AX3 Manual
Contents
1. is not charging If the status LED is flashing red or alternating between red and blue make sure the Lightdrop is powered off and the ambient temperature is below 40 C If it has been charging in a warmer environment before it may take longer to cool down If the Indicator LED is not flashing at all it is not connected correctly If it still not charging consult your Astera Service Center Charging is very slow Check the color of the Status LED If it is red or flashing yellow move the light into a colder environment My Lightdrop will not pair with my Lumen Radio Transmitter It may be that your Lightdrop is already paired with another transmitter Start by doing a FACTORY RESET of your Lightdrop in order to unpair it from CRMX devices then try re pairing If it still cannot be paired it may be that your transmitter is faulty and you should consult your Astera Service Center or contact Lumen Radio support Safety gt PP EPPH Before you operate this device read the manual carefully Keep in mind that this manual cannot address all possible dangers and environments Please use your own caution when operating Do not operate the device in areas of temperature conditions or under direct sunlight It will cause abnormal function or damage the product Only qualified personnel may repair this product Do not open the product housing A rechargeable battery is built into this device Please avoid bumping or p2. x46 Wallwash amp 32 Flood Diffusor Troubleshooting How can I see if My Lightdrop is on or off Tap the ON OFF button and if it displays the battery status above the fixture is on My Lightdrop will not start up The battery may be empty Connect it to the AC and try again If there is still no power consult your Astera Service Center My Lightdrop starts up but the LEDs do not emit light The fixture could be set to BLACKOUT mode or set to display black color If set to BLACKOUT use the remote control to adjust the intensity or color If this does not solve the problem do a FACTORY RESET to wipe all settings My Lightdrop is not working correctly it does not display the color or effect chosen The fixture may still be operating under a previous setting Do a FACTORY RESET to completely wipe all settings After completing a Factory Reset my Lightdrop still cannot be controlled Make sure the RADIO PIN of the fixture and controller are the same If it still cannot be controlled consult your Astera Service Center My Lightdrop has a shorter runtime than 8 hours The LED POWER default setting is HIGH BRIGHTNESS To achieve a greater battery runtime set the LED POWER to NORMAL or MAXIMISE RUNTIME which will guarantee either 8 hrs or 15 hrs of operation Alternatively program the fixture to only display colors that use less power such as Red Green and Blue The charger is plugged in but my Lightdrop
3. Lightdrop AX3 USER MANUAL CONTENTS Lightdrop Charger Rubber Feet x4 Rubber Socket Plug User Manual Diffusor Dome Hooks x3 C FE Bracket c Manual Version 1 0 Date of Issue 15 07 14 Control Methods Lumen Radio Press the ON OFF button for 1 2 sec to turn it on or off Once on press the ON OFF button for 2 5 sec to place into BLUE MODE stop pressing when you see flashing blue When in BLUE MODE a firm tap on the ON OFF button will scroll through the colors being displayed To choose a color press the ON OFF button for 2 sec To FACTORY RESET press the ON OFF button for 5 sec until the fixture shows red color To use Astera s ARC1 remote control point at your lights and press your chosen effect color speed or brightness Astera s ARC2 remote control and Android application the AsteraApp can group many lights together address individual lights or groups of lights and send complex effects to all lights in range For additional information refer to the manual and quickstart guide for the ARC2 and ART6 at www astera led com downloads Connect an ART3 Wireless DMX Transmitter to your DMX desk to send wireless DMX signals to the AX3 You can set the AX3 s DMX address from any Astera RF remote controller The AX3 can also be controlled by CRMX Wireless DMX which also supports W DMxX from Wireless Solutions The pairing of AX3 to Transmitter is done automatically To unp
4. air simply do a FACTORY RESET as indicated above For additional information refer to the respective manufacturer s manual Key Functions Magnet Screw Threads for Hooks Tilt Wallwash Adjustor Rubber Feet Underside ON OFF Button Charging Socket Side ON OFF Bracket Adjustor ee Bracket Assembly a Attach diffusor dome place inside PE objects b Use as a angled spotlight with use of the bracket or attach truss clamp into hole in the center of bracket and affix to tables truss etc c Use as a wallwasher by extending the tilt thread d Attach the hooks and hang from the ceiling e Use the magnet and place underneath tables A amp www astera led com ASTERA m Astera LED Technology Nahestrasse 68 70 55593 R desheim an der Nahe Kreis Bad Krueznach Germany 49 0 671 92028292 Lightdrop Battery Status While on standby or during operation press the ON OFF button to check the status of the battery C Less than 30mins runtime O Up to 30mins runtime remaining recharge have been used Over 30mins runtime have been used Charging Only charge when the fixture is powered off The charging status colors below are only present in this state The ambient charging temperature is 0 35 C Slow flashing 0 35 C O Slow flashing 36 40 C charging at full current charging at reduced current Fast flashing lt 1 C or 241 C Fast flashing fixture is u
5. lunging it will cause FIRE or EXPLOSION Never store the battery when fully drained Always recharge immediately when empty Make sure to fully charge all units before storing them Partially charged batteries will lose capacity Do not store the unit for longer than 3 months without re charging The exterior surfaces of the Lightdrop can become hot up to 55 C during normal operation Ensure that accidential physical contact with the device is not possible Allow all Lightdrop devices to cool before servicing Use only Astera approved accessories to diffuse or modify the light beam Do not directly look at the light beam for long periods It can cause harm to your eyes Do not look into the beam at a distance of less than 0 5m 20 inches from the front surface of the product and do not look at LEDs with a magnifying glass or any other optical instrument that may concentrate the light output This product is for professional use only It is not intended for household use
6. nder overheating battery error charging has stopped Technical Data Item Codes Total LED Power Luminous Flux illuminance typical values on 6500K White Strobe Beam Angle Battery Battery Lifetime Operation LED Lifetime Charging Time Ambient Charging Temperature Working Voltage Input Current Wireless Module Range DMX Interface Optional DMX Interface Housing IP Rating Relative Humidity Operating Temperature Weight Dimensions Environment Features Included Accessories Also Available AX3 AX3 CRMX includes Lumen Radio CRMX 15W 1 x RGBW CREE LED Chip 850 Im on 6500K White 3000 Ix at 10m 760 Ix at 2m 0 25Hz 13 achieved through Khatod lens Built in Samsung battery 70 capacity after 300 charging cycles 5 15 hours 50 000 hours 5 20 hours depending on ambient temp 0 35 C 40 C max Input 110 240V 50 60Hz 2 5A at 5V 868MlHz receiver US 902 928MHz 2 4GHz wireless module 300m 330yds Wireless DMX with ART3 Transmitter CRMX Wireless DMX from Lumen Radio also supports W DMX Polyamide Polystyrene IP65 when rubber charging plug is inserted 0 100 non condensing 0 40 C 32 104 F 0 430kg 0 9lbs L119mm x H59mm x W110mmMm L5 1 x H2 3 x W4 3 Indoor Outdoor TruColor Calibration Temperature compensation Dynamic power boost Charger Diffusor Dome Hooks Bracket Rubber Feet x4 Charging Port Plug 17
Download Pdf Manuals
Related Search