Nirvana Warranty PDF
Contents
1. PICTURE 7 1 to circulation pump L2 or neutral to circulation pump L2 or neutral to power supply L1 to power supply DETAIL A SCALE 1 4 13 TRYDENT 5 8 OPERATING OF THE ECO ENERGETIC CONTACTOR Depending on heat pump instruction heating required If connected to the electrical box and the contactor NOTE The magnetic contactor is used to intelligently control pool pump while providing better energy efficiency of your heat pump PICTURE 7 The HP727S features an adjustable minimum filtration period FIL A daily 24 hour cycle is divided into 6 periods of 4 hours 240 minutes The adjustable setting values represent the minimum total daily hours that filtration is required FIL PARAMETER SETTINGS If connected to electrical box 2 hours to ORE 23 hours GN Pump operates between 2 and 23 hours a day Pump is always OFF Pump is always ON 1 In OFF mode the circulating pump needs to be always on or programmed by an external timer 2 In ON mode the circulating pump is always The minimum filtration time selector is divided into 6 equal periods per day E g Selection of 4 hours 6 periods 40 minutes per period The circulating pump will therefore operate 40 minutes of each period of 4 hours The minimum filtration time that can be selected is 2 hours 6 periods of 20 minutes each When the circulating pump is ON if there is a need for heating during a2. The green light means that in heating mode of the spa A WARNING The pump will go on and then the current water temperature will be displayed The current temperature displayed is kept in memory and displayed for 5 minutes until the water temperature sensor has sampled the circulating water After 5 minutes the water temperature is automatically updated and displayed ADJUSTING DESIRED TEMPERATURE Settings Pool OFF 61 F 95 OFF 16 C 35 C SPA option OFF 61 Fa 104 OFF 16 Ca 40 C 17 up TRYDENT The control is shipped set to OFF POOL and SPA mode option The heat pump stops automatically if a setting below 61 F 16 C is selected In OFF mode the control will display the water temperature Use the SET key to select POOL or SPA mode Use the T key to increase the desired setting to above 61 F 16 C The heat pump compressor operates automatically if a setting above 61 16 C is selected Adjust the settings to the desired value BACKWASH OPERATIONS Carry out the backwash procedure as follows 1 Turn OFF the power to the pump with power supply or FIL OFF POL OFF and SPA OFF 2 Prepare the system for backwash and power ON the pump with power supply or FIL ON 3 The circulating pump will go ON and the controller will not check for 5 minutes if water flow is present at the flow switch 4 You will have 5 min
3. 11 3 MANUFACTURER S LIMITED 2 20 11 4 WARRANTY 1 0 21 12 0 TROUBLESHOOTING 10 21 22 13 0 CONTACTING THE insita sensn 26 APPENDIX 1 OVERVIEW OF THE UNIT APPENDIX 2 HEAT EXCHANGER OVERVIEW APPENDIX 3 ELECTRIC BOX OVERVIEW APPENDIX 4 ELECTRIC PLAN OF THE ELECTRIC BOX p TRYDENT 1 0 INTRODUCTION Dear Owner Thank you for choosing TRYDENT heat pump inc You are now the proud owner of a TRYDENT pool heat pump that is industry recognized for its efficiency and reliability Very economical and extremely easy to operate your TRYDENT heat pump will ensure your full satisfaction and remain problem free for years to come if it is installed and maintained according to the instructions in the OWNER S MANUAL AND INSTALLATION GUIDE This appliance The Management TRYDENT heat pump Inc delivers the best value on the market 2 0 PRINCIPALS FEATURES OF YOUR TRYDENT SWIMMING POOL HEATER FIBERGLASS CABINET SUPERIOR COEFFICIENT OF PERFORMANCE COP SCROLL DANFOSS COMPRESSOR R 410A FREON ENVIRONNEMENTLY FRIENDLY OVERSIZED BLUE FINE EVAPORATOR VERY QUIET EAS
