ASA-30 - Jem & Fix
Contents
1. er nu registreret i kontrolpanelet hvis du h rer 3 bip er sirenen allerede tilsluttet kontrolpanelet Tryk p Tilslutningsknappen p sirenen igen for at afslutte tilslutningstilstanden Bem rk Undlad at udl se alarmen med en sensor mens du registrerer sirenen i kontrolpanelet Test Tryk p knappen Arm Aktiv r p fjernbetjeningen B de kontrolpanelets indbyggede sirene og ASA 30 bipper forbindelsen er oprettet Hvis du ikke h rer noget bip er forbindelsen ikke oprettet og du skal fors ge at registrere sirenen forfra Anvendelse som uafh ngigt alarmsystem F r du kan anvende ASA 30 som uafh ngigt alarmsystem skal den forbindes til en fjernbetjening eller andet udstyr f eks en bev gelsessensor eller en d r vindueskontakt N r systemet er aktiveret vil sirenen lyde og LED lysene t nde hvis en sensor udl ses Tilslutning til en fjernbetjening Tryk p sirenens Tilslutningsknap Sirenen bipper n gang og LED lysene t nder sirenen er nu i tilslutningstilstand Tryk p en hvilken som helst knap p fjernbetjeningen Du h rer t bip Sirenen er nu registreret i fjernbetjeningen hvis du h rer 3 bip er sirenen allerede tilsluttet fjernbetjeningen Tilslutning til en tr dl s sensor Tryk p sirenens Tilslutningsknap Sirenen bipper n gang og LED lysene t nder sirenen er nu i tilslutningstilstand Udl s sensoren f eks ved at g ind foran sensoren hvis du vil tilslutte en bev ge2. siren switches to Home Mode and the strobe light turns into a night lamp Press the Stay button twice then the Arm button once the siren is in monitoring mode with night lamp on Press the Disarm button the siren is disarmed and the LED lights switch off Specifications Power supply 220V Volume 90dB Backup battery 4 2V 600mA Lithium Static current lt 13mA Alarm current lt 300mA Radio frequency 315MHz or 433MHz 75KH2 Housing material ABS plastic Operating conditions Temperature 10 C 55 C Relative Humidity lt 80 non condensing Dimensions 81 x 80 x 76 mm Standards ALL RIGHTS RESERVED COPYRIGHT DENVER ELECTRONICS A S DENVER www denver electronics cor C pi Electric and electronic equipment and included batteries contains materials components and substances that can be hazardous to your health and the environment if the waste material discarded electric and electronic equipment and batteries is not handled correctly Electric and electronic equipment and batteries is marked with the crossed out trash can symbol seen below This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other household waste but should be disposed of separately As the end user it is important that you submit your used batteries to the appropriate and designated facility In this manner you make sure that the batteries are rec
3. window contact When the system is armed if a sensor is triggered the siren will ring out and the LED lights will turn on Connect a remote control Press the Connect button on the siren The siren beeps once and the LEDs light up the siren is now in Connection Mode Press any button on the remote control You hear one beep the remote control has been connected to the siren successfully if you hear 3 beeps the remote control has already been connected Connect a wireless sensor Press the Connect button on the siren The siren beeps once and the LEDs light up the siren is now in Connection Mode Trigger the sensor e g walk in front of the sensor if you want to connect a motion detector You hear one beep the accessory has been connected to the siren successfully if you hear 3 beeps the accessory has already been connected The siren supports up to 10 remote controls and 10 wireless detectors Test a Test the connection to a remote control Press the Arm button on the remote control The siren beeps once the connection of the remote control is successful If not the connection has failed try registering the remote control again b Test the connection to a wireless sensor Arm the system Trigger the sensor e g walk in front of the sensor if you have connected a motion detector The siren rings out the connection of the sensor is successful If not the connection has failed try registering the sensor
4. DENVER denver electronics com ASA 30 Indoor Siren Indend rs Sirene ED Features The ASA 30 can be used either as an additional siren connected to your alarm system or as an independent siren connected to a remote control and or wireless detectors Wireless connection for an easy installation Radio frequency security of the accessories more than one million of codes combinations Simplified connection to accessories Can be connected to all of eTiger Secual accessories Built in 4 2V 600 mAh lithium batteries 8 hour battery life in standby mode Box Content 1 x ASA 30 1 x User Manual Layout General information The ASA 30 is powered by its built in AC 220V plug Several ASA 30 can be installed throughout your home and connected to your alarm system When the alarm of your system is triggered the ASA 30 rings out and its LEDs switch on The ASA 30 can also be used as a standalone siren and can be connected to wireless sensors and or to a remote control Power on off Power on The siren is powered off as per default settings Plug the siren to a 220V socket and press the Power button on the siren You hear a long beep the siren is on You can also turn the siren on by long pressing 6 seconds the Power button on the siren Enter Setup Mode Power off Enter Setup Mode by pressing the Power button once Press again the Power button for 6 seconds to turn the siren off Siren and light indic
