user manual
Contents
1. Replace the new battery and install the cover back 1 Put the front cover bottom to 1 1 and press down 2 Push the front cover top to 2 1 CHOOSING A SUITABLE LOCATION The recommended mounting height is 160cm Don t let the device facing the window or the sunlight www zipato com Don t let the device facing the source of heat Like heater INSTALLATION In the first time add the device into the Z Wave network First make sure the primary controller is in the inclusion mode And then power on the device just take out the insulation Mylar in the back side of the device The device will auto start the NWI Network Wide Inclusion mode And it should be included in 5 seconds You will see the LED light ON one second Let Controller associate with Group 1 of the device any light switch that intend to be turned on when the device trig please associate to Group 2 of the device In the accessory pack There are two type of double coated tape one is thicker hereinafter referred to as A tape and another is thinner hereinafter referred to as B tape you can use A tape for the test at the beginning The right way for A tape installation is stick it to the position below tamper key The thicker tape won t let the tamper key close so the sensor will enter the test mode You may test if installed position is good or not by this way Testing Sponge A gt Pa2. everything under control MULTISENSOR QUAD QUICK ese a GUIDE v1 TRADEMARKS Zipato and the Zipato logo are registered Trademarks All other product names mentioned herein may be trademarks or registered trademarks of their respective companies NOTICE Although Zipato has attempted to ensure the accuracy of the content of this manual it is possible that this document may contain technical inaccuracies typographical or other errors Zipato assumes no liability for any error in this publication and for damages whether direct indirect incidental and consequential or otherwise that may result from such error including but not limited to loss of data or profits Zipato provides this publication as is without warranty of any kind either express or implied including but not limited to implied warranties of merchantability or fitness for a particular purpose The published information in the manual is subject to change without notice Zipato reserves the right to make changes in the product design layout and driver revisions without notification to its users This version of the Installation guide supersedes all previous versions ELECTROMAGNETIC COMPATIBILITY In proper state and when operated properly the product complies with all the requirements in respect of interference radiation according to EN 301 489 17 EN 301 489 1 and EN 300 328 The connections conducting HF signals must neither be manipulated no
3. UNITED STATES US version ph psm02 us RUSSIA RU version ph psm02 ru ISRAEL IS version ph psm02 is AUSTRALIA AU version ph psm02 au INDIA IN version ph psm02 in FREQUENCIES EUROPEAN UNION EU 868 42 MHz UNITED STATES US 908 42MHz RUSSIA RU 869 02MHz ISRAEL IS 916 02MHz AUSTRALIA AU 921 42MHz INDIA IN 865 20MHz LIMITED PRODUCT WARRANTY GENERAL TERMS Nothing in this Limited Product Warranty affects your statutory rights as a consumer The Limited Product Warranty set forth below is given by Tri plus grupa d o o Europe herein referred to as ZIPATO This Limited Product Warranty is only effective upon presentation of the proof of purchase Upon further request by ZIPATO this warranty card has to be presented too EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY ZIPATO MAKES NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ZIPATO EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD TO THE EXTENT ALLOWED BY LOCAL LAW THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES AGAINST ZIPATO THEY DO NOT HOWEVER AFFECT OR RESTRICT THE RIGHTS YOU HAVE AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM IN NO EVENT WILL ZIPATO BE LIABLE FOR LOSS OF DATA OR FOR IN
4. r 7 ee Back view After finish the test and decide to fix then you can remove tape A and mounting the sensor by using tape B This will close the tamper key and let the sensor enter normal mode ADDING TO Z WAVE NETWORK There are two tamper keys in the device one is in the back side another is in the front side They have the same function Both of them can inclusion exclusion reset or association from Z Wave network In the first time add the device into the Z Wave network First make sure the primary controller is in the inclusion mode And then power on the device just take out the insulation Mylar in the back side of the device The device will auto start the NWI Network Wide Inclusion mode And it should be included in 5 seconds You will see the LED light ON one second make your home smart INCLUSION Put the Z Wave Controller in inclusion mode Pressing tamper key three times within 1 5 seconds will enter inclusion mode After inclusion successful the device will wake to receive the setting command from Z Wave Controller in about 20 seconds EXCLUSION Put the Z Wave Controller in exclusion mode Pressing tamper key three times within 1 5 seconds will enter exclusion mode Node ID has been excluded RESET Pressing tamper key four times within 1 5 seconds and do not release the tamper key when you press it the 4th time and the LED will turn ON After 3 seconds the LED w