4. The heat pump will not re start after one of the protection devices shuts it down for the third time in the same hour Close the circuit breaker to reset the heat pump Digital control displays CODE SPI The digital control is defective Close the breaker switch and re open it If the problem is not resolved the digital control will have to be changed In this case call your dealer Digital control displays CODE DPO The de icing sensor is not properly connected or is not receiving power Call your dealer Digital control displays CODE PO The water temperature sensor is not properly connected or is not receiving power Call your dealer Digital control displays CODE DPC The de icing sensor is defective Call your dealer Digital control displays CODE PC The water temperature sensor is defective Call your dealer Heat is needed the fan is functioning no code is displayed and the compressor does not start Electrical problem in the compressor circuit Capacitor defective Compressor defective Call your dealer 23 p TRYDENT QUESTIONS ANSWERS HEAT PUMP FAILS TO OPERATE Is the display illuminated Is the green light illuminated If not ensure the breaker is turned ON The red light illuminates when the unit runs only fan compressor etc HEAT PUMP RUNNING BUT IS IT HEATING Is the air blowing out of the top of the unit noticeably cooler than the su
5. fan is on and the compressor is not in operation 11 0 WARRANTY 11 1 REGISTRATION OF WARRANTY Although NIRVANA HEAT PUMP INC heat pumps of are of high quality and are subject to all appropriate controls during manufacturing it is important to fill out the registration card WITHIN TEN DAYS OF PURCHASE to provide us with your contact information name and addresses so that we are able to contact you in the event of a product recall Without your co operation in completing the registration card TRYDENT heat pump Inc will be unable to advise you of this situation 11 2 CONSUMER S RESPONSABILITY REGISTRATION CARD The warranty registration card included with the Owner s Manual must be returned to Nirvana heat pump Inc within 10 days of purchase The customer is responsible for the cost of all calls for service made to obtain instructions on how to operate the system or to correct improper installation of the system that is not approved by TRYDENT heat pump inc and not in compliance with the instructions given in manual 19 TRY DENT This warranty does not cover the cost of preventive maintenance We suggest you contact an authorized TRYDENT heat pump Inc dealer for an annual inspection and preventive maintenance of your system MODEL AND SERIAL NUMBERS The model and serial numbers of the TRYDENT unit covered by this warranty must be clearly written on the registration card Verify that the numbers on the heat pump s data s
6. minimum PICTURE A CAUTION CHEMICAL PRODUCTS DISTRIBUTOR CHLORINATOR PICTURE The titanium condenser has the great advantage of offering almost total protection against the water s acidity or chemical products in the water Furthermore in order to decrease the risks of corrosion if a chemical product dispenser for chlorine or bromine is included with the filtration system an insulated check valve must be installed downstream in addition to the check valve in the automatic dispenser Yo NEVER INSTALL THE HEAT PUMP UPSTREAM FROM THE FILTER 5 3 BYPASS SYSTEM The use of a bypass valve system is not necessary for your heat pump to operate properly Your heat pump is equipped with a Full Flow type heat exchanger that provides optimum performance with a water flow of 208 litters minute 55 U S 46 imperial The heat exchanger was specifically designed to reduce to erosion to less than 296 Erosion is caused by water flowing at high speed and the sanding effect produced by particles suspended in the water sand chlorine etc To facilitate maintenance and winterizing however we strongly recommend installing a bypass and or service valve system The design of the heat exchanger makes it easy to drain off the water inside When the water pipes are disconnected in preparation for winterizing because the pool water intake is directly at the base of the cylinder
7. the cylinder empties completely by itself thus eliminating the risk of bursting due to freezing during cold weather p TRYDENT PICTURE 4 TABLE 1 ILLUSTRATION OF PARTS A OUTLET WATER VALVE B1 B2 amp B3 ASSEMBLY VALVE BYPASS INLET WATER VALVE D PART NOT REQUIRED ONLY FOR TEMPORARY ASSEMBLY TABLE 2 BYPASS SYSTEM ASSEMBLY B amp Bs TABLE 3 POSITION OF VALVES FOR CIRCULATION INTO THE HEAT PUMP TABLE 4 POSITION OF VALVES FOR DIVERSION OF WATER 10 up TRYDENT 5 4 WATER PRESSURE GAUGE The pipes connecting the different water filtration and heating components often include a large number of bypass and or service valves sometimes leading to inadequate or no water pressure PICTURE 5 The pressure gauge should