximum of three times per arm cycle Once a zone has sounded the horn three times it is ignored until the next time the system is armed At no time does the immobiliser disarm BATTERY REPLACEMENT Using a small Phillips head screwdriver remove the three screws at the back of the remote and carefully separate the two body housings taking take care not to disturb the circuit board Remove the old battery whilst paying attention to t he orientation of the positive and negative terminals Insert new battery in identical fashion to the original and re assemble remote Replace screws and test remote control by pressing main button For further information please contact your local DYNATRON service centre Remote battery type 12V 27a PROBLEM SOLVING System won t activate when the door is opened Make sure you have used the remote to set the system It will not trigger if the system has auto armed Make certain the system is activated LED should be flashing on the dashboard Make sure that the interior dome light has not been left in the permanently ON position Make sure that you have allowed at least 30 seconds after setting the system before opening the door System won t activate or deactivate LED won t flash or extinguish Make sure that ignition switch is in the OFF position Make sure the vehicle battery is not flat Try your spare remote transmitter unit The remote fails to opera
4. aged by water AWN THE WARRANTY DOES NOT COVER THE FOLLOWING COSTS Transport of the product to and from DYNATRON service centres Insurance of the product in transit to or from the DYNATRON service centres Cost of any service call where the product is found by Dynatron to be in good working order DISCLAIMER Dynatron systems have all been tested and approved to Australian and New Zealand Standards an d only Dynatron Authorised Installers have been given the information to install your system correctly to those same standards Dynatron NZ Limited will accept no liability for any independent installation of this product its performance or operation We believe that the responsibility for a system performing according to published and verifiable standards rests primarily with you as the owner and end user Should you have any concerns about your Dynatron system then please call us at Dynatron direct during working hours toll free 0800 508 904 and speak to Customer Services or one of our Technical team We are here to help and we will see that you get Simply The best Incar Security for your car PLEASE COMPLETE DETAILS BELOW AND REGISTER YOUR DYNATRON It is very important that your DYNATRON product details are recorded below The units Serial Number is recorded in our secure database which is directly associated with the Emergency Override PIN and it is this PIN Number that will enable your security system to be overridden If in the unl
5. contact vendor for more Information The system is featured with selectable options ANTIHIJACK Locks the doors when the ignition is turned on so long as all the doors are closed Also unlocks the doors when the ignition is turned off DOME LIGHT UPON DISARM llluminates the dome light of the vehicle for thirty seconds when the system is disarmed The light will extinguish if ignition switch is turned to the on position HORN OUTPUT Determines whether the 30 seconds of alarm trigger output on the horn wire is constant or pulsed ARM DISARM CONFIRMATION Allows the system to arm in silent mode The standard indicator flashes will accompany each arm disarm command but the horn will remain silent This option has no effect on the triggered sound e 120 SEC RELOCK Enables the auto relock feature The doors will automatically relock when a the vehicle has been disarmed by remote control b The doors remain closed for more than 120 seconds OPEN DOOR WARNING Produces a warning in the form of multiple chirps from the horn when arming with the door open DIAGNOSTICS Whenever the alarm system is triggered the memory of the module will be automatically updated with the number of the zone responsible The report will be displayed upon the next disarm command Both the indicators and status LED will flash a number of times The table below describes the number for each zone ZONE NUMBER ZONE NAME 1 Bonnet 2 Aux 3 Doors 4 Glass break
6. ikely event that you need our Free 24hr 0800 Assist and you can provide the serial number then we will be more than likely able to start your car over the phone REMEMBER A THREE YEAR WARRANTY ON MODULE APPLIES ONLY IF THE INSTALLATION IS PERFORMED BY AN AUTHORIZED DYNATRON INSTALLER 12 MONTHS ON REMOTES AND ACCESSORIES OWNERS DETAILS OWNER NAME DYNATRON MODEL MODULE SERIAL NUMBER VEHICLE REGISTRATION NUMBER VEHICLE MAKE VEHICLE MODEL YEAR INSTALLER DETAILS INSTALLER COMPANY NAME _ INSTALLER NAME DATE INSTALLED PHONE US ON 0800 508 904 TO REGISTER YOUR DYNATRON THIS IS AN ONLINE USER MANUAL COPY THE WARRANTY APPLIES FROM THE DATE OF ORIGINAL INSTALLATION OR IF UNKNOWN FROM THE DATE OF MANUFACTURE ON THE DYNATRON MODULE DYNATRON ACCESSORIES Dynatron offers a full range of sensors each one designed for a specific application r r Microwave Sensor Glassbreak Sensor Tilt Sensor Shock Sensors Ultrasonic Sensor Battery backed up Siren DYNATRON wD me NAE NN YU IMAL nea A GPS TRACKING SYSTEM Dynatrace GPS Tracking Systems Door Motors
7. ote control again BOOT RELEASE OPTIONAL Disarm the system by pressing the top button on the remote control Then press the lower button on the remote control and keep it depressed until the boot releases This will take about 3 seconds This function will only operate if the vehicle is equipped with an electrical boot release and it is connected AUTO ARMING The system is set to automatically immobilize the vehicle The engine will be immobilized within 30 40 seconds after the ignition has been turned off If turned off with the remote control the system will re immobilize itself within the same time period ENGINE IMMOBILISATION When the system is armed the engine is also immobilized The independent normally open circuits of immobilization ensure the engine is starved of either fuel or spark Immobilization points vary from vehicle to vehicle common engine kill places include fuel injection fuel pump fuel cut off solenoids main ignition feed low tension distributor supplies and starter motor solenoids etc INTRUSION DETECTION The D3400 is equipped with three zones of protection doors bonnet amp auxiliary Each zone can be triggered a maximum of three times after arming When a zone is triggered the horn will sound for 30 seconds and the indicators will flash for one minute The horn will reset for five seconds after each 30 second trigger period before sounding due to subsequent triggers OPTIONS SELECTABLE OPTIONS please
8. te If the remote fails to operate and the LED does not light up when the button is pressed then change the battery As above OVERRIDE The system can be overridden by means of a Personal Identification Number PIN Every unit has it s own PIN This PIN is issued with every system by means of a credit card sized PIN card Do not lose this card Do not leave it in your vehicle Do not tell anyone your PINnumber Do store the PIN card in asafe and confidential place Storing the PIN number in a secure place in your cell phone is an ideal way to store the number OVERRIDE PROCEDURE 1 Insert the ignition key into the ignition switch and turn to the ON position The blue or red status LED mounted on the dash will glow constantly 2 Turn the ignition key back to the ACC position the status LED will begin to flash slowly Count the number of flashes for the first digit in the PIN of the alarm immobiliser Return the key to the ON position when the correct number is counted 3 Repeat step 2 for the remaining digits in the PIN When all four digits are entered the indicators will flash once the system will then disarm Please Note Any digit marked 0 indicates 10 flashes NB gt If the engine is not started within 40 seconds of over riding the alarm immobiliser willimmobilize the engine It is necessary to enter the PIN each time the engine is turned off andthe system has auto immobilized WARRANTY This product is warranted by DYNAT
Download Pdf Manuals
Related Search