5. the LED also will light ON one second make your home smart When the event triggered the device will report the messages to the nodes in the group 1 The messages also include the temperature and the illumination level The user can switch the report by configuration setting NO 5 Caution In the Home Automation Mode if the environment luminance higher than the setting the device won t report the message When the event triggered if the environment luminance is less than the setting of the configuration setting NO 4 the device will emit the signal to turn ON the lighting equipment those nodes in the group 2 And delay a while to turn OFF the lighting equipment The delay time is setting by the configuration setting NO 9 The PIR motion re detected interval in the Test Mode fixed to 6 seconds In the Home Automation Mode will start detect before turn OFF the lighting equipment In the Security Mode according to the setting of configuration setting NO 8 Notice When the tamper key of the back side is in the released state the device always in the Test Mode no matter the DIP switch setting BATTERY INSTALLATION When the device report the low battery message The user should replace the battery to new one The way to open the front cover please follow below steps Using a tool like 1 to press 1 1 till hear a click sound Hold the front cover and pull back Hold the front cover and pull up
6. when the DIP Switch setting to program mode If bit1 is enabled the bit0 is useless Multi Sensor function switch Using bit to control Bit0 Disable magnetic integrate illumination Bit1 Disable PIR integrate Illumination Bit2 Disable magnetic integrate PIR Default is Disable Bit3 When Bit2 is 0 Enable the device is install in the same room with the light 0 In the same room Default 7 Customer Function PIR Re 8 Detect Interval Time Turn Off Light Time 10 Auto Report Battery Time Auto Report Door Window State Time Auto Report 12 Illumination Time Auto Report 13 Temperature Time 4 3 0 OxFF 3 127 4 127 1 127 1 127 1 127 1 127 1 In the different room Bit4 Disable delay 5 seconds to turn off the light when door window closed Bit5 Disable auto turn off the light after door window opened to turn on the light Notice If bit2 is zero this setting is useless Bit Enable temperature monitoring When this bit enable the temperature changed 3 degree Fahrenheit it will report And also the temperature over 140 degree Fahrenheit it will report every 64 seconds Customer function switch using bit control Bit2 Enable PIR super sensitivity mode In the security mode after the PIR motion detected setting the re detect time 8 seconds per tick and minimum time is 24 seconds default tick is 3 24 seconds Setting th
7. 000 Zagreb CROATIA TEL 385 0 1 4004 404 FAX 385 0 1 4004 405 DECLARATION OF CONFORMITY The Manufacturer Tri plus grupa d o o hereby declares that the product Zipabox Smart home controller 1 d In accordance with the following Directive s 2006 95 EC The Low Voltage Directive 89 336 EEC The Electromagnetic Compatibility Directive and 1999 5 EC R amp TT EC Directive is in conformity with the e applicable requirements of the following documents EN 61326 EN 61000 3 3 EN 61000 4 4 EN 61000 4 11 IEC EN 55011 EN 61000 6 2 EN 61000 4 5 EN 301 489 1 3 EN 300 220 2 EN 61000 4 2 EN 61000 4 6 AS NZS IEC 60335 2 97 EN 61000 3 2 EN 61000 4 3 EN 61000 4 8 EN 60335 1 www zipato com hereby declare that the equipment named above has been designed to comply with the relevant sections of the above referenced specifications The unit complies with all applicable Essential Requirements of the Directives Person responsible for this declaration Dean Janacek Certification Manager 01 09 2012 Changes or modifications not expressly approved Tri plus grupa d o o for compliance could void the user s authority to operate the equipment re THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Le pr sent appa
8. DIRECT SPECIAL INCIDENTAL CONSEQUENTIAL INCLUDING LOST PROFIT OR DATA OR OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE HOWEVER NOTHING IN THIS AGREEMENT LIMITS ZIPATO S LIABILITY TO YOU I IN THE EVENT OF DEATH OR PERSONAL INJURY TO THE EXTENT RESULTING FROM ZIPATO S NEGLIGENCE OR II TO THE EXTENT RESULTING FROM ANY FRAUDULENT MISREPRESENTATION ON THE PART OF ZIPATO OR III TO THE EXTENT ARISING UNDER PART 1 OF THE CONSUMER PROTECTION ACT 1987 OF THE UNITED KINGDOM SOME STATES OR COUNTRIES DO NOT ALLOW 1 A DISCLAIMER OF IMPLIED WARRANTIES 2 www zipato com 03 VACA everything under control MULTISENSOR QUAD QUICK re a GUIDE v1 A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR 3 LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS IN SUCH STATES OR COUNTRIES SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY TO YOU THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE OR FROM COUNTRY TO COUNTRY YOU ARE ADVISED TO CONSULT APPLICABLE STATE OR COUNTRY LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS This Limited Product Warranty applies to ZIPATO branded hardware products collectively referred to as ZIPATO Hardware Products sold by ZIPATO Europe its European subsidiaries affiliates authorized resellers or country distributors collectively refe