read between 5 and 15 Psi A high water pressure reading on the filter gauge does not necessarily mean that enough water pressure is reaching the heat pump A good pressure should be held in the green section If the pressure is in the yellow section you have to do a backwash If the pressure is in red section you have a problem with the out water of the machine It might be a bad position of the bypass valve 5 5 OPERATION OF THE HEAT PUMP 1 The swimming pool water pump must always be ON when the heat pump is in operation If the swimming pool water pump is equipped with a timer make sure that the heat pump s operating time is synchronized with the water pump s operating tim
8. under any additional warranty provided by a distributor or dealer is the sole responsibility of that distributor or dealer The Service Warranty continues in effect insofar as the product remains at the owner s original address and was installed according to the standards and recommendations in the Owner s Manual or until the expiry of this warranty This warranty applies to the original purchaser and is transferable to successors only if the heat pump remains at the original installation site A WARNING This agreement may be transferred to a second owner at the same address by sending a written request to NIRVANA heat pump Inc accompanied by a check or money order in the amount of 100 00 Canadian taxes to cover transfer and administrative fees A WARNING REPLACEMENT OR REPAIR PURSUANT TO THE LIMITED WARRANTY CONSTITUTES THE SOLE REMEDY 11 4 WARRANTY EXCLUSIONS A IMPORTANT THIS LIMITED WARRANTY DOES NOT COVER DAMAGE OR IMPROPER OPERATION CAUSED a Improper use or maintenance of the heat pump that does not comply with the instructions in the Owner s Manual provincial or state building codes or municipal regulations 21 TRYDENT 12 0 b Improper installation of the heat pump or installation performed by persons not authorized by the Company Improper use negligence accident or force majeure which includes such events as flood lightning
9. 1 PICTURE 5 5 5 OPERATING OF THE 21 1 5 6 ELECTRICAL 21 1 41 sena en sena PICTURE 6 5 7 ENERGETIC 11 2 PICTURE 7 5 8 OPERATING OF THE ECO ENERGETIC HEAT PUMP MAINTENANCE POOL WATER MAINTENANCE 21 1 4 4 7 1 POOL WATER MAINTENANCE 2 nennen PICTURE 8 cg P MI OPERATION OF THE ELECTRONIC 1 2 TECHNICAL INFORMATPION nennen tnn tn nass sth sth ans uDunn 11 1 REGISTRATION OF 11 2 CONSUMER S 5 5 0 11 11 11 13 14 15 15 15 16 17 19 19 19 19 p TRYDENT
10. 2 RUE BURRILL SHAWINIGAN QUEBEC CANADA GON 6T6 TEL PHONE 819 539 8698 T LEC FAx 819 539 4431 SANS FRAIS TOLL FREE 1 866 443 4476 WWW NIRVANAHP COM INFO NIRVANAHP COM INSTALLATION INSTRUCTION MANUEL UPDATE 2010 01 26 TRY DENT
11. Jp TRYDENT MADE IN CANADA I MODELS E55 E70 E95 E110 CANADA INSTALLATION amp INSTRUCTION MANUAL SWIMMING POOL HEAT PUMP UNIT WARNING Read and comply with all safety information Make sure you understand all instructions before using this product WARNING DANGER In this manual these warnings mean there is a safety message to comply with or that improper use could result in damage to the unit When you see one read it carefully IMPORTANT In this manual this indication refers to the guarantee and procedures of service calls or referred to a recommendation 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 10 0 11 0 TABLE OF CONTENTS INTRODUCTION m PRINCIPAL FEATURES OF YOUR TRYDENT SWIMMING POOL HEATER OPERATING PRINCIPLES OF THE THERMODYNAMIC PICTURE 1 A OST c INSTALLATION OF YOUR HEAT 219 5 1 CHOICE OF INSTALLATION PICTURE 2 5 2 CONNECTING 1 1 2 2 11 PICTURE 3 5 3 Md RO Ezpds m PICTURE 4 5 4 WATER PRESSURE 1 1
12. Y TO OPERATE CARRY HANDLES lt lt lt lt lt 5 5 lt lt NEW DESIGN 3 0 OPERATING PRINCIPLES OF THE THERMODYNAMIC HEAT PUMP This heat pump comes equipped with a large surface heat collector A that allows the maximum heat to be extracted from the surrounding air The heat thus recovered is then transferred to the water in your swimming pool via the heat exchanger This method of heating generates substantial energy savings compared to conventional electric gas or oil pool heaters Finally the cold air is B expelled of the unit i p TRYDENT PICTURE 1 Cold air IMPORTANT SOLAR BLANKET In order to increase energy savings we strongly recommend use of a