5. again Clear all accessories Press the Connect button on the siren for 6 seconds until you hear two beeps The LEDs blink twice all the accessories connected to the siren have been cleared Entry Exit Delay A delay before activation can be set for the siren ifthe sensor is assigned to the Delay Zone If the Entry Exit Delay is activated the siren beeps once every second until the system is armed during the period of delay set If one of your system s sensors triggers the alarm the ringing out of the siren will be delayed accordingly The name of the Delay Zone and the connection process may vary depending on models Refer to the user manual of your alarm system for more information Set up the delay Enter Setup Mode by pressing the power button once Press the power button again once to set the delay to 10 seconds twice to set the delay to 20 seconds three times to set the delay to 30 seconds four times to deactivate the delay Default setting no delay The delay will be effective only if the sensors have been assigned to the Delay Zone To assign a sensor to the Delay Zone open its cover and move the jumpers on the circuit board according to the opposite drawing For more information refer to the manual of your alarm system Night Lamp mode When used as a standalone alarm system the ASA 30 can also be used as an LED night lamp Press the Stay button on the remote control twice the
6. ations When arming the system The siren beeps once the LED lights blink once and switch on When disarming the system The siren beeps twice the LED lights blink twice and turn off When armed disarmed in Mute Mode from the control panel The siren does not beep the LED lights do not blink Use as an additional siren Ifthe siren is used as an additional siren it must be registered to your alarm s control panel Ifthe alarm is triggered the ASA 30 will ring out and its LED lights will turn on Register the ASA 30 in the control panel Press the Connect button on the siren The siren beeps once and the LEDs light up the siren is now in Connection Mode Press the SOS or Arm button on the control panel of your alarm system You hear one beep the siren has been registered in the control panel successfully if you hear 3 beeps the siren has already been connected Press the Connect button again on the siren to exit the Connection Mode Note Do not trigger an alarm with a sensor when registering the siren in the control panel Test Press the Arm button on the remote control Both the built in siren of the control panel and the ASA 30 beep the connection is successful If not the connection has failed try registering the siren again Use as a standalone alarm system Before using the ASA 30 as a standalone alarm system it must be connected to a remote control or an accessory e g motion detector door
7. atur 100C 550C Relativ Luftfugtighed lt 80 ikke kondenserende Ydre mal 81 x 80 x 76 mm Standarder ALLE RETTIGHEDER RESERVERET COPYRIGHT DENVER ELECTRONICS A S DENVER www denver electronics cor CE Elektrisk og elektronisk udstyr samt medf lgende batterier indeholder materialer komponenter og stoffer der kan v re skadelige for menneskers sundhed og for milj et hvis affaldet kasseret elektrisk og elektronisk udstyr og batterier ikke h ndteres korrekt Elektrisk og elektronisk udstyr og batterier er m rket med nedenst ende overkrydsede skraldespand Den symboliserer at elektrisk og elektronisk udstyr og batterier ikke m bortskaffes sammen med usorteret husholdningsaffald men skal indsamles s rskilt Som slutbruger er det vigtigt at du afleverer dine udtjente batterier til de ordninger der er etablerede P denne m de er du med til at sikre at batterierne genanvendes i overensstemmelse med lovgivningen og ikke un digt belaster milj et Alle kommuner har etableret indsamlingsordninger hvor kasseret elektrisk og elektronisk udstyr samt b rbare batterier gratis kan afleveres af borgerne p genbrugsstationer og andre indsamlingssteder eller bliver afhentet direkte fra husholdningerne N rmere information kan f s hos kommunens tekniske forvaltning Importeret af DENVER ELECTRONICS A S Stavneagervej 22 DK 8250 Egaa Danmark www facebook com denverelectronics DENVER denver elect