9. E OF THE CONFIGURATION SETTINGSIS 1 NO Name 2 Basic Set Level 3 PIR Sensitivity 4 Light Threshold 5 Operation Mode Multi 6 Sensor Function Switch Default OxFF 70 29 Valid Values 1 100 OxFF 0 99 0 100 0 127 0 127 www zipato com Description Setting the BASIC command value to turn on the light The 0xFF 1 means turn on the light For dimmer equipment 1 to 100 means the light strength PIR sensitivity settings 0 means disable the PIR motion 1 means the lowest sensitivity 99 means the highest sensitivity High sensitivity means can detected long distance but if there is more noise signal in the environment it will re trigger too frequency Setting the illumination threshold to turn on the light When the event triggered and the environment illumination lower then the threshold the device will turn on the light 0 means turn off illumination detected function And never turn on the light 1 means darkest 99 means brightest 100 means turn off illumination detected function And always turn on the light Notice In none test mode only the value in 1 to 99 will enable the illumination detected function and update the illumination value Operation mode Using bit to control Bit0 1 means security mode 0 means home automation mode Bit1 1 means enable test mode 0 means disable test mode Notice BitO and bit1 will effect
10. WI When the power on the device will check is it already adding to the network If doesn t it will auto start the NWI mode The LED will flash in every second and continue 30 seconds Until timeout or the device successful to inclusion by controller You can press the tamper key 3 times to abort the NWI mode WAKE When the power on the device will wake about 20 seconds In this duration the controller can communicate with the device Normally the device is always sleeping to save the battery energy FUNCTION DIP SWITCH There is one function DIP switch in front of the device Remove the front cover in the right top of the PCB and also has mark M1 and M2 for two switch ON ON Test Mode ON OFF Security Mode OFF ON Home Automation Mode Program Mode According to the OFF OFE configuration setting NO 5 to set the operation mode OPERATION MODE There are three operation modes of the device The user can choosing the suitable mode for application There are three modes Test Home Automation and Security Test Mode is for the user test the sensor function when installation Home Automation Mode focus in automatic to control the lighting equipment For convenience and save energy Security Mode focus in surveillance warning When the event triggered normally the LED won t indicated unless the battery is in the low level the LED will flash once And in the Test Mode
11. al environment temperature like freeze sensor or fire sensor to send the warning message make your home smart FIGURE 1 Dimensions unit mm ILLUMINATION SENSOR LENS Profile view Top bottom view FEATURES 1 Door window 2 PIR 3 illumination and 4 temperature functions in one sensor Adopt newest Z wave 400 series chip support multichannel operation and higher data rate 9 6 40 100kbps Higher output power 2 5dBm output power as compared to 2 5dBm 300 series Z wave module to enhance the communication range 1500mA CR123A lithium battery to guarantee 2 year battery life Built in light sensor while applied to light control Adopt Z Wave protocol to secure the success of wireless two way communication With Tamper proof protection Easy install Low battery indication Z Wave V6 02 Z Wave Certificated No PSM02 1 ZC08 13050003 Auto report the open close status and battery status FCC part15 249 EN300 220 1 certification NCC APPLICATION PSM02 is a special device combining both PIR and Door window functions The benefits of combining Door window with PIR in one sensor can be observed in the following scenarios O The ambient lighting would be lower than default setting value after sunset If the PSM02 was installed on the inner side of door www Zzipato com G WAVE Ne Front view Back view in the house PSM02 would detect coming in people then the light would be turned on f