solar blanket when the air is cooler especially at night and at the beginning and end of the season This will minimize heat loss and help reduce your heating costs 4 0 ENERGY SAVING Did you know that at least 43 of heated pool owners choose heat pumps as pool heaters And with good cause This system has the highest output is the most economical to operate and is the advantageous for maintaining the water in your pool at a constant temperature day and night Using a pool heat pump continuously to keep the pool s water temperature at a constant 27 degrees Celsius 80 degrees Fahrenheit from May to September inclusively costs only one fifth of what it costs to use a natural gas or propane pool heater It also offers other
13. advantages such as no longer worrying about energy supply not being inconvenienced by combustion odors and protecting the environment from an ecological point of view p TRYDENT 5 0 INSTALLATION OF YOUR HEAT PUMP 5 1 CHOICE OF INSTALLATION SITE The installation site is a very important element in getting the most out of your pool heat pump As described earlier the heat pump captures energy from the air and transfers it to the pool water When choosing the installation site it is very important make sure there is enough room around the heat pump that is free of obstacles wall trees hedges etc The choice of site should allow easy access to the temperature control panel PICTURE 2 Concrete slab A level surface is required to ensure the stability of the heat pump We recommend using a concrete slab or patio stone In addition to durability these will not be affected by water condensation which may drip from the heat pump evaporator during operation 1 Water condensation is the result of hot humid air coming into contact with the cold surface of your heat pump s heat collecting coil p TRYDENT TRYDENT heat pumps must never be installed an enclosed area such as garage or shed 5 2 CONNECTING WATER 1 Connect the water line from the swimming pool filter to the WATER IN connector located at the base of the heat pump 2 Connect the water line returning to the swimming p
14. cing mode During cold weather frost may form on the evaporator This is normal However if you see 75 of ice or more contact us immediately REPAIR If your heat pump still does not operate after these verifications contact your seller or your manufacturer All replacements must be made with original parts in order to maintain your heat pump s proper performance durability and safety and continue your warranty It is prohibited to modify or remove a safety device The manufacturer disclaims all responsibility if installation instructions are not followed or if electrical or mechanical components and or safety devices have been modified in any way Notify us immediately of any warranty difficulties with the authorized vendor in your area 25 TRY DENT 13 0 CONTACTING THE FACTORY If you should need to call us for service or parts please have the following information ready that will speed the service process and allow us to respond more quickly Model Serial Number Retailer Installation Date Please call us toll free at 1 866 443 4476 We are here to serve you from 8 a m To 4 30 p m EST Monday through Friday If calling after hours leave a short message Be sure to leave your name and daytime telephone number If you prefer you may fax the information to 819 539 4431 Be certain to provide your full address and daytime telephone number Thank you NIRVANA HEAT PUMP INC 416
15. e with priority to the pool heater The pool heater may have to operate for longer periods than the water pump of the swimming pool 2 The heat pump may occasionally generate condensation in the form of mist when the relative humidity is at higher levels 3 The condensation formed on the heat collector may cause dripping under the heat pump 4 The use of a bypass valve system is always recommended to facilitate maintenance 5 When starting the heat pump the fan will start immediately but the compressor will take between 3 and 5 minutes to start up 5 6 ELECTRICAL CONNECTION The TRYDENT heat pump has been designed to enable simple easy and safe installation There is no need to open the heat pump and risk making a mistake in the electrical hook up All our models come with a junction box located at the base of the unit allowing quicker simpler heat pump hook up Note You will find the heat pump s electric plan at the end of this manual and on the inside of the electrical casing of your unit This one must be connected to a food of 240v single phase current 11 up TRYDENT PICTURE 6 TO POWER SUPPLY 12 Do the connection in the respect of the National provincial and local codes CAUTION To guarantee your safety and ensure proper operation of your unit the electrical hook up should be done by your POOL EXPERT or a CERTIFIED ELECTRICIAN according to national state or provincial and municipal codes A circuit br