8. il dit alarmsystem Hvis din alarm udl ses starter ASA 30 sirenen og dens LED strobelys t nder ASA 30 kan ogs anvendes som uafh ngig sirene og kan forbindes til tr dl se sensorer og eller til en fjernbetjening T nd Sluk T nde Som standard er sirenen slukket S t sirenen i en 220V stikkontakt og tryk p dens Powerknap Du h rer et langt bip sirenen er t ndt Du kan ogs t nde sirenen ved at trykke langt 6 sekunder p dens Powerknap bne ops tningen Slukke ben ops tningen ved at trykke n gang p Powerknappen Tryk og hold knappen Power i 6 sekunder n r du vil slukke sirenen Sirene og lysindikatorer N r du aktiverer systemet Sirenen bipper n gang LED lysene blinker n gang og lyser derefter konstant N r du deaktiverer systemet Sirenen bipper to gange LED lysene blinker to gange og slukker s N r sirenen er aktiveret deaktiveret i Lydl s tilstand fra kontrolpanelet Sirenen bipper ikke LED lysene blinker ikke Anvendelse som ekstra sirene Hvis sirenen skal anvendes som ekstra sirene skal den registreres i dit alarmsystems kontrolpanel Hvis alarmen udl ses lyder ASA 30 og dens LED lys t nder S dan registreres ASA 30 i kontrolpanelet Tryk p knappen Tilslut p sirenen Sirenen bipper n gang og LED lysene t nder sirenen er nu i tilslutningstilstand Tryk p knappen SOS eller Arm Aktiv r p dit alarmsystems kontrolpanel Du h rer t bip sirenen
9. lsessensor Du h rer t bip Sirenen er nu registreret i sensoren hvis du h rer 3 bip er sirenen allerede tilsluttet sensoren Sirenen underst tter op til 10 fjernbetjeninger og 10 tr dl se sensorer Test a Test af forbindelsen til en fjernbetjening Tryk p knappen Arm Aktiv r p fjernbetjeningen Sirenen bipper n gang forbindelsen til fjernbetjeningen er oprettet Hvis du ikke h rer noget bip er forbindelsen ikke oprettet og du skal fors ge at registrere sirenen i fjernbetjeningen igen b Test af forbindelsen til en tr dl s sensor Aktiv r systemet Udl s sensoren f eks ved at g ind foran sensoren hvis du har tilsluttet en bev gelsessensor Sirenen lyder forbindelsen til sensoren er oprettet Hvis du ikke h rer noget bip er forbindelsen ikke oprettet og du skal fors ge at registrere sirenen i sensoren igen Slette alt tilbeh r Tryk p Tilslutningsknappen p sirenen og hold den inde i 6 sekunder indtil du h rer to bip LED lysene blinker to gange alt tilbeh r der var tilsluttet sirenen er blevet slettet Forsinkelse ved ind og udgang Du kan inds tte en forsinkelse inden sirenen aktiveres hvis sensoren er allokeret til Enkelt Forsinkelseszone Hvis en forsinkelse ved ind udgang er aktiveret bipper sirenen n gang i sekundet i den valgte forsinkelsesperiode n r systemet er blevet aktiveret Hvis en af systemets sensorer udl ser alarmen vil sirenen lyde med en tilsvare
10. nde forsinkelse Ops tning af forsinkelse ben ops tningen ved at trykke n gang p Powerknappen Tryk p knappen Power igen n gang for at inds tte en forsinkelse p 10 sekunder to gange for at inds tte en forsinkelse p 20 sekunder tre gange for at inds tte en forsinkelse p 30 sekunder fire gange for at deaktivere forsinkelse Standardindstilling ingen forsinkelse Forsinkelsen tr der kun i kraft hvis sensorerne er allokeret til Enkelt Forsinkelseszone Hvis du vil allokere en sensor til Enkelt Forsinkelseszone skal du bne dens d ksel og flytte jumperne p kredsl bet i overensstemmelse med tegningen til h jre Yderligere oplysninger finder du i vejledningen til dit alarmsystem Natlystilstand Hvis du anvender ASA 30 som uafh ngigt alarmsystem kan den samtidig anvendes som LED natlys Tryk to gange pa knappen Stay pa fjernbetjeningen sirenen skifter til Hjemmetilstand og strobelyset bliver til en natlampe Tryk to gange p knappen Stay og dern st n gang p knappen Arm Aktiv r sirenen skifter til overvagningstilstand med natlyset t ndt Tryk p knappen Disarm Deaktiv r sirenen deaktiveres og LED lysene slukker Specifikationer Str mforsyning 220V Lydstyrke 90dB Back up batteri 4 2V 600 mA Lithium Hvilestr m lt 13 mA Alarmstr m lt 300 mA Radiofrekvens 315 MHz eller 433 MHz 75 KHz Hus ABS plast Driftsforhold Temper
11. ronics com
12. ycled in accordance with legislature and will not harm the environment All cities have established collection points where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites or be collected from the households Additional information is available at the technical department of your city Importer DENVER ELECTRONICS A S Stavneagervej 22 DK 8250 Egaa Denmark www facebook com denverelectronics Hereby Inter Sales A S declares that this product HAS 120 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC A copy of the Declaration of conformity may be obtained at Inter Sales A S Stavneagervej 22 DK 8250 Egaa Denmark DEN Features ASA 30 kan anvendes enten som en ekstra sirene tilsluttet dit alarmsystem eller som en uafh ngig sirene forbundet til en fjernbetjening og eller tr dl se detektorer Tr dl s tilslutning for nem installation Radiofrekvenssikkerhed p alle enheder mere end n million kodekombinationer Enkel tilslutning til enheder Kan forbindes til alle Denver alarmenheder Indbyggede 4 2V 600 mAh lithiumbatterier 8 timers batterilevetid pa standby Indholdet i sken 1 x ASA 30 1 x Brugermanual Oversigt Generelle oplysninger ASA 30 drives via det indbyggede 220V stik Du kan installere en r kke ASA 30 sirener i dit hjem og forbinde dem t
Download Pdf Manuals
Related Search