12. e suitable value to prevent received the trigger signal too frequency Also can save the battery energy Notice If this value bigger than the configuration setting NO 9 There isa period after the light turned off and the PIR not detecting After turn on the light setting the delay time to turn off the light when the PIR motion is not detected 8 seconds per tick and minimum time is 32 seconds default tick is 4 32 seconds The interval time for auto report the battery level 30 minutes per tick and minimum time is 30 minutes default tick is 12 6 hours The interval time for auto report the door window state 30 minutes per tick and minimum time is 30 minutes default tick is 12 6 hours The interval time for auto report the illumination 30 minutes per tick and minimum time is 30 minutes default tick is 12 6 hours The interval time for auto report the temperature 30 minutes per tick and minimum time is 30 minutes default tick is 12 6 hours make your home smart Z WAVE MESSAGE REPORT Z WAVE SUPPORTED COMMAND CLASS COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_VERSION COMMAND_CLASS_SENSOR_BINARY_V2 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_SENSOR_MULTILEVEL_V5 COMMAND_CLASS_BATTERY COMMAND_CLASS_BASIC MODELS AND FREQUENCIES MODELS EUROPEAN UNION EU version ph psm02 eu
13. e updates for Zipato products and services www zipato com CONTACT SUPPORT E MAIL support zipato com Mon Fri 9 00am 05 00pm CET make your home smart SPECIFICATION POWER 3V CR123A 48 uA 37mA 2 6V RF REGULATION FCC part15 249 EN300 220 1 DISTANCE min 40m indoor min 100m outdoor MECHANICAL WEIGHT DIMENSION Wx H x D Detector 28 x 96 x 23 mm Magnet 10 x 50 x 12 mm 520 BATTERY CR123A BATTERY LIFE 1500mAh gt 2 years ENVIRONMENT OPERATION TEMPERATURE HUMIDITY Normal environment temperature 10 40 C to have better PIR and battery performance 85 RH max TEMPERATURE DETECT RANGE 10 70 C ILLUMINATION RANGE 0 500 LX PIR DETECTION ANGLE HORIZONTAL 0 8 10M 90 6 8M HARDWARE MAGNETIC GAP MAGNETIC GAP OPENCLOSE CLOSE gt OPEN 28 MM 30 MM www zipato com 01 L zipato everything under control MULTISENSOR QUAD QUICK re GUIDE v1 POWER UP PROCEDURE BATTERY POWER CHECK When the power up the device will detect the power level of the battery immediately If the power level is too low the LED will continue flash about 5 seconds Please change another new battery PIR WARM UP When the power on the PIR need to warm up before operation The warm up time about 1 minute the LED will flash in every 2 seconds After finish the procedure the LED will light ON three times N
14. ill turn OFF after that within 2 seconds release the tamper key If successful the LED will light ON one second Otherwise the LED will flash once 3 IDs are excluded and all settings will reset to factory default ASSOCIATION Have Z Wave Controller entered association mode Pressing tamper key three times within 1 5 seconds will enter association mode Note The device support 2 groups The group 1 is for receiving the report message like triggered event temperature illumination etc The group 2 is for light control the device will send the Basic Set command to this group Including a node ID allocated by Z Wave Controller means inclusion Excluding a node ID allocated by Z Wave Controller means exclusion Failed or success in including excluding the node ID can be viewed from Z Wave Controller Notice Always Reset a Z Wave device before trying to add it to a Z Wave network Notice When the device into NWI mode the sensor functionality will useless The NWI mode will timeout after 30 seconds You can press the tamper key 3 times to abort the NWI mode Z WAVE NOTIFICATION After the device adding to the network it will wake up once per day in default When it wake up it will broadcast the Wake Up Notification message to the network and wake up 10 seconds for receive the setting commands The wake up interval minimum setting is 30 minutes and maximum setting is 120 hours And the interval step is 30 minute
15. in the first and last boxes in the table below this Limited Product Warranty extends only to the original end user purchaser of this ZIPATO Hardware Product and is not transferable to anyone who obtains ownership of the ZIPATO Hardware Product from the original end user purchaser PRODUCT WARRANTY PERIOD TABLE PRODUCT TYPE Multisensor Quad PRODUCT WARRANTY PERIOD One 1 year IMPORTANT The content of Product Type listed above is subject to change please refer to the www zipato com for latest update PERFORMANCE OF THE LIMITED PRODUCT WARRANTY If a product defect occurs ZIPATO s sole obligation shall be to repair or replace any defective Zipato Hardware Product free of charge provided it is returned to an Authorized ZIPATO Service Centre during the Limited Warranty Period Such repair or replacement will be rendered by ZIPATO at an Authorized ZIPATO Service Centre All component parts or hardware products that are replaced under this Limited Product Warranty become the property of ZIPATO The replacement part or product takes on the remaining Limited Warranty Period of the replaced part or product The replacement product need not be new or of an identical make model or part ZIPATO may in its discretion replace the defective product or any part thereof with any reconditioned equivalent or superior product in all material respects to the defective product WARRANTOR Tri plus grupa d o o Banjavciceva 11 10