16. eaker of sufficient rating and copper wire must be used and it may be necessary to install a ground PICTURE 6 A CAUTION The power cable ground wire must be connected to the electrical panel and to the ground terminal boards in the heat pump s junction box Improper installation increases the risk of fire and electrocution or injury 12 up TRYDENT A WARNING Units installed within 5 feet of the pool walls must be protected by a ground fault circuit breaker 5 7 ECO ENERGETIC CONTACTOR The eco energy contactor is an option of our electronic chart which makes it possible your Trydent unit to effectively manage the use of your circulating pump The latter does not need to function 24 hours a day Thus energy saving interesting for a better energetic efficiency This option will always privilege the attack of your required temperature versus the time of operation of the circulating pump Generally the professionals of industry intend themselves to say that the circulating pump can function approximately 12 hours per day without to affect water quality according to of course the conditions weather or of the system of treatment of water which you use Consult your swimming pool professional of the on this subject A WARNING To guarantee your safety and ensure proper operation of this option the electrical hook up should be done by your POOL EXPERT or a CERTIFIED ELECTRICIAN
17. earthquake tornado hail and any other unpredictable irresistible event known as an Act of God d Freezing or erosion of the piping or the internal components of the heat pump due to improper winterizing poor water quality infiltration of sand or other abrasive substances into the heat pump s internal workings e Premature corrosion of the titanium coolant tubing resulting from improper use of chemical products in the pool e g pH chlorine or salinity levels that are above or below the standard Modification alteration repair or replacement of parts performed by persons not authorized by the company TROUBLESHOOTING GUIDE PROBLEM Digital control displays CODE FLO MAINTENANCE amp TROUBLESHOOTING CODE CAUSE The water flow inside the heat pump is insufficient There is no water circulation inside the heat pump The flow switch is defective WHAT TO DO Check that the circulating pump is working Check that the bypass valves are properly positioned Check the skimmer no blockage Check the water pressure gauge of the heat pump it should read between 10 and 15 psi Digital control displays CODE FL3 The heat pump flow switch has cut off three 3 times in the same hour for one of the reasons above The heat pump will not re start after one of the protection devices shuts it down for the third time in the same hour Close the circuit breaker to reset the heat pump Digital contro
18. filtration period 1 The circulating pump will stay ON until heating is no longer needed 2 During that period the minimum filtration time counter meter is always on 3 If the minimum daily filtration time is reached and heat is still needed the circulation pump will stay ON until heat is no longer needed If the minimum daily filtration time is reached and heat is not needed there will still be 15 minutes of circulating time per period every 4 hours This is to sample the pool water temperature in case the water needs to be heated not valid if FIL parameter is set to OFF Whenever the FIL parameter is changed the daily counter will reset 14 up TRYDENT 6 0 HEAT PUMP MAINTENANCE A WARNING SAFETY TIPS A Acertified electrician should perform all electrical connections see the high voltage connection diagram B Always disconnect the heat pump before e Opening the access panel e Cleaning the swimming pool filter e Cleaning the cabinet e Cleaning the evaporator C Never sit or place heavy objects on the heat pump D Never put objects in or on the protective grille in order to avoid any risk of injury or breakage A Inspect and clean the pool filter regularly to ensure adequate water flow to the heat pump B Inspect the evaporator and clean it by rinsing carefully using a garden hose to direct a jet of water from the top to the bottom to prevent grass leaves or other objects from blocking the eva