16. nfiguration setting NO 6 bit to 1 When the temperature plus or minus three degree Fahrenheit 1 67 degree Celsius the device will report temperature information to the nodes in the group 1 The device will measure the temperature in every 64 seconds And if the temperature is over 140 degree Fahrenheit 60 degree Celsius the device also report in each measurement ILLUMINATION REPORT When the PIR motion detected or the door window state changed the device will unsolicited to send the Sensor Multilevel Report to the nodes in the group 1 Sensor Type Luminance 0x03 Note To disable this functionality by setting the configuration setting NO 5 the bit4 of the value to 1 TIMING REPORT Beside the event triggered could report message the device also support the timing unsolicited report of the status Battery level report Every 6 hours report once in default It could be changed by configuration setting NO 10 Low battery report When the battery level is too low every 30 minutes will report once Door window state report Every 6 hours report once in default It could be changed by configuration setting NO 11 Illumination level report Every 6 hours report once in default It could be changed by configuration setting NO 12 Temperature report Every 6 hours report once in default It could be changed by configuration setting NO 13 make your home smart Z WAVE CONFIGURATION SETTINGS NOTICE THE DATA SIZ
17. om that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help DISPOSING AND RECYCLING YOUR PRODUCT H This symbol on the product or packaging means that according to local laws and regulations needs to be disposed of separately from household waste and sent to recycling because it contains electronic components Once this product has reached the end of its life please take it to a collection point recycle facilites designated by your local authorities some will accept your product for free or simply drop it off at your Zipato re seller store By recycling the product and its packaging in this manner you help to conserve the environment and protect human health At Zipato we understand and are committed to reducing any impact our operations and products may have on the environment To minimize this impact Zipato designs and builds its products to be as environmentally friendly as possible by using recyclable low toxic materials in both products and packaging make your home smart COPYRIGHT 2014 Tri plus grupa d o o All Rights Reserved No part of this manual may be reproduced or transmitted in any form without the expressed written permission of Tri plus grupa d o o www zipato com 04
18. or the better illumination by radio transmission Furthermore PSM02 can be applied in a bathroom and it may turn on off light and fan automatically PSM02 can be taken as a portal chime at front desk of hotel or restaurant by sending out signal to P Gateway PSC01 as reminder which can be connected with speaker to turn the volume up It can be kept silent when customer leaving O For SMEs Small and medium enterprises PSM02 plays an important role in working hours and non working hours When non working hours PSM02 plays as security motion sensor protects the office from intruders At working hours PSM02 4 in 1 sensor can be applied to curtain or heater cooler controller for energy saving issue although some people may use thermostat to control heater cooler however PSM02 sensor can be smarter choice Since it can detect the people s activities and shutdown machine when no one exists or no movements In the past a digital home starter KIT includes many different sensors with very high price Right now Using the 4 in 1 patented sensor and a 4in 1 gateway PSC01 Siren speaker light IP based controller carry out home security safety automation in one box and provide customer full experience of digital life and flexibility in installation with affordable price TECHNICAL SUPPORT Having trouble installing your new product Zipato s website contains the latest user documentation and softwar
19. r damaged TAKE CARE OF YOUR SAFETY Display extreme caution when using ladders or steps please follow manufacturer s instructions Be careful when using hand and power tools and follow the manufacturer s guidelines when using them Take care that the correct tools are used Wear goggles or protective clothing where required INTRODUCTION The 4 in 1 multi sensor is designed to meet the requirement of integrate 4 sensors into one housing 1 Door window 2 PIR 3 illumination and 4 temperature When the detector is cooperated with security appliances the 1 Door window or 2 PIR sensor act as an alarm detector Alternatively when the detector is worked with Z Wave controller the detector can be set to perform the role of home automation device by detecting both changes in PIR motion detect or door window open close signal with percentage of illumination lux levels One scenario Is once night falls the percentage of ambient illumination is lower than preset value If a person moves within or across the devices field of vision a trigger radio signal will be transmitted so as to turn connected lightings for better illumination Another scenario is to combine 1 Door window 2 PIR 3 illumination sensors to recognize people is coming in or going out and turn the light on off automatically The temperature sensor can detect the temperature so as to adjust heater or cooler to achieve preset temperature or detect the abnorm
20. ree or that all deficiencies errors defects or non conformities will be corrected This warranty shall not apply to problems resulting from a unauthorized alterations or attachments b negligence abuse or misuse including failure to operate the product in accordance with specifications or interface requirements c improper handling d failure of goods or services not obtained from ZIPATO or not subject to a then effective ZIPATO warranty or maintenance agreement e improper use or storage or f fire water acts of God or other catastrophic events This warranty shall also not apply to any particular product if any ZIPATO serial number has been removed or defaced in any way ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A make your home smart RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS FOR THE ZIPATO HARDWARE PRODUCT LIMITED PRODUCT WARRANTY PERIOD The Limited Product Warranty Period starts on the date of purchase from ZIPATO Your dated sales or delivery receipt showing the date of purchase of the product is your proof of the purchase date You may be required to provide proof of purchase as a condition of receiving warranty service You are entitled to warranty service according to the terms and conditions of this document if a repair to your ZIPATO branded hardware is required within the Limited Product Warranty Period Other than in respect of products for domestic use in particular those listed
21. reil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence Lexploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lec trique subi m me si le brouillage est susceptible d en comprom ettre le fonctionnement NOTE Changes or modifications not expressly approved by Zipato for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet ona circuit different fr
22. rred to as ZIPATO Resellers with this Limited Product Warranty The term ZIPATO Hardware Product is limited to the hardware components and all its internal components including firmware The term ZIPATO Hardware Product DOES NOT include any software applications or programs GEOGRAPHICAL SCOPE OF THE LIMITED PRODUCT WARRANTY This Limited Product Warranty is applicable to Hardware Products sold by Zipato Resellers in all countries listed at the beginning of this document under the heading Countries in which this ZIPATO Limited Product Warranty applies The Limited Product Warranty will be honored in any country where ZIPATO or its authorized service providers offer warranty service subject to the terms and conditions set forth in this Limited Product Warranty However warranty service availability and response times may vary from country to country and may also be subject to registration requirements LIMITATION OF PRODUCT WARRANTY ZIPATO warrants that the products described below under normal use are free from material defects in materials and workmanship during the Limited Product Warranty Period set forth below Limited Product Warranty Period if the product is used and serviced in accordance with the user manual and other documentation provided to the purchaser at the time of purchase or as amended from time to time ZIPATO does not warrant that the products will operate uninterrupted or error f
23. s If the user want to wake up the device immediately please remove the front cover and press the tamper key once The device will wake up 10 seconds Z WAVE MESSAGE REPORT MOTION REPORT When the PIR motion detected the device will unsolicited to send the Sensor Binary Report to the nodes in the group 1 Sensor Type Motion 0x0C Sensor Value OxFF DOOR WINDOW REPORT When the Door Window state changed the device will unsolicited to send the Sensor Binary Report to the nodes in the group 1 Sensor Type Door Window 0x0A Sensor Value 0x00 is closed OxFF is opened www zipato com 02 everything under control MULTISENSOR QUAD QUICK re GUIDE v1 TAMPER REPORT When the 2 tamper keys in the device are pressed over 5 seconds The device will into the alarm state In that state if any one of the tamper keys be released the device will unsolicited to send the Sensor Binary Report to the nodes in the group 1 Sensor Type Tamper 0x08 Sensor Value OxFF TEMPERATURE REPORT When the PIR motion detected or the door window state changed the device will unsolicited to send the Sensor Multilevel Report to the nodes in the group 1 Sensor Type Temperature 0x01 Note To disable this functionality by setting the configuration setting NO 5 the bit5 of the value to 1 Temperature differential report This function default is disabled to enable by setting the co
Download Pdf Manuals
Related Search