19. heet match the numbers on the registration card You are responsible for informing Nirvana heat pump Inc if the identification numbers do not match PURCHASE INVOICE You must keep your original purchase invoice showing the date the heat pump was purchased the installation date and the model and serial numbers so that this information is always available for written or verbal communication with the technician dealer or manufacturer A IMPORTANT SERVICE CALL To make a call for service under the terms of this warranty you must communicate with your dealer and make sure you can provide the model of the appliance the serial number present the original invoice indicating the dates of purchase and installation of the heat pump and a detailed description of the problem A IMPORTANT READ THE ATTACHED LIMITED WARRANTY CERTIFICATE 11 3 MANUFACTURER S LIMITED WARRANTY NIRVANA HEAT PUMP offers a limited warranty against defects in the operation of the heat pump This warranty becomes effective from the date of installation with a proof of installation provided by the dealer and is valid only for new heat pumps residential sector only The heat pump must be installed according to manufacturer specifications and must be operated under the conditions of normal use recommended by the manufacturer During the life of the warranty NIRVANA HEAT PUMP INC agrees to repair or replace at its own discretion an
20. l displays CODE FS The heat pump is in de icing mode Wait until the end of the de icing cycle The heat pump will restart automatically Digital control displays CODE LP Ventilation on the evaporator is insufficient The fan does not work Freon leak The outside temperature is very low Check that the evaporator is not blocked by pollen grass leaves see the user s manual for safety and maintenance tips Be sure there is enough free space around the heat pump see the Installation Guide Check that the fan is powered ON Digital control displays CODE LP3 The heat pump low pressure switch has cut off three 3 times in the same hour for one of the reasons above The heat pump will not re start after one of the protection devices shuts it down for the third time in the same hour Close the circuit breaker to reset the heat pump 22 p TRYDENT Digital control displays CODE HP The water flow inside the heat pump is insufficient The bypass valve is in the wrong position The water exit is blocked There is a blockage in the refrigeration circuit piping blocked Check whether there is adequate water circulation inside Check that the bypass valves are properly positioned Check whether anything is blocking the water hose Digital control displays CODE HP3 The heat pump high pressure switch has cut off three 3 times in the same hour for one of the reasons above
21. ool to the WATER OUT connector located at the base of the heat pump 3 Once all connections are made turn the filter pump on to check water circulation and ensure that all connections are watertight The flow rate must be at least 208 litters minute 55 U S GPM 46 imperial GPM A circulation pump that reaches top performance with a flow of 208 litters minute 55 U S GPM 46 imperial GPM must be installed to ensure you achieve sufficient water flow minimum of 1 5 HP circulation pump is recommended PICTURE 3 Water out BB Water in e e Chlorine sanitzer 2 By Pass Valve cS R 3 2 7 One way valve 1 Hum Filter MINIMUM Pump recommended 1 5 HP Connecting your heat pump to your pool s water line is a simple operation that can be done by you or a qualified technician All you will need is flexible pipe 1 in diameter inside and stainless steel clamps It is also possible to use rigid PVC pipe but this method is generally more difficult and expensive i p TRYDENT CAUTION The titanium heat exchanger has a single wall This is not suitable for potable water A CAUTION The heat pump must be installed between the pool filter outlet and the swimming pool as close as possible to the filter pump and the electrical hook up circuit to minimize connection costs and increase performance Note that use of 90 elbows and short elbows should be kept to a
22. porator C Clean the heat pump cabinet with mild soap dishwashing soap Do not use abrasive products or products containing bleach D Make sure that the skimmer is not blocked 7 0 POOL WATER MAINTENANCE 7 1 POOL WATER MAINTENANCE CHART PICTURE 8 CHLORINE ALKALINITY HARDNESS ACIDITY BETWEEN BETWEEN BETWEEN ALMOST 1 amp 80 amp 120 150 amp 300 P P M 30 P P M 15 up TRYDENT A WARNING We recommend maintaining the pH level of the swimming pool at between 7 2 and 7 8 A higher pH level could damage the heat pump and other equipment and also void the warranty Also check the chlorine and the hardness of the water PICTURE 8 Before backwashing stop the unit by putting the thermostat to the lowest temperature during the cleaning cycle Never use the skimmer to add chemicals to your pool water These recommendations are important to prolong the life of your heat pump and especially to protect your health 8 0 WINTERIZING 1 Setthe circuit breaker to the OFF position 2 Drain the heat pump before the first frost Unscrew all water connections WARNING It is very important that all water connections to the pool are disconnected bypass valve or other to allow complete drainage of the heat pump 3 Rinse the inside of the heat exchanger cylinder with a stream of city water for about 15 minutes to make sure chlorine does not remain on
23. ranty Costs incurred by a refrigeration technician for a service call that was not authorized beforehand must be borne by the CUSTOMER A CAUTION BEFORE PLACING A CALL FOR SERVICE To avoid situations where a service call or repair is not covered by the warranty as described in the owner s manual we advise you to check that At all times 24 up TRYDENT There is always possibility of condensation especially if conditions are humid Condensation is the result of hot humid air coming into contact with the cold surface of your heat pump s coil Condensation should not be confused with leaking a The breaker or the fuse is ON and the heat pump is properly connected green indicator light on the unit b The circulating pump is running at full capacity is the right size 1 5 HP is recommended and the filters are clean C The gauge on the heat pump indicates between 10 and 15 psi for sufficient flow carry out a backwash d Service valves water intake and water outlet are in the open position and the bypass valve is closed The thermostat is set high enough f design of the plumbing is in keeping with best practices g The fins are not blocked by pollen leaves grass etc clean with a garden hose from top to bottom and not towards the inside of the machine h When the air temperature varies by about 7 C the heat pump may then enter a cycle of stops and starts as it goes into de i
24. rrounding air 9 F to 12 F difference is typical Be sure all air coil surfaces are free from obstructions roof overhangs landscaping walls fences etc can restrict air flow The heat pump needs good airflow to operate at peak efficiency How many hours day does the circulating pump operate Cooler weather conditions or heating to a higher than normal may necessitate running the heat pump for a longer period of time Was the heater sized considering the use of pool blanket A blanket can be useful in permitting shorter run times in turn leading to substantial energy cost savings What it the air outside temperature The heat pump may be in the defrost mode if air temperature are below 50 F or if the water temperature is around 77 F If the heater is in defrost the code FS will be displayed If air temperature are not cold but the heater remains in defrost contact your retailer WATER COMING FROM THE HEAT PUMP Is it a leak or just condensation from normal operation Here s how to find out Shut the heat pump off leaving the circulation pump running Within a few hours there should be a marked reduction in the amount of water seen around the bottom of the heat pump If the water appears to be drying up the water is probably harmless condensate indicative of normal operation TECHNICAL ASSISTANCE SERVICE SERVICE CALL NIRVANA heat pump Inc will authorize service only on heat pumps that are under war
25. the exchanger and cause premature wear to the heat pump Block the water intake or outlet and tilt the heat pump to the rear to remove any excess water 4 Block the water intake and outlet with rags or plastic to prevent access by small rodents or other animals It is always a good idea to cover the heat pump with the TRYDENT tarpaulin for additional protection see with your dealer for more information NOTE When you tilt the heat pump do not tilt more than 30 35 and always carry it vertically RESTARTING 1 Visually inspect the heat pump 2 Clean the swimming pool filter 3 Balance the PH Level of the pool water 4 Reconnect all water intake and outflow connections 5 Setthe circuit breaker back to the ON position 9 0 OPERATION OF THE ELECTRONIC CARD 16 up TRYDENT FRONT PANEL DESCRIPTION Appuyer sur s lectionner pour choisir Press select FEE POL Ali Ter Arat 2 23 Heures j its 2 23 Hours Always Un DECK EASE La HB Post the current temperature of water According to the programming it can post other parameters Button SET which is used to move in the various menus Button INCREASE which is used to increase the temperature of water Button DECREASE which is used to decrease the temperature of water The green light means that we are in heating mode of the swimming pool The red light means that the Trydent unit is in operation
26. utes of uninterrupted water flow to do the backwash 5 Stop the circulating pump use the power supply or FIL OFF Normally when the circulating pump is required for this operation and there is no water flow detected at the control the pump will automatically turn OFF This procedure will give a 5 minute period of uninterrupted water flow before the circulating pump turns OFF CHANGING THE DISPLAY FROM F TO C Factory defaults are in F Press and hold down the SET key until the message POL appears Press the SET key until F C is displayed Press the T key to select F or press the J key to select C RESETTING THE DISPLAY If a flashing PLE or CSE error message is displayed hold down the SET key until the error message is no longer displayed approx 4 seconds The control will be reset to the factory default Reprogram all the settings 10 0 TECHNICAL INFORMATION 18 up TRYDENT MODEL CHARACTERISTICS E55 E70 E95 E110 HEATING CAPACITY 55 000 BTU 70 000 BTU 95 000 BTU 110 000 BTU PERFORMANCE COP 5 6 5 75 5 70 5 30 BRAKER SIZE 30 40 50 50 VOLTAGE 208V 240V 208V 240V 208V 240V 208V 240V FREQUENCY 60 Hz 60 Hz 60 Hz 60 Hz PHASE 1PH 1PH 1PH 1PH COMPRESSOR SCROLL SCROLL SCROLL SCROLL GAS R 410 A R 410 A R 410 A R 410A DE ICING OPERATION During the evaporator coil de icing cycle FS will be displayed to indicate that the unit is de icing During this time the
27. y parts deemed defective by the technician or authorized representative of NIRVANA HEAT PUMP INC insofar as they have been used under appropriate conditions any and all replacement parts must be original parts or approved by TRYDENT HEAT PUMP INC for all swimming pool heat pumps manufactured by NIRVANA HEAT PUMP INC A IMPORTANT 20 TRYDENT The use of unauthorized parts voids this warranty The warranty is valid only as long as the pool heat pump is installed at the original address of the original purchaser Excepting written agreement to the contrary all repairs or replacements of defective parts by a qualified technician are guaranteed for the period not exceeding the initial term of this agreement Heat pumps are much more sophisticated than simple household appliances and servicing by a handyman is not recommended Have any servicing carried out by a recognized refrigeration technician A IMPORTANT Evidence of servicing or repairs carried out by a person other than a technician authorized by TRYDENT will result in the cancellation of this warranty The manufacturer will not be liable for accessory or indirect damage resulting from improper installation and from the use of or the inability to use the appliance The manufacturer offers no other warranty of any nature whatsoever No distributor or dealer is authorized to modify the terms and conditions of this warranty Coverage
Download Pdf Manuals
Related Search